Skip to contentSkip to conversation

ARM: stm32: Enable bootd, iminfo, imxtract on DHCOM

PATCH New Marek Vasut 2 participants 4 messages Apr 1, 2020 – Apr 24, 2020

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 ARM: stm32: Enable bootd, iminfo, imxtract on DHCOM

Enable these standard U-Boot commands for image manipulation and for starting the default boot command using 'boot' command in U-Boot shell.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 configs/stm32mp15_dhcom_basic_defconfig | 3 ---
 1 file changed, 3 deletions(-)
configs/stm32mp15_dhcom_basic_defconfig +0 -3
index 683f15e7d5..f830feb306 100644
@@ -19,10 +19,7 @@ CONFIG_SPL_MTD_SUPPORT=y
 CONFIG_SPL_POWER_SUPPORT=y
 CONFIG_SYS_SPI_U_BOOT_OFFS=0x80000
 CONFIG_SYS_PROMPT="STM32MP> "
-# CONFIG_CMD_BOOTD is not set
 # CONFIG_CMD_ELF is not set
-# CONFIG_CMD_IMI is not set
-# CONFIG_CMD_XIMG is not set
 # CONFIG_CMD_EXPORTENV is not set
 CONFIG_CMD_EEPROM=y
 CONFIG_CMD_MEMINFO=y
Signature · 1 line
2.25.1
#1 lore raw

PATCH 1/1 ARM: stm32: Enable bootd, iminfo, imxtract on DHCOM

Dear Marek,

Quoted 10 lines

From: Marek Vasut <[email protected]>
Sent: mercredi 1 avril 2020 17:13

Enable these standard U-Boot commands for image manipulation and for starting the default boot command using 'boot' command in U-Boot shell.

Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---

And I think I will done the same patch on ST defconfig.

Thanks

Patrick

#2 lore raw

PATCH 1/1 ARM: stm32: Enable bootd, iminfo, imxtract on DHCOM

Quoted 8 lines · Patrick DELAUNAY

Dear Marek,

Quoted 6 lines

From: Marek Vasut <[email protected]>
Sent: mercredi 1 avril 2020 17:13

Enable these standard U-Boot commands for image manipulation and for starting the default boot command using 'boot' command in U-Boot shell.

Quoted 8 lines
Quoted 4 lines
Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>

---

And I think I will done the same patch on ST defconfig.

Yes please, without this, it was quite annoying on the stm32mp1.

#3 lore raw

PATCH 1/1 ARM: stm32: Enable bootd, iminfo, imxtract on DHCOM

In reply to Marek Vasut

Dear Marek,

Quoted 6 lines

From: Marek Vasut <[email protected]>
Sent: mercredi 1 avril 2020 17:13

Enable these standard U-Boot commands for image manipulation and for starting the default boot command using 'boot' command in U-Boot shell.

Quoted 7 lines
Cc Patrick Delaunay <[email protected]>
Cc Patrice Chotard <[email protected]>
---
 configs/stm32mp15_dhcom_basic_defconfig | 3 ---
 1 file changed, 3 deletions(-)

Applied to u-boot-stm/master, thanks!

Regards

Patrick