stm32mp: Add support of OP-TEE and STM32MP13x in bsec driver
Subsystems (3)
cover stm32mp: Add support of OP-TEE and STM32MP13x in bsec driver
Add support of STM32MP13x in bsec driver with OP-TEE pseudo TA and activate the associated commands fuse, stboard and stm32key.
This PTA is merged in OP-TEE master branch, and can be used for STM32MP15X and STM32MP13X SoC to access to BSEC secured ressource.
This serie is a preliminary step for STM32MP13x USB support, with serial number and for ETH with mac address.
Patrick
Patrick Delaunay (6):
stm32mp: cosmetic: Update of bsec driver
stm32mp: Add OP-TEE support in bsec driver
stm32mp: Add support of STM32MP13x in bsec driver
configs: stm32mp13: Activate CONFIG_CMD_FUSE
board: st: Add support of STM32MP13x boards in stm32board cmd
configs: stm32mp13: Activate command stm32key
arch/arm/mach-stm32mp/bsec.c | 176 +++++++++++++++++++++- arch/arm/mach-stm32mp/cmd_stm32key.c | 4 +- arch/arm/mach-stm32mp/include/mach/bsec.h | 7 + board/st/common/Kconfig | 2 +- board/st/common/cmd_stboard.c | 12 +- configs/stm32mp13_defconfig | 2 + doc/board/st/stm32mp1.rst | 6 +- 7 files changed, 191 insertions(+), 18 deletions(-)
Signature · 1 line
2.25.1
PATCH 1/6 stm32mp: cosmetic: Update of bsec driver
Remove unnecessary return in stm32mp_bsec_write_lock and replace tab by space for plat_auto opts.
---
arch/arm/mach-stm32mp/bsec.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)
arch/arm/mach-stm32mp/bsec.c +1 -3
@@ -468,8 +468,6 @@ static int stm32mp_bsec_write_lock(struct udevice *dev, u32 val, u32 otp) plat =dev_get_plat (dev);return bsec_permanent_lock_otp (dev, plat->base, otp); - -return -EINVAL ; } static int stm32mp_bsec_read(struct udevice *dev, int offset,
@@ -608,7 +606,7 @@ U_BOOT_DRIVER(stm32mp_bsec) = { .id = UCLASS_MISC, .of_match = stm32mp_bsec_ids, .of_to_plat = stm32mp_bsec_of_to_plat, - .plat_auto = sizeof(struct stm32mp_bsec_plat), + .plat_auto = sizeof(struct stm32mp_bsec_plat), .ops = &stm32mp_bsec_ops, .probe = stm32mp_bsec_probe, };
Signature · 1 line
2.25.1
Re: [PATCH 1/6] stm32mp: cosmetic: Update of bsec driver
Hi Patrick
Quoted 23 lines · Patrick Delaunay
Remove unnecessary return in
stm32mp_bsec_write_lockand replace tab by space forplat_autoopts.Signed-off-by Patrick Delaunay <[email protected]>---
arch/arm/mach-stm32mp/bsec.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)arch/arm/mach-stm32mp/bsec.c +0
-2@@ -468,8 +468,6 @@ static int stm32mp_bsec_write_lock(struct udevice *dev, u32 val, u32 otp) plat =dev_get_plat (dev);return bsec_permanent_lock_otp (dev, plat->base, otp); - -return -EINVAL ; } static int stm32mp_bsec_read(struct udevice *dev, int offset,
arch/arm/mach-stm32mp/bsec.c U_BOOT_DRIVER(stm32mp_bsec) = { · line 612
Quoted 8 lines
arch/arm/mach-stm32mp/bsec.c +1
-1@@ -608,7 +606,7 @@ U_BOOT_DRIVER(stm32mp_bsec) = { .id = UCLASS_MISC, .of_match = stm32mp_bsec_ids, .of_to_plat = stm32mp_bsec_of_to_plat, - .plat_auto = sizeof(struct stm32mp_bsec_plat), + .plat_auto = sizeof(struct stm32mp_bsec_plat), .ops = &stm32mp_bsec_ops, .probe = stm32mp_bsec_probe, };
Thanks
Patrice
Re: [PATCH 1/6] stm32mp: cosmetic: Update of bsec driver
In reply to Patrick DelaunayHi Patrick
Quoted 23 lines · Patrick Delaunay
Remove unnecessary return in
stm32mp_bsec_write_lockand replace tab by space forplat_autoopts.Signed-off-by Patrick Delaunay <[email protected]>---
arch/arm/mach-stm32mp/bsec.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-)arch/arm/mach-stm32mp/bsec.c +0
-2@@ -468,8 +468,6 @@ static int stm32mp_bsec_write_lock(struct udevice *dev, u32 val, u32 otp) plat =dev_get_plat (dev);return bsec_permanent_lock_otp (dev, plat->base, otp); - -return -EINVAL ; } static int stm32mp_bsec_read(struct udevice *dev, int offset,
arch/arm/mach-stm32mp/bsec.c U_BOOT_DRIVER(stm32mp_bsec) = { · line 612
Quoted 8 lines
arch/arm/mach-stm32mp/bsec.c +1
-1@@ -608,7 +606,7 @@ U_BOOT_DRIVER(stm32mp_bsec) = { .id = UCLASS_MISC, .of_match = stm32mp_bsec_ids, .of_to_plat = stm32mp_bsec_of_to_plat, - .plat_auto = sizeof(struct stm32mp_bsec_plat), + .plat_auto = sizeof(struct stm32mp_bsec_plat), .ops = &stm32mp_bsec_ops, .probe = stm32mp_bsec_probe, };
Applied to u-boot-stm32/master
Thanks
Patrice
PATCH 2/6 stm32mp: Add OP-TEE support in bsec driver
In reply to Patrick DelaunayWhen OP-TEE is used, the SMC for BSEC management are not available and the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13 and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle the BSEC_LOCK_PERM lock value instead of 1.
