Skip to contentSkip to conversation

Add support for Baijie Helper A133 board

PATCH Superseded Alexander Sverdlin 3 participants 16 messages Jun 5 – Jun 13

Subsystems (5)

v4 of 5 Superseded Latest is v5 →

lore
Share & tools
lore
#0 lore raw

v4 cover Add support for Baijie Helper A133 board

Baijie Helper A133 board is a development board around Baijie A133 Core SBC. Features:

- 1/2/4GiB LPDDR4 DRAM
- 8/16/32GiB eMMC
- AXP707 PMIC
- USB-C OTG port in peripheral mode (via onboard hub)
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- Gigabit Ethernet
- Bluetooth
- WiFi

Add initial support for both the Helper and Core boards, including UART, PMU, eMMC, USB, Ethernet, LRADC-connected buttons.

UART1 can only be used for Bluetooth module, but BT-WiFi combo Allwinner AW869A chip has not mainline driver currently.

Changelog:
v4:
- reserve RAM for ATF
- sun4i-lradc-keys: Add A100/A133 compatible
- dt-bindings: renamed "Baijie Helper A133" -> "Baijie A133 HelperBoard"
- dt-bindings: renamed "baijie,helper-a133" -> "baijie,helperboard-a133"
- dt-bindings: introduced allwinner,sun50i-a100-lradc
- reserve RAM for ATF
- renamed "sun50i-a133-baijie-helper.dtb" -> "sun50i-a133-helperboard.dtb"
- added "model" property into root of sun50i-a133-helperboard-core.dtsi
- added "cap-mmc-highspeed" and "max-frequency" into &mmc2
- added "x-powers,drive-vbus-en" and "*-supply" into &axp803
- dropped all "regulator-enable-ramp-delay" properties
- replaced &reg_dcdc3 with a "polyphased" comment
- exact DRAM voltage in &reg_dcdc5
- disabled &reg_dcdc6 to avoid "[ 31.710641] dcdc6: disabling"
- added &reg_vdd5v "root" regulator
- added "disable-wp" into &mmc0
- commented &usb_otg
- assigned usb1_vbus-supply in &usbphy
v3:
- added lradc node to sun50i-a100.dtsi
- enabled LRADC driver in arm64 defconfig
- added my copyrights into the newly introduced DTs
- all DT nodes sorted alphabetically
- all always-on regulators commented/propetly named
- all regulators got proper voltages (not default ranges)
- ADC-sensed buttons K1..K5 added
- re-labelled "eth_phy" -> "rgmii_phy"
- usbphy 0 switched from host into peripheral mode (downstream from an onboard hub)
- typo sun50i-a133-baije-core.dtsi -> sun50i-a133-baijie-core.dtsi
- https://lore.kernel.org/all/[email protected]/
v2:
- introduced baijie,helper-a133-core compatible for the Core (SoM) board
- https://lore.kernel.org/all/[email protected]/
v1:
- https://lore.kernel.org/all/[email protected]/

Alexander Sverdlin (7):
arm64: defconfig: Enable Allwinner LRADC input driver
dt-bindings: vendor-prefixes: Add Shenzhen Baijie Technology Co., Ltd.
dt-bindings: arm: sunxi: Add Baijie HelperBoard A133 compatible
dt-bindings: input: sun4i-lradc-keys: Add A100/A133 compatible
arm64: dts: allwinner: a100: Add LRADC node
arm64: dts: allwinner: a100: reserve RAM for ATF
arm64: dts: allwinner: A133: add support for Baijie Helper A133 board

 .../devicetree/bindings/arm/sunxi.yaml        |   6 +
 .../input/allwinner,sun4i-a10-lradc-keys.yaml |   1 +
 .../devicetree/bindings/vendor-prefixes.yaml  |   2 +
 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../arm64/boot/dts/allwinner/sun50i-a100.dtsi |  25 +++
 .../sun50i-a133-helperboard-core.dtsi         | 197 ++++++++++++++++++
 .../dts/allwinner/sun50i-a133-helperboard.dts | 148 +++++++++++++
 arch/arm64/configs/defconfig                  |   1 +
 8 files changed, 381 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard-core.dtsi
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard.dts
Signature · 1 line
2.54.0
#1 lore raw

PATCH v4 1/7 arm64: defconfig: Enable Allwinner LRADC input driver

Enable Allwinner LRADC input driver as module to support buttons on Baijie HelperBoard A133.

