qong: support for Dave/DENX QongEVB-LITE
Subsystems (3)
v3 cover qong: support for Dave/DENX QongEVB-LITE
These patches add support for Dave/DENX QongEVB-LITE i.MX31-based board.
PATCH v3 1/3 mx31: add GPIO registers definitions
Added definitions for i.MX31 processor GPIO registers.
--- include/asm-arm/arch-mx31/mx31-regs.h | 10 ++++++++++ 1 files changed, 10 insertions(+), 0 deletions(-)
include/asm-arm/arch-mx31/mx31-regs.h +10 -0
@@ -87,6 +87,16 @@#define WDOG_BASE 0x53FDC000/* +* GPIO +*/ +#define GPIO1_BASE 0x53FCC000 +#define GPIO2_BASE 0x53FD0000 +#define GPIO3_BASE 0x53FA4000 +#define GPIO_DR 0x00000000/* data register */ +#define GPIO_GDIR 0x00000004/* direction register */ +#define GPIO_PSR 0x00000008/* pad status register */ + +/* * Signal Multiplexing (IOMUX) */
Signature · 1 line
1.6.0.6
PATCH v3 1/3 mx31: add GPIO registers definitions
Quoted 4 lines · Ilya Yanok
Added definitions for i.MX31 processor GPIO registers.
Signed-off-by Ilya Yanok <[email protected]>---
applied to u-boot-arm
Best Regards,
J.
PATCH v3 2/3 dnet: driver for Dave DNET ethernet controller
In reply to Ilya YanokDriver for Dave DNET ethernet controller (used on Dave/DENX QongEVB-LITE board).
--- drivers/net/Makefile | 2 + drivers/net/dnet.c | 396 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/dnet.h | 166 +++++++++++++++++++++ include/netdev.h | 1 + 4 files changed, 565 insertions(+), 0 deletions(-) create mode 100644 drivers/net/dnet.c create mode 100644 drivers/net/dnet.h
drivers/net/Makefile +2 -0
@@ -33,6 +33,7 @@ COBJS-$(CONFIG_BFIN_MAC) += bfin_mac.o COBJS-$(CONFIG_DRIVER_CS8900) += cs8900.o COBJS-$(CONFIG_TULIP) += dc2114x.o COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o +COBJS-$(CONFIG_DNET) += dnet.o COBJS-$(CONFIG_E1000) += e1000.o COBJS-$(CONFIG_EEPRO100) += eepro100.o COBJS-$(CONFIG_ENC28J60) += enc28j60.o
@@ -69,6 +70,7 @@ COBJS-$(CONFIG_ULI526X) += uli526x.o COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o COBJS-$(CONFIG_XILINX_EMAC) += xilinx_emac.o COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o +COBJS-$(CONFIG_SH_ETHER) += sh_eth.o COBJS := $(COBJS-y) SRCS := $(COBJS:.o=.c)
drivers/net/dnet.c new file +396 -0
396 lines not on this page · raw message
drivers/net/dnet.h new file +166 -0
166 lines not on this page · raw message
include/netdev.h +1 -0
@@ -44,6 +44,7 @@ int cpu_eth_init(bd_t *bis);int au1x00_enet_initialize (bd_t *);int bfin_EMAC_initialize (bd_t *bis);int dc21x4x_initialize (bd_t *bis); +int dnet_eth_initialize (int id,void *regs,unsigned int phy_addr);int e1000_initialize (bd_t *bis);int eepro100_initialize (bd_t *bis);int eth_3com_initialize (bd_t * bis);
Signature · 1 line
1.6.0.6
PATCH v3 2/3 dnet: driver for Dave DNET ethernet controller
Hi Ilya,
This looks much better.
Quoted 5 lines · Ilya Yanok
Driver for Dave DNET ethernet controller (used on Dave/DENX QongEVB-LITE board).