---
arch/arm/mach-stm32mp/bsec.c | 173 +++++++++++++++++++++- arch/arm/mach-stm32mp/cmd_stm32key.c | 4 +- arch/arm/mach-stm32mp/include/mach/bsec.h | 7 + board/st/common/cmd_stboard.c | 5 +- doc/board/st/stm32mp1.rst | 6 +- 5 files changed, 183 insertions(+), 12 deletions(-)
arch/arm/mach-stm32mp/bsec.c +169 -4
@@ -10,9 +10,11 @@#include <dm.h> #include <log.h> #include <misc.h> +#include <tee.h> #include <asm/io.h> #include <asm/arch/bsec.h> #include <asm/arch/stm32mp1_smc.h> +#include <dm/device.h> #include <dm/device_compat.h> #include <linux/arm-smccc.h> #include <linux/iopoll.h>
@@ -63,10 +65,43 @@*/ #define BSEC_LOCK_PROGRAM 0x04 +#define PTA_BSEC_UUID { 0x94cf71ad, 0x80e6, 0x40b5, \ + { 0xa7, 0xc6, 0x3d, 0xc5, 0x01, 0xeb, 0x28, 0x03 } } + +/* +* Read OTP memory +* +* [in] value[0].a OTP start offset in byte +* [in] value[0].b Access type (0:shadow, 1:fuse, 2:lock) +* [out] memref[1].buffer Output buffer to store read values +* [out] memref[1].size Size of OTP to be read +* +* Return codes: +* TEE_SUCCESS - Invoke command success +* TEE_ERROR_BAD_PARAMETERS - Incorrect input param +* TEE_ERROR_ACCESS_DENIED - OTP not accessible by caller +*/ +#define PTA_BSEC_READ_MEM 0x0 +/* -* OTP status: bit 0 permanent lock +* Write OTP memory +* +* [in] value[0].a OTP start offset in byte +* [in] value[0].b Access type (0:shadow, 1:fuse, 2:lock) +* [in] memref[1].buffer Input buffer to read values +* [in] memref[1].size Size of OTP to be written +* +* Return codes: +* TEE_SUCCESS - Invoke command success +* TEE_ERROR_BAD_PARAMETERS - Incorrect input param +* TEE_ERROR_ACCESS_DENIED - OTP not accessible by caller */ -#define BSEC_LOCK_PERM BIT(0) +#define PTA_BSEC_WRITE_MEM 0x1 + +/* value of PTA_BSEC access type = value[in] b */ +#define SHADOW_ACCESS 0 +#define FUSE_ACCESS 1 +#define LOCK_ACCESS 2/** * bsec_lock() - manage lock for each type SR/SP/SW
@@ -359,6 +394,10 @@ struct stm32mp_bsec_plat {u32 base; }; +struct stm32mp_bsec_priv { +struct udevice *tee; +}; +static int stm32mp_bsec_read_otp (struct udevice *dev,u32 *val,u32 otp) {struct stm32mp_bsec_plat *plat;
@@ -470,14 +509,109 @@ static int stm32mp_bsec_write_lock(struct udevice *dev, u32 val, u32 otp)return bsec_permanent_lock_otp (dev, plat->base, otp); } +static int bsec_pta_open_session (struct udevice *tee,u32 *tee_session) +{ +const struct tee_optee_ta_uuid uuid =PTA_BSEC_UUID ; +struct tee_open_session_arg arg; +int rc; + +memset (&arg,0 ,sizeof (arg)); +tee_optee_ta_uuid_to_octets (arg.uuid, &uuid); + arg.clnt_login =TEE_LOGIN_REE_KERNEL ; + rc =tee_open_session (tee, &arg,0 ,NULL ); +if (rc <0 ) +return -ENODEV ; + + *tee_session = arg.session; + +return 0 ; +} + +static int bsec_optee_open (struct udevice *dev) +{ +struct stm32mp_bsec_priv *priv =dev_get_priv (dev); +struct udevice *tee; +u32 tee_session; +int rc; + + tee =tee_find_device (NULL ,NULL ,NULL ,NULL ); +if (!tee) +return -ENODEV ; + +/* try to open the STM32 BSEC TA */ + rc =bsec_pta_open_session (tee, &tee_session); +if (rc) +return rc; + +tee_close_session (tee, tee_session); + + priv->tee = tee; + +return 0 ; +} + +static int bsec_optee_pta (struct udevice *dev,int cmd,int type,int offset, +void *buff,ulong size) +{ +struct stm32mp_bsec_priv *priv =dev_get_priv (dev); +u32 tee_session; +struct tee_invoke_arg arg; +struct tee_param param[2 ]; +struct tee_shm *fw_shm; +int rc; + + rc =bsec_pta_open_session (priv->tee, &tee_session); +if (rc) +return rc; + + rc =tee_shm_register (priv->tee, buff, size,0 , &fw_shm); +if (rc) + goto close_session; + +memset (&arg,0 ,sizeof (arg)); + arg.func = cmd; + arg.session = tee_session; + +memset (param,0 ,sizeof (param)); + + param[0 ].attr =TEE_PARAM_ATTR_TYPE_VALUE_INPUT ; + param[0 ].u.value.a = offset; + param[0 ].u.value.b = type; + +if (cmd ==PTA_BSEC_WRITE_MEM ) + param[1 ].attr =TEE_PARAM_ATTR_TYPE_MEMREF_INPUT ; +else + param[1 ].attr =TEE_PARAM_ATTR_TYPE_MEMREF_OUTPUT ; + + param[1 ].u.memref.shm = fw_shm; + param[1 ].u.memref.size = size; + + rc =tee_invoke_func (priv->tee, &arg,2 , param); +if (rc <0 || arg.ret !=0 ) { +dev_err (priv->tee, +"PTA_BSEC invoke failed TEE err: %x, err:%x\n" , + arg.ret, rc); +if (!rc) + rc = -EIO ; + } + +tee_shm_free (fw_shm); + +close_session: +tee_close_session (priv->tee, tee_session); + +return rc; +} +static int stm32mp_bsec_read (struct udevice *dev,int offset,void *buf,int size) { +struct stm32mp_bsec_priv *priv =dev_get_priv (dev);int ret;int i;bool shadow = true, lock = false;int nb_otp = size /sizeof (u32); -int otp; +int otp, cmd;unsigned int offs = offset;if (offs >=STM32_BSEC_LOCK_OFFSET ) {
@@ -491,6 +625,19 @@ static int stm32mp_bsec_read(struct udevice *dev, int offset,if ((offs %4 ) || (size %4 ))return -EINVAL ; +if (IS_ENABLED (CONFIG_OPTEE ) && priv->tee) { + cmd =FUSE_ACCESS ; +if (shadow) + cmd =SHADOW_ACCESS ; +if (lock) + cmd =LOCK_ACCESS ; + ret =bsec_optee_pta (dev,PTA_BSEC_READ_MEM , cmd, offs, buf, size); +if (ret) +return ret; + +return size; + } + otp = offs /sizeof (u32);for (i = otp; i < (otp + nb_otp) && i <=BSEC_OTP_MAX_VALUE ; i++) {
@@ -515,11 +662,12 @@ static int stm32mp_bsec_read(struct udevice *dev, int offset,static int stm32mp_bsec_write (struct udevice *dev,int offset,const void *buf,int size) { +struct stm32mp_bsec_priv *priv =dev_get_priv (dev);int ret =0 ;int i;bool shadow = true, lock = false;int nb_otp = size /sizeof (u32); -int otp; +int otp, cmd;unsigned int offs = offset;if (offs >=STM32_BSEC_LOCK_OFFSET ) {
@@ -533,6 +681,19 @@ static int stm32mp_bsec_write(struct udevice *dev, int offset,if ((offs %4 ) || (size %4 ))return -EINVAL ; +if (IS_ENABLED (CONFIG_OPTEE ) && priv->tee) { + cmd =FUSE_ACCESS ; +if (shadow) + cmd =SHADOW_ACCESS ; +if (lock) + cmd =LOCK_ACCESS ; + ret =bsec_optee_pta (dev,PTA_BSEC_WRITE_MEM , cmd, offs, (void *)buf, size); +if (ret) +return ret; + +return size; + } + otp = offs /sizeof (u32);for (i = otp; i < otp + nb_otp && i <=BSEC_OTP_MAX_VALUE ; i++) {