---
Changelog:
v4:
- no changes
v3:
- new patch

 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
index 96ce783f24e7..faf6d86d0555 100644
@@ -479,6 +479,7 @@ CONFIG_KEYBOARD_GPIO=y
 CONFIG_KEYBOARD_GPIO_POLLED=m
 CONFIG_KEYBOARD_SNVS_PWRKEY=m
 CONFIG_KEYBOARD_IMX_SC_KEY=m
+CONFIG_KEYBOARD_SUN4I_LRADC=m
 CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_KEYBOARD_MTK_PMIC=m
 CONFIG_MOUSE_ELAN_I2C=m
Signature · 1 line
2.54.0
#3 lore raw

PATCH v4 2/7 dt-bindings: vendor-prefixes: Add Shenzhen Baijie Technology Co., Ltd.

In reply to Alexander Sverdlin

Shenzhen Baijie Technology Co., Ltd. focuses on R&D and production of embedded products as well as customization of embedded solutions.

---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
index 28784d66ae7b..095cf654787f 100644
@@ -229,6 +229,8 @@ patternProperties:
     description: Azoteq (Pty) Ltd
   "^azw,.*":
     description: Shenzhen AZW Technology Co., Ltd.
+  "^baijie,.*":
+    description: Shenzhen Baijie Technology Co., Ltd.
   "^baikal,.*":
     description: BAIKAL ELECTRONICS, JSC
   "^bananapi,.*":
Signature · 1 line
2.54.0
#4 lore raw

PATCH v4 3/7 dt-bindings: arm: sunxi: Add Baijie HelperBoard A133 compatible

In reply to Alexander Sverdlin

Baijie HelperBoard A133 is a development board around their A133 Core board. Introduce a compatible for both the Core and the development boards.

---
Changelog:
v4:
- renamed "Baijie Helper A133" -> "Baijie A133 HelperBoard"
- renamed "baijie,helper-a133" -> "baijie,helperboard-a133" v3:
- no separate section for "core" .dtsi
v2:
- introduced baijie,helper-a133-core compatible for the Core (SoM) board

 Documentation/devicetree/bindings/arm/sunxi.yaml | 6 ++++++
 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +6 -0
index e6443c266fa1..82dd58b95f8a 100644
@@ -96,6 +96,12 @@ properties:
           - const: allwinner,ba10-tvbox
           - const: allwinner,sun4i-a10
 
+      - description: Baijie A133 HelperBoard
+        items:
+          - const: baijie,helperboard-a133
+          - const: baijie,helperboard-a133-core
+          - const: allwinner,sun50i-a100
+
       - description: BananaPi
         items:
           - const: lemaker,bananapi
Signature · 1 line
2.54.0
#5 lore raw

PATCH v4 4/7 dt-bindings: input: sun4i-lradc-keys: Add A100/A133 compatible

In reply to Alexander Sverdlin

The Allwinner A100/A133 SoCs have an LRADC which is compatible with the versions in existing SoCs. Add a compatible string for A100, with the R329 fallback.

---
Changelog:
v4:
- new patch

 .../bindings/input/allwinner,sun4i-a10-lradc-keys.yaml           | 1 +
 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml +1 -0
index 6bdb8040be65..524c8b51f53f 100644
@@ -23,6 +23,7 @@ properties:
       - const: allwinner,sun50i-r329-lradc
       - items:
           - enum:
+              - allwinner,sun50i-a100-lradc
               - allwinner,sun50i-h616-lradc
               - allwinner,sun20i-d1-lradc
           - const: allwinner,sun50i-r329-lradc
Signature · 1 line
2.54.0
#7 lore raw

PATCH v4 5/7 arm64: dts: allwinner: a100: Add LRADC node

In reply to Alexander Sverdlin

A100/A133 SoCs feature a Low Rate ADC (LRADC) for Key application.

Specs:
- Power supply voltage: 1.8 V
- Reference voltage: 1.35 V
- Interrupt support
- Support Hold Key and General Key
- Support normal, continue and single work mode
- 6-bits resolution, sample rate up to 2 kHz
- Voltage input range between 0 and 1.35 V

---
Changelog:
v4:
- added allwinner,sun50i-a100-lradc compatible
v3:
- new patch

 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +9 -0
index b3fb1e0ee796..7cb06b19b5a5 100644
@@ -466,6 +466,15 @@ ths: thermal-sensor@5070400 {
 			#thermal-sensor-cells = <1>;
 		};
 
+		lradc: lradc@5070800 {
+			compatible = "allwinner,sun50i-a100-lradc", "allwinner,sun50i-r329-lradc";
+			reg = <0x05070800 0x400>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_LRADC>;
+			resets = <&ccu RST_BUS_LRADC>;
+			status = "disabled";
+		};
+
 		usb_otg: usb@5100000 {
 			compatible = "allwinner,sun50i-a100-musb",
 				     "allwinner,sun8i-a33-musb";
Signature · 1 line
2.54.0
maintainer Reviewed-by on v4 5/7
#8 lore raw

Re: [PATCH v4 5/7] arm64: dts: allwinner: a100: Add LRADC node

Dne petek, 5. junij 2026 ob 09:09:19 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):

Quoted 27 lines

A100/A133 SoCs feature a Low Rate ADC (LRADC) for Key application.

