Add DFU and usb boot for TI am62x
Subsystems (3)
v3 cover Add DFU and usb boot for TI am62x
Previous version of this patchset went out back in April and got delayed for various reasons. As some parts were merge this is a somewhat smaller set then before.
Patches against u-boot/next to take advantage of the latest dts sync from linux v6.7-rc1
0: https://lists.denx.de/pipermail/u-boot/2023-April/514642.html
Changes in v3:
- Add dfu via environment rather then config headers
- Enable usb nodes in all boot phases
- Run savedefconfig to adjust to more recent u-boot
Changes in v2:
- Switch dwc3 glue to a seperate driver rather then in dwc-generic
- Minimize config changes to just DFU configuration
- Only enable usb port 0 DFU in SPL
- Create a seperate defconfig for R5
Sjoerd Simons (4):
usb: dwc3: Add dwc3 glue driver for am62
board: ti: am62x: am62x: include env for DFU
arm: dts: k3-am625-sk: Enable usb ports in u-boot
configs: am62x_evm_*: Enable USB and DFU support
arch/arm/dts/k3-am625-sk-u-boot.dtsi | 9 ++ board/ti/am62x/am62x.env | 1 + configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111 +++++++++++++++++++++++ drivers/usb/dwc3/Kconfig | 14 +++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-am62.c | 125 ++++++++++++++++++++++++++ 7 files changed, 291 insertions(+), 1 deletion(-) create mode 100644 configs/am62x_evm_r5_usbdfu_defconfig create mode 100644 drivers/usb/dwc3/dwc3-am62.c
Signature · 1 line
2.43.0
PATCH v3 1/4 usb: dwc3: Add dwc3 glue driver for am62
Add glue code for TI AM62 to the dwc3 driver; Most code adopted from TI vendor u-boot code.
---
(no changes since v2)
Changes in v2:
- Switch dwc3 glue to a seperate driver rather then in dwc-generic
drivers/usb/dwc3/Kconfig | 14 ++++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-am62.c | 125 +++++++++++++++++++++++++++++++++++ 3 files changed, 140 insertions(+) create mode 100644 drivers/usb/dwc3/dwc3-am62.c
drivers/usb/dwc3/Kconfig +14 -0
@@ -37,6 +37,20 @@ config SPL_USB_DWC3_GENERIC Select this for Xilinx ZynqMP and similar Platforms. This wrapper supports Host and Peripheral operation modes. +config SPL_USB_DWC3_AM62 + bool "TI AM62 USB wrapper" + depends on SPL_DM_USB && SPL_USB_DWC3_GENERIC + help + Select this for TI AM62 Platforms. + This wrapper supports Host and Peripheral operation modes. + +config USB_DWC3_AM62 + bool "TI AM62 USB wrapper" + depends on DM_USB && USB_DWC3_GENERIC + help + Select this for TI AM62 Platforms. + This wrapper supports Host and Peripheral operation modes. + config USB_DWC3_MESON_G12A bool "Amlogic Meson G12A USB wrapper" depends on DM_USB && USB_DWC3 && ARCH_MESON
drivers/usb/dwc3/Makefile +1 -0
@@ -6,6 +6,7 @@ dwc3-y := core.o obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o +obj-$(CONFIG_$(SPL_)USB_DWC3_AM62) += dwc3-am62.o obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o obj-$(CONFIG_USB_DWC3_MESON_GXL) += dwc3-meson-gxl.o
drivers/usb/dwc3/dwc3-am62.c new file +125 -0
125 lines not on this page · raw message
Signature · 1 line
2.43.0
Re: [PATCH v3 1/4] usb: dwc3: Add dwc3 glue driver for am62
Hi Sjoerd,
Quoted 89 lines · Sjoerd Simons
Add glue code for TI AM62 to the dwc3 driver; Most code adopted from TI vendor u-boot code.