@@ -581,6 +742,9 @@ static int stm32mp_bsec_probe(struct udevice *dev)return ret; } +if (IS_ENABLED (CONFIG_OPTEE )) +bsec_optee_open (dev); +/* * update unlocked shadow for OTP cleared by the rom code * only executed in SPL, it is done in TF-A for TFABOOT
@@ -607,6 +771,7 @@ U_BOOT_DRIVER(stm32mp_bsec) = { .of_match = stm32mp_bsec_ids, .of_to_plat = stm32mp_bsec_of_to_plat, .plat_auto = sizeof(struct stm32mp_bsec_plat), + .priv_auto = sizeof(struct stm32mp_bsec_priv), .ops = &stm32mp_bsec_ops, .probe = stm32mp_bsec_probe, };
arch/arm/mach-stm32mp/cmd_stm32key.c +1 -3
@@ -8,6 +8,7 @@#include <console.h> #include <log.h> #include <misc.h> +#include <asm/arch/bsec.h> #include <dm/device.h> #include <dm/uclass.h>
@@ -84,9 +85,6 @@ static u32 get_otp_close_mask(void)return STM32_OTP_STM32MP15x_CLOSE_MASK; } -#define BSEC_LOCK_ERROR (-1) -#define BSEC_LOCK_PERM BIT(0) -static int get_misc_dev (struct udevice **dev) {int ret;
arch/arm/mach-stm32mp/include/mach/bsec.h +7 -0
@@ -5,3 +5,10 @@/* check self hosted debug status = BSEC_DENABLE.DBGSWENABLE */ bool bsec_dbgswenable (void ); + +/* Bitfield definition for LOCK status */ +#define BSEC_LOCK_PERM BIT(30) +#define BSEC_LOCK_SHADOW_R BIT(29) +#define BSEC_LOCK_SHADOW_W BIT(28) +#define BSEC_LOCK_SHADOW_P BIT(27) +#define BSEC_LOCK_ERROR BIT(26)
board/st/common/cmd_stboard.c +3 -2
@@ -34,6 +34,7 @@#include <command.h> #include <console.h> #include <misc.h> +#include <asm/arch/bsec.h> #include <dm/device.h> #include <dm/uclass.h>
@@ -109,7 +110,7 @@ static int do_stboard(struct cmd_tbl *cmdtp, int flag, int argc,else display_stboard (otp);printf (" OTP %d %s locked !\n" ,BSEC_OTP_BOARD , - lock ==1 ?"" :"NOT" ); + lock &BSEC_LOCK_PERM ?"" :"NOT" );return CMD_RET_SUCCESS ; }
@@ -178,7 +179,7 @@ static int do_stboard(struct cmd_tbl *cmdtp, int flag, int argc, }/* write persistent lock */ - otp =1 ; + otp =BSEC_LOCK_PERM ; ret =misc_write (dev,STM32_BSEC_LOCK (BSEC_OTP_BOARD ), &otp,sizeof (otp));if (ret !=sizeof (otp)) {
doc/board/st/stm32mp1.rst +3 -3
@@ -620,7 +620,7 @@ Prerequisite: check if a MAC address isn't yet programmed in OTP STM32MP> env print ethaddr ## Error: "ethaddr" not defined -3) check lock status of fuse 57 & 58 (at 0x39, 0=unlocked, 1=locked):: +3) check lock status of fuse 57 & 58 (at 0x39, 0=unlocked, 0x40000000=locked):: STM32MP> fuse sense 0 0x10000039 2 Sensing bank 0:
@@ -640,11 +640,11 @@ Example to set mac address "12:34:56:78:9a:bc" 3) Lock OTP:: - STM32MP> fuse prog 0 0x10000039 1 1 + STM32MP> fuse prog 0 0x10000039 0x40000000 0x40000000 STM32MP> fuse sense 0 0x10000039 2 Sensing bank 0: - Word 0x10000039: 00000001 00000001 + Word 0x10000039: 40000000 40000000 4) next REBOOT, in the trace::
Signature · 1 line
2.25.1
Re: [PATCH 2/6] stm32mp: Add OP-TEE support in bsec driver
Hi Patrick
Quoted 360 lines · Patrick Delaunay
When OP-TEE is used, the SMC for BSEC management are not available and the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13 and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle the
BSEC_LOCK_PERMlock value instead of 1.Signed-off-by Patrick Delaunay <[email protected]>---
arch/arm/mach-stm32mp/bsec.c | 173 +++++++++++++++++++++- arch/arm/mach-stm32mp/cmd_stm32key.c | 4 +- arch/arm/mach-stm32mp/include/mach/bsec.h | 7 + board/st/common/cmd_stboard.c | 5 +- doc/board/st/stm32mp1.rst | 6 +- 5 files changed, 183 insertions(+), 12 deletions(-)arch/arm/mach-stm32mp/bsec.c +169
-4@@ -10,9 +10,11 @@#include <dm.h> #include <log.h> #include <misc.h> +#include <tee.h> #include <asm/io.h> #include <asm/arch/bsec.h> #include <asm/arch/stm32mp1_smc.h> +#include <dm/device.h> #include <dm/device_compat.h> #include <linux/arm-smccc.h> #include <linux/iopoll.h> @@ -63,10 +65,43 @@*/ #define BSEC_LOCK_PROGRAM 0x04 +#define PTA_BSEC_UUID { 0x94cf71ad, 0x80e6, 0x40b5, \ + { 0xa7, 0xc6, 0x3d, 0xc5, 0x01, 0xeb, 0x28, 0x03 } } + +/* +* Read OTP memory +* +* [in] value[0].a OTP start offset in byte +* [in] value[0].b Access type (0:shadow, 1:fuse, 2:lock) +* [out] memref[1].buffer Output buffer to store read values +* [out] memref[1].size Size of OTP to be read +* +* Return codes: +* TEE_SUCCESS - Invoke command success +* TEE_ERROR_BAD_PARAMETERS - Incorrect input param +* TEE_ERROR_ACCESS_DENIED - OTP not accessible by caller +*/ +#define PTA_BSEC_READ_MEM 0x0 +/* -* OTP status: bit 0 permanent lock +* Write OTP memory +* +* [in] value[0].a OTP start offset in byte +* [in] value[0].b Access type (0:shadow, 1:fuse, 2:lock) +* [in] memref[1].buffer Input buffer to read values +* [in] memref[1].size Size of OTP to be written +* +* Return codes: +* TEE_SUCCESS - Invoke command success +* TEE_ERROR_BAD_PARAMETERS - Incorrect input param +* TEE_ERROR_ACCESS_DENIED - OTP not accessible by caller */ -#define BSEC_LOCK_PERM BIT(0) +#define PTA_BSEC_WRITE_MEM 0x1 + +/* value of PTA_BSEC access type = value[in] b */ +#define SHADOW_ACCESS 0 +#define FUSE_ACCESS 1 +#define LOCK_ACCESS 2/** * bsec_lock() - manage lock for each type SR/SP/SW @@ -359,6 +394,10 @@ struct stm32mp_bsec_plat {u32 base; }; +struct stm32mp_bsec_priv { +struct udevice *tee; +}; +static int stm32mp_bsec_read_otp (struct udevice *dev,u32 *val,u32 otp) {struct stm32mp_bsec_plat *plat;@@ -470,14 +509,109 @@ static int stm32mp_bsec_write_lock(struct udevice *dev, u32 val, u32 otp)return bsec_permanent_lock_otp (dev, plat->base, otp); } +static int bsec_pta_open_session (struct udevice *tee,u32 *tee_session) +{ +const struct tee_optee_ta_uuid uuid =PTA_BSEC_UUID ; +struct tee_open_session_arg arg; +int rc; + +memset (&arg,0 ,sizeof (arg)); +tee_optee_ta_uuid_to_octets (arg.uuid, &uuid); + arg.clnt_login =TEE_LOGIN_REE_KERNEL ; + rc =tee_open_session (tee, &arg,0 ,NULL ); +if (rc <0 ) +return -ENODEV ; + + *tee_session = arg.session; + +return 0 ; +} + +static int bsec_optee_open (struct udevice *dev) +{ +struct stm32mp_bsec_priv *priv =dev_get_priv (dev); +struct udevice *tee; +u32 tee_session; +int rc; + + tee =tee_find_device (NULL ,NULL ,NULL ,NULL ); +if (!tee) +return -ENODEV ; + +/* try to open the STM32 BSEC TA */ + rc =bsec_pta_open_session (tee, &tee_session); +if (rc) +return rc; + +tee_close_session (tee, tee_session); + + priv->tee = tee; + +return 0 ; +} + +static int bsec_optee_pta (struct udevice *dev,int cmd,int type,int offset, +void *buff,ulong size) +{ +struct stm32mp_bsec_priv *priv =dev_get_priv (dev); +u32 tee_session; +struct tee_invoke_arg arg; +struct tee_param param[2 ]; +struct tee_shm *fw_shm; +int rc; + + rc =bsec_pta_open_session (priv->tee, &tee_session); +if (rc) +return rc; + + rc =tee_shm_register (priv->tee, buff, size,0 , &fw_shm); +if (rc) + goto close_session; + +memset (&arg,0 ,sizeof (arg)); + arg.func = cmd; + arg.session = tee_session; + +memset (param,0 ,sizeof (param)); + + param[0 ].attr =TEE_PARAM_ATTR_TYPE_VALUE_INPUT ; + param[0 ].u.value.a = offset; + param[0 ].u.value.b = type; + +if (cmd ==PTA_BSEC_WRITE_MEM ) + param[1 ].attr =TEE_PARAM_ATTR_TYPE_MEMREF_INPUT ; +else + param[1 ].attr =TEE_PARAM_ATTR_TYPE_MEMREF_OUTPUT ; + + param[1 ].u.memref.shm = fw_shm; + param[1 ].u.memref.size = size; + + rc =tee_invoke_func (priv->tee, &arg,2 , param); +if (rc <0 || arg.ret !=0 ) { +dev_err (priv->tee, +"PTA_BSEC invoke failed TEE err: %x, err:%x\n" , + arg.ret, rc); +if (!rc) + rc = -EIO ; + } + +tee_shm_free (fw_shm); + +close_session: +tee_close_session (priv->tee, tee_session); + +return rc; +} +static int stm32mp_bsec_read (struct udevice *dev,int offset,void *buf,int size) { +struct stm32mp_bsec_priv *priv =dev_get_priv (dev);int ret;int i;bool shadow = true, lock = false;int nb_otp = size /sizeof (u32); -int otp; +int otp, cmd;unsigned int offs = offset;if (offs >=STM32_BSEC_LOCK_OFFSET ) {@@ -491,6 +625,19 @@ static int stm32mp_bsec_read(struct udevice *dev, int offset,if ((offs %4 ) || (size %4 ))return -EINVAL ; +if (IS_ENABLED (CONFIG_OPTEE ) && priv->tee) { + cmd =FUSE_ACCESS ; +if (shadow) + cmd =SHADOW_ACCESS ; +if (lock) + cmd =LOCK_ACCESS ; + ret =bsec_optee_pta (dev,PTA_BSEC_READ_MEM , cmd, offs, buf, size); +if (ret) +return ret; + +return size; + } + otp = offs /sizeof (u32);for (i = otp; i < (otp + nb_otp) && i <=BSEC_OTP_MAX_VALUE ; i++) {@@ -515,11 +662,12 @@ static int stm32mp_bsec_read(struct udevice *dev, int offset,static int stm32mp_bsec_write (struct udevice *dev,int offset,const void *buf,int size) { +struct stm32mp_bsec_priv *priv =dev_get_priv (dev);int ret =0 ;int i;bool shadow = true, lock = false;int nb_otp = size /sizeof (u32); -int otp; +int otp, cmd;unsigned int offs = offset;if (offs >=STM32_BSEC_LOCK_OFFSET ) {@@ -533,6 +681,19 @@ static int stm32mp_bsec_write(struct udevice *dev, int offset,if ((offs %4 ) || (size %4 ))return -EINVAL ; +if (IS_ENABLED (CONFIG_OPTEE ) && priv->tee) { + cmd =FUSE_ACCESS ; +if (shadow) + cmd =SHADOW_ACCESS ; +if (lock) + cmd =LOCK_ACCESS ; + ret =bsec_optee_pta (dev,PTA_BSEC_WRITE_MEM , cmd, offs, (void *)buf, size); +if (ret) +return ret; + +return size; + } + otp = offs /sizeof (u32);for (i = otp; i < otp + nb_otp && i <=BSEC_OTP_MAX_VALUE ; i++) {@@ -581,6 +742,9 @@ static int stm32mp_bsec_probe(struct udevice *dev)return ret; } +if (IS_ENABLED (CONFIG_OPTEE )) +bsec_optee_open (dev); +/* * update unlocked shadow for OTP cleared by the rom code * only executed in SPL, it is done in TF-A for TFABOOT @@ -607,6 +771,7 @@ U_BOOT_DRIVER(stm32mp_bsec) = { .of_match = stm32mp_bsec_ids, .of_to_plat = stm32mp_bsec_of_to_plat, .plat_auto = sizeof(struct stm32mp_bsec_plat), + .priv_auto = sizeof(struct stm32mp_bsec_priv), .ops = &stm32mp_bsec_ops, .probe = stm32mp_bsec_probe, };arch/arm/mach-stm32mp/cmd_stm32key.c +1
-3@@ -8,6 +8,7 @@#include <console.h> #include <log.h> #include <misc.h> +#include <asm/arch/bsec.h> #include <dm/device.h> #include <dm/uclass.h> @@ -84,9 +85,6 @@ static u32 get_otp_close_mask(void)return STM32_OTP_STM32MP15x_CLOSE_MASK; } -#define BSEC_LOCK_ERROR (-1) -#define BSEC_LOCK_PERM BIT(0) -static int get_misc_dev (struct udevice **dev) {int ret;arch/arm/mach-stm32mp/include/mach/bsec.h +7
-0@@ -5,3 +5,10 @@/* check self hosted debug status = BSEC_DENABLE.DBGSWENABLE */ bool bsec_dbgswenable (void ); + +/* Bitfield definition for LOCK status */ +#define BSEC_LOCK_PERM BIT(30) +#define BSEC_LOCK_SHADOW_R BIT(29) +#define BSEC_LOCK_SHADOW_W BIT(28) +#define BSEC_LOCK_SHADOW_P BIT(27) +#define BSEC_LOCK_ERROR BIT(26)board/st/common/cmd_stboard.c +3
-2@@ -34,6 +34,7 @@#include <command.h> #include <console.h> #include <misc.h> +#include <asm/arch/bsec.h> #include <dm/device.h> #include <dm/uclass.h> @@ -109,7 +110,7 @@ static int do_stboard(struct cmd_tbl *cmdtp, int flag, int argc,else display_stboard (otp);printf (" OTP %d %s locked !\n" ,BSEC_OTP_BOARD , - lock ==1 ?"" :"NOT" ); + lock &BSEC_LOCK_PERM ?"" :"NOT" );return CMD_RET_SUCCESS ; }@@ -178,7 +179,7 @@ static int do_stboard(struct cmd_tbl *cmdtp, int flag, int argc, }/* write persistent lock */ - otp =1 ; + otp =BSEC_LOCK_PERM ; ret =misc_write (dev,STM32_BSEC_LOCK (BSEC_OTP_BOARD ), &otp,sizeof (otp));if (ret !=sizeof (otp)) {doc/board/st/stm32mp1.rst +1
-1@@ -620,7 +620,7 @@ Prerequisite: check if a MAC address isn't yet programmed in OTP STM32MP> env print ethaddr ## Error: "ethaddr" not defined -3) check lock status of fuse 57 & 58 (at 0x39, 0=unlocked, 1=locked):: +3) check lock status of fuse 57 & 58 (at 0x39, 0=unlocked, 0x40000000=locked):: STM32MP> fuse sense 0 0x10000039 2 Sensing bank 0:@@ -640,11 +640,11 @@ Example to set mac address "12:34:56:78:9a:bc" 3) Lock OTP::
doc/board/st/stm32mp1.rst Example to set mac address "12:34:56:78:9a:bc" · line 650
Quoted 10 lines
doc/board/st/stm32mp1.rst +2
-2- STM32MP> fuse prog 0 0x10000039 1 1 + STM32MP> fuse prog 0 0x10000039 0x40000000 0x40000000 STM32MP> fuse sense 0 0x10000039 2 Sensing bank 0: - Word 0x10000039: 00000001 00000001 + Word 0x10000039: 40000000 40000000 4) next REBOOT, in the trace::
Thanks
Patrice
Re: [PATCH 2/6] stm32mp: Add OP-TEE support in bsec driver
In reply to Patrick DelaunayHI Patrick
Quoted 360 lines · Patrick Delaunay
When OP-TEE is used, the SMC for BSEC management are not available and the STM32MP BSEC pseudo TA must be used (it is mandatory for STM32MP13 and it is a new feature for STM32MP15x).
