Skip to contentSkip to conversation

ASIC3 support for tmio_mmc

PATCH Applied Philipp Zabel 5 participants 17 messages Jun 4, 2009 – Jun 13, 2009

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover ASIC3 support for tmio_mmc

I've broken the long lines in patches 1-3 and merged the fix into patch 2:
[PATCH 1/7] MFD,mmc: tmio_mmc: make HCLK configurable (v2)
[PATCH 2/7] mmc: tmio_mmc: add bus_shift support (v2)
[PATCH 3/7] mmc: tmio_mmc: don't use set_irq_type (v2)
[PATCH 4/7] mmc: tmio_mmc: correct probe return value for num_resources != 3
Also I've added three new patches for your consideration. Patch 5 delays mapping of the SD control registers because mfd_cell->enable has to enable the RAM first. Patch 6 fixes a bug in the SDCLK divider calculation and patch 7 finally enables compilation of tmio_mmc for ASIC3:
[PATCH 5/7] mmc: tmio_mmc: map SD control registers after enabling the MFD cell [PATCH 6/7] mmc: tmio_mmc: fix SDCLK divider setting
[PATCH 7/7] mmc: tmio_mmc: allow compilation for ASIC3

regards
Philipp

#1 lore raw

PATCH 1/7 MFD,mmc: tmio_mmc: make HCLK configurable

The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.

---
 drivers/mfd/t7l66xb.c       |    5 +++++
 drivers/mfd/tc6387xb.c      |    5 +++++
 drivers/mfd/tc6393xb.c      |    5 +++++
 drivers/mmc/host/tmio_mmc.c |   24 +++++++++++-------------
 include/linux/mfd/tmio.h    |    7 +++++++
 5 files changed, 33 insertions(+), 13 deletions(-)
drivers/mfd/t7l66xb.c +5 -0
index e9f4323..875f7a8 100644
@@ -108,6 +108,10 @@ static int t7l66xb_mmc_disable(struct platform_device *mmc)
 
 /*--------------------------------------------------------------------------*/
 
+static const struct tmio_mmc_data t7166xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static const struct resource t7l66xb_mmc_resources[] = {
 	{
 		.start = 0x800,
@@ -149,6 +153,7 @@ static struct mfd_cell t7l66xb_cells[] = {
 		.name = "tmio-mmc",
 		.enable = t7l66xb_mmc_enable,
 		.disable = t7l66xb_mmc_disable,
+		.driver_data = &t7166xb_mmc_data,
 		.num_resources = ARRAY_SIZE(t7l66xb_mmc_resources),
 		.resources = t7l66xb_mmc_resources,
 	},
drivers/mfd/tc6387xb.c +5 -0
index 43222c1..c3993ac 100644
@@ -75,6 +75,10 @@ static int tc6387xb_mmc_disable(struct platform_device *mmc)
 
 /*--------------------------------------------------------------------------*/
 
+const static struct tmio_mmc_data tc6387xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static struct resource tc6387xb_mmc_resources[] = {
 	{
 		.start = 0x800,
@@ -98,6 +102,7 @@ static struct mfd_cell tc6387xb_cells[] = {
 		.name = "tmio-mmc",
 		.enable = tc6387xb_mmc_enable,
 		.disable = tc6387xb_mmc_disable,
+		.driver_data = &tc6387xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6387xb_mmc_resources),
 		.resources = tc6387xb_mmc_resources,
 	},
drivers/mfd/tc6393xb.c +5 -0
index 77a12fc..9d2abb5 100644
@@ -136,6 +136,10 @@ static int tc6393xb_nand_enable(struct platform_device *nand)
 	return 0;
 }
 
+const static struct tmio_mmc_data tc6393xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static struct resource __devinitdata tc6393xb_nand_resources[] = {
 	{
 		.start	= 0x1000,
@@ -351,6 +355,7 @@ static struct mfd_cell __devinitdata tc6393xb_cells[] = {
 	},
 	[TC6393XB_CELL_MMC] = {
 		.name = "tmio-mmc",
+		.driver_data = &tc6393xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6393xb_mmc_resources),
 		.resources = tc6393xb_mmc_resources,
 	},
drivers/mmc/host/tmio_mmc.c +11 -13
index 63fbd5b..49df71e 100644
@@ -35,23 +35,14 @@
 
 #include "tmio_mmc.h"
 
-/*
- * Fixme - documentation conflicts on what the clock values are for the
- * various dividers.
- * One document I have says that its a divisor of a 24MHz clock, another 33.
- * This probably depends on HCLK for a given platform, so we may need to
- * require HCLK be passed to us from the MFD core.
- *
- */
-
 static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
 {
 	void __iomem *cnf = host->cnf;
 	void __iomem *ctl = host->ctl;
-	u32 clk = 0, clock;
+	u32 clk = 0, clock, f_min = host->mmc->f_min;
 
 	if (new_clock) {
-		for (clock = 46875, clk = 0x100; new_clock >= (clock<<1); ) {
+		for (clock = f_min, clk = 0x100; new_clock >= (clock<<1); ) {
 			clock <<= 1;
 			clk >>= 1;
 		}
@@ -545,6 +536,7 @@ out:
 static int __devinit tmio_mmc_probe(struct platform_device *dev)
 {
 	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
+	struct tmio_mmc_data *pdata;
 	struct resource *res_ctl, *res_cnf;
 	struct tmio_mmc_host *host;
 	struct mmc_host *mmc;
@@ -560,6 +552,12 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 		goto out;
 	}
 
+	pdata = cell->driver_data;
+	if (!pdata || !pdata->hclk) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	mmc = mmc_alloc_host(sizeof(struct tmio_mmc_host), &dev->dev);
 	if (!mmc)
 		goto out;
@@ -578,8 +576,8 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 
 	mmc->ops = &tmio_mmc_ops;
 	mmc->caps = MMC_CAP_4_BIT_DATA;
-	mmc->f_min = 46875; /* 24000000 / 512 */
-	mmc->f_max = 24000000;
+	mmc->f_max = pdata->hclk;
+	mmc->f_min = mmc->f_max / 512;
 	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	/* Enable the MMC/SD Control registers */
include/linux/mfd/tmio.h +7 -0
index 516d955..c377118 100644
@@ -19,6 +19,13 @@
 	} while (0)
 
 /*
+ * data for the MMC controller
+ */
+struct tmio_mmc_data {
+	unsigned int		hclk;
+};
+
+/*
  * data for the NAND controller
  */
 struct tmio_nand_data {
Signature · 1 line
1.6.3.1
Applied
#2 lore raw

Re: [PATCH 1/7] MFD,mmc: tmio_mmc: make HCLK configurable

Hi Philip,

Quoted 3 lines · Philipp Zabel

The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.

Applied to my for-next branch, many thanks.

Quoted 164 lines
---
 drivers/mfd/t7l66xb.c       |    5 +++++
 drivers/mfd/tc6387xb.c      |    5 +++++
 drivers/mfd/tc6393xb.c      |    5 +++++
 drivers/mmc/host/tmio_mmc.c |   24 +++++++++++-------------
 include/linux/mfd/tmio.h    |    7 +++++++
 5 files changed, 33 insertions(+), 13 deletions(-)
drivers/mfd/t7l66xb.c +5 -0
index e9f4323..875f7a8 100644
@@ -108,6 +108,10 @@ static int t7l66xb_mmc_disable(struct platform_device *mmc)
 
 /*--------------------------------------------------------------------------*/
 
+static const struct tmio_mmc_data t7166xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static const struct resource t7l66xb_mmc_resources[] = {
 	{
 		.start = 0x800,
@@ -149,6 +153,7 @@ static struct mfd_cell t7l66xb_cells[] = {
 		.name = "tmio-mmc",
 		.enable = t7l66xb_mmc_enable,
 		.disable = t7l66xb_mmc_disable,
+		.driver_data = &t7166xb_mmc_data,
 		.num_resources = ARRAY_SIZE(t7l66xb_mmc_resources),
 		.resources = t7l66xb_mmc_resources,
 	},
drivers/mfd/tc6387xb.c +5 -0
index 43222c1..c3993ac 100644
@@ -75,6 +75,10 @@ static int tc6387xb_mmc_disable(struct platform_device *mmc)
 
 /*--------------------------------------------------------------------------*/
 
+const static struct tmio_mmc_data tc6387xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static struct resource tc6387xb_mmc_resources[] = {
 	{
 		.start = 0x800,
@@ -98,6 +102,7 @@ static struct mfd_cell tc6387xb_cells[] = {
 		.name = "tmio-mmc",
 		.enable = tc6387xb_mmc_enable,
 		.disable = tc6387xb_mmc_disable,
+		.driver_data = &tc6387xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6387xb_mmc_resources),
 		.resources = tc6387xb_mmc_resources,
 	},
drivers/mfd/tc6393xb.c +5 -0
index 77a12fc..9d2abb5 100644
@@ -136,6 +136,10 @@ static int tc6393xb_nand_enable(struct platform_device *nand)
 	return 0;
 }
 
+const static struct tmio_mmc_data tc6393xb_mmc_data = {
+	.hclk = 24000000,
+};
+
 static struct resource __devinitdata tc6393xb_nand_resources[] = {
 	{
 		.start	= 0x1000,
@@ -351,6 +355,7 @@ static struct mfd_cell __devinitdata tc6393xb_cells[] = {
 	},
 	[TC6393XB_CELL_MMC] = {
 		.name = "tmio-mmc",
+		.driver_data = &tc6393xb_mmc_data,
 		.num_resources = ARRAY_SIZE(tc6393xb_mmc_resources),
 		.resources = tc6393xb_mmc_resources,
 	},
drivers/mmc/host/tmio_mmc.c +11 -13
index 63fbd5b..49df71e 100644
@@ -35,23 +35,14 @@
 
 #include "tmio_mmc.h"
 
-/*
- * Fixme - documentation conflicts on what the clock values are for the
- * various dividers.
- * One document I have says that its a divisor of a 24MHz clock, another 33.
- * This probably depends on HCLK for a given platform, so we may need to
- * require HCLK be passed to us from the MFD core.
- *
- */
-
 static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
 {
 	void __iomem *cnf = host->cnf;
 	void __iomem *ctl = host->ctl;
-	u32 clk = 0, clock;
+	u32 clk = 0, clock, f_min = host->mmc->f_min;
 
 	if (new_clock) {
-		for (clock = 46875, clk = 0x100; new_clock >= (clock<<1); ) {
+		for (clock = f_min, clk = 0x100; new_clock >= (clock<<1); ) {
 			clock <<= 1;
 			clk >>= 1;
 		}
@@ -545,6 +536,7 @@ out:
 static int __devinit tmio_mmc_probe(struct platform_device *dev)
 {
 	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
+	struct tmio_mmc_data *pdata;
 	struct resource *res_ctl, *res_cnf;
 	struct tmio_mmc_host *host;
 	struct mmc_host *mmc;
@@ -560,6 +552,12 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 		goto out;
 	}
 
+	pdata = cell->driver_data;
+	if (!pdata || !pdata->hclk) {
+		ret = -EINVAL;
+		goto out;
+	}
+
 	mmc = mmc_alloc_host(sizeof(struct tmio_mmc_host), &dev->dev);
 	if (!mmc)
 		goto out;
@@ -578,8 +576,8 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 
 	mmc->ops = &tmio_mmc_ops;
 	mmc->caps = MMC_CAP_4_BIT_DATA;
-	mmc->f_min = 46875; /* 24000000 / 512 */
-	mmc->f_max = 24000000;
+	mmc->f_max = pdata->hclk;
+	mmc->f_min = mmc->f_max / 512;
 	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	/* Enable the MMC/SD Control registers */
include/linux/mfd/tmio.h +7 -0
index 516d955..c377118 100644
@@ -19,6 +19,13 @@
 	} while (0)
 
 /*
+ * data for the MMC controller
+ */
+struct tmio_mmc_data {
+	unsigned int		hclk;
+};
+
+/*
  * data for the NAND controller
  */
 struct tmio_nand_data {
Signature · 1 line
1.6.3.1
Signature · 2 lines
Intel Open Source Technology Centre
http://oss.intel.com/
#3 lore raw

PATCH 2/7 mmc: tmio_mmc: add bus_shift support

In reply to Philipp Zabel

Some ASIC3 devices in the wild are connected with the address bus shifted by one line, so that its 16-bit registers appear 32-bit aligned in host memory space.

