Skip to contentSkip to conversation

tulip: Fix for MTU problems with 802.1q tagged frames

PATCH Applied Ivan Vecera 5 participants 5 messages Mar 5, 2009 – Mar 13, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 tulip: Fix for MTU problems with 802.1q tagged frames

The original patch was submitted last year but wasn't discussed or applied because of missing maintainer's CCs. I only fixed some formatting errors, but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We should allow receiving frames of up to 1518 bytes in length, instead of 1514.

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Tested on D-Link DFE-570TX quad-fastethernet card.

---
 drivers/net/tulip/interrupt.c |   84 +++++++++++++++++++++++++++--------------
 drivers/net/tulip/tulip.h     |   32 +++++++++++++++-
 2 files changed, 86 insertions(+), 30 deletions(-)
drivers/net/tulip/interrupt.c +55 -29
index 6c3428a..c21193b 100644
@@ -140,6 +140,7 @@ int tulip_poll(struct napi_struct *napi, int budget)
                /* If we own the next entry, it is a new packet. Send it up. */
                while ( ! (tp->rx_ring[entry].status & cpu_to_le32(DescOwned))) {
                        s32 status = le32_to_cpu(tp->rx_ring[entry].status);
+		       short pkt_len;
 
                        if (tp->dirty_rx + RX_RING_SIZE == tp->cur_rx)
                                break;
@@ -151,8 +152,28 @@ int tulip_poll(struct napi_struct *napi, int budget)
 		       if (++work_done >= budget)
                                goto not_done;
 
-                       if ((status & 0x38008300) != 0x0300) {
-                               if ((status & 0x38000300) != 0x0300) {
+		       /*
+			* Omit the four octet CRC from the length.
+			* (May not be considered valid until we have
+			* checked status for RxLengthOver2047 bits)
+			*/
+		       pkt_len = ((status >> 16) & 0x7ff) - 4;
+
+		       /*
+			* Maximum pkt_len is 1518 (1514 + vlan header)
+			* Anything higher than this is always invalid
+			* regardless of RxLengthOver2047 bits
+			*/
+
+		       if ((status & (RxLengthOver2047 |
+				      RxDescCRCError |
+				      RxDescCollisionSeen |
+				      RxDescRunt |
+				      RxDescDescErr |
+				      RxWholePkt)) != RxWholePkt
+			   || pkt_len > 1518) {
+			       if ((status & (RxLengthOver2047 |
+					      RxWholePkt)) != RxWholePkt) {
                                 /* Ingore earlier buffers. */
                                        if ((status & 0xffff) != 0x7fff) {
                                                if (tulip_debug > 1)
@@ -161,30 +182,23 @@ int tulip_poll(struct napi_struct *napi, int budget)
                                                               dev->name, status);
                                                tp->stats.rx_length_errors++;
                                        }
-                               } else if (status & RxDescFatalErr) {
+			       } else {
                                 /* There was a fatal error. */
                                        if (tulip_debug > 2)
                                                printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
                                                       dev->name, status);
                                        tp->stats.rx_errors++; /* end of a packet.*/
-                                       if (status & 0x0890) tp->stats.rx_length_errors++;
+				       if (pkt_len > 1518 ||
+					   (status & RxDescRunt))
+					       tp->stats.rx_length_errors++;
+
                                        if (status & 0x0004) tp->stats.rx_frame_errors++;
                                        if (status & 0x0002) tp->stats.rx_crc_errors++;
                                        if (status & 0x0001) tp->stats.rx_fifo_errors++;
                                }
                        } else {
-                               /* Omit the four octet CRC from the length. */
-                               short pkt_len = ((status >> 16) & 0x7ff) - 4;
                                struct sk_buff *skb;
 
-#ifndef final_version
-                               if (pkt_len > 1518) {
-                                       printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
-                                              dev->name, pkt_len, pkt_len);
-                                       pkt_len = 1518;
-                                       tp->stats.rx_length_errors++;
-                               }
-#endif
                                /* Check if the packet is long enough to accept without copying
                                   to a minimally-sized skbuff. */
                                if (pkt_len < tulip_rx_copybreak
@@ -356,14 +370,35 @@ static int tulip_rx(struct net_device *dev)
 	/* If we own the next entry, it is a new packet. Send it up. */
 	while ( ! (tp->rx_ring[entry].status & cpu_to_le32(DescOwned))) {
 		s32 status = le32_to_cpu(tp->rx_ring[entry].status);
+		short pkt_len;
 
 		if (tulip_debug > 5)
 			printk(KERN_DEBUG "%s: In tulip_rx(), entry %d %8.8x.\n",
 				   dev->name, entry, status);
 		if (--rx_work_limit < 0)
 			break;
-		if ((status & 0x38008300) != 0x0300) {
-			if ((status & 0x38000300) != 0x0300) {
+
+		/*
+		  Omit the four octet CRC from the length.
+		  (May not be considered valid until we have
+		  checked status for RxLengthOver2047 bits)
+		*/
+		pkt_len = ((status >> 16) & 0x7ff) - 4;
+		/*
+		  Maximum pkt_len is 1518 (1514 + vlan header)
+		  Anything higher than this is always invalid
+		  regardless of RxLengthOver2047 bits
+		*/
+
+		if ((status & (RxLengthOver2047 |
+			       RxDescCRCError |
+			       RxDescCollisionSeen |
+			       RxDescRunt |
+			       RxDescDescErr |
+			       RxWholePkt))        != RxWholePkt
+		     || pkt_len > 1518) {
+			if ((status & (RxLengthOver2047 |
+			     RxWholePkt))         != RxWholePkt) {
 				/* Ingore earlier buffers. */
 				if ((status & 0xffff) != 0x7fff) {
 					if (tulip_debug > 1)
@@ -372,31 +407,22 @@ static int tulip_rx(struct net_device *dev)
 							   dev->name, status);
 					tp->stats.rx_length_errors++;
 				}
-			} else if (status & RxDescFatalErr) {
+			} else {
 				/* There was a fatal error. */
 				if (tulip_debug > 2)
 					printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
 						   dev->name, status);
 				tp->stats.rx_errors++; /* end of a packet.*/
-				if (status & 0x0890) tp->stats.rx_length_errors++;
+				if (pkt_len > 1518 ||
+				    (status & RxDescRunt))
+					tp->stats.rx_length_errors++;
 				if (status & 0x0004) tp->stats.rx_frame_errors++;
 				if (status & 0x0002) tp->stats.rx_crc_errors++;
 				if (status & 0x0001) tp->stats.rx_fifo_errors++;
 			}
 		} else {
-			/* Omit the four octet CRC from the length. */
-			short pkt_len = ((status >> 16) & 0x7ff) - 4;
 			struct sk_buff *skb;
 
-#ifndef final_version
-			if (pkt_len > 1518) {
-				printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
-					   dev->name, pkt_len, pkt_len);
-				pkt_len = 1518;
-				tp->stats.rx_length_errors++;
-			}
-#endif
-
 			/* Check if the packet is long enough to accept without copying
 			   to a minimally-sized skbuff. */
 			if (pkt_len < tulip_rx_copybreak
drivers/net/tulip/tulip.h +31 -1
index 19abbc3..0afa2d4 100644
@@ -201,8 +201,38 @@ enum desc_status_bits {
 	DescStartPkt = 0x20000000,
 	DescEndRing  = 0x02000000,
 	DescUseLink  = 0x01000000,
-	RxDescFatalErr = 0x008000,
+
+	/*
+	 * Error summary flag is logical or of 'CRC Error', 'Collision Seen',
+	 * 'Frame Too Long', 'Runt' and 'Descriptor Error' flags generated
+	 * within tulip chip.
+	 */
+	RxDescErrorSummary = 0x8000,
+	RxDescCRCError = 0x0002,
+	RxDescCollisionSeen = 0x0040,
+
+	/*
+	 * 'Frame Too Long' flag is set if packet length including CRC exceeds
+	 * 1518.  However, a full sized VLAN tagged frame is 1522 bytes
+	 * including CRC.
+	 *
+	 * The tulip chip does not block oversized frames, and if this flag is
+	 * set on a receive descriptor it does not indicate the frame has been
+	 * truncated.  The receive descriptor also includes the actual length.
+	 * Therefore we can safety ignore this flag and check the length
+	 * ourselves.
+	 */
+	RxDescFrameTooLong = 0x0080,
+	RxDescRunt = 0x0800,
+	RxDescDescErr = 0x4000,
 	RxWholePkt   = 0x00000300,
+	/*
+	 * Top three bits of 14 bit frame length (status bits 27-29) should
+	 * never be set as that would make frame over 2047 bytes. The Receive
+	 * Watchdog flag (bit 4) may indicate the length is over 2048 and the
+	 * length field is invalid.
+	 */
+	RxLengthOver2047 = 0x38000010
 };
 
