Add support for Baijie Helper A133 board
Subsystems (5)
v4 cover Add support for Baijie Helper A133 board
Baijie Helper A133 board is a development board around Baijie A133 Core SBC. Features:
- 1/2/4GiB LPDDR4 DRAM
- 8/16/32GiB eMMC
- AXP707 PMIC
- USB-C OTG port in peripheral mode (via onboard hub)
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- Gigabit Ethernet
- Bluetooth
- WiFi
Add initial support for both the Helper and Core boards, including UART, PMU, eMMC, USB, Ethernet, LRADC-connected buttons.
UART1 can only be used for Bluetooth module, but BT-WiFi combo Allwinner AW869A chip has not mainline driver currently.
Changelog:
v4:
- reserve RAM for ATF
- sun4i-lradc-keys: Add A100/A133 compatible
- dt-bindings: renamed "Baijie Helper A133" -> "Baijie A133 HelperBoard"
- dt-bindings: renamed "baijie,helper-a133" -> "baijie,helperboard-a133"
- dt-bindings: introduced allwinner,sun50i-a100-lradc
- reserve RAM for ATF
- renamed "sun50i-a133-baijie-helper.dtb" -> "sun50i-a133-helperboard.dtb"
- added "model" property into root of sun50i-a133-helperboard-core.dtsi
- added "cap-mmc-highspeed" and "max-frequency" into &mmc2
- added "x-powers,drive-vbus-en" and "*-supply" into &axp803
- dropped all "regulator-enable-ramp-delay" properties
- replaced ®_dcdc3 with a "polyphased" comment
- exact DRAM voltage in ®_dcdc5
- disabled ®_dcdc6 to avoid "[ 31.710641] dcdc6: disabling"
- added ®_vdd5v "root" regulator
- added "disable-wp" into &mmc0
- commented &usb_otg
- assigned usb1_vbus-supply in &usbphy
v3:
- added lradc node to sun50i-a100.dtsi
- enabled LRADC driver in arm64 defconfig
- added my copyrights into the newly introduced DTs
- all DT nodes sorted alphabetically
- all always-on regulators commented/propetly named
- all regulators got proper voltages (not default ranges)
- ADC-sensed buttons K1..K5 added
- re-labelled "eth_phy" -> "rgmii_phy"
- usbphy 0 switched from host into peripheral mode (downstream from an onboard hub)
- typo sun50i-a133-baije-core.dtsi -> sun50i-a133-baijie-core.dtsi
- https://lore.kernel.org/all/[email protected]/
v2:
- introduced baijie,helper-a133-core compatible for the Core (SoM) board
- https://lore.kernel.org/all/[email protected]/
v1:
- https://lore.kernel.org/all/[email protected]/
Alexander Sverdlin (7):
arm64: defconfig: Enable Allwinner LRADC input driver
dt-bindings: vendor-prefixes: Add Shenzhen Baijie Technology Co., Ltd.
dt-bindings: arm: sunxi: Add Baijie HelperBoard A133 compatible
dt-bindings: input: sun4i-lradc-keys: Add A100/A133 compatible
arm64: dts: allwinner: a100: Add LRADC node
arm64: dts: allwinner: a100: reserve RAM for ATF
arm64: dts: allwinner: A133: add support for Baijie Helper A133 board
.../devicetree/bindings/arm/sunxi.yaml | 6 + .../input/allwinner,sun4i-a10-lradc-keys.yaml | 1 + .../devicetree/bindings/vendor-prefixes.yaml | 2 + arch/arm64/boot/dts/allwinner/Makefile | 1 + .../arm64/boot/dts/allwinner/sun50i-a100.dtsi | 25 +++ .../sun50i-a133-helperboard-core.dtsi | 197 ++++++++++++++++++ .../dts/allwinner/sun50i-a133-helperboard.dts | 148 +++++++++++++ arch/arm64/configs/defconfig | 1 + 8 files changed, 381 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard-core.dtsi create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard.dts
Signature · 1 line
2.54.0
PATCH v4 1/7 arm64: defconfig: Enable Allwinner LRADC input driver
Enable Allwinner LRADC input driver as module to support buttons on Baijie HelperBoard A133.
