Skip to contentSkip to conversation

High load

DISCUSSION Aniruddh Singh 4 participants 10 messages Jan 5, 2006 – Jan 9, 2006

lore
Share & tools
lore
#0 lore raw

HI all,

I have one compaq server with 4 Intel(R) Xeon cpu's (3.1GHZ), 4GB RAM. OS:- Fedora Core 2
Kernel:- 2.6.14

when i compile a new kernel, during th compilation process load goes very high (10 and little above). i can not understand why does this happen, while if i compile the same kernel on my P4 machine with 1GB ram and 3GHZ, it remains under 3.

can somebody tell me what is wrong?
-

Signature · 6 lines
Regards
Aniruddh Singh
System Administrator
Monster.com India Pvt. Ltd.
FC 23, Block B, 1st Floor, Sector 16A
Film City Noida 201301 U.P.
#1 lore raw
Quoted 6 lines · Aniruddh Singh

HI all,

I have one compaq server with 4 Intel(R) Xeon cpu's (3.1GHZ), 4GB RAM. OS:- Fedora Core 2
Kernel:- 2.6.14

Quoted 7 lines

when i compile a new kernel, during th compilation process load goes very high (10 and little above). i can not understand why does this happen, while if i compile the same kernel on my P4 machine with 1GB ram and 3GHZ, it remains under 3.

can somebody tell me what is wrong?
-

Sounds suspiciously like DMA is not working on your drives. Check your dmesg logs and what hdparm returns.

Con

#2 lore raw

Hi,

hdparm -tT /dev/cciss/c0d0p2 returns the following

/dev/cciss/c0d0p2:
Timing buffer-cache reads: 2660 MB in 2.00 seconds = 1329.92 MB/sec
Timing buffered disk reads: 248 MB in 3.00 seconds = 82.55 MB/sec

if i try to hdparm -I /dev/cciss/c0d0 it returns
/dev/cciss/c0d0:
operation not supported on SCSI disks

Do i need to installed sdparm and modify some settings?

Quoted 19 lines · Con Kolivas
Quoted 6 lines · Aniruddh Singh

HI all,

I have one compaq server with 4 Intel(R) Xeon cpu's (3.1GHZ), 4GB RAM. OS:- Fedora Core 2
Kernel:- 2.6.14

Quoted 7 lines

when i compile a new kernel, during th compilation process load goes very high (10 and little above). i can not understand why does this happen, while if i compile the same kernel on my P4 machine with 1GB ram and 3GHZ, it remains under 3.

can somebody tell me what is wrong?
-

Sounds suspiciously like DMA is not working on your drives. Check your dmesg logs and what hdparm returns.

Con

Signature · 6 lines
Regards
Aniruddh Singh
System Administrator
Monster.com India Pvt. Ltd.
FC 23, Block B, 1st Floor, Sector 16A
Film City Noida 201301 U.P.
#3 lore raw
In reply to Con Kolivas

Hi,

there is a raid 0 and raid controller is Smart Array 64xx (rev 01)

hdparm -tT /dev/cciss/c0d0p2 returns the following

/dev/cciss/c0d0p2:
Timing buffer-cache reads: 2660 MB in 2.00 seconds = 1329.92 MB/sec
Timing buffered disk reads: 248 MB in 3.00 seconds = 82.55 MB/sec

if i try to hdparm -I /dev/cciss/c0d0 it returns
/dev/cciss/c0d0:
operation not supported on SCSI disks

Quoted 24 lines · Con Kolivas
Quoted 6 lines · Aniruddh Singh

HI all,

I have one compaq server with 4 Intel(R) Xeon cpu's (3.1GHZ), 4GB RAM. OS:- Fedora Core 2
Kernel:- 2.6.14

Quoted 7 lines

when i compile a new kernel, during th compilation process load goes very high (10 and little above). i can not understand why does this happen, while if i compile the same kernel on my P4 machine with 1GB ram and 3GHZ, it remains under 3.

can somebody tell me what is wrong?
-

Sounds suspiciously like DMA is not working on your drives. Check your dmesg logs and what hdparm returns.