---
 drivers/mmc/host/tmio_mmc.c |  129 +++++++++++++++++++------------------------
 drivers/mmc/host/tmio_mmc.h |   77 ++++++++++++++++++++++---
 2 files changed, 125 insertions(+), 81 deletions(-)
drivers/mmc/host/tmio_mmc.c +57 -72
index 49df71e..01add9b 100644
@@ -37,8 +37,6 @@
 
 static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
 {
-	void __iomem *cnf = host->cnf;
-	void __iomem *ctl = host->ctl;
 	u32 clk = 0, clock, f_min = host->mmc->f_min;
 
 	if (new_clock) {
@@ -50,45 +48,39 @@ static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
 			clk = 0x20000;
 
 		clk >>= 2;
-		tmio_iowrite8((clk & 0x8000) ? 0 : 1, cnf + CNF_SD_CLK_MODE);
+		sd_config_write8(host, CNF_SD_CLK_MODE, (clk & 0x8000) ? 0 : 1);
 		clk |= 0x100;
 	}
 
-	tmio_iowrite16(clk, ctl + CTL_SD_CARD_CLK_CTL);
+	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk);
 }
 
 static void tmio_mmc_clk_stop(struct tmio_mmc_host *host)
 {
-	void __iomem *ctl = host->ctl;
-
-	tmio_iowrite16(0x0000, ctl + CTL_CLK_AND_WAIT_CTL);
+	sd_ctrl_write16(host, CTL_CLK_AND_WAIT_CTL, 0x0000);
 	msleep(10);
-	tmio_iowrite16(tmio_ioread16(ctl + CTL_SD_CARD_CLK_CTL) & ~0x0100,
-	       ctl + CTL_SD_CARD_CLK_CTL);
+	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, ~0x0100 &
+		sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL));
 	msleep(10);
 }
 
 static void tmio_mmc_clk_start(struct tmio_mmc_host *host)
 {
-	void __iomem *ctl = host->ctl;
-
-	tmio_iowrite16(tmio_ioread16(ctl + CTL_SD_CARD_CLK_CTL) | 0x0100,
-	       ctl + CTL_SD_CARD_CLK_CTL);
+	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, 0x0100 |
+		sd_ctrl_read16(host, CTL_SD_CARD_CLK_CTL));
 	msleep(10);
-	tmio_iowrite16(0x0100, ctl + CTL_CLK_AND_WAIT_CTL);
+	sd_ctrl_write16(host, CTL_CLK_AND_WAIT_CTL, 0x0100);
 	msleep(10);
 }
 
 static void reset(struct tmio_mmc_host *host)
 {
-	void __iomem *ctl = host->ctl;
-
 	/* FIXME - should we set stop clock reg here */
-	tmio_iowrite16(0x0000, ctl + CTL_RESET_SD);
-	tmio_iowrite16(0x0000, ctl + CTL_RESET_SDIO);
+	sd_ctrl_write16(host, CTL_RESET_SD, 0x0000);
+	sd_ctrl_write16(host, CTL_RESET_SDIO, 0x0000);
 	msleep(10);
-	tmio_iowrite16(0x0001, ctl + CTL_RESET_SD);
-	tmio_iowrite16(0x0001, ctl + CTL_RESET_SDIO);
+	sd_ctrl_write16(host, CTL_RESET_SD, 0x0001);
+	sd_ctrl_write16(host, CTL_RESET_SDIO, 0x0001);
 	msleep(10);
 }
 
@@ -120,13 +112,12 @@ tmio_mmc_finish_request(struct tmio_mmc_host *host)
 static int
 tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
 {
-	void __iomem *ctl = host->ctl;
 	struct mmc_data *data = host->data;
 	int c = cmd->opcode;
 
 	/* Command 12 is handled by hardware */
 	if (cmd->opcode == 12 && !cmd->arg) {
-		tmio_iowrite16(0x001, ctl + CTL_STOP_INTERNAL_ACTION);
+		sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0x001);
 		return 0;
 	}
 
@@ -151,18 +142,18 @@ tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
 	if (data) {
 		c |= DATA_PRESENT;
 		if (data->blocks > 1) {
-			tmio_iowrite16(0x100, ctl + CTL_STOP_INTERNAL_ACTION);
+			sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0x100);
 			c |= TRANSFER_MULTI;
 		}
 		if (data->flags & MMC_DATA_READ)
 			c |= TRANSFER_READ;
 	}
 
-	enable_mmc_irqs(ctl, TMIO_MASK_CMD);
+	enable_mmc_irqs(host, TMIO_MASK_CMD);
 
 	/* Fire off the command */
-	tmio_iowrite32(cmd->arg, ctl + CTL_ARG_REG);
-	tmio_iowrite16(c, ctl + CTL_SD_CMD);
+	sd_ctrl_write32(host, CTL_ARG_REG, cmd->arg);
+	sd_ctrl_write16(host, CTL_SD_CMD, c);
 
 	return 0;
 }
@@ -174,7 +165,6 @@ tmio_mmc_start_command(struct tmio_mmc_host *host, struct mmc_command *cmd)
  */
 static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
 {
-	void __iomem *ctl = host->ctl;
 	struct mmc_data *data = host->data;
 	unsigned short *buf;
 	unsigned int count;
@@ -197,9 +187,9 @@ static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
 
 	/* Transfer the data */
 	if (data->flags & MMC_DATA_READ)
-		tmio_ioread16_rep(ctl + CTL_SD_DATA_PORT, buf, count >> 1);
+		sd_ctrl_read16_rep(host, CTL_SD_DATA_PORT, buf, count >> 1);
 	else
-		tmio_iowrite16_rep(ctl + CTL_SD_DATA_PORT, buf, count >> 1);
+		sd_ctrl_write16_rep(host, CTL_SD_DATA_PORT, buf, count >> 1);
 
 	host->sg_off += count;
 
@@ -213,7 +203,6 @@ static inline void tmio_mmc_pio_irq(struct tmio_mmc_host *host)
 
 static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 {
-	void __iomem *ctl = host->ctl;
 	struct mmc_data *data = host->data;
 	struct mmc_command *stop;
 
@@ -242,13 +231,13 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 	 */
 
 	if (data->flags & MMC_DATA_READ)
-		disable_mmc_irqs(ctl, TMIO_MASK_READOP);
+		disable_mmc_irqs(host, TMIO_MASK_READOP);
 	else
-		disable_mmc_irqs(ctl, TMIO_MASK_WRITEOP);
+		disable_mmc_irqs(host, TMIO_MASK_WRITEOP);
 
 	if (stop) {
 		if (stop->opcode == 12 && !stop->arg)
-			tmio_iowrite16(0x000, ctl + CTL_STOP_INTERNAL_ACTION);
+			sd_ctrl_write16(host, CTL_STOP_INTERNAL_ACTION, 0x000);
 		else
 			BUG();
 	}
@@ -259,9 +248,8 @@ static inline void tmio_mmc_data_irq(struct tmio_mmc_host *host)
 static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 	unsigned int stat)
 {
-	void __iomem *ctl = host->ctl, *addr;
 	struct mmc_command *cmd = host->cmd;
-	int i;
+	int i, addr;
 
 	if (!host->cmd) {
 		pr_debug("Spurious CMD irq\n");
@@ -275,8 +263,8 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 	 * modify the order of the response for short response command types.
 	 */
 
-	for (i = 3, addr = ctl + CTL_RESPONSE ; i >= 0 ; i--, addr += 4)
-		cmd->resp[i] = tmio_ioread32(addr);
+	for (i = 3, addr = CTL_RESPONSE ; i >= 0 ; i--, addr += 4)
+		cmd->resp[i] = sd_ctrl_read32(host, addr);
 
 	if (cmd->flags &  MMC_RSP_136) {
 		cmd->resp[0] = (cmd->resp[0] << 8) | (cmd->resp[1] >> 24);
@@ -298,9 +286,9 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 	 */
 	if (host->data && !cmd->error) {
 		if (host->data->flags & MMC_DATA_READ)
-			enable_mmc_irqs(ctl, TMIO_MASK_READOP);
+			enable_mmc_irqs(host, TMIO_MASK_READOP);
 		else
-			enable_mmc_irqs(ctl, TMIO_MASK_WRITEOP);
+			enable_mmc_irqs(host, TMIO_MASK_WRITEOP);
 	} else {
 		tmio_mmc_finish_request(host);
 	}
@@ -312,20 +300,19 @@ static inline void tmio_mmc_cmd_irq(struct tmio_mmc_host *host,
 static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 {
 	struct tmio_mmc_host *host = devid;
-	void __iomem *ctl = host->ctl;
 	unsigned int ireg, irq_mask, status;
 
 	pr_debug("MMC IRQ begin\n");
 
-	status = tmio_ioread32(ctl + CTL_STATUS);
-	irq_mask = tmio_ioread32(ctl + CTL_IRQ_MASK);
+	status = sd_ctrl_read32(host, CTL_STATUS);
+	irq_mask = sd_ctrl_read32(host, CTL_IRQ_MASK);
 	ireg = status & TMIO_MASK_IRQ & ~irq_mask;
 
 	pr_debug_status(status);
 	pr_debug_status(ireg);
 
 	if (!ireg) {
-		disable_mmc_irqs(ctl, status & ~irq_mask);
+		disable_mmc_irqs(host, status & ~irq_mask);
 
 		pr_debug("tmio_mmc: Spurious irq, disabling! "
 			"0x%08x 0x%08x 0x%08x\n", status, irq_mask, ireg);
@@ -337,7 +324,7 @@ static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 	while (ireg) {
 		/* Card insert / remove attempts */
 		if (ireg & (TMIO_STAT_CARD_INSERT | TMIO_STAT_CARD_REMOVE)) {
-			ack_mmc_irqs(ctl, TMIO_STAT_CARD_INSERT |
+			ack_mmc_irqs(host, TMIO_STAT_CARD_INSERT |
 				TMIO_STAT_CARD_REMOVE);
 			mmc_detect_change(host->mmc, 0);
 		}
@@ -349,25 +336,25 @@ static irqreturn_t tmio_mmc_irq(int irq, void *devid)
 
 		/* Command completion */
 		if (ireg & TMIO_MASK_CMD) {
-			ack_mmc_irqs(ctl, TMIO_MASK_CMD);
+			ack_mmc_irqs(host, TMIO_MASK_CMD);
 			tmio_mmc_cmd_irq(host, status);
 		}
 
 		/* Data transfer */
 		if (ireg & (TMIO_STAT_RXRDY | TMIO_STAT_TXRQ)) {
-			ack_mmc_irqs(ctl, TMIO_STAT_RXRDY | TMIO_STAT_TXRQ);
+			ack_mmc_irqs(host, TMIO_STAT_RXRDY | TMIO_STAT_TXRQ);
 			tmio_mmc_pio_irq(host);
 		}
 
 		/* Data transfer completion */
 		if (ireg & TMIO_STAT_DATAEND) {
-			ack_mmc_irqs(ctl, TMIO_STAT_DATAEND);
+			ack_mmc_irqs(host, TMIO_STAT_DATAEND);
 			tmio_mmc_data_irq(host);
 		}
 
 		/* Check status - keep going until we've handled it all */
-		status = tmio_ioread32(ctl + CTL_STATUS);
-		irq_mask = tmio_ioread32(ctl + CTL_IRQ_MASK);
+		status = sd_ctrl_read32(host, CTL_STATUS);
+		irq_mask = sd_ctrl_read32(host, CTL_IRQ_MASK);
 		ireg = status & TMIO_MASK_IRQ & ~irq_mask;
 
 		pr_debug("Status at end of loop: %08x\n", status);
@@ -382,8 +369,6 @@ out:
 static int tmio_mmc_start_data(struct tmio_mmc_host *host,
 	struct mmc_data *data)
 {
-	void __iomem *ctl = host->ctl;
-
 	pr_debug("setup data transfer: blocksize %08x  nr_blocks %d\n",
 	    data->blksz, data->blocks);
 