Signed-off-by Ilya Yanok <[email protected]>
<snip>
Quoted 22 lines
--- drivers/net/Makefile | 2 + drivers/net/dnet.c | 396 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/dnet.h | 166 +++++++++++++++++++++ include/netdev.h | 1 + 4 files changed, 565 insertions(+), 0 deletions(-) create mode 100644 drivers/net/dnet.c create mode 100644 drivers/net/dnet.hdrivers/net/Makefile +1
-0@@ -33,6 +33,7 @@ COBJS-$(CONFIG_BFIN_MAC) += bfin_mac.o COBJS-$(CONFIG_DRIVER_CS8900) += cs8900.o COBJS-$(CONFIG_TULIP) += dc2114x.o COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o +COBJS-$(CONFIG_DNET) += dnet.o COBJS-$(CONFIG_E1000) += e1000.o COBJS-$(CONFIG_EEPRO100) += eepro100.o COBJS-$(CONFIG_ENC28J60) += enc28j60.o
drivers/net/Makefile COBJS-$(CONFIG_ULI526X) += uli526x.o · line 74
Quoted 5 lines
drivers/net/Makefile +1
-0@@ -69,6 +70,7 @@ COBJS-$(CONFIG_ULI526X) += uli526x.o COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o COBJS-$(CONFIG_XILINX_EMAC) += xilinx_emac.o COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o +COBJS-$(CONFIG_SH_ETHER) += sh_eth.o
Why is the SH driver affected?, or is this a merge artifact?
<snip>
Quoted 45 lines
drivers/net/Makefile +44
-0+struct dnet_registers { + /* ALL DNET FIFO REGISTERS */ + u32 RX_LEN_FIFO; + u32 RX_DATA_FIFO; + u32 TX_LEN_FIFO; + u32 TX_DATA_FIFO; + u32 pad1[0x3c]; + /* ALL DNET CONTROL/STATUS REGISTERS */ + u32 VERCAPS; + u32 INTR_SRC; + u32 INTR_ENB; + u32 RX_STATUS; + u32 TX_STATUS; + u32 RX_FRAMES_CNT; + u32 TX_FRAMES_CNT; + u32 RX_FIFO_TH; + u32 TX_FIFO_TH; + u32 SYS_CTL; + u32 PAUSE_TMR; + u32 RX_FIFO_WCNT; + u32 TX_FIFO_WCNT; + u32 pad2[0x33]; + /* ALL DNET MAC REGISTERS */ + u32 MACREG_DATA; /* Mac-Reg Data */ + u32 MACREG_ADDR; /* Mac-Reg Addr */ + u32 pad3[0x3e]; + /* ALL DNET RX STATISTICS COUNTERS */ + u32 RX_PKT_IGNR_CNT; + u32 RX_LEN_CHK_ERR_CNT; + u32 RX_LNG_FRM_CNT; + u32 RX_SHRT_FRM_CNT; + u32 RX_IPG_VIOL_CNT; + u32 RX_CRC_ERR_CNT; + u32 RX_OK_PKT_CNT; + u32 RX_CTL_FRM_CNT; + u32 RX_PAUSE_FRM_CNT; + u32 RX_MULTICAST_CNT; + u32 RX_BROADCAST_CNT; + u32 RX_VLAN_TAG_CNT; + u32 RX_PRE_SHRINK_CNT; + u32 RX_DRIB_NIB_CNT; + u32 RX_UNSUP_OPCD_CNT; + u32 RX_BYTE_CNT; + u32 pad4[0x30];
drivers/net/Makefile COBJS-$(CONFIG_ULI526X) += uli526x.o
Quoted 10 lines
drivers/net/Makefile +10
-0+ /* DNET TX STATISTICS COUNTERS */ + u32 TX_UNICAST_CNT; + u32 TX_PAUSE_FRM_CNT; + u32 TX_MULTICAST_CNT; + u32 TX_BRDCAST_CNT; + u32 TX_VLAN_TAG_CNT; + u32 TX_BAD_FCS_CNT; + u32 TX_JUMBO_CNT; + u32 TX_BYTE_CNT; +} __attribute__((packed));
Why is this packed? All fields are 32-bit aligned already.
Quoted 103 lines
drivers/net/Makefile +97
-0+ +/* SOME INTERNAL MAC-CORE REGISTER */ +#define DNET_INTERNAL_MODE_REG 0x0 +#define DNET_INTERNAL_RXTX_CONTROL_REG 0x2 +#define DNET_INTERNAL_MAX_PKT_SIZE_REG 0x4 +#define DNET_INTERNAL_IGP_REG 0x8 +#define DNET_INTERNAL_MAC_ADDR_0_REG 0xa +#define DNET_INTERNAL_MAC_ADDR_1_REG 0xc +#define DNET_INTERNAL_MAC_ADDR_2_REG 0xe +#define DNET_INTERNAL_TX_RX_STS_REG 0x12 +#define DNET_INTERNAL_GMII_MNG_CTL_REG 0x14 +#define DNET_INTERNAL_GMII_MNG_DAT_REG 0x16 + +#define DNET_INTERNAL_GMII_MNG_CMD_FIN (1 << 14) + +#define DNET_INTERNAL_WRITE (1 << 31) + +/* MAC-CORE REGISTER FIELDS */ + +/* MAC-CORE MODE REGISTER FIELDS */ +#define DNET_INTERNAL_MODE_GBITEN (1 << 0) +#define DNET_INTERNAL_MODE_FCEN (1 << 1) +#define DNET_INTERNAL_MODE_RXEN (1 << 2) +#define DNET_INTERNAL_MODE_TXEN (1 << 3) + +/* MAC-CORE RXTX CONTROL REGISTER FIELDS */ +#define DNET_INTERNAL_RXTX_CONTROL_RXSHORTFRAME (1 << 8) +#define DNET_INTERNAL_RXTX_CONTROL_RXBROADCAST (1 << 7) +#define DNET_INTERNAL_RXTX_CONTROL_RXMULTICAST (1 << 4) +#define DNET_INTERNAL_RXTX_CONTROL_RXPAUSE (1 << 3) +#define DNET_INTERNAL_RXTX_CONTROL_DISTXFCS (1 << 2) +#define DNET_INTERNAL_RXTX_CONTROL_DISCFXFCS (1 << 1) +#define DNET_INTERNAL_RXTX_CONTROL_ENPROMISC (1 << 0) +#define DNET_INTERNAL_RXTX_CONTROL_DROPCONTROL (1 << 6) +#define DNET_INTERNAL_RXTX_CONTROL_ENABLEHALFDUP (1 << 5) + +/* SYSTEM CONTROL REGISTER FIELDS */ +#define DNET_SYS_CTL_IGNORENEXTPKT (1 << 0) +#define DNET_SYS_CTL_SENDPAUSE (1 << 2) +#define DNET_SYS_CTL_RXFIFOFLUSH (1 << 3) +#define DNET_SYS_CTL_TXFIFOFLUSH (1 << 4) + +/* TX STATUS REGISTER FIELDS */ +#define DNET_TX_STATUS_FIFO_ALMOST_EMPTY (1 << 2) +#define DNET_TX_STATUS_FIFO_ALMOST_FULL (1 << 1) + +/* INTERRUPT SOURCE REGISTER FIELDS */ +#define DNET_INTR_SRC_TX_PKTSENT (1 << 0) +#define DNET_INTR_SRC_TX_FIFOAF (1 << 1) +#define DNET_INTR_SRC_TX_FIFOAE (1 << 2) +#define DNET_INTR_SRC_TX_DISCFRM (1 << 3) +#define DNET_INTR_SRC_TX_FIFOFULL (1 << 4) +#define DNET_INTR_SRC_RX_CMDFIFOAF (1 << 8) +#define DNET_INTR_SRC_RX_CMDFIFOFF (1 << 9) +#define DNET_INTR_SRC_RX_DATAFIFOFF (1 << 10) +#define DNET_INTR_SRC_TX_SUMMARY (1 << 16) +#define DNET_INTR_SRC_RX_SUMMARY (1 << 17) +#define DNET_INTR_SRC_PHY (1 << 19) + +/* INTERRUPT ENABLE