---
Changelog:
v4:
- no changes
v3:
- new patch
arch/arm64/configs/defconfig | 1 + 1 file changed, 1 insertion(+)
arch/arm64/configs/defconfig +1 -0
@@ -479,6 +479,7 @@ CONFIG_KEYBOARD_GPIO=y CONFIG_KEYBOARD_GPIO_POLLED=m CONFIG_KEYBOARD_SNVS_PWRKEY=m CONFIG_KEYBOARD_IMX_SC_KEY=m +CONFIG_KEYBOARD_SUN4I_LRADC=m CONFIG_KEYBOARD_CROS_EC=y CONFIG_KEYBOARD_MTK_PMIC=m CONFIG_MOUSE_ELAN_I2C=m
Signature · 1 line
2.54.0
Re: [PATCH v4 1/7] arm64: defconfig: Enable Allwinner LRADC input driver
Dne petek, 5. junij 2026 ob 09:09:15 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 4 lines
Enable Allwinner LRADC input driver as module to support buttons on Baijie HelperBoard A133.
Signed-off-by Alexander Sverdlin <[email protected]>
Best regards,
Jernej Skrabec
PATCH v4 2/7 dt-bindings: vendor-prefixes: Add Shenzhen Baijie Technology Co., Ltd.
In reply to Alexander SverdlinShenzhen Baijie Technology Co., Ltd. focuses on R&D and production of embedded products as well as customization of embedded solutions.
--- Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++ 1 file changed, 2 insertions(+)
Documentation/devicetree/bindings/vendor-prefixes.yaml +2 -0
@@ -229,6 +229,8 @@ patternProperties: description: Azoteq (Pty) Ltd "^azw,.*": description: Shenzhen AZW Technology Co., Ltd. + "^baijie,.*": + description: Shenzhen Baijie Technology Co., Ltd. "^baikal,.*": description: BAIKAL ELECTRONICS, JSC "^bananapi,.*":
Signature · 1 line
2.54.0
PATCH v4 3/7 dt-bindings: arm: sunxi: Add Baijie HelperBoard A133 compatible
In reply to Alexander SverdlinBaijie HelperBoard A133 is a development board around their A133 Core board. Introduce a compatible for both the Core and the development boards.
---
Changelog:
v4:
- renamed "Baijie Helper A133" -> "Baijie A133 HelperBoard"
- renamed "baijie,helper-a133" -> "baijie,helperboard-a133" v3:
- no separate section for "core" .dtsi
v2:
- introduced baijie,helper-a133-core compatible for the Core (SoM) board
Documentation/devicetree/bindings/arm/sunxi.yaml | 6 ++++++ 1 file changed, 6 insertions(+)
Documentation/devicetree/bindings/arm/sunxi.yaml +6 -0
@@ -96,6 +96,12 @@ properties: - const: allwinner,ba10-tvbox - const: allwinner,sun4i-a10 + - description: Baijie A133 HelperBoard + items: + - const: baijie,helperboard-a133 + - const: baijie,helperboard-a133-core + - const: allwinner,sun50i-a100 + - description: BananaPi items: - const: lemaker,bananapi
Signature · 1 line
2.54.0
PATCH v4 4/7 dt-bindings: input: sun4i-lradc-keys: Add A100/A133 compatible
In reply to Alexander SverdlinThe Allwinner A100/A133 SoCs have an LRADC which is compatible with the versions in existing SoCs. Add a compatible string for A100, with the R329 fallback.
