ath9k: add preliminary support for the AR913x SoCs
v2 cover ath9k: add preliminary support for the AR913x SoCs
This patch set introduces preliminary support for the Atheros' AR9130/AR9132 SoCs built-in WMAC device. Tested with compat-wireless-2009-01-07 and 2.6.27.10 kernel on the following devices:
* Atheros AP83-050 reference board (AR9132 SoC, AR9103 RF)
* TRENDnet TEW-632BRP router (AR9130 SoC, AR9102 RF)
* Mikrotik RB433 board (AR7161 SoC) + AR5416 based miniPCI card
Changes since v1:
* enabling support of the AR9100 has been moved to the end of the series
* bus specific cleanup routine has been rewritten
* PCI code converted to use 'softc.irq' as well
* setup of 'hw->flags' and 'hw->wiphy->interface_modes' has been removed from ath_ahb_probe()
* unregistering of the ath_ahb_diver has been fixed
Changes since RFC:
* bus specific DMA routines removed
* bus specific register access routines removed
* irq value is stored in softc
* rebased against master-2009-01-06 of wireless-testing
11 patches will follow as replies:
Gabor Juhos (11):
ath9k: convert to struct device
ath9k: convert to use bus-agnostic DMA routines
ath9k: introduce bus specific cache size routine
ath9k: introduce bus specific cleanup routine
ath9k: move PCI code into separate file
ath9k: introduce platform driver for AHB bus support
ath9k: get EEPROM contents from platform data on AHB bus
ath9k: remove (u16) casts from rtc register access
ath9k: fix ar5416Addac_9100 values
ath9k: fix null pointer dereference in ani monitor code
ath9k: enable support for AR9100
drivers/net/wireless/ath9k/Makefile | 2 drivers/net/wireless/ath9k/ahb.c | 187 +++++++++++++++++++ drivers/net/wireless/ath9k/ani.c | 6 - drivers/net/wireless/ath9k/beacon.c | 28 +-- drivers/net/wireless/ath9k/core.h | 47 +++++ drivers/net/wireless/ath9k/eeprom.c | 51 ----- drivers/net/wireless/ath9k/hw.c | 17 +- drivers/net/wireless/ath9k/initvals.h | 2 drivers/net/wireless/ath9k/main.c | 326 +++++---------------------------- drivers/net/wireless/ath9k/pci.c | 305 +++++++++++++++++++++++++++++++ drivers/net/wireless/ath9k/recv.c | 24 +- drivers/net/wireless/ath9k/xmit.c | 14 + include/linux/ath9k_platform.h | 28 +++ 13 files changed, 663 insertions(+), 374 deletions(-) create mode 100644 drivers/net/wireless/ath9k/ahb.c create mode 100644 drivers/net/wireless/ath9k/pci.c create mode 100644 include/linux/ath9k_platform.h
PATCH v2 1/11 ath9k: convert to struct device
Convert 'struct pci_dev' to 'struct device' to make it usable on the AHB bus as well.
--- drivers/net/wireless/ath9k/beacon.c | 17 ++++++++++------- drivers/net/wireless/ath9k/core.h | 2 +- drivers/net/wireless/ath9k/main.c | 21 +++++++++++---------- drivers/net/wireless/ath9k/recv.c | 15 +++++++++------ drivers/net/wireless/ath9k/xmit.c | 7 ++++--- 5 files changed, 35 insertions(+), 27 deletions(-)
drivers/net/wireless/ath9k/beacon.c +10 -7
@@ -164,7 +164,7 @@ static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id) bf = avp->av_bcbuf; skb = (struct sk_buff *)bf->bf_mpdu;if (skb) { -pci_unmap_single (sc->pdev, bf->bf_dmacontext, +pci_unmap_single (to_pci_dev (sc->dev), bf->bf_dmacontext, skb->len,PCI_DMA_TODEVICE );dev_kfree_skb_any (skb);
@@ -188,10 +188,11 @@ static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id) } bf->bf_buf_addr = bf->bf_dmacontext = -pci_map_single (sc->pdev, skb->data, +pci_map_single (to_pci_dev (sc->dev), skb->data, skb->len,PCI_DMA_TODEVICE ); -if (unlikely (pci_dma_mapping_error (sc->pdev, bf->bf_buf_addr))) { +if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), + bf->bf_buf_addr))) {dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ; DPRINTF(sc, ATH_DBG_CONFIG,
@@ -343,7 +344,7 @@ int ath_beacon_alloc(struct ath_softc *sc, int if_id) bf = avp->av_bcbuf;if (bf->bf_mpdu !=NULL ) { skb = (struct sk_buff *)bf->bf_mpdu; -pci_unmap_single (sc->pdev, bf->bf_dmacontext, +pci_unmap_single (to_pci_dev (sc->dev), bf->bf_dmacontext, skb->len,PCI_DMA_TODEVICE );dev_kfree_skb_any (skb);
@@ -402,10 +403,11 @@ int ath_beacon_alloc(struct ath_softc *sc, int if_id) bf->bf_mpdu = skb; bf->bf_buf_addr = bf->bf_dmacontext = -pci_map_single (sc->pdev, skb->data, +pci_map_single (to_pci_dev (sc->dev), skb->data, skb->len,PCI_DMA_TODEVICE ); -if (unlikely (pci_dma_mapping_error (sc->pdev, bf->bf_buf_addr))) { +if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), + bf->bf_buf_addr))) {dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ; DPRINTF(sc, ATH_DBG_CONFIG,
@@ -429,7 +431,8 @@ void ath_beacon_return(struct ath_softc *sc, struct ath_vap *avp) bf = avp->av_bcbuf;if (bf->bf_mpdu !=NULL ) {struct sk_buff *skb = (struct sk_buff *)bf->bf_mpdu; -pci_unmap_single (sc->pdev, bf->bf_dmacontext, +pci_unmap_single (to_pci_dev (sc->dev), + bf->bf_dmacontext, skb->len,PCI_DMA_TODEVICE );dev_kfree_skb_any (skb);
drivers/net/wireless/ath9k/core.h +1 -1
@@ -695,7 +695,7 @@ enum PROT_MODE {struct ath_softc {struct ieee80211_hw *hw; -struct pci_dev *pdev; +struct device *dev;struct tasklet_struct intr_tq;struct tasklet_struct bcon_tasklet;struct ath_hal *sc_ah;
drivers/net/wireless/ath9k/main.c +11 -10
@@ -46,7 +46,8 @@ static void bus_read_cachesize(struct ath_softc *sc, int *csz) {u8 u8tmp; -pci_read_config_byte (sc->pdev,PCI_CACHE_LINE_SIZE , (u8 *)&u8tmp); +pci_read_config_byte (to_pci_dev (sc->dev),PCI_CACHE_LINE_SIZE , + (u8 *)&u8tmp); *csz = (int )u8tmp;/*
@@ -1267,11 +1268,11 @@ static int ath_start_rfkill_poll(struct ath_softc *sc)/* Deinitialize the device */ ath_detach (sc); -if (sc->pdev->irq) -free_irq (sc->pdev->irq, sc); -pci_iounmap (sc->pdev, sc->mem); -pci_release_region (sc->pdev,0 ); -pci_disable_device (sc->pdev); +if (to_pci_dev (sc->dev)->irq) +free_irq (to_pci_dev (sc->dev)->irq, sc); +pci_iounmap (to_pci_dev (sc->dev), sc->mem); +pci_release_region (to_pci_dev (sc->dev),0 ); +pci_disable_device (to_pci_dev (sc->dev));ieee80211_free_hw (sc->hw);return -EIO ; }else {
@@ -1708,7 +1709,7 @@ int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd, }/* allocate descriptors */ - dd->dd_desc =pci_alloc_consistent (sc->pdev, + dd->dd_desc =pci_alloc_consistent (to_pci_dev (sc->dev), dd->dd_desc_len, &dd->dd_desc_paddr);if (dd->dd_desc ==NULL ) {
@@ -1756,7 +1757,7 @@ int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd, }return 0 ; fail2: -pci_free_consistent (sc->pdev, +pci_free_consistent (to_pci_dev (sc->dev), dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr); fail:memset (dd,0 ,sizeof (*dd));
@@ -1770,7 +1771,7 @@ void ath_descdma_cleanup(struct ath_softc *sc,struct ath_descdma *dd, struct list_head *head) { - pci_free_consistent(sc->pdev, + pci_free_consistent(to_pci_dev(sc->dev), dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr);INIT_LIST_HEAD (head);
@@ -2615,7 +2616,7 @@ static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) sc = hw->priv; sc->hw = hw; - sc->pdev = pdev; + sc->dev = &pdev->dev; sc->mem = mem;if (ath_attach (id->device, sc) !=0 ) {
drivers/net/wireless/ath9k/recv.c +9 -6
@@ -291,10 +291,11 @@ int ath_rx_init(struct ath_softc *sc, int nbufs) } bf->bf_mpdu = skb; - bf->bf_buf_addr =pci_map_single (sc->pdev, skb->data, + bf->bf_buf_addr =pci_map_single (to_pci_dev (sc->dev), + skb->data, sc->rx.bufsize,PCI_DMA_FROMDEVICE ); -if (unlikely (pci_dma_mapping_error (sc->pdev, +if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), bf->bf_buf_addr))) {dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ;
@@ -524,7 +525,8 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush)* 1. accessing the frame * 2. requeueing the same buffer to h/w */ -pci_dma_sync_single_for_cpu (sc->pdev, bf->bf_buf_addr, +pci_dma_sync_single_for_cpu (to_pci_dev (sc->dev), + bf->bf_buf_addr, sc->rx.bufsize,PCI_DMA_FROMDEVICE );
@@ -557,7 +559,7 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush) goto requeue;/* Unmap the frame */ -pci_unmap_single (sc->pdev, bf->bf_buf_addr, +pci_unmap_single (to_pci_dev (sc->dev), bf->bf_buf_addr, sc->rx.bufsize,PCI_DMA_FROMDEVICE );
@@ -599,10 +601,11 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush)/* We will now give hardware our shiny new allocated skb */ bf->bf_mpdu = requeue_skb; - bf->bf_buf_addr =pci_map_single (sc->pdev, requeue_skb->data, + bf->bf_buf_addr =pci_map_single (to_pci_dev (sc->dev), + requeue_skb->data, sc->rx.bufsize,PCI_DMA_FROMDEVICE ); -if (unlikely (pci_dma_mapping_error (sc->pdev, +if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), bf->bf_buf_addr))) {dev_kfree_skb_any (requeue_skb); bf->bf_mpdu =NULL ;
drivers/net/wireless/ath9k/xmit.c +4 -3
@@ -340,7 +340,7 @@ static void ath_tx_complete_buf(struct ath_softc *sc, }/* Unmap this frame */ -pci_unmap_single (sc->pdev, +pci_unmap_single (to_pci_dev (sc->dev), bf->bf_dmacontext, skb->len,PCI_DMA_TODEVICE );
@@ -1716,9 +1716,10 @@ static int ath_tx_setup_buffer(struct ath_softc *sc, struct ath_buf *bf,/* DMA setup */ bf->bf_mpdu = skb; - bf->bf_dmacontext =pci_map_single (sc->pdev, skb->data, + bf->bf_dmacontext =pci_map_single (to_pci_dev (sc->dev), skb->data, skb->len,PCI_DMA_TODEVICE ); -if (unlikely (pci_dma_mapping_error (sc->pdev, bf->bf_dmacontext))) { +if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), + bf->bf_dmacontext))) { bf->bf_mpdu =NULL ;DPRINTF (sc,ATH_DBG_CONFIG ,"pci_dma_mapping_error() on TX\n" );
Signature · 1 line
1.5.3.2
PATCH v2 2/11 ath9k: convert to use bus-agnostic DMA routines
In reply to Gabor JuhosConvert to use bus-agnostic DMA routines to make it usable on AHB bus as well.
--- drivers/net/wireless/ath9k/beacon.c | 31 ++++++++++++++----------------- drivers/net/wireless/ath9k/main.c | 13 ++++++------- drivers/net/wireless/ath9k/recv.c | 27 ++++++++++++--------------- drivers/net/wireless/ath9k/xmit.c | 15 ++++++--------- 4 files changed, 38 insertions(+), 48 deletions(-)
drivers/net/wireless/ath9k/beacon.c +14 -17
@@ -164,9 +164,9 @@ static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id) bf = avp->av_bcbuf; skb = (struct sk_buff *)bf->bf_mpdu;if (skb) { -pci_unmap_single (to_pci_dev (sc->dev), bf->bf_dmacontext, +dma_unmap_single (sc->dev, bf->bf_dmacontext, skb->len, -PCI_DMA_TODEVICE ); +DMA_TO_DEVICE );dev_kfree_skb_any (skb); }
@@ -188,15 +188,14 @@ static struct ath_buf *ath_beacon_generate(struct ath_softc *sc, int if_id) } bf->bf_buf_addr = bf->bf_dmacontext = -pci_map_single (to_pci_dev (sc->dev), skb->data, +dma_map_single (sc->dev, skb->data, skb->len, -PCI_DMA_TODEVICE ); -if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), - bf->bf_buf_addr))) { +DMA_TO_DEVICE ); +if (unlikely (dma_mapping_error (sc->dev, bf->bf_buf_addr))) {dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ;DPRINTF (sc,ATH_DBG_CONFIG , -"pci_dma_mapping_error() on beaconing\n" ); +"dma_mapping_error() on beaconing\n" );return NULL ; }
@@ -344,9 +343,9 @@ int ath_beacon_alloc(struct ath_softc *sc, int if_id) bf = avp->av_bcbuf;if (bf->bf_mpdu !=NULL ) { skb = (struct sk_buff *)bf->bf_mpdu; -pci_unmap_single (to_pci_dev (sc->dev), bf->bf_dmacontext, +dma_unmap_single (sc->dev, bf->bf_dmacontext, skb->len, -PCI_DMA_TODEVICE ); +DMA_TO_DEVICE );dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ; }
@@ -403,15 +402,14 @@ int ath_beacon_alloc(struct ath_softc *sc, int if_id) bf->bf_mpdu = skb; bf->bf_buf_addr = bf->bf_dmacontext = -pci_map_single (to_pci_dev (sc->dev), skb->data, +dma_map_single (sc->dev, skb->data, skb->len, -PCI_DMA_TODEVICE ); -if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), - bf->bf_buf_addr))) { +DMA_TO_DEVICE ); +if (unlikely (dma_mapping_error (sc->dev, bf->bf_buf_addr))) {dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ;DPRINTF (sc,ATH_DBG_CONFIG , -"pci_dma_mapping_error() on beacon alloc\n" ); +"dma_mapping_error() on beacon alloc\n" );return -ENOMEM ; }
@@ -431,10 +429,9 @@ void ath_beacon_return(struct ath_softc *sc, struct ath_vap *avp) bf = avp->av_bcbuf;if (bf->bf_mpdu !=NULL ) {struct sk_buff *skb = (struct sk_buff *)bf->bf_mpdu; -pci_unmap_single (to_pci_dev (sc->dev), - bf->bf_dmacontext, +dma_unmap_single (sc->dev, bf->bf_dmacontext, skb->len, -PCI_DMA_TODEVICE ); +DMA_TO_DEVICE );dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ; }
drivers/net/wireless/ath9k/main.c +6 -7
@@ -1709,9 +1709,8 @@ int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd, }/* allocate descriptors */ - dd->dd_desc =pci_alloc_consistent (to_pci_dev (sc->dev), - dd->dd_desc_len, - &dd->dd_desc_paddr); + dd->dd_desc =dma_alloc_coherent (sc->dev, dd->dd_desc_len, + &dd->dd_desc_paddr,GFP_ATOMIC );if (dd->dd_desc ==NULL ) { error = -ENOMEM ; goto fail;
@@ -1757,8 +1756,8 @@ int ath_descdma_setup(struct ath_softc *sc, struct ath_descdma *dd, }return 0 ; fail2: -pci_free_consistent (to_pci_dev (sc->dev), - dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr); +dma_free_coherent (sc->dev, dd->dd_desc_len, dd->dd_desc, + dd->dd_desc_paddr); fail:memset (dd,0 ,sizeof (*dd));return error;
@@ -1771,8 +1770,8 @@ void ath_descdma_cleanup(struct ath_softc *sc,struct ath_descdma *dd, struct list_head *head) { - pci_free_consistent(to_pci_dev(sc->dev), - dd->dd_desc_len, dd->dd_desc, dd->dd_desc_paddr); + dma_free_coherent(sc->dev, dd->dd_desc_len, dd->dd_desc, + dd->dd_desc_paddr);INIT_LIST_HEAD (head);kfree (dd->dd_bufptr);
drivers/net/wireless/ath9k/recv.c +12 -15
@@ -291,16 +291,15 @@ int ath_rx_init(struct ath_softc *sc, int nbufs) } bf->bf_mpdu = skb; - bf->bf_buf_addr =pci_map_single (to_pci_dev (sc->dev), - skb->data, + bf->bf_buf_addr =dma_map_single (sc->dev, skb->data, sc->rx.bufsize, -PCI_DMA_FROMDEVICE ); -if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), +DMA_FROM_DEVICE ); +if (unlikely (dma_mapping_error (sc->dev, bf->bf_buf_addr))) {dev_kfree_skb_any (skb); bf->bf_mpdu =NULL ;DPRINTF (sc,ATH_DBG_CONFIG , -"pci_dma_mapping_error() on RX init\n" ); +"dma_mapping_error() on RX init\n" ); error = -ENOMEM ;break ; }
@@ -525,10 +524,9 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush)* 1. accessing the frame * 2. requeueing the same buffer to h/w */ -pci_dma_sync_single_for_cpu (to_pci_dev (sc->dev), - bf->bf_buf_addr, +dma_sync_single_for_cpu (sc->dev, bf->bf_buf_addr, sc->rx.bufsize, -PCI_DMA_FROMDEVICE ); +DMA_FROM_DEVICE );/* * If we're asked to flush receive queue, directly