Signed-off-by Sjoerd Simons <[email protected]>Reviewed-by Mattijs Korpershoek <[email protected]>---
(no changes since v2)
Changes in v2:
- Switch dwc3 glue to a seperate driver rather then in dwc-genericdrivers/usb/dwc3/Kconfig | 14 ++++ drivers/usb/dwc3/Makefile | 1 + drivers/usb/dwc3/dwc3-am62.c | 125 +++++++++++++++++++++++++++++++++++ 3 files changed, 140 insertions(+) create mode 100644 drivers/usb/dwc3/dwc3-am62.cdrivers/usb/dwc3/Kconfig +14
-0@@ -37,6 +37,20 @@ config SPL_USB_DWC3_GENERIC Select this for Xilinx ZynqMP and similar Platforms. This wrapper supports Host and Peripheral operation modes. +config SPL_USB_DWC3_AM62 + bool "TI AM62 USB wrapper" + depends on SPL_DM_USB && SPL_USB_DWC3_GENERIC + help + Select this for TI AM62 Platforms. + This wrapper supports Host and Peripheral operation modes. + +config USB_DWC3_AM62 + bool "TI AM62 USB wrapper" + depends on DM_USB && USB_DWC3_GENERIC + help + Select this for TI AM62 Platforms. + This wrapper supports Host and Peripheral operation modes. + config USB_DWC3_MESON_G12A bool "Amlogic Meson G12A USB wrapper" depends on DM_USB && USB_DWC3 && ARCH_MESONdrivers/usb/dwc3/Makefile +1
-0@@ -6,6 +6,7 @@ dwc3-y := core.o obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o +obj-$(CONFIG_$(SPL_)USB_DWC3_AM62) += dwc3-am62.o obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o obj-$(CONFIG_USB_DWC3_MESON_GXL) += dwc3-meson-gxl.odrivers/usb/dwc3/dwc3-am62.c new file +27
-0@@ -0,0 +1,125 @@ +// SPDX-License-Identifier: GPL-2.0 +/* +* TI AM62 specific glue layer for DWC3 +*/ + +#include <dm.h> +#include <dm/device_compat.h> +#include <regmap.h> +#include <syscon.h> +#include <asm/io.h> + +#include "dwc3-generic.h" + +static void dwc3_ti_am62_glue_configure (struct udevice *dev,int index, +enum usb_dr_mode mode) +{ +#define USBSS_MODE_CONTROL 0x1c +#define USBSS_PHY_CONFIG 0x8 +#define USBSS_PHY_VBUS_SEL_MASK GENMASK(2, 1) +#define USBSS_PHY_VBUS_SEL_SHIFT 1 +#define USBSS_MODE_VALID BIT(0) +#define PHY_PLL_REFCLK_MASK GENMASK(3, 0) +static const int dwc3_ti_am62_rate_table[] = {/* in KHZ */ +9600 , +10000 , +12000 , +19200 ,
drivers/usb/dwc3/dwc3-am62.c line 37
Quoted 10 lines
drivers/usb/dwc3/dwc3-am62.c new file +10
-0+20000 , +24000 , +25000 , +26000 , +38400 , +40000 , +58000 , +50000 , + 52000, +};
Can we please move these defines and dwc3_ti_am62_rate_table outside the function?
