ARM: dts: stm32: Fix GPIO hog names on DHCOM
PATCH 1/1 ARM: dts: stm32: Fix GPIO hog names on DHCOM
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', make it so and fix the following two make dtbs_check warnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$' arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'
--- arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 4 ++-- arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)
arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi +2 -2
@@ -33,7 +33,7 @@ &gpiob { * during TX anyway and that it only controls drive enable DE * line. Hence, the RX is always enabled here. */ - rs485-rx-en { + rs485-rx-en-hog { gpio-hog; gpios = <8 GPIO_ACTIVE_HIGH>; output-low;
@@ -61,7 +61,7 @@ &gpioi { * order to reset the Hub when USB bus is powered down, but * so far there is no such functionality. */ - usb-hub { + usb-hub-hog { gpio-hog; gpios = <2 GPIO_ACTIVE_HIGH>; output-high;
arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi +1 -1
@@ -43,7 +43,7 @@ &gpioa { * in order to turn on port power when USB bus is powered up, but so * far there is no such functionality. */ - usb-port-power { + usb-port-power-hog { gpio-hog; gpios = <13 GPIO_ACTIVE_LOW>; output-low;
Signature · 7 lines
2.29.2 _______________________________________________ linux-arm-kernel mailing list [email protected] http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Alexandre TORGUE
maintainerHi Marek
Quoted 46 lines · Marek Vasut
The GPIO hog node name should match regex '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$', make it so and fix the following two make
dtbs_checkwarnings:
arch/arm/boot/dts/stm32mp157c-dhcom-picoitx.dt.yaml: hog-usb-port-power: $nodename:0: 'hog-usb-port-power' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'arch/arm/boot/dts/stm32mp153c-dhcom-drc02.dt.yaml: hog-usb-hub: $nodename:0: 'hog-usb-hub' does not match '^(hog-[0-9]+|.+-hog(-[0-9]+)?)$'Signed-off-by Marek Vasut <[email protected]>Cc Alexandre Torgue <[email protected]>Cc Maxime Coquelin <[email protected]>Cc Patrice Chotard <[email protected]>Cc Patrick Delaunay <[email protected]>--- arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 4 ++-- arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi | 2 +- 2 files changed, 3 insertions(+), 3 deletions(-)arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi +2
-2@@ -33,7 +33,7 @@ &gpiob { * during TX anyway and that it only controls drive enable DE * line. Hence, the RX is always enabled here. */ - rs485-rx-en { + rs485-rx-en-hog { gpio-hog; gpios = <8 GPIO_ACTIVE_HIGH>; output-low;@@ -61,7 +61,7 @@ &gpioi { * order to reset the Hub when USB bus is powered down, but * so far there is no such functionality. */ - usb-hub { + usb-hub-hog { gpio-hog; gpios = <2 GPIO_ACTIVE_HIGH>; output-high;arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi +0
-0
arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi &gpioa { · line 49
Quoted 8 lines
arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi +1
-1@@ -43,7 +43,7 @@ &gpioa { * in order to turn on port power when USB bus is powered up, but so * far there is no such functionality. */ - usb-port-power { + usb-port-power-hog { gpio-hog; gpios = <13 GPIO_ACTIVE_LOW>; output-low;
Applied on stm32-fixes with a Fixes tag added.
Thanks.
Alex
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel