iozone write 50% regression in kernel 2.6.24-rc1
----- Original Message ----
Quoted 9 lines
From: "Zhang, Yanmin" <[email protected]>
To: [email protected]
Cc: LKML <[email protected]>
Sent: Friday, November 9, 2007 10:47:52 AM
Subject: iozone write 50% regression in kernel 2.6.24-rc1Comparing with 2.6.23, iozone sequential write/rewrite (512M) has 50%
regression
Quoted 4 lines
in kernel 2.6.24-rc1. 2.6.24-rc2 has the same regression.
My machine has 8 processor cores and 8GB memory.
Quoted 8 lines
By bisect, I located patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=04fbfdc14e5f48463820d6b9807daa5e9c92c51f.Another behavior: with kernel 2.6.23, if I run iozone for many times
after rebooting machine,
Quoted 3 lines
the result looks stable. But with 2.6.24-rc1, the first run of iozone
got a very small result and
Quoted 5 lines
following run has 4Xorig_result.
What I reported is the regression of 2nd/3rd run, because first run has
bigger regression.
Quoted 4 lines
I also tried to change
/proc/sys/vm/dirty_ratio,dirty_backgroud_ratio
and didn't get improvement.
Review
Quoted 3 lines
(quoted diff) +0
-2-yanmin -
Hi Yanmin,
could you tell us the exact iozone command you are using? I would like to repeat it on my setup, because I definitely see the opposite behaviour in 2.6.24-rc1/rc2. The speed there is much better than in 2.6.22 and before (I skipped 2.6.23, because I was waiting for the per-bdi changes). I definitely do not see the difference between 1st and subsequent runs. But then, I do my tests with 5GB file sizes like:
iozone3_283/src/current/iozone -t 5 -F /scratch/X1 /scratch/X2 /scratch/X3 /scratch/X4 /scratch/X5 -s 5000M -r 1024 -c -e -i 0 -i 1
Kind regards
Martin
Quoted 33 lines · Martin Knoblauch
----- Original Message ----
Quoted 9 lines
From: "Zhang, Yanmin" <[email protected]>
To: [email protected]
Cc: LKML <[email protected]>
Sent: Friday, November 9, 2007 10:47:52 AM
Subject: iozone write 50% regression in kernel 2.6.24-rc1Comparing with 2.6.23, iozone sequential write/rewrite (512M) has 50%
regression
Quoted 4 lines
in kernel 2.6.24-rc1. 2.6.24-rc2 has the same regression.
My machine has 8 processor cores and 8GB memory.
Quoted 8 lines
By bisect, I located patch
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=04fbfdc14e5f48463820d6b9807daa5e9c92c51f.Another behavior: with kernel 2.6.23, if I run iozone for many times
after rebooting machine,
Quoted 3 lines
the result looks stable. But with 2.6.24-rc1, the first run of iozone
got a very small result and
Quoted 5 lines
following run has 4Xorig_result.
What I reported is the regression of 2nd/3rd run, because first run has
Quoted 7 lines
bigger regression.
Quoted 4 lines
I also tried to change
/proc/sys/vm/dirty_ratio,dirty_backgroud_ratioand didn't get improvement.
could you tell us the exact iozone command you are using?
iozone -i 0 -r 4k -s 512m
Quoted 3 lines
I would like to repeat it on my setup, because I definitely see the opposite behaviour in 2.6.24-rc1/rc2. The speed there is much better than in 2.6.22 and before (I skipped 2.6.23, because I was waiting for the per-bdi changes). I definitely do not see the difference between 1st and subsequent runs. But then, I do my tests with 5GB file sizes like:
iozone3_283/src/current/iozone -t 5 -F /scratch/X1 /scratch/X2 /scratch/X3 /scratch/X4 /scratch/X5 -s 5000M -r 1024 -c -e -i 0 -i 1
My machine uses SATA (AHCI) disk.
-yanmin