REGISTER FIELDS */ +#define DNET_INTR_ENB_TX_PKTSENT (1 << 0) +#define DNET_INTR_ENB_TX_FIFOAF (1 << 1) +#define DNET_INTR_ENB_TX_FIFOAE (1 << 2) +#define DNET_INTR_ENB_TX_DISCFRM (1 << 3) +#define DNET_INTR_ENB_TX_FIFOFULL (1 << 4) +#define DNET_INTR_ENB_RX_PKTRDY (1 << 8) +#define DNET_INTR_ENB_RX_FIFOAF (1 << 9) +#define DNET_INTR_ENB_RX_FIFOERR (1 << 10) +#define DNET_INTR_ENB_RX_ERROR (1 << 11) +#define DNET_INTR_ENB_RX_FIFOFULL (1 << 12) +#define DNET_INTR_ENB_RX_FIFOAE (1 << 13) +#define DNET_INTR_ENB_TX_SUMMARY (1 << 16) +#define DNET_INTR_ENB_RX_SUMMARY (1 << 17) +#define DNET_INTR_ENB_GLOBAL_ENABLE (1 << 18) + +/* + * Capabilities. Used by the driver to know the capabilities that + * the ethernet controller inside the FPGA have. + */ + +#define DNET_HAS_MDIO (1 << 0) +#define DNET_HAS_IRQ (1 << 1) +#define DNET_HAS_GIGABIT (1 << 2) +#define DNET_HAS_DMA (1 << 3) + +#define DNET_HAS_MII (1 << 4) /* or GMII */ +#define DNET_HAS_RMII (1 << 5) /* or RGMII */ + +#define DNET_CAPS_MASK 0xFFFF + +#define DNET_FIFO_SIZE 2048 /* 2K x 32 bit */ +#define DNET_FIFO_TX_DATA_AF_TH (DNET_FIFO_SIZE - 384) /* 384 = 1536 / 4 */ +#define DNET_FIFO_TX_DATA_AE_TH (384) + +#define DNET_FIFO_RX_CMD_AF_TH (1 << 16) /* just one frame inside the FIFO */ + +#endifinclude/netdev.h +0
-0
include/netdev.h int cpu_eth_init(bd_t *bis); · line 50
Quoted 7 lines
include/netdev.h +1
-0@@ -44,6 +44,7 @@ int cpu_eth_init(bd_t *bis);int au1x00_enet_initialize (bd_t *);int bfin_EMAC_initialize (bd_t *bis);int dc21x4x_initialize (bd_t *bis); +int dnet_eth_initialize (int id,void *regs,unsigned int phy_addr);int e1000_initialize (bd_t *bis);int eepro100_initialize (bd_t *bis);int eth_3com_initialize (bd_t * bis);
regards,
Ben
PATCH v3 2/3 dnet: driver for Dave DNET ethernet controller
Hi Ben,
thanks for review.
Quoted 7 lines · Ben Warren
drivers/net/Makefile COBJS-$(CONFIG_ULI526X) += uli526x.o · line 74
Quoted 6 lines
drivers/net/Makefile +1
-0@@ -69,6 +70,7 @@ COBJS-$(CONFIG_ULI526X) += uli526x.o COBJS-$(CONFIG_VSC7385_ENET) += vsc7385.o COBJS-$(CONFIG_XILINX_EMAC) += xilinx_emac.o COBJS-$(CONFIG_XILINX_EMACLITE) += xilinx_emaclite.o +COBJS-$(CONFIG_SH_ETHER) += sh_eth.oWhy is the SH driver affected?, or is this a merge artifact?
Uh... Sorry. Yes, it's merge artifact.
Quoted 49 lines
<snip>
Quoted 48 lines
drivers/net/dnet.h new file +48
-0+struct dnet_registers { +/* ALL DNET FIFO REGISTERS */ +u32 RX_LEN_FIFO; +u32 RX_DATA_FIFO; +u32 TX_LEN_FIFO; +u32 TX_DATA_FIFO; +u32 pad1[0x3c ]; +/* ALL DNET CONTROL/STATUS REGISTERS */ +u32 VERCAPS; +u32 INTR_SRC; +u32 INTR_ENB; +u32 RX_STATUS; +u32 TX_STATUS; +u32 RX_FRAMES_CNT; +u32 TX_FRAMES_CNT; +u32 RX_FIFO_TH; +u32 TX_FIFO_TH; +u32 SYS_CTL; +u32 PAUSE_TMR; +u32 RX_FIFO_WCNT; +u32 TX_FIFO_WCNT; +u32 pad2[0x33 ]; +/* ALL DNET MAC REGISTERS */ +u32 MACREG_DATA;/* Mac-Reg Data */ +u32 MACREG_ADDR;/* Mac-Reg Addr */ +u32 pad3[0x3e ]; +/* ALL DNET RX STATISTICS COUNTERS */ +u32 RX_PKT_IGNR_CNT; +u32 RX_LEN_CHK_ERR_CNT; +u32 RX_LNG_FRM_CNT; +u32 RX_SHRT_FRM_CNT; +u32 RX_IPG_VIOL_CNT; +u32 RX_CRC_ERR_CNT; +u32 RX_OK_PKT_CNT; +u32 RX_CTL_FRM_CNT; +u32 RX_PAUSE_FRM_CNT; +u32 RX_MULTICAST_CNT; +u32 RX_BROADCAST_CNT; +u32 RX_VLAN_TAG_CNT; +u32 RX_PRE_SHRINK_CNT; +u32 RX_DRIB_NIB_CNT; +u32 RX_UNSUP_OPCD_CNT; +u32 RX_BYTE_CNT; +u32 pad4[0x30 ]; +/* DNET TX STATISTICS COUNTERS */ +u32 TX_UNICAST_CNT; +u32 TX_PAUSE_FRM_CNT; +u32 TX_MULTICAST_CNT;
Quoted 8 lines
drivers/net/dnet.h line 69
Quoted 7 lines
drivers/net/dnet.h new file +6
-0+u32 TX_BRDCAST_CNT ; +u32 TX_VLAN_TAG_CNT ; +u32 TX_BAD_FCS_CNT ; +u32 TX_JUMBO_CNT ; +u32 TX_BYTE_CNT ; +} __attribute__((packed));Why is this packed? All fields are 32-bit aligned already.
Generally, I prefer declaring such structures with ((packed)) regardless of if it's really do something. Just to show that it should be packed.
Regards, Ilya.
PATCH v3 2/3 dnet: driver for Dave DNET ethernet controller
Dear Ilya,
Quoted 1 line · In message <[email protected]> you wrote:
...
Quoted 8 lines
Quoted 5 lines
drivers/net/dnet.h line 69
Quoted 4 lines
drivers/net/dnet.h new file +3
-0+u32 TX_JUMBO_CNT ; +u32 TX_BYTE_CNT ; +} __attribute__((packed));Why is this packed? All fields are 32-bit aligned already.
Generally, I prefer declaring such structures with ((packed)) regardless of if it's really do something. Just to show that it should be packed.
Can you please verify that it works as well without the "packed", and if it does (as expected) resubmit without it?
Thanks.
Best regards,
Wolfgang Denk
Signature · 4 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Drawing on my fine command of language, I said nothing.
PATCH v3 2/3 dnet: driver for Dave DNET ethernet controller
Hi Wolfgang,
Quoted 5 lines · Wolfgang Denk
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
drivers/net/dnet.h new file +3
-0+u32 TX_JUMBO_CNT ; +u32 TX_BYTE_CNT ; +} __attribute__((packed));
Quoted 9 lines
Quoted 5 lines
Quoted 2 lines
Why is this packed? All fields are 32-bit aligned already.
Generally, I prefer declaring such structures with ((packed)) regardless of if it's really do something. Just to show that it should be packed.
Can you please verify that it works as well without the "packed", and if it does (as expected) resubmit without it?