The BSEC driver try to open a session to this PTA BSEC at probe and use it for OTP read or write access to fuse or to shadow.
This patch also adapts the commands stm32key and stboard to handle the
BSEC_LOCK_PERMlock value instead of 1.Signed-off-by Patrick Delaunay <[email protected]>---
arch/arm/mach-stm32mp/bsec.c | 173 +++++++++++++++++++++- arch/arm/mach-stm32mp/cmd_stm32key.c | 4 +- arch/arm/mach-stm32mp/include/mach/bsec.h | 7 + board/st/common/cmd_stboard.c | 5 +- doc/board/st/stm32mp1.rst | 6 +- 5 files changed, 183 insertions(+), 12 deletions(-)arch/arm/mach-stm32mp/bsec.c +169
-4@@ -10,9 +10,11 @@#include <dm.h> #include <log.h> #include <misc.h> +#include <tee.h> #include <asm/io.h> #include <asm/arch/bsec.h> #include <asm/arch/stm32mp1_smc.h> +#include <dm/device.h> #include <dm/device_compat.h> #include <linux/arm-smccc.h> #include <linux/iopoll.h> @@ -63,10 +65,43 @@*/ #define BSEC_LOCK_PROGRAM 0x04 +#define PTA_BSEC_UUID { 0x94cf71ad, 0x80e6, 0x40b5, \ + { 0xa7, 0xc6, 0x3d, 0xc5, 0x01, 0xeb, 0x28, 0x03 } } + +/* +* Read OTP memory +* +* [in] value[0].a OTP start offset in byte +* [in] value[0].b Access type (0:shadow, 1:fuse, 2:lock) +* [out] memref[1].buffer Output buffer to store read values +* [out] memref[1].size Size of OTP to be read +* +* Return codes: +* TEE_SUCCESS - Invoke command success +* TEE_ERROR_BAD_PARAMETERS - Incorrect input param +* TEE_ERROR_ACCESS_DENIED - OTP not accessible by caller +*/ +#define PTA_BSEC_READ_MEM 0x0 +/* -* OTP status: bit 0 permanent lock +* Write OTP memory +* +* [in] value[0].a OTP start offset in byte +* [in] value[0].b Access type (0:shadow, 1:fuse, 2:lock) +* [in] memref[1].buffer Input buffer to read values +* [in] memref[1].size Size of OTP to be written +* +* Return codes: +* TEE_SUCCESS - Invoke command success +* TEE_ERROR_BAD_PARAMETERS - Incorrect input param +* TEE_ERROR_ACCESS_DENIED - OTP not accessible by caller */ -#define BSEC_LOCK_PERM BIT(0) +#define PTA_BSEC_WRITE_MEM 0x1 + +/* value of PTA_BSEC access type = value[in] b */ +#define SHADOW_ACCESS 0 +#define FUSE_ACCESS 1 +#define LOCK_ACCESS 2/** * bsec_lock() - manage lock for each type SR/SP/SW @@ -359,6 +394,10 @@ struct stm32mp_bsec_plat {u32 base; }; +struct stm32mp_bsec_priv { +struct udevice *tee; +}; +static int stm32mp_bsec_read_otp (struct udevice *dev,u32 *val,u32 otp) {struct stm32mp_bsec_plat *plat;@@ -470,14 +509,109 @@ static int stm32mp_bsec_write_lock(struct udevice *dev, u32 val, u32 otp)return bsec_permanent_lock_otp (dev, plat->base, otp); } +static int bsec_pta_open_session (struct udevice *tee,u32 *tee_session) +{ +const struct tee_optee_ta_uuid uuid =PTA_BSEC_UUID ; +struct tee_open_session_arg arg; +int rc; + +memset (&arg,0 ,sizeof (arg)); +tee_optee_ta_uuid_to_octets (arg.uuid, &uuid); + arg.clnt_login =TEE_LOGIN_REE_KERNEL ; + rc =tee_open_session (tee, &arg,0 ,NULL ); +if (rc <0 ) +return -ENODEV ; + + *tee_session = arg.session; + +return 0 ; +} + +static int bsec_optee_open (struct udevice *dev) +{ +struct stm32mp_bsec_priv *priv =dev_get_priv (dev); +struct udevice *tee; +u32 tee_session; +int rc; + + tee =tee_find_device (NULL ,NULL ,NULL ,NULL ); +if (!tee) +return -ENODEV ; + +/* try to open the STM32 BSEC TA */ + rc =bsec_pta_open_session (tee, &tee_session); +if (rc) +return rc; + +tee_close_session (tee, tee_session); + + priv->tee = tee; + +return 0 ; +} + +static int bsec_optee_pta (struct udevice *dev,int cmd,int type,int offset, +void *buff,ulong size) +{ +struct stm32mp_bsec_priv *priv =dev_get_priv (dev); +u32 tee_session; +struct tee_invoke_arg arg; +struct tee_param param[2 ]; +struct tee_shm *fw_shm; +int rc; + + rc =bsec_pta_open_session (priv->tee, &tee_session); +if (rc) +return rc; + + rc =tee_shm_register (priv->tee, buff, size,0 , &fw_shm); +if (rc) + goto close_session; + +memset (&arg,0 ,sizeof (arg)); + arg.func = cmd; + arg.session = tee_session; + +memset (param,0 ,sizeof (param)); + + param[0 ].attr =TEE_PARAM_ATTR_TYPE_VALUE_INPUT ; + param[0 ].u.value.a = offset; + param[0 ].u.value.b = type; + +if (cmd ==PTA_BSEC_WRITE_MEM ) + param[1 ].attr =TEE_PARAM_ATTR_TYPE_MEMREF_INPUT ; +else + param[1 ].attr =TEE_PARAM_ATTR_TYPE_MEMREF_OUTPUT ; + + param[1 ].u.memref.shm = fw_shm; + param[1 ].u.memref.size = size; + + rc =tee_invoke_func (priv->tee, &arg,2 , param); +if (rc <0 || arg.ret !