---
Changelog:
v4:
- new patch
.../bindings/input/allwinner,sun4i-a10-lradc-keys.yaml | 1 + 1 file changed, 1 insertion(+)
Documentation/devicetree/bindings/input/allwinner,sun4i-a10-lradc-keys.yaml +1 -0
@@ -23,6 +23,7 @@ properties: - const: allwinner,sun50i-r329-lradc - items: - enum: + - allwinner,sun50i-a100-lradc - allwinner,sun50i-h616-lradc - allwinner,sun20i-d1-lradc - const: allwinner,sun50i-r329-lradc
Signature · 1 line
2.54.0
Re: [PATCH v4 4/7] dt-bindings: input: sun4i-lradc-keys: Add A100/A133 compatible
pw-bot: not-applicable
PATCH v4 5/7 arm64: dts: allwinner: a100: Add LRADC node
In reply to Alexander SverdlinA100/A133 SoCs feature a Low Rate ADC (LRADC) for Key application.
Specs:
- Power supply voltage: 1.8 V
- Reference voltage: 1.35 V
- Interrupt support
- Support Hold Key and General Key
- Support normal, continue and single work mode
- 6-bits resolution, sample rate up to 2 kHz
- Voltage input range between 0 and 1.35 V
---
Changelog:
v4:
- added allwinner,sun50i-a100-lradc compatible
v3:
- new patch
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +9 -0
@@ -466,6 +466,15 @@ ths: thermal-sensor@5070400 { #thermal-sensor-cells = <1>; }; + lradc: lradc@5070800 { + compatible = "allwinner,sun50i-a100-lradc", "allwinner,sun50i-r329-lradc"; + reg = <0x05070800 0x400>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_LRADC>; + resets = <&ccu RST_BUS_LRADC>; + status = "disabled"; + }; + usb_otg: usb@5100000 { compatible = "allwinner,sun50i-a100-musb", "allwinner,sun8i-a33-musb";
Signature · 1 line
2.54.0
Re: [PATCH v4 5/7] arm64: dts: allwinner: a100: Add LRADC node
Dne petek, 5. junij 2026 ob 09:09:19 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 27 lines
A100/A133 SoCs feature a Low Rate ADC (LRADC) for Key application.
Specs:
- Power supply voltage: 1.8 V
- Reference voltage: 1.35 V
- Interrupt support
- Support Hold Key and General Key
- Support normal, continue and single work mode
- 6-bits resolution, sample rate up to 2 kHz
- Voltage input range between 0 and 1.35 VSigned-off-by Alexander Sverdlin <[email protected]>---
Changelog:
v4:
- added allwinner,sun50i-a100-lradc compatible
v3:
- new patcharch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +0
-0
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi ths: thermal-sensor@5070400 { · line 470
Quoted 5 lines
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +2
-0@@ -466,6 +466,15 @@ ths: thermal-sensor@5070400 { #thermal-sensor-cells = <1>; }; + lradc: lradc@5070800 { + compatible = "allwinner,sun50i-a100-lradc", "allwinner,sun50i-r329-lradc";
Break this into two lines, like usb_otg below. With that:
Best regards,
Jernej Skrabec
Quoted 11 lines
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +7
-0+ reg = <0x05070800 0x400>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_LRADC>; + resets = <&ccu RST_BUS_LRADC>; + status = "disabled"; + }; + usb_otg: usb@5100000 { compatible = "allwinner,sun50i-a100-musb", "allwinner,sun8i-a33-musb";
PATCH v4 6/7 arm64: dts: allwinner: a100: reserve RAM for ATF
In reply to Alexander SverdlinAdd reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address 0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.
---
Changelog:
v4:
- new patch
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16 -0
@@ -87,6 +87,22 @@ osc32k: osc32k-clk { #clock-cells = <0>; }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * 256 KiB reserved for Trusted Firmware-A (BL31). + * This is added by BL31 itself, but some bootloaders fail + * to propagate this into the DTB handed to kernels. + */ + secmon@40000000 { + reg = <0x0 0x40000000 0x0 0x40000>; + no-map; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 13
Signature · 1 line
2.54.0
Jernej Škrabec
maintainerRe: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF
Dne petek, 5. junij 2026 ob 09:09:20 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 7 lines
Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address
0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.Signed-off-by Alexander Sverdlin <[email protected]>
NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.