 
Signature · 1 line
1.6.0.4
#1 lore raw
Quoted 9 lines · Ivan Vecera

The original patch was submitted last year but wasn't discussed or applied because of missing maintainer's CCs. I only fixed some formatting errors, but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We should allow receiving frames of up to 1518 bytes in length, instead of 1514.

Quoted 8 lines

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Tested on D-Link DFE-570TX quad-fastethernet card.

Looks good. FWIW:

Acked-by on v1 1/1
#2 lore raw
In reply to Ivan Vecera
Quoted 9 lines · Ivan Vecera

The original patch was submitted last year but wasn't discussed or applied because of missing maintainer's CCs. I only fixed some formatting errors, but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We should allow receiving frames of up to 1518 bytes in length, instead of 1514.

Quoted 8 lines

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Tested on D-Link DFE-570TX quad-fastethernet card.

I reviewed this earlier in the week (offlist email) and it looks fine to me too.

And while I agree the white space isn't uhm, "optimal", I didn't feel it was worthwhile to generate a massive white space diff.

thanks,
grant

Quoted 204 lines
---
 drivers/net/tulip/interrupt.c |   84 +++++++++++++++++++++++++++--------------
 drivers/net/tulip/tulip.h     |   32 +++++++++++++++-
 2 files changed, 86 insertions(+), 30 deletions(-)
drivers/net/tulip/interrupt.c +55 -29
index 6c3428a..c21193b 100644
@@ -140,6 +140,7 @@ int tulip_poll(struct napi_struct *napi, int budget)
                /* If we own the next entry, it is a new packet. Send it up. */
                while ( ! (tp->rx_ring[entry].status & cpu_to_le32(DescOwned))) {
                        s32 status = le32_to_cpu(tp->rx_ring[entry].status);
+		       short pkt_len;
 
                        if (tp->dirty_rx + RX_RING_SIZE == tp->cur_rx)
                                break;
@@ -151,8 +152,28 @@ int tulip_poll(struct napi_struct *napi, int budget)
 		       if (++work_done >= budget)
                                goto not_done;
 