Specs:
- Power supply voltage: 1.8 V
- Reference voltage: 1.35 V
- Interrupt support
- Support Hold Key and General Key
- Support normal, continue and single work mode
- 6-bits resolution, sample rate up to 2 kHz
- Voltage input range between 0 and 1.35 V

---
Changelog:
v4:
- added allwinner,sun50i-a100-lradc compatible
v3:
- new patch

 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +0 -0
index b3fb1e0ee796..7cb06b19b5a5 100644

arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi ths: thermal-sensor@5070400 { · line 470

Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +2 -0
@@ -466,6 +466,15 @@ ths: thermal-sensor@5070400 {
 			#thermal-sensor-cells = <1>;
 		};
 
+		lradc: lradc@5070800 {
+			compatible = "allwinner,sun50i-a100-lradc", "allwinner,sun50i-r329-lradc";

Break this into two lines, like usb_otg below. With that:

Best regards,
Jernej Skrabec

Quoted 11 lines
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +7 -0
+			reg = <0x05070800 0x400>;
+			interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_LRADC>;
+			resets = <&ccu RST_BUS_LRADC>;
+			status = "disabled";
+		};
+
 		usb_otg: usb@5100000 {
 			compatible = "allwinner,sun50i-a100-musb",
 				     "allwinner,sun8i-a33-musb";
#9 lore raw

PATCH v4 6/7 arm64: dts: allwinner: a100: reserve RAM for ATF

In reply to Alexander Sverdlin

Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address 0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.

---
Changelog:
v4:
- new patch

 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16 -0
index 7cb06b19b5a5..d8391663fd1d 100644
@@ -87,6 +87,22 @@ osc32k: osc32k-clk {
 		#clock-cells = <0>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 256 KiB reserved for Trusted Firmware-A (BL31).
+		 * This is added by BL31 itself, but some bootloaders fail
+		 * to propagate this into the DTB handed to kernels.
+		 */
+		secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x40000>;
+			no-map;
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13
Signature · 1 line
2.54.0
maintainer
#10 lore raw

Re: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF

Dne petek, 5. junij 2026 ob 09:09:20 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):

Quoted 7 lines

Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address 0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.

NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.

Best regards,
Jernej Skrabec

Quoted 36 lines

---
Changelog:
v4:
- new patch

 arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16 -0
index 7cb06b19b5a5..d8391663fd1d 100644
@@ -87,6 +87,22 @@ osc32k: osc32k-clk {
 		#clock-cells = <0>;
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 256 KiB reserved for Trusted Firmware-A (BL31).
+		 * This is added by BL31 itself, but some bootloaders fail
+		 * to propagate this into the DTB handed to kernels.
+		 */
+		secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x40000>;
+			no-map;
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13
#11 lore raw

Re: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF

Hi Jernej,

Quoted 11 lines · Jernej Škrabec

Dne petek, 5. junij 2026 ob 09:09:20 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):

Quoted 7 lines

Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address 0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.

NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.

like in commit 0d17c865118881609ea7e381c7cadbb7979cc596 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")

? ;-)

Quoted 38 lines

Best regards,
Jernej Skrabec

Quoted 35 lines

---
Changelog:
v4:
- new patch

  arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++

  1 file changed, 16 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +0 -0
index 7cb06b19b5a5..d8391663fd1d 100644
@@ -87,6 +87,22 @@ osc32k: osc32k-clk {
   		#clock-cells = <0>;
   	};

arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16 -0
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 256 KiB reserved for Trusted Firmware-A (BL31).
+		 * This is added by BL31 itself, but some bootloaders fail
+		 * to propagate this into the DTB handed to kernels.
+		 */
+		secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x40000>;
+			no-map;
+		};
+	};
+

   timer {
   compatible = "arm,armv8-timer";
   interrupts = <GIC_PPI 13

Signature · 1 line
Alexander Sverdlin.
maintainer
#12 lore raw

Re: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF

Dne sobota, 13. junij 2026 ob 10:34:42 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):

Quoted 16 lines

Hi Jernej,

Quoted 11 lines · Jernej Škrabec

Dne petek, 5. junij 2026 ob 09:09:20 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):

Quoted 7 lines

Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address 0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.

NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.

Quoted 5 lines

like in commit 0d17c865118881609ea7e381c7cadbb7979cc596 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")

? ;-)

I was against that too.

It's time to be fixed in bootloader.