Ok. It works as expected. I'll post the updated patch soon.
Regards, Ilya.
PATCH v4 2/3 dnet: driver for Dave DNET ethernet controller
In reply to Wolfgang DenkDriver for Dave DNET ethernet controller (used on Dave/DENX QongEVB-LITE board).
--- drivers/net/Makefile | 1 + drivers/net/dnet.c | 396 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/dnet.h | 166 +++++++++++++++++++++ include/netdev.h | 1 + 4 files changed, 564 insertions(+), 0 deletions(-) create mode 100644 drivers/net/dnet.c create mode 100644 drivers/net/dnet.h
drivers/net/Makefile +1 -0
@@ -33,6 +33,7 @@ COBJS-$(CONFIG_BFIN_MAC) += bfin_mac.o COBJS-$(CONFIG_DRIVER_CS8900) += cs8900.o COBJS-$(CONFIG_TULIP) += dc2114x.o COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o +COBJS-$(CONFIG_DNET) += dnet.o COBJS-$(CONFIG_E1000) += e1000.o COBJS-$(CONFIG_EEPRO100) += eepro100.o COBJS-$(CONFIG_ENC28J60) += enc28j60.o
drivers/net/dnet.c new file +396 -0
396 lines not on this page · raw message
drivers/net/dnet.h new file +166 -0
166 lines not on this page · raw message
include/netdev.h +1 -0
@@ -44,6 +44,7 @@ int cpu_eth_init(bd_t *bis);int au1x00_enet_initialize (bd_t *);int bfin_EMAC_initialize (bd_t *bis);int dc21x4x_initialize (bd_t *bis); +int dnet_eth_initialize (int id,void *regs,unsigned int phy_addr);int e1000_initialize (bd_t *bis);int eepro100_initialize (bd_t *bis);int eth_3com_initialize (bd_t * bis);
Signature · 1 line
1.6.0.6
PATCH v3 2/3 dnet: driver for Dave DNET ethernet controller
In reply to Wolfgang DenkHello All,
Sorry guys, it looks like I posted the wrong version. Please discard [v4] patch. I'll post [v5] version soon.
Regards, Ilya.
PATCH v5 2/3 dnet: driver for Dave DNET ethernet controller
In reply to Wolfgang DenkDriver for Dave DNET ethernet controller (used on Dave/DENX QongEVB-LITE board).
--- drivers/net/Makefile | 1 + drivers/net/dnet.c | 396 ++++++++++++++++++++++++++++++++++++++++++++++++++ drivers/net/dnet.h | 166 +++++++++++++++++++++ include/netdev.h | 1 + 4 files changed, 564 insertions(+), 0 deletions(-) create mode 100644 drivers/net/dnet.c create mode 100644 drivers/net/dnet.h
drivers/net/Makefile +1 -0
@@ -33,6 +33,7 @@ COBJS-$(CONFIG_BFIN_MAC) += bfin_mac.o COBJS-$(CONFIG_DRIVER_CS8900) += cs8900.o COBJS-$(CONFIG_TULIP) += dc2114x.o COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o +COBJS-$(CONFIG_DNET) += dnet.o COBJS-$(CONFIG_E1000) += e1000.o COBJS-$(CONFIG_EEPRO100) += eepro100.o COBJS-$(CONFIG_ENC28J60) += enc28j60.o
drivers/net/dnet.c new file +396 -0
396 lines not on this page · raw message
drivers/net/dnet.h new file +166 -0
166 lines not on this page · raw message
include/netdev.h +1 -0
@@ -44,6 +44,7 @@ int cpu_eth_init(bd_t *bis);int au1x00_enet_initialize (bd_t *);int bfin_EMAC_initialize (bd_t *bis);int dc21x4x_initialize (bd_t *bis); +int dnet_eth_initialize (int id,void *regs,unsigned int phy_addr);int e1000_initialize (bd_t *bis);int eepro100_initialize (bd_t *bis);int eth_3com_initialize (bd_t * bis);
Signature · 1 line
1.6.0.6
PATCH v5 2/3 dnet: driver for Dave DNET ethernet controller
Quoted 5 lines · Ilya Yanok
Driver for Dave DNET ethernet controller (used on Dave/DENX QongEVB-LITE board).