=0 ) { +dev_err (priv->tee, +"PTA_BSEC invoke failed TEE err: %x, err:%x\n" , + arg.ret, rc); +if (!rc) + rc = -EIO ; + } + +tee_shm_free (fw_shm); + +close_session: +tee_close_session (priv->tee, tee_session); + +return rc; +} +static int stm32mp_bsec_read (struct udevice *dev,int offset,void *buf,int size) { +struct stm32mp_bsec_priv *priv =dev_get_priv (dev);int ret;int i;bool shadow = true, lock = false;int nb_otp = size /sizeof (u32); -int otp; +int otp, cmd;unsigned int offs = offset;if (offs >=STM32_BSEC_LOCK_OFFSET ) {@@ -491,6 +625,19 @@ static int stm32mp_bsec_read(struct udevice *dev, int offset,if ((offs %4 ) || (size %4 ))return -EINVAL ; +if (IS_ENABLED (CONFIG_OPTEE ) && priv->tee) { + cmd =FUSE_ACCESS ; +if (shadow) + cmd =SHADOW_ACCESS ; +if (lock) + cmd =LOCK_ACCESS ; + ret =bsec_optee_pta (dev,PTA_BSEC_READ_MEM , cmd, offs, buf, size); +if (ret) +return ret; + +return size; + } + otp = offs /sizeof (u32);for (i = otp; i < (otp + nb_otp) && i <=BSEC_OTP_MAX_VALUE ; i++) {@@ -515,11 +662,12 @@ static int stm32mp_bsec_read(struct udevice *dev, int offset,static int stm32mp_bsec_write (struct udevice *dev,int offset,const void *buf,int size) { +struct stm32mp_bsec_priv *priv =dev_get_priv (dev);int ret =0 ;int i;bool shadow = true, lock = false;int nb_otp = size /sizeof (u32); -int otp; +int otp, cmd;unsigned int offs = offset;if (offs >=STM32_BSEC_LOCK_OFFSET ) {@@ -533,6 +681,19 @@ static int stm32mp_bsec_write(struct udevice *dev, int offset,if ((offs %4 ) || (size %4 ))return -EINVAL ; +if (IS_ENABLED (CONFIG_OPTEE ) && priv->tee) { + cmd =FUSE_ACCESS ; +if (shadow) + cmd =SHADOW_ACCESS ; +if (lock) + cmd =LOCK_ACCESS ; + ret =bsec_optee_pta (dev,PTA_BSEC_WRITE_MEM , cmd, offs, (void *)buf, size); +if (ret) +return ret; + +return size; + } + otp = offs /sizeof (u32);for (i = otp; i < otp + nb_otp && i <=BSEC_OTP_MAX_VALUE ; i++) {@@ -581,6 +742,9 @@ static int stm32mp_bsec_probe(struct udevice *dev)return ret; } +if (IS_ENABLED (CONFIG_OPTEE )) +bsec_optee_open (dev); +/* * update unlocked shadow for OTP cleared by the rom code * only executed in SPL, it is done in TF-A for TFABOOT @@ -607,6 +771,7 @@ U_BOOT_DRIVER(stm32mp_bsec) = { .of_match = stm32mp_bsec_ids, .of_to_plat = stm32mp_bsec_of_to_plat, .plat_auto = sizeof(struct stm32mp_bsec_plat), + .priv_auto = sizeof(struct stm32mp_bsec_priv), .ops = &stm32mp_bsec_ops, .probe = stm32mp_bsec_probe, };arch/arm/mach-stm32mp/cmd_stm32key.c +1
-3@@ -8,6 +8,7 @@#include <console.h> #include <log.h> #include <misc.h> +#include <asm/arch/bsec.h> #include <dm/device.h> #include <dm/uclass.h> @@ -84,9 +85,6 @@ static u32 get_otp_close_mask(void)return STM32_OTP_STM32MP15x_CLOSE_MASK; } -#define BSEC_LOCK_ERROR (-1) -#define BSEC_LOCK_PERM BIT(0) -static int get_misc_dev (struct udevice **dev) {int ret;arch/arm/mach-stm32mp/include/mach/bsec.h +7
-0@@ -5,3 +5,10 @@/* check self hosted debug status = BSEC_DENABLE.DBGSWENABLE */ bool bsec_dbgswenable (void ); + +/* Bitfield definition for LOCK status */ +#define BSEC_LOCK_PERM BIT(30) +#define BSEC_LOCK_SHADOW_R BIT(29) +#define BSEC_LOCK_SHADOW_W BIT(28) +#define BSEC_LOCK_SHADOW_P BIT(27) +#define BSEC_LOCK_ERROR BIT(26)board/st/common/cmd_stboard.c +3
-2@@ -34,6 +34,7 @@#include <command.h> #include <console.h> #include <misc.h> +#include <asm/arch/bsec.h> #include <dm/device.h> #include <dm/uclass.h> @@ -109,7 +110,7 @@ static int do_stboard(struct cmd_tbl *cmdtp, int flag, int argc,else display_stboard (otp);printf (" OTP %d %s locked !\n" ,BSEC_OTP_BOARD , - lock ==1 ?"" :"NOT" ); + lock &BSEC_LOCK_PERM ?"" :"NOT" );return CMD_RET_SUCCESS ; }@@ -178,7 +179,7 @@ static int do_stboard(struct cmd_tbl *cmdtp, int flag, int argc, }/* write persistent lock */ - otp =1 ; + otp =BSEC_LOCK_PERM ; ret =misc_write (dev,STM32_BSEC_LOCK (BSEC_OTP_BOARD ), &otp,sizeof (otp));if (ret !=sizeof (otp)) {doc/board/st/stm32mp1.rst +1
-1@@ -620,7 +620,7 @@ Prerequisite: check if a MAC address isn't yet programmed in OTP STM32MP> env print ethaddr ## Error: "ethaddr" not defined -3) check lock status of fuse 57 & 58 (at 0x39, 0=unlocked, 1=locked):: +3) check lock status of fuse 57 & 58 (at 0x39, 0=unlocked, 0x40000000=locked):: STM32MP> fuse sense 0 0x10000039 2 Sensing bank 0:@@ -640,11 +640,11 @@ Example to set mac address "12:34:56:78:9a:bc" 3) Lock OTP::
doc/board/st/stm32mp1.rst Example to set mac address "12:34:56:78:9a:bc" · line 650
Quoted 10 lines
doc/board/st/stm32mp1.rst +2
-2- STM32MP> fuse prog 0 0x10000039 1 1 + STM32MP> fuse prog 0 0x10000039 0x40000000 0x40000000 STM32MP> fuse sense 0 0x10000039 2 Sensing bank 0: - Word 0x10000039: 00000001 00000001 + Word 0x10000039: 40000000 40000000 4) next REBOOT, in the trace::
Applied to u-boot-stm32/master
Thanks
Patrice
PATCH 3/6 stm32mp: Add support of STM32MP13x in bsec driver
In reply to Patrick DelaunayAdd support for "st,stm32mp13-bsec" for STM32MP13x in the bsec driver based on OP-TEE pseudo TA STM32MP BSEC.