Best regards,
Jernej

Quoted 41 lines
Quoted 39 lines

Best regards,
Jernej Skrabec

Quoted 35 lines

---
Changelog:
v4:
- new patch

  arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++
  1 file changed, 16 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16 -0
index 7cb06b19b5a5..d8391663fd1d 100644
@@ -87,6 +87,22 @@ osc32k: osc32k-clk {
  		#clock-cells = <0>;
  	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 256 KiB reserved for Trusted Firmware-A (BL31).
+		 * This is added by BL31 itself, but some bootloaders fail
+		 * to propagate this into the DTB handed to kernels.
+		 */
+		secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x40000>;
+			no-map;
+		};
+	};
+
  	timer {
  		compatible = "arm,armv8-timer";
  		interrupts = <GIC_PPI 13
#13 lore raw

Re: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF

Hi Jernej,

Quoted 16 lines · Jernej Škrabec
Quoted 16 lines
Quoted 10 lines
Quoted 7 lines

Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address 0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.

NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.

like in commit 0d17c865118881609ea7e381c7cadbb7979cc596 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")

Quoted 5 lines
Quoted 1 line

? ;-)

I was against that too.

It's time to be fixed in bootloader.

I agree, I was wondering about this shortcut as well... I'll implement some sort of generic reserved memory handling in U-Boot.

Signature · 1 line
Alexander Sverdlin.
#14 lore raw

PATCH v4 7/7 arm64: dts: allwinner: A133: add support for Baijie Helper A133 board

In reply to Alexander Sverdlin

Baijie Helper A133 board is a development board around Baijie A133 Core SBC. Features:

- 1/2/4GiB LPDDR4 DRAM
- 8/16/32GiB eMMC
- AXP707 PMIC
- USB-C OTG port in peripheral mode (via onboard hub)
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- Gigabit Ethernet
- Bluetooth
- WiFi

Add initial support for both the Helper and Core boards, including UART, PMU, eMMC, USB, Ethernet, LRADC-connected buttons.

UART1 can only be used for Bluetooth module, but BT-WiFi combo Allwinner AW869A chip has no mainline driver currently.

---
Changelog:
v4:
- renamed "sun50i-a133-baijie-helper.dtb" -> "sun50i-a133-helperboard.dtb"
- added "model" property into root of sun50i-a133-helperboard-core.dtsi
- added "cap-mmc-highspeed" and "max-frequency" into &mmc2
- added "x-powers,drive-vbus-en" and "*-supply" into &axp803
- dropped all "regulator-enable-ramp-delay" properties
- replaced &reg_dcdc3 with a "polyphased" comment
- exact DRAM voltage in &reg_dcdc5
- disabled &reg_dcdc6 to avoid "[ 31.710641] dcdc6: disabling"
- added &reg_vdd5v "root" regulator
- added "disable-wp" into &mmc0
- commented &usb_otg
- assigned usb1_vbus-supply in &usbphy
v3:
- added my copyrights into the newly introduced DTs
- all DT nodes sorted alphabetically
- all always-on regulators commented/propetly named
- all regulators got proper voltages (not default ranges)
- ADC-sensed buttons K1..K5 added
- re-labelled "eth_phy" -> "rgmii_phy"
- usbphy 0 switched from host into peripheral mode (downstream from an onboard hub)
- typo sun50i-a133-baije-core.dtsi -> sun50i-a133-baijie-core.dtsi v2:
- introduced baijie,helper-a133-core compatible for the Core (SoM) board

 arch/arm64/boot/dts/allwinner/Makefile        |   1 +
 .../sun50i-a133-helperboard-core.dtsi         | 197 ++++++++++++++++++
 .../dts/allwinner/sun50i-a133-helperboard.dts | 148 +++++++++++++
 3 files changed, 346 insertions(+)
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard-core.dtsi
 create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
index d116864b6c2b..cf8434064b0d 100644
@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a133-helperboard.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a133-liontron-h-a133l.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard-core.dtsi new file +197 -0

197 lines not on this page · raw message

arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard.dts new file +148 -0

148 lines not on this page · raw message

Signature · 1 line
2.54.0
maintainer Acked-by on v4 7/7
#15 lore raw

Re: [PATCH v4 7/7] arm64: dts: allwinner: A133: add support for Baijie Helper A133 board

Dne petek, 5. junij 2026 ob 09:09:21 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):

Quoted 13 lines

Baijie Helper A133 board is a development board around Baijie A133 Core SBC. Features:

- 1/2/4GiB LPDDR4 DRAM
- 8/16/32GiB eMMC
- AXP707 PMIC
- USB-C OTG port in peripheral mode (via onboard hub)
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- Gigabit Ethernet
- Bluetooth
- WiFi

Quoted 7 lines

Add initial support for both the Helper and Core boards, including UART, PMU, eMMC, USB, Ethernet, LRADC-connected buttons.

UART1 can only be used for Bluetooth module, but BT-WiFi combo Allwinner AW869A chip has no mainline driver currently.

Schema validation passes, so:

Best regards,
Jernej