USB-> bluetooth adapter problem
I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.
The model is 3CREB96B
Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:
usb 4-1: new full speed USB device using uhci_hcd and address 2hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2
I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.
Can someone please explain this message in more detail (google turns up very little)?
Thanks
Hi Luke,
Quoted 12 lines
I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.
The model is 3CREB96B
Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:
usb 4-1: new full speed USB device using
uhci_hcdand address 2hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2
Quoted 5 lines
I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.
Can someone please explain this message in more detail (google turns up very little)?
try to load the hci_usb driver with "isoc=0". This disables the SCO support inside the driver.
Regards
Marcel
Quoted 20 lines · Marcel Holtmann
Hi Luke,
Quoted 6 lines
I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.
The model is 3CREB96B
Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:
Quoted 9 lines
usb 4-1: new full speed USB device using
uhci_hcdand address 2hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.
Can someone please explain this message in more detail (google turns up very little)?
Quoted 11 lines
try to load the
hci_usbdriver with "isoc=0". This disables the SCO support inside the driver.Regards
Marcel
Thanks for your reply.
Under "Bluetooth subsystem support" I removed support for "SCO links support", and then under "Bluetooth device drivers" I removed SCO (voice) support. What is still left:
HCI USB driver
HCI UART driver
-UART (H4) protocol support
-BCSP protocol support
HCI BCM203x USB driver
HCI BlueFRITZ! USB driver
HCI VHCI (Virtual HCI device) driver
I realize that some of these shouldnt be in there, but I don't think they are causing problems, either. Anyway, after I removed the items mentioned above, and after plugging in the bluetooth adapter, this is what I get:
Oct 9 20:24:17 Obliterus usb 4-1: new full speed USB device using uhci_hcd and address 2 Oct 9 20:24:18 Obliterus usb 4-1: USB disconnect, address 2 Oct 9 20:24:18 Obliterus Bluetooth: HCI USB driver ver 2.8 Oct 9 20:24:18 Obliterus usbcore: registered new driver hci_usb
So it looks like it immediately disconnects. It doesn't show up with lspci at all either. I havent tried using the hci_usb as a module and setting isoc=0 yet, but am I correct that removing the SCO stuff from the kernel took care of the problem, since I no longer get the same message?
Thanks
Hi Luke,
Quoted 23 lines
Under "Bluetooth subsystem support" I removed support for "SCO links support", and then under "Bluetooth device drivers" I removed SCO (voice) support. What is still left:
HCI USB driver
HCI UART driver
-UART (H4) protocol support
-BCSP protocol support
HCI BCM203x USB driver
HCI BlueFRITZ! USB driver
HCI VHCI (Virtual HCI device) driverI realize that some of these shouldnt be in there, but I don't think they are causing problems, either. Anyway, after I removed the items mentioned above, and after plugging in the bluetooth adapter, this is what I get:
Oct 9 20:24:17 Obliterus usb 4-1: new full speed USB device using uhci_hcd and address 2 Oct 9 20:24:18 Obliterus usb 4-1: USB disconnect, address 2 Oct 9 20:24:18 Obliterus Bluetooth: HCI USB driver ver 2.8 Oct 9 20:24:18 Obliterus usbcore: registered new driver hci_usb
Quoted 4 lines
So it looks like it immediately disconnects. It doesn't show up with lspci at all either. I havent tried using the
hci_usbas a module and setting isoc=0 yet, but am I correct that removing the SCO stuff from the kernel took care of the problem, since I no longer get the same message?
build them as modules and do what I told you. Check what lsusb says and what's in /proc/bus/usb/devices. What kernel version are you using?
Regards
Marcel
Quoted 11 lines
Quoted 11 lines
I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.
The model is 3CREB96B
Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:
usb 4-1: new full speed USB device using
uhci_hcdand address 2hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2
Quoted 5 lines
Quoted 5 lines
I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.
Can someone please explain this message in more detail (google turns up very little)?
I got another one of these adapters, and when I plug the new one in I get:
usb 4-1: new full speed USB device using uhci_hcd and address 2
Bluetooth: HCI USB driver ver 2.8
usbcore: registered new driver hci_usb
hcid[30219]: Bluetooth HCI daemon
hcid[30219]: HCI dev 0 up
hcid[30219]: Starting security manager 0
Then I remove that one and plug in the original and get the old problem:
usb 4-1: new full speed USB device using uhci_hcd and address 3 hcid[30219]: HCI dev 0 registered
usb 4-1: USB disconnect, address 3
hcid[1984]: Can't init device hci0: No such device (19 ) hcid[30219]: HCI dev 0 unregistered
So the old one I was using seems to be a bad device, I just want to ask if there are any other possibilities, other than bad hardware, before I get rid of it.
Thanks
Hi Luke,
Quoted 17 lines
I got another one of these adapters, and when I plug the new one in I get:
usb 4-1: new full speed USB device using
uhci_hcdand address 2
Bluetooth: HCI USB driver ver 2.8
usbcore: registered new driverhci_usb
hcid[30219]: Bluetooth HCI daemon
hcid[30219]: HCI dev 0 up
hcid[30219]: Starting security manager 0Then I remove that one and plug in the original and get the old problem:
usb 4-1: new full speed USB device using
uhci_hcdand address 3 hcid[30219]: HCI dev 0 registered
usb 4-1: USB disconnect, address 3
hcid[1984]: Can't init device hci0: No such device (19 ) hcid[30219]: HCI dev 0 unregistered
Quoted 3 lines
So the old one I was using seems to be a bad device, I just want to ask if there are any other possibilities, other than bad hardware, before I get rid of it.
I have no answer to this, but it looks like bad hardware. If you don't wanna return it, you can send the adapter to me for some testing.
Regards
Marcel