Quoted 88 lines
drivers/usb/dwc3/dwc3-am62.c new file +88
-0+ +struct clk usb2_refclk; +int rate_code, i, ret; +unsigned long rate; +u32 reg; +void *usbss; +bool vbus_divider; +struct regmap *syscon; +struct ofnode_phandle_args args; + + usbss =dev_remap_addr_index (dev,0 ); +if (IS_ERR (usbss)) { +dev_err (dev,"can't map IOMEM resource\n" ); +return ; + } + + ret =clk_get_by_name (dev,"ref" , &usb2_refclk); +if (ret) { +dev_err (dev,"can't get usb2_refclk\n" ); +return ; + } + +/* Calculate the rate code */ + rate =clk_get_rate (&usb2_refclk); + rate /=1000 ;/* To KHz */ +for (i =0 ; i <ARRAY_SIZE (dwc3_ti_am62_rate_table); i++) { +if (dwc3_ti_am62_rate_table[i] == rate) +break ; + } + +if (i ==ARRAY_SIZE (dwc3_ti_am62_rate_table)) { +dev_err (dev,"unsupported usb2_refclk rate: %lu KHz\n" , rate); +return ; + } + + rate_code = i; + +/* Read the syscon property */ + syscon =syscon_regmap_lookup_by_phandle (dev,"ti,syscon-phy-pll-refclk" ); +if (IS_ERR (syscon)) { +dev_err (dev,"unable to get ti,syscon-phy-pll-refclk regmap\n" ); +return ; + } + + ret =ofnode_parse_phandle_with_args (dev_ofnode (dev),"ti,syscon-phy-pll-refclk" ,NULL ,1 , +0 , &args); +if (ret) +return ; + +/* Program PHY PLL refclk by reading syscon property */ + ret =regmap_update_bits (syscon, args.args[0 ],PHY_PLL_REFCLK_MASK , rate_code); +if (ret) { +dev_err (dev,"failed to set phy pll reference clock rate\n" ); +return ; + } + +/* VBUS divider select */ + reg =readl (usbss +USBSS_PHY_CONFIG ); + vbus_divider =dev_read_bool (dev,"ti,vbus-divider" ); +if (vbus_divider) + reg |=1 <<USBSS_PHY_VBUS_SEL_SHIFT ; + +writel (reg, usbss +USBSS_PHY_CONFIG ); + +/* Set mode valid */ + reg =readl (usbss +USBSS_MODE_CONTROL ); + reg |=USBSS_MODE_VALID ; +writel (reg, usbss +USBSS_MODE_CONTROL ); +} + +struct dwc3_glue_ops ti_am62_ops = { + .glue_configure = dwc3_ti_am62_glue_configure, +}; + +static const struct udevice_id dwc3_am62_match[] = { + { .compatible ="ti,am62-usb" , .data = (ulong)&ti_am62_ops }, + {/* sentinel */ } +}; + +U_BOOT_DRIVER (dwc3_am62_wrapper) = { + .name ="dwc3-am62" , + .id =UCLASS_SIMPLE_BUS , + .of_match = dwc3_am62_match, + .bind = dwc3_glue_bind, + .probe = dwc3_glue_probe, + .remove = dwc3_glue_remove, + .plat_auto =sizeof (struct dwc3_glue_data ), +};
Signature · 2 lines
cheers, -roger
PATCH v3 2/4 board: ti: am62x: am62x: include env for DFU
In reply to Sjoerd SimonsInclude standard TI K3 dfu environment
---
Changes in v3:
- Add dfu via environment rather then config headers
Changes in v2:
- Minimize config changes to just DFU configuration
board/ti/am62x/am62x.env | 1 + 1 file changed, 1 insertion(+)
board/ti/am62x/am62x.env +1 -0
@@ -1,6 +1,7 @@ #include <env/ti/ti_common.env> #include <env/ti/default_findfdt.env> #include <env/ti/mmc.env> +#include <env/ti/k3_dfu.env> name_kern=Image console=ttyS2,115200n8
Signature · 1 line
2.43.0
PATCH v3 3/4 arm: dts: k3-am625-sk: Enable usb ports in u-boot
In reply to Sjoerd SimonsEnable both usb0 as a peripheral for use with DFU and
---
Changes in v3:
- Enable usb nodes in all boot phases
Changes in v2:
- Only enable usb port 0 DFU in SPL
arch/arm/dts/k3-am625-sk-u-boot.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)
arch/arm/dts/k3-am625-sk-u-boot.dtsi +9 -0
@@ -46,3 +46,12 @@ &cpsw_port2 { status = "disabled"; }; + +&usbss0 { + bootph-all; +}; + +&usb0 { + dr_mode = "peripheral"; + bootph-all; +};
Signature · 1 line
2.43.0
Re: [PATCH v3 3/4] arm: dts: k3-am625-sk: Enable usb ports in u-boot
Quoted 20 lines · Sjoerd Simons
Enable both usb0 as a peripheral for use with DFU and
Signed-off-by Sjoerd Simons <[email protected]>---
Changes in v3:
- Enable usb nodes in all boot phasesChanges in v2:
- Only enable usb port 0 DFU in SPLarch/arm/dts/k3-am625-sk-u-boot.dtsi | 9 +++++++++ 1 file changed, 9 insertions(+)arch/arm/dts/k3-am625-sk-u-boot.dtsi +0
-0
arch/arm/dts/k3-am625-sk-u-boot.dtsi line 55
Quoted 10 lines
arch/arm/dts/k3-am625-sk-u-boot.dtsi +7
-0@@ -46,3 +46,12 @@ &cpsw_port2 { status = "disabled"; }; + +&usbss0 { + bootph-all; +}; + +&usb0 { + dr_mode = "peripheral";
There was a series [1] just to undo this.