@@ -559,9 +557,9 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush) goto requeue;/* Unmap the frame */ -pci_unmap_single (to_pci_dev (sc->dev), bf->bf_buf_addr, +dma_unmap_single (sc->dev, bf->bf_buf_addr, sc->rx.bufsize, -PCI_DMA_FROMDEVICE ); +DMA_FROM_DEVICE );skb_put (skb, ds->ds_rxstat.rs_datalen); skb->protocol =cpu_to_be16 (ETH_P_CONTROL );
@@ -601,16 +599,15 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush)/* We will now give hardware our shiny new allocated skb */ bf->bf_mpdu = requeue_skb; - bf->bf_buf_addr =pci_map_single (to_pci_dev (sc->dev), - requeue_skb->data, + bf->bf_buf_addr =dma_map_single (sc->dev, requeue_skb->data, sc->rx.bufsize, -PCI_DMA_FROMDEVICE ); -if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), +DMA_FROM_DEVICE ); +if (unlikely (dma_mapping_error (sc->dev, bf->bf_buf_addr))) {dev_kfree_skb_any (requeue_skb); bf->bf_mpdu =NULL ;DPRINTF (sc,ATH_DBG_CONFIG , -"pci_dma_mapping_error() on RX\n" ); +"dma_mapping_error() on RX\n" );break ; } bf->bf_dmacontext = bf->bf_buf_addr;
drivers/net/wireless/ath9k/xmit.c +6 -9
@@ -340,10 +340,8 @@ static void ath_tx_complete_buf(struct ath_softc *sc, }/* Unmap this frame */ -pci_unmap_single (to_pci_dev (sc->dev), - bf->bf_dmacontext, - skb->len, -PCI_DMA_TODEVICE ); +dma_unmap_single (sc->dev, bf->bf_dmacontext, skb->len,DMA_TO_DEVICE ); +/* complete this frame */ ath_tx_complete (sc, skb, &tx_status);
@@ -1716,13 +1714,12 @@ static int ath_tx_setup_buffer(struct ath_softc *sc, struct ath_buf *bf,/* DMA setup */ bf->bf_mpdu = skb; - bf->bf_dmacontext =pci_map_single (to_pci_dev (sc->dev), skb->data, - skb->len,PCI_DMA_TODEVICE ); -if (unlikely (pci_dma_mapping_error (to_pci_dev (sc->dev), - bf->bf_dmacontext))) { + bf->bf_dmacontext =dma_map_single (sc->dev, skb->data, + skb->len,DMA_TO_DEVICE ); +if (unlikely (dma_mapping_error (sc->dev, bf->bf_dmacontext))) { bf->bf_mpdu =NULL ;DPRINTF (sc,ATH_DBG_CONFIG , -"pci_dma_mapping_error() on TX\n" ); +"dma_mapping_error() on TX\n" );return -ENOMEM ; }
Signature · 1 line
1.5.3.2
PATCH v2 3/11 ath9k: introduce bus specific cache size routine
In reply to Gabor JuhosThe PCI specific bus_read_cachesize routine won't work on the AHB bus, we have to replace it with a suitable one later.
--- drivers/net/wireless/ath9k/core.h | 10 ++++++++++ drivers/net/wireless/ath9k/main.c | 9 +++++++-- 2 files changed, 17 insertions(+), 2 deletions(-)
drivers/net/wireless/ath9k/core.h +10 -0
@@ -693,6 +693,10 @@ enum PROT_MODE {#define SC_OP_RFKILL_SW_BLOCKED BIT(12)#define SC_OP_RFKILL_HW_BLOCKED BIT(13) +struct ath_bus_ops { +void (*read_cachesize)(struct ath_softc *sc,int *csz); +}; +struct ath_softc {struct ieee80211_hw *hw;struct device *dev;
@@ -743,6 +747,7 @@ struct ath_softc {#ifdef CONFIG_ATH9K_DEBUG struct ath9k_debug sc_debug;#endif +struct ath_bus_ops *bus_ops; };int ath_reset (struct ath_softc *sc,bool retry_tx);
@@ -750,4 +755,9 @@ int ath_get_hal_qnum(u16 queue, struct ath_softc *sc);int ath_get_mac80211_qnum (u32 queue,struct ath_softc *sc);int ath_cabq_update (struct ath_softc *); +static inline void ath_read_cachesize (struct ath_softc *sc,int *csz) +{ + sc->bus_ops->read_cachesize (sc, csz); +} +#endif /* CORE_H */
drivers/net/wireless/ath9k/main.c +7 -2
@@ -42,7 +42,7 @@ static void ath_detach(struct ath_softc *sc);/* return bus cachesize in 4B word units */ -static void bus_read_cachesize (struct ath_softc *sc,int *csz) +static void ath_pci_read_cachesize (struct ath_softc *sc,int *csz) {u8 u8tmp;
@@ -1338,7 +1338,7 @@ static int ath_init(u16 devid, struct ath_softc *sc)* Cache line size is used to size and align various * structures used to communicate with the hardware. */ -bus_read_cachesize (sc, &csz); +ath_read_cachesize (sc, &csz);/* XXX assert csz is non-zero */ sc->sc_cachelsz = csz <<2 ;/* convert to bytes */
@@ -2529,6 +2529,10 @@ ath_rf_name(u16 rf_version)return "????" ; } +static struct ath_bus_ops ath_pci_bus_ops = { + .read_cachesize = ath_pci_read_cachesize, +}; +static int ath_pci_probe (struct pci_dev *pdev,const struct pci_device_id *id) {void __iomem *mem;
@@ -2617,6 +2621,7 @@ static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) sc->hw = hw; sc->dev = &pdev->dev; sc->mem = mem; + sc->bus_ops = &ath_pci_bus_ops;if (ath_attach (id->device, sc) !=0 ) { ret = -ENODEV ;
Signature · 1 line
1.5.3.2
PATCH v2 4/11 ath9k: introduce bus specific cleanup routine
In reply to Gabor JuhosWe have left only some PCI specific cleanup code. We have to convert them as well.
--- drivers/net/wireless/ath9k/core.h | 7 +++++++ drivers/net/wireless/ath9k/main.c | 37 +++++++++++++++++++++++-------------- 2 files changed, 30 insertions(+), 14 deletions(-)
drivers/net/wireless/ath9k/core.h +7 -0
@@ -695,6 +695,7 @@ enum PROT_MODE {struct ath_bus_ops {void (*read_cachesize)(struct ath_softc *sc,int *csz); +void (*cleanup)(struct ath_softc *sc); };struct ath_softc {
@@ -704,6 +705,7 @@ struct ath_softc {struct tasklet_struct bcon_tasklet;struct ath_hal *sc_ah;void __iomem *mem; +int irq;spinlock_t sc_resetlock;struct mutex mutex;
@@ -760,4 +762,9 @@ static inline void ath_read_cachesize(struct ath_softc *sc, int *csz) sc->bus_ops->read_cachesize(sc, csz); } +static inline void ath_bus_cleanup (struct ath_softc *sc) +{ + sc->bus_ops->cleanup (sc); +} +#endif /* CORE_H */
drivers/net/wireless/ath9k/main.c +23 -14
@@ -39,6 +39,7 @@ static struct pci_device_id ath_pci_id_table[] __devinitdata = { };static void ath_detach (struct ath_softc *sc); +static void ath_cleanup (struct ath_softc *sc);/* return bus cachesize in 4B word units */
@@ -1267,13 +1268,7 @@ static int ath_start_rfkill_poll(struct ath_softc *sc)rfkill_free (sc->rf_kill.rfkill);/* Deinitialize the device */ -ath_detach (sc); -if (to_pci_dev (sc->dev)->irq) -free_irq (to_pci_dev (sc->dev)->irq, sc); -pci_iounmap (to_pci_dev (sc->dev), sc->mem); -pci_release_region (to_pci_dev (sc->dev),0 ); -pci_disable_device (to_pci_dev (sc->dev)); -ieee80211_free_hw (sc->hw); +ath_cleanup (sc);return -EIO ; }else { sc->sc_flags |=SC_OP_RFKILL_REGISTERED ;
@@ -1284,6 +1279,14 @@ static int ath_start_rfkill_poll(struct ath_softc *sc) }#endif /* CONFIG_RFKILL */ +static void ath_cleanup (struct ath_softc *sc) +{ +ath_detach (sc); +free_irq (sc->irq, sc); +ath_bus_cleanup (sc); +ieee80211_free_hw (sc->hw); +} +static void ath_detach (struct ath_softc *sc) {struct ieee80211_hw *hw = sc->hw;
@@ -2529,8 +2532,18 @@ ath_rf_name(u16 rf_version)return "????" ; } +static void ath_pci_cleanup (struct ath_softc *sc) +{ +struct pci_dev *pdev =to_pci_dev (sc->dev); + +pci_iounmap (pdev, sc->mem); +pci_release_region (pdev,0 ); +pci_disable_device (pdev); +} +static struct ath_bus_ops ath_pci_bus_ops = { .read_cachesize = ath_pci_read_cachesize, + .cleanup = ath_pci_cleanup, };static int ath_pci_probe (struct pci_dev *pdev,const struct pci_device_id *id)
@@ -2637,6 +2650,8 @@ static int ath_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) goto bad4; } + sc->irq = pdev->irq; + ah = sc->sc_ah;printk (KERN_INFO "%s: Atheros AR%s MAC/BB Rev:%x "
@@ -2667,13 +2682,7 @@ static void ath_pci_remove(struct pci_dev *pdev)struct ieee80211_hw *hw =pci_get_drvdata (pdev);struct ath_softc *sc = hw->priv; -ath_detach (sc); -if (pdev->irq) -free_irq (pdev->irq, sc); -pci_iounmap (pdev, sc->mem); -pci_release_region (pdev,0 ); -pci_disable_device (pdev); -ieee80211_free_hw (hw); +ath_cleanup (sc); }#ifdef CONFIG_PM
Signature · 1 line
1.5.3.2
Johannes Berg
maintainerPATCH v2 4/11 ath9k: introduce bus specific cleanup routine
drivers/net/wireless/ath9k/main.c static int ath_start_rfkill_poll(struct ath_softc *sc) · line 1288
Quoted 7 lines · Gabor Juhos
drivers/net/wireless/ath9k/main.c +7
-0+static void ath_cleanup (struct ath_softc *sc) +{ +ath_detach (sc); +free_irq (sc->irq, sc); +ath_bus_cleanup (sc); +ieee80211_free_hw (sc->hw); +}
Umm...
johannes
Johannes Berg
maintainerPATCH v2 4/11 ath9k: introduce bus specific cleanup routine
Quoted 11 lines · Johannes Berg
drivers/net/wireless/ath9k/main.c static int ath_start_rfkill_poll(struct ath_softc *sc) · line 1288
Quoted 7 lines · Gabor Juhos
drivers/net/wireless/ath9k/main.c +7
-0+static void ath_cleanup (struct ath_softc *sc) +{ +ath_detach (sc); +free_irq (sc->irq, sc); +ath_bus_cleanup (sc); +ieee80211_free_hw (sc->hw); +}Umm...
Wait. I got confused, this is ok of course. The original ust had ath_pci_cleanup doing all this. Sorry!
johannes
PATCH v2 5/11 ath9k: move PCI code into separate file
In reply to Gabor JuhosNow that we have converted all bus specific routines to replaceable, we can move the PCI specific codes into a separate file.
--- drivers/net/wireless/ath9k/Makefile | 1 + drivers/net/wireless/ath9k/core.h | 19 ++- drivers/net/wireless/ath9k/main.c | 300 +++-------------------------------- drivers/net/wireless/ath9k/pci.c | 287 +++++++++++++++++++++++++++++++++ 4 files changed, 328 insertions(+), 279 deletions(-)
drivers/net/wireless/ath9k/Makefile +1 -0
@@ -11,6 +11,7 @@ ath9k-y += hw.o \ xmit.o \ rc.o +ath9k-$(CONFIG_PCI) += pci.o ath9k-$(CONFIG_ATH9K_DEBUG) += debug.o obj-$(CONFIG_ATH9K) += ath9k.o
drivers/net/wireless/ath9k/core.h +18 -1
@@ -18,7 +18,7 @@#define CORE_H #include <linux/etherdevice.h> -#include <linux/pci.h> +#include <linux/device.h> #include <net/mac80211.h> #include <linux/leds.h> #include <linux/rfkill.h>
@@ -767,4 +767,21 @@ static inline void ath_bus_cleanup(struct ath_softc *sc) sc->bus_ops->cleanup(sc); } +extern struct ieee80211_ops ath9k_ops; + +irqreturn_t ath_isr (int irq,void *dev); +void ath_cleanup (struct ath_softc *sc); +int ath_attach (u16 devid,struct ath_softc *sc); +void ath_detach (struct ath_softc *sc); +const char *ath_mac_bb_name (u32 mac_bb_version); +const char *ath_rf_name (u16 rf_version); + +#ifdef CONFIG_PCI +int ath_pci_init (void ); +void ath_pci_exit (void ); +#else +static inline int ath_pci_init (void ) {return 0 ; }; +static inline void ath_pci_exit (void ) {}; +#endif +#endif /* CORE_H */
drivers/net/wireless/ath9k/main.c +22 -278
370 lines not on this page · raw message
drivers/net/wireless/ath9k/pci.c new file +287 -0
287 lines not on this page · raw message
Signature · 1 line
1.5.3.2
PATCH v2 6/11 ath9k: introduce platform driver for AHB bus support
In reply to Gabor JuhosThis patch adds the platform_driver itself, and modifies the main driver to register it.
--- drivers/net/wireless/ath9k/Makefile | 1 + drivers/net/wireless/ath9k/ahb.c | 160 +++++++++++++++++++++++++++++++++++ drivers/net/wireless/ath9k/core.h | 8 ++ drivers/net/wireless/ath9k/main.c | 10 ++ 4 files changed, 179 insertions(+), 0 deletions(-)
drivers/net/wireless/ath9k/Makefile +1 -0
@@ -12,6 +12,7 @@ ath9k-y += hw.o \ rc.o ath9k-$(CONFIG_PCI) += pci.o +ath9k-$(CONFIG_ATHEROS_AR71XX) += ahb.o ath9k-$(CONFIG_ATH9K_DEBUG) += debug.o obj-$(CONFIG_ATH9K) += ath9k.o
drivers/net/wireless/ath9k/ahb.c new file +160 -0
160 lines not on this page · raw message
drivers/net/wireless/ath9k/core.h +8 -0
@@ -784,4 +784,12 @@ static inline int ath_pci_init(void) { return 0; };static inline void ath_pci_exit (void ) {};#endif +#ifdef CONFIG_ATHEROS_AR71XX +int ath_ahb_init (void ); +void ath_ahb_exit (void ); +#else +static inline int ath_ahb_init (void ) {return 0 ; }; +static inline void ath_ahb_exit (void ) {}; +#endif +#endif /* CORE_H */
drivers/net/wireless/ath9k/main.c +10 -0
@@ -2522,8 +2522,17 @@ static int __init ath9k_init(void) goto err_rate_unregister; } + error =ath_ahb_init (); +if (error <0 ) { + error = -ENODEV ; + goto err_pci_exit; + } +return 0 ; + err_pci_exit: +ath_pci_exit (); + err_rate_unregister:ath_rate_control_unregister (); err_out:
@@ -2533,6 +2542,7 @@ module_init(ath9k_init); static void __exit ath9k_exit(void) { +ath_ahb_exit ();ath_pci_exit ();ath_rate_control_unregister ();printk (KERN_INFO "%s: Driver unloaded\n" , dev_info);
Signature · 1 line
1.5.3.2
PATCH v2 7/11 ath9k: get EEPROM contents from platform data on AHB bus
In reply to Gabor JuhosOn the AR913x SOCs we have to provide EEPROM contents via platform_data, because accessing the flash via MMIO is not safe. Additionally different boards may store the radio calibration data at different locations.
--- drivers/net/wireless/ath9k/ahb.c | 27 ++++++++++++++++++ drivers/net/wireless/ath9k/core.h | 1 + drivers/net/wireless/ath9k/eeprom.c | 51 ++-------------------------------- drivers/net/wireless/ath9k/pci.c | 18 ++++++++++++ include/linux/ath9k_platform.h | 28 +++++++++++++++++++ 5 files changed, 77 insertions(+), 48 deletions(-)
drivers/net/wireless/ath9k/ahb.c +27 -0
@@ -18,6 +18,7 @@#include <linux/nl80211.h> #include <linux/platform_device.h> +#include <linux/ath9k_platform.h> #include "core.h" #include "reg.h" #include "hw.h"
@@ -33,9 +34,29 @@ static void ath_ahb_cleanup(struct ath_softc *sc)iounmap (sc->mem); } +static bool ath_ahb_eeprom_read (struct ath_hal *ah,u32 off,u16 *data) +{ +struct ath_softc *sc = ah->ah_sc; +struct platform_device *pdev =to_platform_device (sc->dev); +struct ath9k_platform_data *pdata; + + pdata = (struct ath9k_platform_data *) pdev->dev.platform_data; +if (off >= (ARRAY_SIZE (pdata->eeprom_data))) { +DPRINTF (ah->ah_sc,ATH_DBG_FATAL , +"%s: flash read failed, offset %08x is out of range\n" , + __func__, off); +return false; + } + + *data = pdata->eeprom_data[off]; +return true; +} +static struct ath_bus_ops ath_ahb_bus_ops = { .read_cachesize = ath_ahb_read_cachesize, .cleanup = ath_ahb_cleanup, + + .eeprom_read = ath_ahb_eeprom_read, };static int ath_ahb_probe (struct platform_device *pdev)
@@ -48,6 +69,12 @@ static int ath_ahb_probe(struct platform_device *pdev)int ret =0 ;struct ath_hal *ah; +if (!pdev->dev.platform_data) { +dev_err (&pdev->dev,"no platform data specified\n" ); + ret = -EINVAL ; + goto err_out; + } + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (res ==NULL ) {dev_err (&pdev->dev,"no memory resource found\n" );
drivers/net/wireless/ath9k/core.h +1 -0
@@ -696,6 +696,7 @@ enum PROT_MODE {struct ath_bus_ops {void (*read_cachesize)(struct ath_softc *sc,int *csz);void (*cleanup)(struct ath_softc *sc); +bool (*eeprom_read)(struct ath_hal *ah,u32 off,u16 *data); };struct ath_softc {
drivers/net/wireless/ath9k/eeprom.c +3 -48
65 lines not on this page · raw message
drivers/net/wireless/ath9k/pci.c +18 -0
@@ -58,9 +58,27 @@ static void ath_pci_cleanup(struct ath_softc *sc)pci_disable_device (pdev); } +static bool ath_pci_eeprom_read (struct ath_hal *ah,u32 off,u16 *data) +{ + (void )REG_READ (ah,AR5416_EEPROM_OFFSET + (off <<AR5416_EEPROM_S )); + +if (!ath9k_hw_wait (ah, +AR_EEPROM_STATUS_DATA , +AR_EEPROM_STATUS_DATA_BUSY | +AR_EEPROM_STATUS_DATA_PROT_ACCESS ,0 )) { +return false; + } + + *data =MS (REG_READ (ah,AR_EEPROM_STATUS_DATA ), +AR_EEPROM_STATUS_DATA_VAL ); + +return true; +} +static struct ath_bus_ops ath_pci_bus_ops = { .read_cachesize = ath_pci_read_cachesize, .cleanup = ath_pci_cleanup, + .eeprom_read = ath_pci_eeprom_read, };static int ath_pci_probe (struct pci_dev *pdev,const struct pci_device_id *id)
include/linux/ath9k_platform.h new file +28 -0
@@ -0,0 +1,28 @@ +/* +* Copyright (c) 2008 Atheros Communications Inc. +* Copyright (c) 2009 Gabor Juhos <[email protected]> +* Copyright (c) 2009 Imre Kaloz <[email protected]> +* +* Permission to use, copy, modify, and/or distribute this software for any +* purpose with or without fee is hereby granted, provided that the above +* copyright notice and this permission notice appear in all copies. +* +* THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES +* WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF +* MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR +* ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES +* WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN +* ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF +* OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. +*/ + +#ifndef _LINUX_ATH9K_PLATFORM_H +#define _LINUX_ATH9K_PLATFORM_H + +#define ATH9K_PLAT_EEP_MAX_WORDS 2048 + +struct ath9k_platform_data { +u16 eeprom_data[ATH9K_PLAT_EEP_MAX_WORDS ]; +}; + +#endif /* _LINUX_ATH9K_PLATFORM_H */
Signature · 1 line
1.5.3.2
PATCH v2 8/11 ath9k: remove (u16) casts from rtc register access
In reply to Gabor JuhosThe RTC register offsets don't fit into 'u16' on the AR913x, so we have to remove the existing casts.
--- drivers/net/wireless/ath9k/hw.c | 14 +++++++------- 1 files changed, 7 insertions(+), 7 deletions(-)
drivers/net/wireless/ath9k/hw.c +7 -7
@@ -1008,7 +1008,7 @@ static void ath9k_hw_init_pll(struct ath_hal *ah, pll |=SM (0xb ,AR_RTC_PLL_DIV ); } } -REG_WRITE (ah, (u16) (AR_RTC_PLL_CONTROL ), pll); +REG_WRITE (ah, (AR_RTC_PLL_CONTROL ), pll);udelay (RTC_PLL_SETTLE_DELAY );
@@ -1547,11 +1547,11 @@ static bool ath9k_hw_set_reset(struct ath_hal *ah, int type) rst_flags |=AR_RTC_RC_MAC_COLD ; } -REG_WRITE (ah, (u16) (AR_RTC_RC ), rst_flags); +REG_WRITE (ah, (AR_RTC_RC ), rst_flags);udelay (50 ); -REG_WRITE (ah, (u16) (AR_RTC_RC ),0 ); -if (!ath9k_hw_wait (ah, (u16) (AR_RTC_RC ),AR_RTC_RC_M ,0 )) { +REG_WRITE (ah, (AR_RTC_RC ),0 ); +if (!ath9k_hw_wait (ah, (AR_RTC_RC ),AR_RTC_RC_M ,0 )) {DPRINTF (ah->ah_sc,ATH_DBG_RESET ,"RTC stuck in MAC reset\n" );return false;
@@ -1573,8 +1573,8 @@ static bool ath9k_hw_set_reset_power_on(struct ath_hal *ah)REG_WRITE (ah,AR_RTC_FORCE_WAKE ,AR_RTC_FORCE_WAKE_EN |AR_RTC_FORCE_WAKE_ON_INT ); -REG_WRITE (ah, (u16) (AR_RTC_RESET ),0 ); -REG_WRITE (ah, (u16) (AR_RTC_RESET ),1 ); +REG_WRITE (ah, (AR_RTC_RESET ),0 ); +REG_WRITE (ah, (AR_RTC_RESET ),1 ); if (!ath9k_hw_wait(ah, AR_RTC_STATUS,
@@ -2599,7 +2599,7 @@ static void ath9k_set_power_sleep(struct ath_hal *ah, int setChip)if (!AR_SREV_9100 (ah))REG_WRITE (ah,AR_RC ,AR_RC_AHB |AR_RC_HOSTIF ); -REG_CLR_BIT (ah, (u16) (AR_RTC_RESET ), +REG_CLR_BIT (ah, (AR_RTC_RESET ),AR_RTC_RESET_EN ); } }
Signature · 1 line
1.5.3.2
PATCH v2 8/11 ath9k: remove (u16) casts from rtc register access
Quoted 14 lines · Gabor Juhos
The RTC register offsets don't fit into 'u16' on the AR913x, so we have to remove the existing casts.
Signed-off-by Gabor Juhos <[email protected]>Signed-off-by Imre Kaloz <[email protected]>--- drivers/net/wireless/ath9k/hw.c | 14 +++++++------- 1 files changed, 7 insertions(+), 7 deletions(-)drivers/net/wireless/ath9k/hw.c +0
-0
drivers/net/wireless/ath9k/hw.c static void ath9k_hw_init_pll(struct ath_hal *ah, · line 1011
Quoted 5 lines
drivers/net/wireless/ath9k/hw.c +1
-1@@ -1008,7 +1008,7 @@ static void ath9k_hw_init_pll(struct ath_hal *ah, pll |=SM (0xb ,AR_RTC_PLL_DIV ); } } -REG_WRITE (ah, (u16) (AR_RTC_PLL_CONTROL ), pll); +REG_WRITE (ah, (AR_RTC_PLL_CONTROL ), pll);
Perhaps you could remove the parentheses as well? It looks weird otherwise.
Signature · 2 lines
Regards, Pavel Roskin
PATCH v2 8/11 ath9k: remove (u16) casts from rtc register access
Pavel Roskin ?rta:
Quoted 10 lines · Gabor Juhos
Quoted 9 lines
The RTC register offsets don't fit into 'u16' on the AR913x, so we have to remove the existing casts.
Signed-off-by Gabor Juhos <[email protected]>Signed-off-by Imre Kaloz <[email protected]>--- drivers/net/wireless/ath9k/hw.c | 14 +++++++------- 1 files changed, 7 insertions(+), 7 deletions(-)
Quoted 14 lines
drivers/net/wireless/ath9k/hw.c static void ath9k_hw_init_pll(struct ath_hal *ah, · line 1011
Quoted 10 lines
drivers/net/wireless/ath9k/hw.c +1
-1@@ -1008,7 +1008,7 @@ static void ath9k_hw_init_pll(struct ath_hal *ah, pll |=SM (0xb ,AR_RTC_PLL_DIV ); } } -REG_WRITE (ah, (u16) (AR_RTC_PLL_CONTROL ), pll); +REG_WRITE (ah, (AR_RTC_PLL_CONTROL ), pll);Perhaps you could remove the parentheses as well? It looks weird otherwise.
Yes. I will do it.
PATCH v2 9/11 ath9k: fix ar5416Addac_9100 values
In reply to Gabor JuhosWriting the register at offset 0x98c4 causes a deadlock on the AR913x SoCs. Although i don't have detailed knowledge about these registers, but if i change the register offset according to the 'ar5416Addac' table, it works. Additionally there is no reference to the 0x98c4 elsewhere.
--- drivers/net/wireless/ath9k/initvals.h | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
drivers/net/wireless/ath9k/initvals.h +1 -1
@@ -658,7 +658,7 @@ static const u32 ar5416Addac_9100[][2] = { {0x0000989c, 0x00000000 }, {0x0000989c, 0x00000000 }, {0x0000989c, 0x00000000 }, - {0x000098c4, 0x00000000 }, + {0x000098cc, 0x00000000 }, }; static const u32 ar5416Modes[][6] = {
Signature · 1 line
1.5.3.2
PATCH v2 10/11 ath9k: fix null pointer dereference in ani monitor code
In reply to Gabor JuhosIn 'ath9k_ani_reset' the 'ahp->ah_curani' will be initialized only if 'DO_ANI(ah)' true. In 'ath9k_hw_ani_monitor' we are using 'ahp->ah_curani' unconditionally, and it will cause a NULL pointer dereference on AR9100.
--- drivers/net/wireless/ath9k/ani.c | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-)
drivers/net/wireless/ath9k/ani.c +3 -3
@@ -551,6 +551,9 @@ void ath9k_hw_ani_monitor(struct ath_hal *ah,struct ar5416AniState *aniState;int32_t listenTime; +if (!DO_ANI (ah)) +return ; + aniState = ahp->ah_curani; ahp->ah_stats.ast_nodestats = *stats;
@@ -610,9 +613,6 @@ void ath9k_hw_ani_monitor(struct ath_hal *ah, aniState->cckPhyErrCount = cckPhyErrCnt; } -if (!DO_ANI (ah)) -return ; -if (aniState->listenTime >5 * ahp->ah_aniPeriod) { if (aniState->ofdmPhyErrCount <= aniState->listenTime * aniState->ofdmTrigLow / 1000 &&
Signature · 1 line
1.5.3.2
PATCH v2 11/11 ath9k: enable support for AR9100
In reply to Gabor JuhosBecause we have support for the AR9100 devices now, we can enable them.
--- drivers/net/wireless/ath9k/hw.c | 3 +++ 1 files changed, 3 insertions(+), 0 deletions(-)
drivers/net/wireless/ath9k/hw.c +3 -0
@@ -373,6 +373,8 @@ static const char *ath9k_hw_devname(u16 devid)return "Atheros 5418" ;case AR9160_DEVID_PCI :return "Atheros 9160" ; +case AR5416_AR9100_DEVID : +return "Atheros 9100" ;case AR9280_DEVID_PCI :case AR9280_DEVID_PCIE :return "Atheros 9280" ;
@@ -1176,6 +1178,7 @@ struct ath_hal *ath9k_hw_attach(u16 devid, struct ath_softc *sc,switch (devid) {case AR5416_DEVID_PCI :case AR5416_DEVID_PCIE : +case AR5416_AR9100_DEVID :case AR9160_DEVID_PCI :case AR9280_DEVID_PCI :case AR9280_DEVID_PCIE :
Signature · 1 line
1.5.3.2