-                       if ((status & 0x38008300) != 0x0300) {
-                               if ((status & 0x38000300) != 0x0300) {
+		       /*
+			* Omit the four octet CRC from the length.
+			* (May not be considered valid until we have
+			* checked status for RxLengthOver2047 bits)
+			*/
+		       pkt_len = ((status >> 16) & 0x7ff) - 4;
+
+		       /*
+			* Maximum pkt_len is 1518 (1514 + vlan header)
+			* Anything higher than this is always invalid
+			* regardless of RxLengthOver2047 bits
+			*/
+
+		       if ((status & (RxLengthOver2047 |
+				      RxDescCRCError |
+				      RxDescCollisionSeen |
+				      RxDescRunt |
+				      RxDescDescErr |
+				      RxWholePkt)) != RxWholePkt
+			   || pkt_len > 1518) {
+			       if ((status & (RxLengthOver2047 |
+					      RxWholePkt)) != RxWholePkt) {
                                 /* Ingore earlier buffers. */
                                        if ((status & 0xffff) != 0x7fff) {
                                                if (tulip_debug > 1)
@@ -161,30 +182,23 @@ int tulip_poll(struct napi_struct *napi, int budget)
                                                               dev->name, status);
                                                tp->stats.rx_length_errors++;
                                        }
-                               } else if (status & RxDescFatalErr) {
+			       } else {
                                 /* There was a fatal error. */
                                        if (tulip_debug > 2)
                                                printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
                                                       dev->name, status);
                                        tp->stats.rx_errors++; /* end of a packet.*/
-                                       if (status & 0x0890) tp->stats.rx_length_errors++;
+				       if (pkt_len > 1518 ||
+					   (status & RxDescRunt))
+					       tp->stats.rx_length_errors++;
+
                                        if (status & 0x0004) tp->stats.rx_frame_errors++;
                                        if (status & 0x0002) tp->stats.rx_crc_errors++;
                                        if (status & 0x0001) tp->stats.rx_fifo_errors++;
                                }
                        } else {
-                               /* Omit the four octet CRC from the length. */
-                               short pkt_len = ((status >> 16) & 0x7ff) - 4;
                                struct sk_buff *skb;
 
-#ifndef final_version
-                               if (pkt_len > 1518) {
-                                       printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
-                                              dev->name, pkt_len, pkt_len);
-                                       pkt_len = 1518;
-                                       tp->stats.rx_length_errors++;
-                               }
-#endif
                                /* Check if the packet is long enough to accept without copying
                                   to a minimally-sized skbuff. */
                                if (pkt_len < tulip_rx_copybreak
@@ -356,14 +370,35 @@ static int tulip_rx(struct net_device *dev)
 	/* If we own the next entry, it is a new packet. Send it up. */
 	while ( ! (tp->rx_ring[entry].status & cpu_to_le32(DescOwned))) {
 		s32 status = le32_to_cpu(tp->rx_ring[entry].status);
+		short pkt_len;
 
 		if (tulip_debug > 5)
 			printk(KERN_DEBUG "%s: In tulip_rx(), entry %d %8.8x.\n",
 				   dev->name, entry, status);
 		if (--rx_work_limit < 0)
 			break;
-		if ((status & 0x38008300) != 0x0300) {
-			if ((status & 0x38000300) != 0x0300) {
+
+		/*
+		  Omit the four octet CRC from the length.
+		  (May not be considered valid until we have
+		  checked status for RxLengthOver2047 bits)
+		*/
+		pkt_len = ((status >> 16) & 0x7ff) - 4;
+		/*
+		  Maximum pkt_len is 1518 (1514 + vlan header)
+		  Anything higher than this is always invalid
+		  regardless of RxLengthOver2047 bits
+		*/
+
+		if ((status & (RxLengthOver2047 |
+			       RxDescCRCError |
+			       RxDescCollisionSeen |
+			       RxDescRunt |
+			       RxDescDescErr |
+			       RxWholePkt))        != RxWholePkt
+		     || pkt_len > 1518) {
+			if ((status & (RxLengthOver2047 |
+			     RxWholePkt))         != RxWholePkt) {
 				/* Ingore earlier buffers. */
 				if ((status & 0xffff) != 0x7fff) {
 					if (tulip_debug > 1)
@@ -372,31 +407,22 @@ static int tulip_rx(struct net_device *dev)
 							   dev->name, status);
 					tp->stats.rx_length_errors++;
 				}
-			} else if (status & RxDescFatalErr) {
+			} else {
 				/* There was a fatal error. */
 				if (tulip_debug > 2)
 					printk(KERN_DEBUG "%s: Receive error, Rx status %8.8x.\n",
 						   dev->name, status);
 				tp->stats.rx_errors++; /* end of a packet.*/
-				if (status & 0x0890) tp->stats.rx_length_errors++;
+				if (pkt_len > 1518 ||
+				    (status & RxDescRunt))
+					tp->stats.rx_length_errors++;
 				if (status & 0x0004) tp->stats.rx_frame_errors++;
 				if (status & 0x0002) tp->stats.rx_crc_errors++;
 				if (status & 0x0001) tp->stats.rx_fifo_errors++;
 			}
 		} else {
-			/* Omit the four octet CRC from the length. */
-			short pkt_len = ((status >> 16) & 0x7ff) - 4;
 			struct sk_buff *skb;
 