Can we make it auto-magically work even when mode is "otg" Can we address anything missing at the driver level?
arch/arm/dts/k3-am625-sk-u-boot.dtsi line 57
Quoted 2 lines
arch/arm/dts/k3-am625-sk-u-boot.dtsi +2
-0+ bootph-all; +};
[1] https://lore.kernel.org/all/[email protected]/
Signature · 2 lines
cheers, -roger
PATCH v3 4/4 configs: am62x_evm_*: Enable USB and DFU support
In reply to Sjoerd SimonsEnable USB host as well as USB gadget and DFU support for a53; For the r5 due to the smaller available size create a new config just for DFU support
---
Changes in v3:
- Run savedefconfig to adjust to more recent u-boot
Changes in v2:
- Create a seperate defconfig for R5
configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111 ++++++++++++++++++++++++++ 2 files changed, 141 insertions(+), 1 deletion(-) create mode 100644 configs/am62x_evm_r5_usbdfu_defconfig
configs/am62x_evm_a53_defconfig +30 -1
@@ -1,5 +1,6 @@ CONFIG_ARM=y CONFIG_ARCH_K3=y +CONFIG_SYS_MALLOC_LEN=0x2000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y
@@ -40,17 +41,23 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_STACK_R=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400 +CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img" CONFIG_SPL_DM_MAILBOX=y CONFIG_SPL_DM_SPI_FLASH=y CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y # CONFIG_SPL_SPI_FLASH_TINY is not set CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000 +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_DFU=y CONFIG_SPL_YMODEM_SUPPORT=y -CONFIG_SYS_BOOTM_LEN=0x800000 +CONFIG_CMD_DFU=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y CONFIG_MULTI_DTB_FIT=y
@@ -61,10 +68,17 @@ CONFIG_SPL_DM=y CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_REGMAP=y CONFIG_SPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y CONFIG_SPL_OF_TRANSLATE=y CONFIG_CLK=y CONFIG_SPL_CLK=y CONFIG_CLK_TI_SCI=y +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_SYS_DFU_DATA_BUF_SIZE=0x5000 +CONFIG_SYS_DFU_MAX_FILE_SIZE=0x800000 CONFIG_DMA_CHANNELS=y CONFIG_TI_K3_NAVSS_UDMA=y CONFIG_TI_SCI_PROTOCOL=y
@@ -103,4 +117,19 @@ CONFIG_CADENCE_QSPI=y CONFIG_SYSRESET=y CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_TI_SCI=y +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_SPL_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_SPL_USB_DWC3_GENERIC=y +CONFIG_SPL_USB_DWC3_AM62=y +CONFIG_USB_DWC3_AM62=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" +CONFIG_USB_GADGET_VENDOR_NUM=0x0451 +CONFIG_USB_GADGET_PRODUCT_NUM=0x6165 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_FS_FAT_MAX_CLUSTSIZE=16384
configs/am62x_evm_r5_usbdfu_defconfig new file +111 -0
111 lines not on this page · raw message
Signature · 1 line
2.43.0
Re: [PATCH v3 4/4] configs: am62x_evm_*: Enable USB and DFU support
Hi Sjoerd!