---
arch/arm/mach-stm32mp/bsec.c | 1 + 1 file changed, 1 insertion(+)
arch/arm/mach-stm32mp/bsec.c +1 -0
@@ -761,6 +761,7 @@ static int stm32mp_bsec_probe(struct udevice *dev) }static const struct udevice_id stm32mp_bsec_ids[] = { + { .compatible ="st,stm32mp13-bsec" }, { .compatible ="st,stm32mp15-bsec" }, {} };
Signature · 1 line
2.25.1
Re: [PATCH 3/6] stm32mp: Add support of STM32MP13x in bsec driver
Hi Patrick
Quoted 14 lines · Patrick Delaunay
Add support for "st,stm32mp13-bsec" for STM32MP13x in the bsec driver based on OP-TEE pseudo TA STM32MP BSEC.
Signed-off-by Patrick Delaunay <[email protected]>---
arch/arm/mach-stm32mp/bsec.c | 1 + 1 file changed, 1 insertion(+)arch/arm/mach-stm32mp/bsec.c +0
-0
arch/arm/mach-stm32mp/bsec.c static int stm32mp_bsec_probe(struct udevice *dev) · line 767
Quoted 7 lines
arch/arm/mach-stm32mp/bsec.c +1
-0@@ -761,6 +761,7 @@ static int stm32mp_bsec_probe(struct udevice *dev) }static const struct udevice_id stm32mp_bsec_ids[] = { + { .compatible ="st,stm32mp13-bsec" }, { .compatible ="st,stm32mp15-bsec" }, {} };
Thanks
Patrice
Re: [PATCH 3/6] stm32mp: Add support of STM32MP13x in bsec driver
In reply to Patrick DelaunayHi Patrick
Quoted 14 lines · Patrick Delaunay
Add support for "st,stm32mp13-bsec" for STM32MP13x in the bsec driver based on OP-TEE pseudo TA STM32MP BSEC.
Signed-off-by Patrick Delaunay <[email protected]>---
arch/arm/mach-stm32mp/bsec.c | 1 + 1 file changed, 1 insertion(+)arch/arm/mach-stm32mp/bsec.c +0
-0
arch/arm/mach-stm32mp/bsec.c static int stm32mp_bsec_probe(struct udevice *dev) · line 767
Quoted 7 lines
arch/arm/mach-stm32mp/bsec.c +1
-0@@ -761,6 +761,7 @@ static int stm32mp_bsec_probe(struct udevice *dev) }static const struct udevice_id stm32mp_bsec_ids[] = { + { .compatible ="st,stm32mp13-bsec" }, { .compatible ="st,stm32mp15-bsec" }, {} };
Applied to u-boot-stm32/master
Thanks
Patrice
PATCH 4/6 configs: stm32mp13: Activate CONFIG_CMD_FUSE
In reply to Patrick DelaunayActivate the command fuse to access on STM32MP13x OTP with the BSEC driver.
---
configs/stm32mp13_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/stm32mp13_defconfig +1 -0
@@ -26,6 +26,7 @@ CONFIG_CMD_MEMINFO=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_UNZIP=y CONFIG_CMD_CLK=y +CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_LSBLK=y
Signature · 1 line
2.25.1
Re: [PATCH 4/6] configs: stm32mp13: Activate CONFIG_CMD_FUSE
Hi Patrick
Quoted 14 lines · Patrick Delaunay
Activate the command fuse to access on STM32MP13x OTP with the BSEC driver.
Signed-off-by Patrick Delaunay <[email protected]>---
configs/stm32mp13_defconfig | 1 + 1 file changed, 1 insertion(+)configs/stm32mp13_defconfig +0
-0
configs/stm32mp13_defconfig CONFIG_CMD_MEMINFO=y · line 32
Quoted 7 lines
configs/stm32mp13_defconfig +1
-0@@ -26,6 +26,7 @@ CONFIG_CMD_MEMINFO=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_UNZIP=y CONFIG_CMD_CLK=y +CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_LSBLK=y
Thanks
Patrice
Re: [PATCH 4/6] configs: stm32mp13: Activate CONFIG_CMD_FUSE
In reply to Patrick DelaunayHi Patrick
Quoted 14 lines · Patrick Delaunay
Activate the command fuse to access on STM32MP13x OTP with the BSEC driver.
Signed-off-by Patrick Delaunay <[email protected]>---
configs/stm32mp13_defconfig | 1 + 1 file changed, 1 insertion(+)configs/stm32mp13_defconfig +0
-0
configs/stm32mp13_defconfig CONFIG_CMD_MEMINFO=y · line 32
Quoted 7 lines
configs/stm32mp13_defconfig +1
-0@@ -26,6 +26,7 @@ CONFIG_CMD_MEMINFO=y CONFIG_CMD_MEMTEST=y CONFIG_CMD_UNZIP=y CONFIG_CMD_CLK=y +CONFIG_CMD_FUSE=y CONFIG_CMD_GPIO=y CONFIG_CMD_I2C=y CONFIG_CMD_LSBLK=y
Applied to u-boot-stm32/master
Thanks
Patrice
PATCH 5/6 board: st: Add support of STM32MP13x boards in stm32board cmd
In reply to Patrick DelaunayAdd board identifiers for STMicroelectronics STM32MP13x boards:
- DISCO board: MB1635
---
board/st/common/Kconfig | 2 +- board/st/common/cmd_stboard.c | 7 ++++--- 2 files changed, 5 insertions(+), 4 deletions(-)
board/st/common/Kconfig +1 -1
@@ -1,7 +1,7 @@ config CMD_STBOARD bool "stboard - command for OTP board information" depends on ARCH_STM32MP - default y if TARGET_ST_STM32MP15x + default y if TARGET_ST_STM32MP15x || TARGET_ST_STM32MP13x help This compile the stboard command to read and write the board in the OTP.