@@ -398,8 +383,8 @@ static int tmio_mmc_start_data(struct tmio_mmc_host *host,
 	host->data = data;
 
 	/* Set transfer length / blocksize */
-	tmio_iowrite16(data->blksz,  ctl + CTL_SD_XFER_LEN);
-	tmio_iowrite16(data->blocks, ctl + CTL_XFER_BLK_COUNT);
+	sd_ctrl_write16(host, CTL_SD_XFER_LEN, data->blksz);
+	sd_ctrl_write16(host, CTL_XFER_BLK_COUNT, data->blocks);
 
 	return 0;
 }
@@ -440,8 +425,6 @@ fail:
 static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 {
 	struct tmio_mmc_host *host = mmc_priv(mmc);
-	void __iomem *cnf = host->cnf;
-	void __iomem *ctl = host->ctl;
 
 	if (ios->clock)
 		tmio_mmc_set_clock(host, ios->clock);
@@ -449,12 +432,12 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 	/* Power sequence - OFF -> ON -> UP */
 	switch (ios->power_mode) {
 	case MMC_POWER_OFF: /* power down SD bus */
-		tmio_iowrite8(0x00, cnf + CNF_PWR_CTL_2);
+		sd_config_write8(host, CNF_PWR_CTL_2, 0x00);
 		tmio_mmc_clk_stop(host);
 		break;
 	case MMC_POWER_ON: /* power up SD bus */
 
-		tmio_iowrite8(0x02, cnf + CNF_PWR_CTL_2);
+		sd_config_write8(host, CNF_PWR_CTL_2, 0x02);
 		break;
 	case MMC_POWER_UP: /* start bus clock */
 		tmio_mmc_clk_start(host);
@@ -463,10 +446,10 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 
 	switch (ios->bus_width) {
 	case MMC_BUS_WIDTH_1:
-		tmio_iowrite16(0x80e0, ctl + CTL_SD_MEM_CARD_OPT);
+		sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, 0x80e0);
 	break;
 	case MMC_BUS_WIDTH_4:
-		tmio_iowrite16(0x00e0, ctl + CTL_SD_MEM_CARD_OPT);
+		sd_ctrl_write16(host, CTL_SD_MEM_CARD_OPT, 0x00e0);
 	break;
 	}
 
@@ -477,9 +460,8 @@ static void tmio_mmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
 static int tmio_mmc_get_ro(struct mmc_host *mmc)
 {
 	struct tmio_mmc_host *host = mmc_priv(mmc);
-	void __iomem *ctl = host->ctl;
 
-	return (tmio_ioread16(ctl + CTL_STATUS) & TMIO_STAT_WRPROTECT) ? 0 : 1;
+	return (sd_ctrl_read16(host, CTL_STATUS) & TMIO_STAT_WRPROTECT) ? 0 : 1;
 }
 
 static struct mmc_host_ops tmio_mmc_ops = {
@@ -509,12 +491,12 @@ static int tmio_mmc_resume(struct platform_device *dev)
 	struct mfd_cell	*cell = (struct mfd_cell *)dev->dev.platform_data;
 	struct mmc_host *mmc = platform_get_drvdata(dev);
 	struct tmio_mmc_host *host = mmc_priv(mmc);
-	void __iomem *cnf = host->cnf;
 	int ret = 0;
 
 	/* Enable the MMC/SD Control registers */
-	tmio_iowrite16(SDCREN, cnf + CNF_CMD);
-	tmio_iowrite32(dev->resource[0].start & 0xfffe, cnf + CNF_CTL_BASE);
+	sd_config_write16(host, CNF_CMD, SDCREN);
+	sd_config_write32(host, CNF_CTL_BASE,
+		(dev->resource[0].start >> host->bus_shift) & 0xfffe);
 
 	/* Tell the MFD core we are ready to be enabled */
 	if (cell->enable) {
@@ -566,6 +548,9 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	host->mmc = mmc;
 	platform_set_drvdata(dev, mmc);
 
+	/* SD control register space size is 0x200, 0x400 for bus_shift=1 */
+	host->bus_shift = resource_size(res_ctl) >> 10;
+
 	host->ctl = ioremap(res_ctl->start, resource_size(res_ctl));
 	if (!host->ctl)
 		goto host_free;
@@ -581,9 +566,9 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
 	/* Enable the MMC/SD Control registers */
-	tmio_iowrite16(SDCREN, host->cnf + CNF_CMD);
-	tmio_iowrite32(dev->resource[0].start & 0xfffe,
-		host->cnf + CNF_CTL_BASE);
+	sd_config_write16(host, CNF_CMD, SDCREN);
+	sd_config_write32(host, CNF_CTL_BASE,
+		(dev->resource[0].start >> host->bus_shift) & 0xfffe);
 
 	/* Tell the MFD core we are ready to be enabled */
 	if (cell->enable) {
@@ -593,13 +578,13 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	}
 
 	/* Disable SD power during suspend */
-	tmio_iowrite8(0x01, host->cnf + CNF_PWR_CTL_3);
+	sd_config_write8(host, CNF_PWR_CTL_3, 0x01);
 
 	/* The below is required but why? FIXME */
-	tmio_iowrite8(0x1f, host->cnf + CNF_STOP_CLK_CTL);
+	sd_config_write8(host, CNF_STOP_CLK_CTL, 0x1f);
 
 	/* Power down SD bus*/
-	tmio_iowrite8(0x0,  host->cnf + CNF_PWR_CTL_2);
+	sd_config_write8(host, CNF_PWR_CTL_2, 0x00);
 
 	tmio_mmc_clk_stop(host);
 	reset(host);
@@ -610,7 +595,7 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	else
 		goto unmap_cnf;
 
-	disable_mmc_irqs(host->ctl, TMIO_MASK_ALL);
+	disable_mmc_irqs(host, TMIO_MASK_ALL);
 
 	ret = request_irq(host->irq, tmio_mmc_irq, IRQF_DISABLED, "tmio-mmc",
 		host);
@@ -625,7 +610,7 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	       (unsigned long)host->ctl, host->irq);
 
 	/* Unmask the IRQs we want to know about */
-	enable_mmc_irqs(host->ctl,  TMIO_MASK_IRQ);
+	enable_mmc_irqs(host, TMIO_MASK_IRQ);
 
 	return 0;
 
drivers/mmc/host/tmio_mmc.h +68 -9

108 lines not on this page · raw message

Signature · 1 line
1.6.3.1
#4 lore raw

PATCH 3/7 mmc: tmio_mmc: don't use set_irq_type (v2)

In reply to Philipp Zabel

Use an IRQF_TRIGGER_ flag in request_irq instead.