On December 12, 2023 thus sayeth Sjoerd Simons:
Quoted 8 lines
Enable USB host as well as USB gadget and DFU support for a53; For the r5 due to the smaller available size create a new config just for DFU support
Signed-off-by Sjoerd Simons <[email protected]>---
Quoted 8 lines
Changes in v3:
- Run savedefconfig to adjust to more recent u-bootChanges in v2:
- Create a seperate defconfig for R5configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111 ++++++++++++++++++++++++++
One of the newer developments was the addition of config fragments[0] to try to minimize all the duplicate defconfigs for all the different evaluation boards for the same SoC we have in the pipeline. I'm wondering what people would think if we did this for the different boot-mode defconfigs for the 62xx extended family like this usbdfu and cpsw?
idk how messy it would get trying to disable one of the primary boot modes like MMC and enable USB though... So this may be a idea for another day.
[0] https://lore.kernel.org/u-boot/[email protected]/
~Bryan
Re: [PATCH v3 4/4] configs: am62x_evm_*: Enable USB and DFU support
Hey Brian,
On Tue, 2023-12-12 at 21:58 -0600, Bryan Brattlof wrote:
[...]
Quoted 14 lines
Quoted 4 lines
configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111
++++++++++++++++++++++++++One of the newer developments was the addition of config fragments[0] to
try to minimize all the duplicate defconfigs for all the different evaluation boards for the same SoC we have in the pipeline. I'm wondering what people would think if we did this for the different boot-mode defconfigs for the 62xx extended family like this usbdfu and
cpsw?
Quoted 3 lines
idk how messy it would get trying to disable one of the primary boot modes like MMC and enable USB though... So this may be a idea for another day.
Nishanth mentioned the same and it's something i'd like to play with (a beagleplay is on the way, but stuck in customs atm for some practical tests).
However I think it would make sense to get this landed first and then try refactoring with config fragments for a second step?
Quoted 6 lines
[0]
https://lore.kernel.org/u-boot/[email protected]/~Bryan
Signature · 2 lines
Sjoerd Simons Collabora Ltd.
Re: [PATCH v3 4/4] configs: am62x_evm_*: Enable USB and DFU support
On December 13, 2023 thus sayeth Sjoerd Simons:
Quoted 18 lines
Hey Brian,
On Tue, 2023-12-12 at 21:58 -0600, Bryan Brattlof wrote:
[...]Quoted 14 lines
Quoted 4 lines
configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111
++++++++++++++++++++++++++One of the newer developments was the addition of config fragments[0] to
try to minimize all the duplicate defconfigs for all the different evaluation boards for the same SoC we have in the pipeline. I'm wondering what people would think if we did this for the different boot-mode defconfigs for the 62xx extended family like this usbdfu and
cpsw?
Quoted 5 lines
Quoted 3 lines
idk how messy it would get trying to disable one of the primary boot modes like MMC and enable USB though... So this may be a idea for another day.
Nishanth mentioned the same and it's something i'd like to play with
Ah Ok! As long as you saw it :)
Quoted 3 lines
(a beagleplay is on the way, but stuck in customs atm for some practical tests).
Nice! It's a fun little board
Quoted 3 lines
However I think it would make sense to get this landed first and then try refactoring with config fragments for a second step?
