Skip to contentSkip to conversation

USB-> bluetooth adapter problem

DISCUSSION Luke Albers 2 participants 6 messages Oct 9, 2005 – Oct 20, 2005

lore
Share & tools
lore
#0 lore raw

I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.

The model is 3CREB96B

Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:

usb 4-1: new full speed USB device using uhci_hcd and address 2
hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2

I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.

Can someone please explain this message in more detail (google turns up very little)?

Thanks

#1 lore raw

Hi Luke,

Quoted 12 lines

I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.

The model is 3CREB96B

Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:

usb 4-1: new full speed USB device using uhci_hcd and address 2
hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2

Quoted 5 lines

I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.

Can someone please explain this message in more detail (google turns up very little)?

try to load the hci_usb driver with "isoc=0". This disables the SCO support inside the driver.

Regards

Marcel

#2 lore raw
Quoted 20 lines · Marcel Holtmann

Hi Luke,

Quoted 6 lines

I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.

The model is 3CREB96B

Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:

Quoted 9 lines

usb 4-1: new full speed USB device using uhci_hcd and address 2
hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2

I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.

Can someone please explain this message in more detail (google turns up very little)?

Quoted 11 lines

try to load the hci_usb driver with "isoc=0". This disables the SCO support inside the driver.

Regards

Marcel

Thanks for your reply.

Under "Bluetooth subsystem support" I removed support for "SCO links support", and then under "Bluetooth device drivers" I removed SCO (voice) support. What is still left:

HCI USB driver
HCI UART driver
-UART (H4) protocol support
-BCSP protocol support
HCI BCM203x USB driver
HCI BlueFRITZ! USB driver
HCI VHCI (Virtual HCI device) driver

I realize that some of these shouldnt be in there, but I don't think they are causing problems, either. Anyway, after I removed the items mentioned above, and after plugging in the bluetooth adapter, this is what I get:

Oct  9 20:24:17 Obliterus usb 4-1: new full speed USB device using uhci_hcd and address 2
Oct  9 20:24:18 Obliterus usb 4-1: USB disconnect, address 2
Oct  9 20:24:18 Obliterus Bluetooth: HCI USB driver ver 2.8
Oct  9 20:24:18 Obliterus usbcore: registered new driver hci_usb

So it looks like it immediately disconnects. It doesn't show up with lspci at all either. I havent tried using the hci_usb as a module and setting isoc=0 yet, but am I correct that removing the SCO stuff from the kernel took care of the problem, since I no longer get the same message?

Thanks

#3 lore raw

Hi Luke,

Quoted 23 lines

Under "Bluetooth subsystem support" I removed support for "SCO links support", and then under "Bluetooth device drivers" I removed SCO (voice) support. What is still left:

HCI USB driver
HCI UART driver
-UART (H4) protocol support
-BCSP protocol support
HCI BCM203x USB driver
HCI BlueFRITZ! USB driver
HCI VHCI (Virtual HCI device) driver

I realize that some of these shouldnt be in there, but I don't think they are causing problems, either. Anyway, after I removed the items mentioned above, and after plugging in the bluetooth adapter, this is what I get:

Oct  9 20:24:17 Obliterus usb 4-1: new full speed USB device using 
uhci_hcd and address 2
Oct  9 20:24:18 Obliterus usb 4-1: USB disconnect, address 2
Oct  9 20:24:18 Obliterus Bluetooth: HCI USB driver ver 2.8
Oct  9 20:24:18 Obliterus usbcore: registered new driver hci_usb
Quoted 4 lines

So it looks like it immediately disconnects. It doesn't show up with lspci at all either. I havent tried using the hci_usb as a module and setting isoc=0 yet, but am I correct that removing the SCO stuff from the kernel took care of the problem, since I no longer get the same message?

build them as modules and do what I told you. Check what lsusb says and what's in /proc/bus/usb/devices. What kernel version are you using?

Regards

Marcel

#4 lore raw
In reply to Marcel Holtmann
Quoted 11 lines
Quoted 11 lines

I have a 3com USB bluetooth adapter, that worked for me at one time, that I can't get working anymore.

The model is 3CREB96B

Sometimes it isnt even noticed when I plug it in, but after restarting hotplug I get this:

usb 4-1: new full speed USB device using uhci_hcd and address 2
hci_usb_probe: Can't set isoc interface settings
usb 4-1: USB disconnect, address 2

Quoted 5 lines
Quoted 5 lines

I don't think that I have removed any options from the kernel that should cause this, and other USB devices work fine.

Can someone please explain this message in more detail (google turns up very little)?

I got another one of these adapters, and when I plug the new one in I get:

usb 4-1: new full speed USB device using uhci_hcd and address 2
Bluetooth: HCI USB driver ver 2.8
usbcore: registered new driver hci_usb
hcid[30219]: Bluetooth HCI daemon
hcid[30219]: HCI dev 0 up
hcid[30219]: Starting security manager 0

Then I remove that one and plug in the original and get the old problem:

usb 4-1: new full speed USB device using uhci_hcd and address 3 hcid[30219]: HCI dev 0 registered
usb 4-1: USB disconnect, address 3
hcid[1984]: Can't init device hci0: No such device (19 ) hcid[30219]: HCI dev 0 unregistered

So the old one I was using seems to be a bad device, I just want to ask if there are any other possibilities, other than bad hardware, before I get rid of it.

Thanks

#5 lore raw

Hi Luke,

Quoted 17 lines

I got another one of these adapters, and when I plug the new one in I get:

usb 4-1: new full speed USB device using uhci_hcd and address 2
Bluetooth: HCI USB driver ver 2.8
usbcore: registered new driver hci_usb
hcid[30219]: Bluetooth HCI daemon
hcid[30219]: HCI dev 0 up
hcid[30219]: Starting security manager 0

Then I remove that one and plug in the original and get the old problem:

usb 4-1: new full speed USB device using uhci_hcd and address 3 hcid[30219]: HCI dev 0 registered
usb 4-1: USB disconnect, address 3
hcid[1984]: Can't init device hci0: No such device (19 ) hcid[30219]: HCI dev 0 unregistered

Quoted 3 lines

So the old one I was using seems to be a bad device, I just want to ask if there are any other possibilities, other than bad hardware, before I get rid of it.

I have no answer to this, but it looks like bad hardware. If you don't wanna return it, you can send the adapter to me for some testing.

Regards

Marcel