Best regards,
Jernej Skrabec
Quoted 36 lines
---
Changelog:
v4:
- new patcharch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16
-0@@ -87,6 +87,22 @@ osc32k: osc32k-clk { #clock-cells = <0>; }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * 256 KiB reserved for Trusted Firmware-A (BL31). + * This is added by BL31 itself, but some bootloaders fail + * to propagate this into the DTB handed to kernels. + */ + secmon@40000000 { + reg = <0x0 0x40000000 0x0 0x40000>; + no-map; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 13
Re: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF
Hi Jernej,
Quoted 11 lines · Jernej Škrabec
Dne petek, 5. junij 2026 ob 09:09:20 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 7 lines
Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address
0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.Signed-off-by Alexander Sverdlin <[email protected]>NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.
like in commit 0d17c865118881609ea7e381c7cadbb7979cc596 ("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")
? ;-)
Quoted 38 lines
Best regards,
Jernej SkrabecQuoted 35 lines
---
Changelog:
v4:
- new patch
arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi| 16 ++++++++++++++++1 file changed, 16 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +0
-0@@ -87,6 +87,22 @@ osc32k: osc32k-clk { #clock-cells = <0>; };arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16
-0+ reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * 256 KiB reserved for Trusted Firmware-A (BL31). + * This is added by BL31 itself, but some bootloaders fail + * to propagate this into the DTB handed to kernels. + */ + secmon@40000000 { + reg = <0x0 0x40000000 0x0 0x40000>; + no-map; + }; + }; +timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI13
Signature · 1 line
Alexander Sverdlin.
Jernej Škrabec
maintainerRe: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF
Dne sobota, 13. junij 2026 ob 10:34:42 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 16 lines
Hi Jernej,
Quoted 11 lines · Jernej Škrabec
Dne petek, 5. junij 2026 ob 09:09:20 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 7 lines
Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address
0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.Signed-off-by Alexander Sverdlin <[email protected]>NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.
Quoted 5 lines
like in commit
0d17c865118881609ea7e381c7cadbb7979cc596("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")Signed-off-by Jernej Skrabec <[email protected]>? ;-)
I was against that too.
It's time to be fixed in bootloader.
Best regards,
Jernej
Quoted 41 lines
Quoted 39 lines
Best regards,
Jernej SkrabecQuoted 35 lines
---
Changelog:
v4:
- new patcharch/arm64/boot/dts/allwinner/sun50i-a100.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+)arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi +16
-0@@ -87,6 +87,22 @@ osc32k: osc32k-clk { #clock-cells = <0>; }; + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + /* + * 256 KiB reserved for Trusted Firmware-A (BL31). + * This is added by BL31 itself, but some bootloaders fail + * to propagate this into the DTB handed to kernels. + */ + secmon@40000000 { + reg = <0x0 0x40000000 0x0 0x40000>; + no-map; + }; + }; + timer { compatible = "arm,armv8-timer"; interrupts = <GIC_PPI 13
Re: [PATCH v4 6/7] arm64: dts: allwinner: a100: reserve RAM for ATF
Hi Jernej,
Quoted 16 lines · Jernej Škrabec
Quoted 16 lines
Quoted 10 lines
Quoted 7 lines
Add reserved-memory node carving out Trusted Firmware-A region spanning fixed 256K from physical address
0x40000000. Even though Allwinner ATF itself passes the address range in the fdt to U-Boot, U-Boot currently only reserves this memory internally, but doesn't carve out the region in the fdt passed to Linux.Signed-off-by Alexander Sverdlin <[email protected]>NAK. It is job of boot procedure to properly inject TF-A reserved node. Any issue should be fixed there.
like in commit
0d17c865118881609ea7e381c7cadbb7979cc596("arm64: dts: allwinner: Add Allwinner H616 .dtsi file")Signed-off-by Jernej Skrabec <[email protected]>
Quoted 5 lines
Quoted 1 line
? ;-)
I was against that too.
It's time to be fixed in bootloader.
I agree, I was wondering about this shortcut as well... I'll implement some sort of generic reserved memory handling in U-Boot.
Signature · 1 line
Alexander Sverdlin.