I agree. It's on my TODO list to try to clean up some of the messes we've made so I thought I chime in
Don't let me stop you from adding features
~Bryan
Re: [PATCH v3 4/4] configs: am62x_evm_*: Enable USB and DFU support
Quoted 33 lines · Bryan Brattlof
On December 13, 2023 thus sayeth Sjoerd Simons:
Quoted 18 lines
Hey Brian,
On Tue, 2023-12-12 at 21:58 -0600, Bryan Brattlof wrote:
[...]Quoted 14 lines
Quoted 4 lines
configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111
++++++++++++++++++++++++++One of the newer developments was the addition of config fragments[0] to
try to minimize all the duplicate defconfigs for all the different evaluation boards for the same SoC we have in the pipeline. I'm wondering what people would think if we did this for the different boot-mode defconfigs for the 62xx extended family like this usbdfu and
cpsw?Quoted 5 lines
Quoted 3 lines
idk how messy it would get trying to disable one of the primary boot modes like MMC and enable USB though... So this may be a idea for another day.
Nishanth mentioned the same and it's something i'd like to play with
Ah Ok! As long as you saw it :)
Quoted 3 lines
(a beagleplay is on the way, but stuck in customs atm for some practical tests).
Nice! It's a fun little board
Quoted 8 lines
Quoted 3 lines
However I think it would make sense to get this landed first and then try refactoring with config fragments for a second step?
I agree. It's on my TODO list to try to clean up some of the messes we've made so I thought I chime in
Don't let me stop you from adding features
I prefer we do the fragments with this series. We can validate and update the fragment if required with follow on. but rather not keep churning the usage model.
Also missing is documentation update on how to build/use dfu mode.
Signature · 3 lines
Regards, Nishanth Menon Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
Re: [PATCH v3 4/4] configs: am62x_evm_*: Enable USB and DFU support
In reply to Sjoerd SimonsQuoted 187 lines · Sjoerd Simons
Enable USB host as well as USB gadget and DFU support for a53; For the r5 due to the smaller available size create a new config just for DFU support
Signed-off-by Sjoerd Simons <[email protected]>---
Changes in v3:
- Run savedefconfig to adjust to more recent u-bootChanges in v2:
- Create a seperate defconfig for R5configs/am62x_evm_a53_defconfig | 31 ++++++- configs/am62x_evm_r5_usbdfu_defconfig | 111 ++++++++++++++++++++++++++ 2 files changed, 141 insertions(+), 1 deletion(-) create mode 100644 configs/am62x_evm_r5_usbdfu_defconfigconfigs/am62x_evm_a53_defconfig +30