---
 drivers/mmc/host/tmio_mmc.c |    6 ++----
 1 files changed, 2 insertions(+), 4 deletions(-)
drivers/mmc/host/tmio_mmc.c +2 -4
index 01add9b..bbcbd72 100644
@@ -597,13 +597,11 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 
 	disable_mmc_irqs(host, TMIO_MASK_ALL);
 
-	ret = request_irq(host->irq, tmio_mmc_irq, IRQF_DISABLED, "tmio-mmc",
-		host);
+	ret = request_irq(host->irq, tmio_mmc_irq, IRQF_DISABLED |
+		IRQF_TRIGGER_FALLING, "tmio-mmc", host);
 	if (ret)
 		goto unmap_cnf;
 
-	set_irq_type(host->irq, IRQ_TYPE_EDGE_FALLING);
-
 	mmc_add_host(mmc);
 
 	printk(KERN_INFO "%s at 0x%08lx irq %d\n", mmc_hostname(host->mmc),
Signature · 1 line
1.6.3.1
#5 lore raw

PATCH 4/7 mmc: tmio_mmc: correct probe return value for num_resources != 3

In reply to Philipp Zabel
---
 drivers/mmc/host/tmio_mmc.c |   12 +++++-------
 1 files changed, 5 insertions(+), 7 deletions(-)
drivers/mmc/host/tmio_mmc.c +5 -7
index bbcbd72..b576640 100644
@@ -522,23 +522,21 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	struct resource *res_ctl, *res_cnf;
 	struct tmio_mmc_host *host;
 	struct mmc_host *mmc;
-	int ret = -ENOMEM;
+	int ret = -EINVAL;
 
 	if (dev->num_resources != 3)
 		goto out;
 
 	res_ctl = platform_get_resource(dev, IORESOURCE_MEM, 0);
 	res_cnf = platform_get_resource(dev, IORESOURCE_MEM, 1);
-	if (!res_ctl || !res_cnf) {
-		ret = -EINVAL;
+	if (!res_ctl || !res_cnf)
 		goto out;
-	}
 
 	pdata = cell->driver_data;
-	if (!pdata || !pdata->hclk) {
-		ret = -EINVAL;
+	if (!pdata || !pdata->hclk)
 		goto out;
-	}
+
+	ret = -ENOMEM;
 
 	mmc = mmc_alloc_host(sizeof(struct tmio_mmc_host), &dev->dev);
 	if (!mmc)
Signature · 1 line
1.6.3.1
#6 lore raw

PATCH 5/7 mmc: tmio_mmc: map SD control registers after enabling the MFD cell

In reply to Philipp Zabel

ASIC3 can disable the memory, so we need to wait for mfd_cell->enable to enable the memory before we can map the SD control registers.

Cc Pierre Ossman <[email protected]>
Cc Ian Molton <[email protected]>
---
 drivers/mmc/host/tmio_mmc.c |   20 ++++++++++----------
 1 files changed, 10 insertions(+), 10 deletions(-)
drivers/mmc/host/tmio_mmc.c +10 -10
index b576640..fe6d2b6 100644
@@ -493,11 +493,6 @@ static int tmio_mmc_resume(struct platform_device *dev)
 	struct tmio_mmc_host *host = mmc_priv(mmc);
 	int ret = 0;
 
-	/* Enable the MMC/SD Control registers */
-	sd_config_write16(host, CNF_CMD, SDCREN);
-	sd_config_write32(host, CNF_CTL_BASE,
-		(dev->resource[0].start >> host->bus_shift) & 0xfffe);
-
 	/* Tell the MFD core we are ready to be enabled */
 	if (cell->enable) {
 		ret = cell->enable(dev);
@@ -505,6 +500,11 @@ static int tmio_mmc_resume(struct platform_device *dev)
 			goto out;
 	}
 
+	/* Enable the MMC/SD Control registers */
+	sd_config_write16(host, CNF_CMD, SDCREN);
+	sd_config_write32(host, CNF_CTL_BASE,
+		(dev->resource[0].start >> host->bus_shift) & 0xfffe);
+
 	mmc_resume_host(mmc);
 
 out:
@@ -563,11 +563,6 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 	mmc->f_min = mmc->f_max / 512;
 	mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
 
-	/* Enable the MMC/SD Control registers */
-	sd_config_write16(host, CNF_CMD, SDCREN);
-	sd_config_write32(host, CNF_CTL_BASE,
-		(dev->resource[0].start >> host->bus_shift) & 0xfffe);
-
 	/* Tell the MFD core we are ready to be enabled */
 	if (cell->enable) {
 		ret = cell->enable(dev);
@@ -575,6 +570,11 @@ static int __devinit tmio_mmc_probe(struct platform_device *dev)
 			goto unmap_cnf;
 	}
 
+	/* Enable the MMC/SD Control registers */
+	sd_config_write16(host, CNF_CMD, SDCREN);
+	sd_config_write32(host, CNF_CTL_BASE,
+		(dev->resource[0].start >> host->bus_shift) & 0xfffe);
+
 	/* Disable SD power during suspend */
 	sd_config_write8(host, CNF_PWR_CTL_3, 0x01);
 
Signature · 1 line
1.6.3.1
#8 lore raw

PATCH 6/7 mmc: tmio_mmc: fix SDCLK divider setting

In reply to Philipp Zabel

Except for the SDCLK = HCLK (divider bypassed) case, the clock setting resulted in double the requested frequency. The smallest possible frequency (f_max/512) is configured with a divider setting 0x80, not 0x40.