PATCH v4 7/7 arm64: dts: allwinner: A133: add support for Baijie Helper A133 board
In reply to Alexander SverdlinBaijie Helper A133 board is a development board around Baijie A133 Core SBC. Features:
- 1/2/4GiB LPDDR4 DRAM
- 8/16/32GiB eMMC
- AXP707 PMIC
- USB-C OTG port in peripheral mode (via onboard hub)
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- Gigabit Ethernet
- Bluetooth
- WiFi
Add initial support for both the Helper and Core boards, including UART, PMU, eMMC, USB, Ethernet, LRADC-connected buttons.
UART1 can only be used for Bluetooth module, but BT-WiFi combo Allwinner AW869A chip has no mainline driver currently.
---
Changelog:
v4:
- renamed "sun50i-a133-baijie-helper.dtb" -> "sun50i-a133-helperboard.dtb"
- added "model" property into root of sun50i-a133-helperboard-core.dtsi
- added "cap-mmc-highspeed" and "max-frequency" into &mmc2
- added "x-powers,drive-vbus-en" and "*-supply" into &axp803
- dropped all "regulator-enable-ramp-delay" properties
- replaced ®_dcdc3 with a "polyphased" comment
- exact DRAM voltage in ®_dcdc5
- disabled ®_dcdc6 to avoid "[ 31.710641] dcdc6: disabling"
- added ®_vdd5v "root" regulator
- added "disable-wp" into &mmc0
- commented &usb_otg
- assigned usb1_vbus-supply in &usbphy
v3:
- added my copyrights into the newly introduced DTs
- all DT nodes sorted alphabetically
- all always-on regulators commented/propetly named
- all regulators got proper voltages (not default ranges)
- ADC-sensed buttons K1..K5 added
- re-labelled "eth_phy" -> "rgmii_phy"
- usbphy 0 switched from host into peripheral mode (downstream from an onboard hub)
- typo sun50i-a133-baije-core.dtsi -> sun50i-a133-baijie-core.dtsi v2:
- introduced baijie,helper-a133-core compatible for the Core (SoM) board
arch/arm64/boot/dts/allwinner/Makefile | 1 + .../sun50i-a133-helperboard-core.dtsi | 197 ++++++++++++++++++ .../dts/allwinner/sun50i-a133-helperboard.dts | 148 +++++++++++++ 3 files changed, 346 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard-core.dtsi create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard.dts
arch/arm64/boot/dts/allwinner/Makefile +1 -0
@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-sopine-baseboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-teres-i.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h64-remix-mini-pc.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a100-allwinner-perf1.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a133-helperboard.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a133-liontron-h-a133l.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-bananapi-m2-plus-v1.2.dtb
arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard-core.dtsi new file +197 -0
197 lines not on this page · raw message
arch/arm64/boot/dts/allwinner/sun50i-a133-helperboard.dts new file +148 -0
148 lines not on this page · raw message
Signature · 1 line
2.54.0
Re: [PATCH v4 7/7] arm64: dts: allwinner: A133: add support for Baijie Helper A133 board
Dne petek, 5. junij 2026 ob 09:09:21 Srednjeevropski poletni čas je Alexander Sverdlin napisal(a):
Quoted 13 lines
Baijie Helper A133 board is a development board around Baijie A133 Core SBC. Features:
- 1/2/4GiB LPDDR4 DRAM
- 8/16/32GiB eMMC
- AXP707 PMIC
- USB-C OTG port in peripheral mode (via onboard hub)
- 2 USB 2.0 ports
- MicroSD slot and on-board eMMC module
- Gigabit Ethernet
- Bluetooth
- WiFi
Quoted 7 lines
Add initial support for both the Helper and Core boards, including UART, PMU, eMMC, USB, Ethernet, LRADC-connected buttons.
UART1 can only be used for Bluetooth module, but BT-WiFi combo Allwinner AW869A chip has no mainline driver currently.
Signed-off-by Alexander Sverdlin <[email protected]>
Schema validation passes, so:
Best regards,
Jernej