board/st/common/cmd_stboard.c +4 -3
@@ -2,8 +2,8 @@/* * Copyright (C) 2019, STMicroelectronics - All Rights Reserved * -* the st command stboard supports the STMicroelectronics board identification -* saved in OTP 59. +* the command stboard supports the STMicroelectronics board identification +* saved in OTP_BOARD. * * The ST product codification have several element * - "Commercial Product Name" (CPN): type of product board (DKX, EVX)
@@ -18,7 +18,7 @@* - Finished Good = EVA32MP157A1$AU1 * * Both information are written on board and these information are also saved -* in OTP59, with: +* in OTP_BOARD (59 for STM32MP15x or 60 for STM32MP13x), with: * bit [31:16] (hex) => Board id, MBxxxx * bit [15:12] (dec) => Variant CPN (1....15) * bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
@@ -49,6 +49,7 @@ static bool check_stboard(u16 board)0x1298 ,0x1341 ,0x1497 , + 0x1635, };for (i =0 ; i <ARRAY_SIZE (st_board_id); i++)
Signature · 1 line
2.25.1
Re: [Uboot-stm32] [PATCH 5/6] board: st: Add support of STM32MP13x boards in stm32board cmd
Hi Patrick
Quoted 48 lines · Patrick Delaunay
Add board identifiers for STMicroelectronics STM32MP13x boards:
- DISCO board: MB1635Signed-off-by Patrick Delaunay <[email protected]>---
board/st/common/Kconfig | 2 +- board/st/common/cmd_stboard.c | 7 ++++--- 2 files changed, 5 insertions(+), 4 deletions(-)board/st/common/Kconfig +1
-1@@ -1,7 +1,7 @@ config CMD_STBOARD bool "stboard - command for OTP board information" depends on ARCH_STM32MP - default y if TARGET_ST_STM32MP15x + default y if TARGET_ST_STM32MP15x || TARGET_ST_STM32MP13x help This compile the stboard command to read and write the board in the OTP.board/st/common/cmd_stboard.c +3
-3@@ -2,8 +2,8 @@/* * Copyright (C) 2019, STMicroelectronics - All Rights Reserved * -* the st command stboard supports the STMicroelectronics board identification -* saved in OTP 59. +* the command stboard supports the STMicroelectronics board identification +* saved in OTP_BOARD. * * The ST product codification have several element * - "Commercial Product Name" (CPN): type of product board (DKX, EVX) @@ -18,7 +18,7 @@* - Finished Good = EVA32MP157A1$AU1 * * Both information are written on board and these information are also saved -* in OTP59, with: +* in OTP_BOARD (59 for STM32MP15x or 60 for STM32MP13x), with: * bit [31:16] (hex) => Board id, MBxxxx * bit [15:12] (dec) => Variant CPN (1....15) * bit [11:8] (dec) => Revision board (index with A = 1, Z = 26)
board/st/common/cmd_stboard.c static bool check_stboard(u16 board) · line 55
Quoted 7 lines
board/st/common/cmd_stboard.c +1
-0@@ -49,6 +49,7 @@ static bool check_stboard(u16 board)0x1298 ,0x1341 ,0x1497 , + 0x1635, };for (i =0 ; i <ARRAY_SIZE (st_board_id); i++)
Thanks
Patrice
Re: [Uboot-stm32] [PATCH 5/6] board: st: Add support of STM32MP13x boards in stm32board cmd
Hi Patrick
Quoted 62 lines · Patrice CHOTARD
Hi Patrick
Quoted 48 lines · Patrick Delaunay
Add board identifiers for STMicroelectronics STM32MP13x boards:
- DISCO board: MB1635Signed-off-by Patrick Delaunay <[email protected]>---
board/st/common/Kconfig | 2 +- board/st/common/cmd_stboard.c | 7 ++++--- 2 files changed, 5 insertions(+), 4 deletions(-)board/st/common/Kconfig +1
-1@@ -1,7 +1,7 @@ config CMD_STBOARD bool "stboard - command for OTP board information" depends on ARCH_STM32MP - default y if TARGET_ST_STM32MP15x + default y if TARGET_ST_STM32MP15x || TARGET_ST_STM32MP13x help This compile the stboard command to read and write the board in the OTP.board/st/common/cmd_stboard.c +3
-3@@ -2,8 +2,8 @@/* * Copyright (C) 2019, STMicroelectronics - All Rights Reserved * -* the st command stboard supports the STMicroelectronics board identification -* saved in OTP 59. +* the command stboard supports the STMicroelectronics board identification +* saved in OTP_BOARD. * * The ST product codification have several element * - "Commercial Product Name" (CPN): type of product board (DKX, EVX) @@ -18,7 +18,7 @@* - Finished Good = EVA32MP157A1$AU1 * * Both information are written on board and these information are also saved -* in OTP59, with: +* in OTP_BOARD (59 for STM32MP15x or 60 for STM32MP13x), with: * bit [31:16] (hex) => Board id, MBxxxx * bit [15:12] (dec) => Variant CPN (1....15) * bit [11:8] (dec) => Revision board (index with A = 1, Z = 26) board/st/common/cmd_stboard.c static bool check_stboard(u16 board) · line 55
Quoted 7 lines
board/st/common/cmd_stboard.c +1
-0@@ -49,6 +49,7 @@ static bool check_stboard(u16 board)0x1298 ,0x1341 ,0x1497 , + 0x1635, };for (i =0 ; i <ARRAY_SIZE (st_board_id); i++)Reviewed-by Patrice Chotard <[email protected]>
Quoted 6 lines
Thanks
Patrice
_______________________________________________
Uboot-stm32 mailing list
[email protected]
https://st-md-mailman.stormreply.com/mailman/listinfo/uboot-stm32
Applied to u-boot-stm32/master
Thanks
Patrice
PATCH 6/6 configs: stm32mp13: Activate command stm32key
In reply to Patrick DelaunayActivate the command stm32key with CONFIG_CMD_STM32KEY.
---
configs/stm32mp13_defconfig | 1 + 1 file changed, 1 insertion(+)
configs/stm32mp13_defconfig +1 -0
@@ -7,6 +7,7 @@ CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dk" CONFIG_SYS_PROMPT="STM32MP> " CONFIG_STM32MP13x=y CONFIG_DDR_CACHEABLE_SIZE=0x10000000 +CONFIG_CMD_STM32KEY=y CONFIG_TARGET_ST_STM32MP13x=y CONFIG_ENV_OFFSET_REDUND=0x940000 # CONFIG_ARMV7_NONSEC is not set
Signature · 1 line
2.25.1
Re: [PATCH 6/6] configs: stm32mp13: Activate command stm32key
Hi Patrick
Quoted 13 lines · Patrick Delaunay
Activate the command stm32key with
CONFIG_CMD_STM32KEY.Signed-off-by Patrick Delaunay <[email protected]>---
configs/stm32mp13_defconfig | 1 + 1 file changed, 1 insertion(+)configs/stm32mp13_defconfig +0
-0
configs/stm32mp13_defconfig CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dk" · line 13
Quoted 7 lines
configs/stm32mp13_defconfig +1
-0@@ -7,6 +7,7 @@ CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dk" CONFIG_SYS_PROMPT="STM32MP> " CONFIG_STM32MP13x=y CONFIG_DDR_CACHEABLE_SIZE=0x10000000 +CONFIG_CMD_STM32KEY=y CONFIG_TARGET_ST_STM32MP13x=y CONFIG_ENV_OFFSET_REDUND=0x940000 # CONFIG_ARMV7_NONSEC is not set
Thanks
Patrice
Re: [PATCH 6/6] configs: stm32mp13: Activate command stm32key
In reply to Patrick DelaunayHi Patrick
Quoted 13 lines · Patrick Delaunay
Activate the command stm32key with
CONFIG_CMD_STM32KEY.Signed-off-by Patrick Delaunay <[email protected]>---
configs/stm32mp13_defconfig | 1 + 1 file changed, 1 insertion(+)configs/stm32mp13_defconfig +0
-0
configs/stm32mp13_defconfig CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dk" · line 13
Quoted 7 lines
configs/stm32mp13_defconfig +1
-0@@ -7,6 +7,7 @@ CONFIG_DEFAULT_DEVICE_TREE="stm32mp135f-dk" CONFIG_SYS_PROMPT="STM32MP> " CONFIG_STM32MP13x=y CONFIG_DDR_CACHEABLE_SIZE=0x10000000 +CONFIG_CMD_STM32KEY=y CONFIG_TARGET_ST_STM32MP13x=y CONFIG_ENV_OFFSET_REDUND=0x940000 # CONFIG_ARMV7_NONSEC is not set
Applied to u-boot-stm32/master
Thanks
Patrice