-1@@ -1,5 +1,6 @@ CONFIG_ARM=y CONFIG_ARCH_K3=y +CONFIG_SYS_MALLOC_LEN=0x2000000 CONFIG_SYS_MALLOC_F_LEN=0x8000 CONFIG_SPL_LIBCOMMON_SUPPORT=y CONFIG_SPL_LIBGENERIC_SUPPORT=y@@ -40,17 +41,23 @@ CONFIG_SPL_SYS_MALLOC_SIMPLE=y CONFIG_SPL_STACK_R=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x1400 +CONFIG_SPL_ENV_SUPPORT=y CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img" CONFIG_SPL_DM_MAILBOX=y CONFIG_SPL_DM_SPI_FLASH=y CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y # CONFIG_SPL_SPI_FLASH_TINY is not set CONFIG_SPL_SPI_FLASH_SFDP_SUPPORT=y CONFIG_SPL_SPI_LOAD=y CONFIG_SYS_SPI_U_BOOT_OFFS=0x280000 +CONFIG_SPL_USB_GADGET=y +CONFIG_SPL_DFU=y CONFIG_SPL_YMODEM_SUPPORT=y -CONFIG_SYS_BOOTM_LEN=0x800000 +CONFIG_CMD_DFU=y CONFIG_CMD_MMC=y +CONFIG_CMD_USB=y CONFIG_OF_CONTROL=y CONFIG_SPL_OF_CONTROL=y CONFIG_MULTI_DTB_FIT=y@@ -61,10 +68,17 @@ CONFIG_SPL_DM=y CONFIG_SPL_DM_SEQ_ALIAS=y CONFIG_REGMAP=y CONFIG_SPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y CONFIG_SPL_OF_TRANSLATE=y CONFIG_CLK=y CONFIG_SPL_CLK=y CONFIG_CLK_TI_SCI=y +CONFIG_DFU_MMC=y +CONFIG_DFU_RAM=y +CONFIG_DFU_SF=y +CONFIG_SYS_DFU_DATA_BUF_SIZE=0x5000 +CONFIG_SYS_DFU_MAX_FILE_SIZE=0x800000 CONFIG_DMA_CHANNELS=y CONFIG_TI_K3_NAVSS_UDMA=y CONFIG_TI_SCI_PROTOCOL=y@@ -103,4 +117,19 @@ CONFIG_CADENCE_QSPI=y CONFIG_SYSRESET=y CONFIG_SPL_SYSRESET=y CONFIG_SYSRESET_TI_SCI=y +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_SPL_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y +CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_SPL_USB_DWC3_GENERIC=y +CONFIG_SPL_USB_DWC3_AM62=y +CONFIG_USB_DWC3_AM62=y +CONFIG_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" +CONFIG_USB_GADGET_VENDOR_NUM=0x0451 +CONFIG_USB_GADGET_PRODUCT_NUM=0x6165 +CONFIG_USB_GADGET_DOWNLOAD=y CONFIG_FS_FAT_MAX_CLUSTSIZE=16384configs/am62x_evm_r5_usbdfu_defconfig new file +88
-0@@ -0,0 +1,111 @@ +CONFIG_ARM=y +CONFIG_ARCH_K3=y +CONFIG_SYS_MALLOC_LEN=0x08000000 +CONFIG_SYS_MALLOC_F_LEN=0x9000 +CONFIG_SPL_LIBCOMMON_SUPPORT=y +CONFIG_SPL_LIBGENERIC_SUPPORT=y +CONFIG_NR_DRAM_BANKS=2 +CONFIG_SOC_K3_AM625=y +CONFIG_TARGET_AM625_R5_EVM=y +CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y +CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x43c3a7f0 +CONFIG_ENV_SIZE=0x20000 +CONFIG_DM_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="k3-am625-r5-sk" +CONFIG_SPL_TEXT_BASE=0x43c00000 +CONFIG_DM_RESET=y +CONFIG_SPL_SERIAL=y +CONFIG_SPL_DRIVERS_MISC=y +CONFIG_SPL_STACK_R_ADDR=0x82000000 +CONFIG_SPL_SYS_MALLOC_F_LEN=0x7000 +CONFIG_SPL_SIZE_LIMIT=0x3A7F0 +CONFIG_SPL_SIZE_LIMIT_PROVIDE_STACK=0x3500 +CONFIG_SPL_LOAD_FIT=y +CONFIG_SPL_LOAD_FIT_ADDRESS=0x80080000 +# CONFIG_DISPLAY_CPUINFO is not set +CONFIG_SPL_SIZE_LIMIT_SUBTRACT_GD=y +CONFIG_SPL_SIZE_LIMIT_SUBTRACT_MALLOC=y +CONFIG_SPL_MAX_SIZE=0x3B000 +CONFIG_SPL_PAD_TO=0x0 +CONFIG_SPL_HAS_BSS_LINKER_SECTION=y +CONFIG_SPL_BSS_START_ADDR=0x43c3b000 +CONFIG_SPL_BSS_MAX_SIZE=0x3000 +CONFIG_SPL_SYS_REPORT_STACK_F_USAGE=y +CONFIG_SPL_SYS_MALLOC_SIMPLE=y +CONFIG_SPL_STACK_R=y +CONFIG_SPL_SEPARATE_BSS=y +CONFIG_SPL_EARLY_BSS=y +CONFIG_SPL_ENV_SUPPORT=y +CONFIG_SPL_DM_MAILBOX=y +CONFIG_SPL_DM_RESET=y +CONFIG_SPL_POWER_DOMAIN=y +CONFIG_SPL_RAM_SUPPORT=y +CONFIG_SPL_RAM_DEVICE=y +CONFIG_SPL_REMOTEPROC=y +CONFIG_SPL_YMODEM_SUPPORT=y +CONFIG_HUSH_PARSER=y +CONFIG_CMD_ASKENV=y +CONFIG_CMD_DFU=y +CONFIG_CMD_REMOTEPROC=y +# CONFIG_CMD_SETEXPR is not set +CONFIG_CMD_TIME=y +CONFIG_OF_CONTROL=y +CONFIG_SPL_OF_CONTROL=y +CONFIG_SPL_MULTI_DTB_FIT=y +CONFIG_SPL_MULTI_DTB_FIT_NO_COMPRESSION=y +CONFIG_SYS_RELOC_GD_ENV_ADDR=y +CONFIG_SPL_DM=y +CONFIG_SPL_DM_SEQ_ALIAS=y +CONFIG_REGMAP=y +CONFIG_SPL_REGMAP=y +CONFIG_SYSCON=y +CONFIG_SPL_SYSCON=y +CONFIG_SPL_OF_TRANSLATE=y +CONFIG_CLK=y +CONFIG_SPL_CLK=y +CONFIG_SPL_CLK_CCF=y +CONFIG_SPL_CLK_K3_PLL=y +CONFIG_SPL_CLK_K3=y +CONFIG_SYS_DFU_DATA_BUF_SIZE=0x5000 +CONFIG_TI_SCI_PROTOCOL=y +CONFIG_DA8XX_GPIO=y +CONFIG_DM_MAILBOX=y +CONFIG_K3_SEC_PROXY=y +CONFIG_MISC=y +CONFIG_ESM_K3=y +CONFIG_PINCTRL=y +# CONFIG_PINCTRL_GENERIC is not set +CONFIG_SPL_PINCTRL=y +# CONFIG_SPL_PINCTRL_GENERIC is not set +CONFIG_PINCTRL_SINGLE=y +CONFIG_POWER_DOMAIN=y +CONFIG_TI_POWER_DOMAIN=y +CONFIG_K3_SYSTEM_CONTROLLER=y +CONFIG_REMOTEPROC_TI_K3_ARM64=y +CONFIG_RESET_TI_SCI=y +CONFIG_SPECIFY_CONSOLE_INDEX=y +CONFIG_DM_SERIAL=y +CONFIG_SOC_DEVICE=y
configs/am62x_evm_r5_usbdfu_defconfig line 98
Quoted 10 lines
configs/am62x_evm_r5_usbdfu_defconfig new file +10
-0+CONFIG_SOC_DEVICE_TI_K3=y +CONFIG_SOC_TI=y +CONFIG_TIMER=y +CONFIG_SPL_TIMER=y +CONFIG_OMAP_TIMER=y +CONFIG_USB=y +CONFIG_DM_USB_GADGET=y +CONFIG_SPL_DM_USB_GADGET=y +CONFIG_USB_XHCI_HCD=y +CONFIG_USB_XHCI_DWC3=y
Do you need XHCI support for DFU mode?
Quoted 13 lines
configs/am62x_evm_r5_usbdfu_defconfig new file +13
-0+CONFIG_USB_DWC3=y +CONFIG_USB_DWC3_GENERIC=y +CONFIG_SPL_USB_DWC3_GENERIC=y +CONFIG_SPL_USB_DWC3_AM62=y +CONFIG_USB_GADGET=y +CONFIG_SPL_USB_GADGET=y +CONFIG_USB_GADGET_MANUFACTURER="Texas Instruments" +CONFIG_USB_GADGET_VENDOR_NUM=0x0451 +CONFIG_USB_GADGET_PRODUCT_NUM=0x6165 +CONFIG_USB_GADGET_DOWNLOAD=y +CONFIG_SPL_DFU=y +CONFIG_LIB_RATIONAL=y +CONFIG_SPL_LIB_RATIONAL=y
Signature · 2 lines
cheers, -roger