Signed-off-by Ilya Yanok <[email protected]>---
Ben If it's ok with you I'll apply it at the same time of the board
Best Regards,
J.
PATCH v5 2/3 dnet: driver for Dave DNET ethernet controller
Quoted 5 lines · Jean-Christophe PLAGNIOL-VILLARD
Quoted 3 lines · Ilya Yanok
Driver for Dave DNET ethernet controller (used on Dave/DENX QongEVB-LITE board).
Quoted 8 lines
Quoted 3 lines
Signed-off-by Ilya Yanok <[email protected]>---
Ben If it's ok with you I'll apply it at the same time of the board
Best Regards,
J.
PATCH v3 3/3 qong: support for Dave/DENX QongEVB-LITE board
In reply to Ilya YanokThis patch adds support for Dave/DENX QongEVB-LITE i.MX31-based board.
--- MAINTAINERS | 3 + MAKEALL | 1 + Makefile | 4 + board/davedenx/qong/Makefile | 53 +++++++++ board/davedenx/qong/config.mk | 1 + board/davedenx/qong/lowlevel_init.S | 172 ++++++++++++++++++++++++++++ board/davedenx/qong/qong.c | 168 +++++++++++++++++++++++++++ board/davedenx/qong/qong_fpga.h | 41 +++++++ board/davedenx/qong/u-boot.lds | 58 ++++++++++ include/configs/qong.h | 215 +++++++++++++++++++++++++++++++++++ 10 files changed, 716 insertions(+), 0 deletions(-) create mode 100644 board/davedenx/qong/Makefile create mode 100644 board/davedenx/qong/config.mk create mode 100644 board/davedenx/qong/lowlevel_init.S create mode 100644 board/davedenx/qong/qong.c create mode 100644 board/davedenx/qong/qong_fpga.h create mode 100644 board/davedenx/qong/u-boot.lds create mode 100644 include/configs/qong.h
MAINTAINERS +3 -0
@@ -655,6 +655,9 @@ Sergey Lapin <[email protected]> afeb9260 ARM926EJS (AT91SAM9260 SoC) +Wolfgang Denk <[email protected]> + qong i.MX31 + ------------------------------------------------------------------------- Unknown / orphaned boards:
MAKEALL +1 -0
@@ -542,6 +542,7 @@ LIST_ARM11=" \ imx31_litekit \ imx31_phycore \ mx31ads \ + qong \ smdk6400 \ "
Makefile +4 -0
@@ -3034,6 +3034,10 @@ mx31ads_config : unconfig omap2420h4_config : unconfig @$(MKCONFIG) $(@:_config=) arm arm1136 omap2420h4 NULL omap24xx +qong_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm1136 qong davedenx mx31 + + ######################################################################### ## ARM1176 Systems #########################################################################
board/davedenx/qong/Makefile new file +53 -0
53 lines not on this page · raw message
board/davedenx/qong/config.mk new file +1 -0
@@ -0,0 +1 @@ +TEXT_BASE = 0x8ff00000
board/davedenx/qong/lowlevel_init.S new file +172 -0
172 lines not on this page · raw message
board/davedenx/qong/qong.c new file +168 -0
168 lines not on this page · raw message
board/davedenx/qong/qong_fpga.h new file +41 -0
41 lines not on this page · raw message
board/davedenx/qong/u-boot.lds new file +58 -0
58 lines not on this page · raw message
include/configs/qong.h new file +215 -0
215 lines not on this page · raw message
Signature · 1 line
1.6.0.6
v3 cover qong: support for Dave/DENX QongEVB-LITE
In reply to Ilya YanokQuoted 4 lines · Ilya Yanok
These patches add support for Dave/DENX QongEVB-LITE i.MX31-based board.
Signed-off-by Ilya Yanok <[email protected]>
applied to u-boot-arm
Best Regards,
J.