Skip to contentSkip to conversation

MIPS: Alchemy: get rid of superfluous UART definitions

PATCH In review Manuel Lauss 2 participants 3 messages Oct 15, 2009 MIPS

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 MIPS: Alchemy: get rid of superfluous UART definitions

Remove unused uart bit definitions and base macros.

---
Applies on top of the previous prom_putchar patch.

No functional changes observed. The UART0_ADDR macro is used by PM code but I'll get rid of that too, eventually.

 arch/mips/alchemy/common/platform.c        |   44 ++++++-------
 arch/mips/include/asm/mach-au1x00/au1000.h |   95 ----------------------------
 2 files changed, 21 insertions(+), 118 deletions(-)
arch/mips/alchemy/common/platform.c +21 -23
index 5a9a4f9..195e5b3 100644
@@ -20,38 +20,36 @@
 #include <asm/mach-au1x00/au1xxx_dbdma.h>
 #include <asm/mach-au1x00/au1100_mmc.h>
 
-#define PORT(_base, _irq)				\
-	{						\
-		.iobase		= _base,		\
-		.membase	= (void __iomem *)_base,\
-		.mapbase	= CPHYSADDR(_base),	\
-		.irq		= _irq,			\
-		.regshift	= 2,			\
-		.iotype		= UPIO_AU,		\
-		.flags		= UPF_SKIP_TEST 	\
+#define PORT(_base, _irq)					\
+	{							\
+		.mapbase	= _base,			\
+		.irq		= _irq,				\
+		.regshift	= 2,				\
+		.iotype		= UPIO_AU,			\
+		.flags		= UPF_SKIP_TEST | UPF_IOREMAP	\
 	}
 
 static struct plat_serial8250_port au1x00_uart_data[] = {
 #if defined(CONFIG_SERIAL_8250_AU1X00)
 #if defined(CONFIG_SOC_AU1000)
-	PORT(UART0_ADDR, AU1000_UART0_INT),
-	PORT(UART1_ADDR, AU1000_UART1_INT),
-	PORT(UART2_ADDR, AU1000_UART2_INT),
-	PORT(UART3_ADDR, AU1000_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1000_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1000_UART1_INT),
+	PORT(UART2_PHYS_ADDR, AU1000_UART2_INT),
+	PORT(UART3_PHYS_ADDR, AU1000_UART3_INT),
 #elif defined(CONFIG_SOC_AU1500)
-	PORT(UART0_ADDR, AU1500_UART0_INT),
-	PORT(UART3_ADDR, AU1500_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1500_UART0_INT),
+	PORT(UART3_PHYS_ADDR, AU1500_UART3_INT),
 #elif defined(CONFIG_SOC_AU1100)
-	PORT(UART0_ADDR, AU1100_UART0_INT),
-	PORT(UART1_ADDR, AU1100_UART1_INT),
-	PORT(UART3_ADDR, AU1100_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1100_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1100_UART1_INT),
+	PORT(UART3_PHYS_ADDR, AU1100_UART3_INT),
 #elif defined(CONFIG_SOC_AU1550)
-	PORT(UART0_ADDR, AU1550_UART0_INT),
-	PORT(UART1_ADDR, AU1550_UART1_INT),
-	PORT(UART3_ADDR, AU1550_UART3_INT),
+	PORT(UART0_PHYS_ADDR, AU1550_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1550_UART1_INT),
+	PORT(UART3_PHYS_ADDR, AU1550_UART3_INT),
 #elif defined(CONFIG_SOC_AU1200)
-	PORT(UART0_ADDR, AU1200_UART0_INT),
-	PORT(UART1_ADDR, AU1200_UART1_INT),
+	PORT(UART0_PHYS_ADDR, AU1200_UART0_INT),
+	PORT(UART1_PHYS_ADDR, AU1200_UART1_INT),
 #endif
 #endif	/* CONFIG_SERIAL_8250_AU1X00 */
 	{ },
arch/mips/include/asm/mach-au1x00/au1000.h +0 -95

137 lines not on this page · raw message

Signature · 1 line
1.6.5.rc2
#1 lore raw
Quoted 6 lines · Manuel Lauss

Remove unused uart bit definitions and base macros.

---
Applies on top of the previous prom_putchar patch.

...and depends on alchemy irq changes lmo-queue.

Manuel