Con
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 6 lines
Regards
Aniruddh Singh
System Administrator
Monster.com India Pvt. Ltd.
FC 23, Block B, 1st Floor, Sector 16A
Film City Noida 201301 U.P.
#4 lore raw
Quoted 5 lines · Aniruddh Singh

Hi,

there is a raid 0 and raid controller is Smart Array 64xx (rev 01)

hdparm -tT /dev/cciss/c0d0p2 returns the following

for measuring IO performance, I'd recommend tiobench over hdparm any day ( http://tiobench.sf.net )

#5 lore raw
Quoted 9 lines · Arjan van de Ven
Quoted 5 lines · Aniruddh Singh

Hi,

there is a raid 0 and raid controller is Smart Array 64xx (rev 01)

hdparm -tT /dev/cciss/c0d0p2 returns the following

for measuring IO performance, I'd recommend tiobench over hdparm any day ( http://tiobench.sf.net )

i will do it, can you please tell me why load goes high when i compile kernel (10 and above)

Quoted 2 lines
Signature · 6 lines
Regards
Aniruddh Singh
System Administrator
Monster.com India Pvt. Ltd.
FC 23, Block B, 1st Floor, Sector 16A
Film City Noida 201301 U.P.
#6 lore raw
Quoted 6 lines · Aniruddh Singh
Quoted 5 lines · Arjan van de Ven
Quoted 4 lines · Aniruddh Singh

Hi,

there is a raid 0 and raid controller is Smart Array 64xx (rev 01)

Quoted 7 lines
Quoted 4 lines
Quoted 1 line

hdparm -tT /dev/cciss/c0d0p2 returns the following

for measuring IO performance, I'd recommend tiobench over hdparm any day ( http://tiobench.sf.net )

i will do it, can you please tell me why load goes high when i compile kernel (10 and above)

thats really odd, unless you do a "make -j", in which case of course it's expected ;)

#7 lore raw
Quoted 9 lines
Quoted 6 lines
Quoted 3 lines

for measuring IO performance, I'd recommend tiobench over hdparm any day ( http://tiobench.sf.net )

i will do it, can you please tell me why load goes high when i compile kernel (10 and above)

thats really odd, unless you do a "make -j", in which case of course it's expected ;)

yes i always use make -j option ??

Signature · 6 lines
Regards
Aniruddh Singh
System Administrator
Monster.com India Pvt. Ltd.
FC 23, Block B, 1st Floor, Sector 16A
Film City Noida 201301 U.P.
#8 lore raw
Quoted 10 lines · On Sat, 07 Jan 2006 11:17:09 +0530 Aniruddh Singh wrote:
Quoted 9 lines
Quoted 6 lines
Quoted 3 lines

for measuring IO performance, I'd recommend tiobench over hdparm any day ( http://tiobench.sf.net )

i will do it, can you please tell me why load goes high when i compile kernel (10 and above)

thats really odd, unless you do a "make -j", in which case of course it's expected ;)

yes i always use make -j option ??

With or without a following integer?

See 'make help':
-j [N], --jobs[=N] Allow N jobs at once; infinite jobs with no arg.

so use make -j N to limit the number of makes/compiles etc. or use 'make -j' to go ballistic.

---
~Randy

#9 lore raw
Quoted 6 lines · Randy.Dunlap
Quoted 4 lines · On Sat, 07 Jan 2006 11:17:09 +0530 Aniruddh Singh wrote:
Quoted 4 lines
Quoted 4 lines
Quoted 3 lines

for measuring IO performance, I'd recommend tiobench over hdparm any day ( http://tiobench.sf.net )

Quoted 8 lines
Quoted 6 lines
Quoted 5 lines
Quoted 2 lines

i will do it, can you please tell me why load goes high when i compile kernel (10 and above)

thats really odd, unless you do a "make -j", in which case of course it's expected ;)

yes i always use make -j option ??

With or without a following integer?

make -j8, machine has 4 processor

Quoted 14 lines

See 'make help':
-j [N], --jobs[=N] Allow N jobs at once; infinite jobs with no arg.

so use make -j N to limit the number of makes/compiles etc. or use 'make -j' to go ballistic.

---
~Randy
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

Signature · 6 lines
Regards
Aniruddh Singh
System Administrator
Monster.com India Pvt. Ltd.
FC 23, Block B, 1st Floor, Sector 16A
Film City Noida 201301 U.P.