---
 drivers/mmc/host/tmio_mmc.c |    6 +++---
 1 files changed, 3 insertions(+), 3 deletions(-)
drivers/mmc/host/tmio_mmc.c +3 -3
index fe6d2b6..9f6e180 100644
@@ -44,10 +44,10 @@ static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
 			clock <<= 1;
 			clk >>= 1;
 		}
-		if (clk & 0x1)
-			clk = 0x20000;
+		if (clk == 0)
+			clk = 0x8000 << 1;
 
-		clk >>= 2;
+		clk >>= 1;
 		sd_config_write8(host, CNF_SD_CLK_MODE, (clk & 0x8000) ? 0 : 1);
 		clk |= 0x100;
 	}
Signature · 1 line
1.6.3.1
#9 lore raw

Re: [PATCH 6/7] mmc: tmio_mmc: fix SDCLK divider setting

Quoted 4 lines · Philipp Zabel

Except for the SDCLK = HCLK (divider bypassed) case, the clock setting resulted in double the requested frequency. The smallest possible frequency (f_max/512) is configured with a divider setting 0x80, not 0x40.

I have (IMO) a better fix, which also removes some crap being written to CTL_SD_CARD_CLK_CTL.

Pierre, please replace patch 6/7 from Philips set with this one.

From e69efa520b07a688643ce5f8e8d41bef753ff1ed Mon Sep 17 00:00:00 2001
From: Ian Molton <[email protected]>
Date: Fri, 12 Jun 2009 21:53:05 +0100
Subject: [PATCH] MMC: fix clock setup in tmio_mmc

This patch fixes the clock setup in tmio_mmc.

* Incorrect divider setting
* Cruft written to the clock registers (seemingly harmless but Not
Good (tm))

It also eliminates some unnecessary ifs and tidies the loop syntax.

Thanks to Philipp Zabel who discovered the divider issue, commenting

"Except for the SDCLK = HCLK (divider bypassed) case, the clock
setting resulted in double the requested frequency. The smallest possible frequency (f_max/512) is configured with a divider setting 0x80, not 0x40."

---
 drivers/mmc/host/tmio_mmc.c |   15 +++++----------
 1 files changed, 5 insertions(+), 10 deletions(-)
drivers/mmc/host/tmio_mmc.c +5 -10
index fe6d2b6..10951b7 100644
@@ -37,22 +37,17 @@
 
 static void tmio_mmc_set_clock(struct tmio_mmc_host *host, int new_clock)
 {
-	u32 clk = 0, clock, f_min = host->mmc->f_min;
+	u32 clk = 0, clock;
 
 	if (new_clock) {
-		for (clock = f_min, clk = 0x100; new_clock >= (clock<<1); ) {
+		for (clock = host->mmc->f_min, clk = 0x80000080;
+			new_clock >= (clock<<1); clk >>= 1)
 			clock <<= 1;
-			clk >>= 1;
-		}
-		if (clk & 0x1)
-			clk = 0x20000;
-
-		clk >>= 2;
-		sd_config_write8(host, CNF_SD_CLK_MODE, (clk & 0x8000) ? 0 : 1);
 		clk |= 0x100;
 	}
 
-	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk);
+	sd_config_write8(host, CNF_SD_CLK_MODE, clk >> 22);
+	sd_ctrl_write16(host, CTL_SD_CARD_CLK_CTL, clk & 0x1ff);
 }
 
 static void tmio_mmc_clk_stop(struct tmio_mmc_host *host)
Signature · 1 line
1.6.3.1
#10 lore raw

PATCH 7/7 mmc: tmio_mmc: allow compilation for ASIC3

In reply to Philipp Zabel

Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.

Cc Pierre Ossman <[email protected]>
Cc Ian Molton <[email protected]>
---
 drivers/mmc/host/Kconfig    |    4 ++--
 drivers/mmc/host/tmio_mmc.c |    2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/mmc/host/Kconfig +2 -2
index b4cf691..9aae7f5 100644
@@ -237,7 +237,7 @@ config MMC_SDRICOH_CS
 
 config MMC_TMIO
 	tristate "Toshiba Mobile IO Controller (TMIO) MMC/SD function support"
-	depends on MFD_TMIO
+	depends on MFD_TMIO || MFD_ASIC3
 	help
 	  This provides support for the SD/MMC cell found in TC6393XB,
-	  T7L66XB and also ipaq ASIC3
+	  T7L66XB and also HTC ASIC3.
drivers/mmc/host/tmio_mmc.c +1 -1
index 9f6e180..9f68c2f 100644
@@ -10,7 +10,7 @@
  *
  * Driver for the MMC / SD / SDIO cell found in:
  *
- * TC6393XB TC6391XB TC6387XB T7L66XB
+ * TC6393XB TC6391XB TC6387XB T7L66XB ASIC3
  *
  * This driver draws mainly on scattered spec sheets, Reverse engineering
  * of the toshiba e800  SD driver and some parts of the 2.4 ASIC3 driver (4 bit
Signature · 1 line
1.6.3.1
#11 lore raw

Re: [PATCH 7/7] mmc: tmio_mmc: allow compilation for ASIC3

Does this patch actually _do_ anything? wont the asic3 driver need modifying to use tmio_mmc before this patch is useful?

Is the idea that this patch go in and asic3 MFDs migrate gradually?

If so then I'll ack it.

Quoted 37 lines · Philipp Zabel

Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.

