Skip to contentSkip to conversation

iozone write 50% regression in kernel 2.6.24-rc1

DISCUSSION Martin Knoblauch 2 participants 2 messages Nov 9, 2007 – Nov 12, 2007

lore
Share & tools
lore
#0 lore raw

----- Original Message ----

Quoted 9 lines

From: "Zhang, Yanmin" <[email protected]>
To: [email protected]
Cc: LKML <[email protected]>
Sent: Friday, November 9, 2007 10:47:52 AM
Subject: iozone write 50% regression in kernel 2.6.24-rc1

Comparing with 2.6.23, iozone sequential write/rewrite (512M) has 50%

regression

Quoted 4 lines

in kernel 2.6.24-rc1. 2.6.24-rc2 has the same regression.

My machine has 8 processor cores and 8GB memory.

Quoted 8 lines

By bisect, I located patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=
04fbfdc14e5f48463820d6b9807daa5e9c92c51f.

Another behavior: with kernel 2.6.23, if I run iozone for many times

after rebooting machine,

Quoted 3 lines

the result looks stable. But with 2.6.24-rc1, the first run of iozone

got a very small result and

Quoted 5 lines

following run has 4Xorig_result.

What I reported is the regression of 2nd/3rd run, because first run has

bigger regression.

Quoted 4 lines

I also tried to change
/proc/sys/vm/dirty_ratio,dirty_backgroud_ratio

and didn't get improvement.

Review

Quoted 3 lines
(quoted diff) +0 -2
-yanmin
-

Hi Yanmin,

could you tell us the exact iozone command you are using? I would like to repeat it on my setup, because I definitely see the opposite behaviour in 2.6.24-rc1/rc2. The speed there is much better than in 2.6.22 and before (I skipped 2.6.23, because I was waiting for the per-bdi changes). I definitely do not see the difference between 1st and subsequent runs. But then, I do my tests with 5GB file sizes like:

iozone3_283/src/current/iozone -t 5 -F /scratch/X1 /scratch/X2 /scratch/X3 /scratch/X4 /scratch/X5 -s 5000M -r 1024 -c -e -i 0 -i 1

Kind regards
Martin

#1 lore raw
Quoted 33 lines · Martin Knoblauch

----- Original Message ----

Quoted 9 lines

From: "Zhang, Yanmin" <[email protected]>
To: [email protected]
Cc: LKML <[email protected]>
Sent: Friday, November 9, 2007 10:47:52 AM
Subject: iozone write 50% regression in kernel 2.6.24-rc1

Comparing with 2.6.23, iozone sequential write/rewrite (512M) has 50%

regression

Quoted 4 lines

in kernel 2.6.24-rc1. 2.6.24-rc2 has the same regression.

My machine has 8 processor cores and 8GB memory.

Quoted 8 lines

By bisect, I located patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=
04fbfdc14e5f48463820d6b9807daa5e9c92c51f.

Another behavior: with kernel 2.6.23, if I run iozone for many times

after rebooting machine,

Quoted 3 lines

the result looks stable. But with 2.6.24-rc1, the first run of iozone

got a very small result and

Quoted 5 lines

following run has 4Xorig_result.

What I reported is the regression of 2nd/3rd run, because first run has

Quoted 7 lines

bigger regression.

Quoted 4 lines

I also tried to change
/proc/sys/vm/dirty_ratio,dirty_backgroud_ratio

and didn't get improvement.
could you tell us the exact iozone command you are using?

iozone -i 0 -r 4k -s 512m

Quoted 3 lines

I would like to repeat it on my setup, because I definitely see the opposite behaviour in 2.6.24-rc1/rc2. The speed there is much better than in 2.6.22 and before (I skipped 2.6.23, because I was waiting for the per-bdi changes). I definitely do not see the difference between 1st and subsequent runs. But then, I do my tests with 5GB file sizes like:

iozone3_283/src/current/iozone -t 5 -F /scratch/X1 /scratch/X2 /scratch/X3 /scratch/X4 /scratch/X5 -s 5000M -r 1024 -c -e -i 0 -i 1

My machine uses SATA (AHCI) disk.

-yanmin