-#ifndef final_version
-			if (pkt_len > 1518) {
-				printk(KERN_WARNING "%s: Bogus packet size of %d (%#x).\n",
-					   dev->name, pkt_len, pkt_len);
-				pkt_len = 1518;
-				tp->stats.rx_length_errors++;
-			}
-#endif
-
 			/* Check if the packet is long enough to accept without copying
 			   to a minimally-sized skbuff. */
 			if (pkt_len < tulip_rx_copybreak
drivers/net/tulip/tulip.h +31 -1
index 19abbc3..0afa2d4 100644
@@ -201,8 +201,38 @@ enum desc_status_bits {
 	DescStartPkt = 0x20000000,
 	DescEndRing  = 0x02000000,
 	DescUseLink  = 0x01000000,
-	RxDescFatalErr = 0x008000,
+
+	/*
+	 * Error summary flag is logical or of 'CRC Error', 'Collision Seen',
+	 * 'Frame Too Long', 'Runt' and 'Descriptor Error' flags generated
+	 * within tulip chip.
+	 */
+	RxDescErrorSummary = 0x8000,
+	RxDescCRCError = 0x0002,
+	RxDescCollisionSeen = 0x0040,
+
+	/*
+	 * 'Frame Too Long' flag is set if packet length including CRC exceeds
+	 * 1518.  However, a full sized VLAN tagged frame is 1522 bytes
+	 * including CRC.
+	 *
+	 * The tulip chip does not block oversized frames, and if this flag is
+	 * set on a receive descriptor it does not indicate the frame has been
+	 * truncated.  The receive descriptor also includes the actual length.
+	 * Therefore we can safety ignore this flag and check the length
+	 * ourselves.
+	 */
+	RxDescFrameTooLong = 0x0080,
+	RxDescRunt = 0x0800,
+	RxDescDescErr = 0x4000,
 	RxWholePkt   = 0x00000300,
+	/*
+	 * Top three bits of 14 bit frame length (status bits 27-29) should
+	 * never be set as that would make frame over 2047 bytes. The Receive
+	 * Watchdog flag (bit 4) may indicate the length is over 2048 and the
+	 * length field is invalid.
+	 */
+	RxLengthOver2047 = 0x38000010
 };
 
 
Signature · 1 line
1.6.0.4
maintainer Applied
#3 lore raw

From: Grant Grundler <[email protected]>
Date: Fri, 6 Mar 2009 11:13:22 -0700

Quoted 14 lines · Ivan Vecera
Quoted 13 lines

The original patch was submitted last year but wasn't discussed or applied because of missing maintainer's CCs. I only fixed some formatting errors, but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We should allow receiving frames of up to 1518 bytes in length, instead of 1514.

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Quoted 6 lines
Quoted 4 lines

Tested on D-Link DFE-570TX quad-fastethernet card.

Applied to net-next-2.6, thanks everyone.

#4 lore raw
In reply to Ivan Vecera
Quoted 9 lines · Ivan Vecera

The original patch was submitted last year but wasn't discussed or applied because of missing maintainer's CCs. I only fixed some formatting errors, but as I saw tulip is very badly formatted and needs further work.

Original description:
This patch fixes MTU problem, which occurs when using 802.1q VLANs. We should allow receiving frames of up to 1518 bytes in length, instead of 1514.

Quoted 9 lines

Based on patch written by Ben McKeegan for 2.4.x kernels. It is archived at http://www.candelatech.com/~greear/vlan/howto.html#tulip
I've adjusted a few things to make it apply on 2.6.x kernels.

Tested on D-Link DFE-570TX quad-fastethernet card.

Feel free to add Acked-by or Tested-by: Kyle McMartin <[email protected]>, it doesn't cause any regressions on any of my tulip cards.

regards, Kyle