Cc Pierre Ossman <[email protected]>
Cc Ian Molton <[email protected]>
---
 drivers/mmc/host/Kconfig    |    4 ++--
 drivers/mmc/host/tmio_mmc.c |    2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/mmc/host/Kconfig +2 -2
index b4cf691..9aae7f5 100644
@@ -237,7 +237,7 @@ config MMC_SDRICOH_CS
 
 config MMC_TMIO
 	tristate "Toshiba Mobile IO Controller (TMIO) MMC/SD function support"
-	depends on MFD_TMIO
+	depends on MFD_TMIO || MFD_ASIC3
 	help
 	  This provides support for the SD/MMC cell found in TC6393XB,
-	  T7L66XB and also ipaq ASIC3
+	  T7L66XB and also HTC ASIC3.
drivers/mmc/host/tmio_mmc.c +1 -1
index 9f6e180..9f68c2f 100644
@@ -10,7 +10,7 @@
  *
  * Driver for the MMC / SD / SDIO cell found in:
  *
- * TC6393XB TC6391XB TC6387XB T7L66XB
+ * TC6393XB TC6391XB TC6387XB T7L66XB ASIC3
  *
  * This driver draws mainly on scattered spec sheets, Reverse engineering
  * of the toshiba e800  SD driver and some parts of the 2.4 ASIC3 driver (4 bit
#12 lore raw

Re: [PATCH 7/7] mmc: tmio_mmc: allow compilation for ASIC3

Quoted 2 lines · Ian molton

Does this patch actually _do_ anything? wont the asic3 driver need modifying to use tmio_mmc before this patch is useful?

That's right, this patch only allows tmio-mmc to be compiled on ASIC3 based devices. The needed changes to ASIC3
(http://patchwork.kernel.org/patch/28000/ et al) are queued in the MFD tree.

Quoted 1 line

Is the idea that this patch go in and asic3 MFDs migrate gradually?

The idea was that this patch is applied after tmio-mmc is ASIC3-ready, so that it doesn't matter whether the MFD or MMC tree gets merged first. If the ASIC3 MFD changes come first, at least tmio-mmc won't be built (for CONFIG_MFD_ASIC3) until the tmio-mmc modifications are in.

Quoted 34 lines

If so then I'll ack it.

Quoted 31 lines · Philipp Zabel

Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.

Cc Pierre Ossman <[email protected]>
Cc Ian Molton <[email protected]>

---
 drivers/mmc/host/Kconfig    |    4 ++--
 drivers/mmc/host/tmio_mmc.c |    2 +-

 2 files changed, 3 insertions(+), 3 deletions(-)
drivers/mmc/host/Kconfig +0 -0
index b4cf691..9aae7f5 100644
@@ -237,7 +237,7 @@ config MMC_SDRICOH_CS

  config MMC_TMIO
       tristate "Toshiba Mobile IO Controller (TMIO) MMC/SD function support"
-       depends on MFD_TMIO
+       depends on MFD_TMIO || MFD_ASIC3
       help
         This provides support for the SD/MMC cell found in TC6393XB,
-         T7L66XB and also ipaq ASIC3
+         T7L66XB and also HTC ASIC3.

drivers/mmc/host/tmio_mmc.c +0 -0
index 9f6e180..9f68c2f 100644
@@ -10,7 +10,7 @@
  *
Quoted 10 lines
Quoted 8 lines
drivers/mmc/host/tmio_mmc.c +1 -1
  * Driver for the MMC / SD / SDIO cell found in:
  *
- * TC6393XB TC6391XB TC6387XB T7L66XB
+ * TC6393XB TC6391XB TC6387XB T7L66XB ASIC3
  *
  * This driver draws mainly on scattered spec sheets, Reverse engineering
  * of the toshiba e800  SD driver and some parts of the 2.4 ASIC3 driver

(4 bit

regards
Philipp

#13 lore raw
In reply to Philipp Zabel
Quoted 4 lines · On Thu, 4 Jun 2009 20:12:30 +0200 Philipp Zabel <[email protected]>…

I've broken the long lines in patches 1-3 and merged the fix into patch 2:
[PATCH 1/7] MFD,mmc: tmio_mmc: make HCLK configurable (v2) [PATCH 2/7] mmc: tmio_mmc: add bus_shift support (v2)
[PATCH 3/7] mmc: tmio_mmc: don't use set_irq_type (v2)

Quoted 9 lines

[PATCH 4/7] mmc: tmio_mmc: correct probe return value for num_resources != 3
Also I've added three new patches for your consideration. Patch 5 delays mapping of the SD control registers because mfd_cell->enable has to enable the RAM first. Patch 6 fixes a bug in the SDCLK divider calculation and patch 7 finally enables compilation of tmio_mmc for ASIC3:
[PATCH 5/7] mmc: tmio_mmc: map SD control registers after enabling the MFD cell [PATCH 6/7] mmc: tmio_mmc: fix SDCLK divider setting
[PATCH 7/7] mmc: tmio_mmc: allow compilation for ASIC3

I've queued up everything except patch 7 as I haven't seen Ian's response on that yet.

Rgds

Signature · 6 lines
     -- Pierre Ossman

  WARNING: This correspondence is being monitored by the
  Swedish government. Make sure your server uses encryption
  for SMTP traffic and consider using PGP for end-to-end
  encryption.
#14 lore raw
Quoted 2 lines · Pierre Ossman

I've queued up everything except patch 7 as I haven't seen Ian's response on that yet.

Is that using my replacement for patch 6 ? I didnt ack that one since (whilst correct) My solution is simpler and fixes another bug as well.

Patch 7 is Acked-by me now that Philipp has explained the idea behind it.

#15 lore raw
Quoted 8 lines · On Sat, 13 Jun 2009 19:42:25 +0100 Ian Molton <[email protected]> wrote:
Quoted 2 lines · Pierre Ossman

I've queued up everything except patch 7 as I haven't seen Ian's response on that yet.

Is that using my replacement for patch 6 ? I didnt ack that one since (whilst correct) My solution is simpler and fixes another bug as well.

I queued up your replacement, yes.

Quoted 1 line

Patch 7 is Acked-by me now that Philipp has explained the idea behind it.

Ok. I'll queue that up as well.

Rgds

Signature · 6 lines
     -- Pierre Ossman

  WARNING: This correspondence is being monitored by the
  Swedish government. Make sure your server uses encryption
  for SMTP traffic and consider using PGP for end-to-end
  encryption.
#16 lore raw
Quoted 1 line · Pierre Ossman

I queued up your replacement, yes.

Great,

Quoted 3 lines
Quoted 1 line

Patch 7 is Acked-by me now that Philipp has explained the idea behind it.

Ok. I'll queue that up as well.

Awesome, thanks,

-Ian