MIPS: Alchemy: get rid of superfluous UART definitions
PATCH 1/1 MIPS: Alchemy: get rid of superfluous UART definitions
Remove unused uart bit definitions and base macros.
Signed-off-by Manuel Lauss <[email protected]>
---
Applies on top of the previous prom_putchar patch.
No functional changes observed. The UART0_ADDR macro is used by PM code but I'll get rid of that too, eventually.
arch/mips/alchemy/common/platform.c | 44 ++++++------- arch/mips/include/asm/mach-au1x00/au1000.h | 95 ---------------------------- 2 files changed, 21 insertions(+), 118 deletions(-)
arch/mips/alchemy/common/platform.c +21 -23
@@ -20,38 +20,36 @@#include <asm/mach-au1x00/au1xxx_dbdma.h> #include <asm/mach-au1x00/au1100_mmc.h> -#define PORT (_base, _irq) \ - { \ - .iobase = _base, \ - .membase = (void __iomem *)_base,\ - .mapbase = CPHYSADDR(_base), \ - .irq = _irq, \ - .regshift = 2, \ - .iotype = UPIO_AU, \ - .flags = UPF_SKIP_TEST \ +#define PORT (_base, _irq) \ + { \ + .mapbase = _base, \ + .irq = _irq, \ + .regshift = 2, \ + .iotype = UPIO_AU, \ + .flags = UPF_SKIP_TEST | UPF_IOREMAP \ } static struct plat_serial8250_port au1x00_uart_data[] = { #if defined(CONFIG_SERIAL_8250_AU1X00) #if defined(CONFIG_SOC_AU1000) - PORT(UART0_ADDR, AU1000_UART0_INT), - PORT(UART1_ADDR, AU1000_UART1_INT), - PORT(UART2_ADDR, AU1000_UART2_INT), - PORT(UART3_ADDR, AU1000_UART3_INT), + PORT(UART0_PHYS_ADDR, AU1000_UART0_INT), + PORT(UART1_PHYS_ADDR, AU1000_UART1_INT), + PORT(UART2_PHYS_ADDR, AU1000_UART2_INT), + PORT(UART3_PHYS_ADDR, AU1000_UART3_INT), #elif defined(CONFIG_SOC_AU1500) - PORT(UART0_ADDR, AU1500_UART0_INT), - PORT(UART3_ADDR, AU1500_UART3_INT), + PORT(UART0_PHYS_ADDR, AU1500_UART0_INT), + PORT(UART3_PHYS_ADDR, AU1500_UART3_INT), #elif defined(CONFIG_SOC_AU1100) - PORT(UART0_ADDR, AU1100_UART0_INT), - PORT(UART1_ADDR, AU1100_UART1_INT), - PORT(UART3_ADDR, AU1100_UART3_INT), + PORT(UART0_PHYS_ADDR, AU1100_UART0_INT), + PORT(UART1_PHYS_ADDR, AU1100_UART1_INT), + PORT(UART3_PHYS_ADDR, AU1100_UART3_INT), #elif defined(CONFIG_SOC_AU1550) - PORT(UART0_ADDR, AU1550_UART0_INT), - PORT(UART1_ADDR, AU1550_UART1_INT), - PORT(UART3_ADDR, AU1550_UART3_INT), + PORT(UART0_PHYS_ADDR, AU1550_UART0_INT), + PORT(UART1_PHYS_ADDR, AU1550_UART1_INT), + PORT(UART3_PHYS_ADDR, AU1550_UART3_INT), #elif defined(CONFIG_SOC_AU1200) - PORT(UART0_ADDR, AU1200_UART0_INT), - PORT(UART1_ADDR, AU1200_UART1_INT), + PORT(UART0_PHYS_ADDR, AU1200_UART0_INT), + PORT(UART1_PHYS_ADDR, AU1200_UART1_INT), #endif #endif /* CONFIG_SERIAL_8250_AU1X00 */ { },
arch/mips/include/asm/mach-au1x00/au1000.h +0 -95
137 lines not on this page · raw message
Signature · 1 line
1.6.5.rc2
Quoted 6 lines · Manuel Lauss
Remove unused uart bit definitions and base macros.
Signed-off-by Manuel Lauss <[email protected]>---
Applies on top of the previousprom_putcharpatch.
...and depends on alchemy irq changes lmo-queue.
Manuel
On Thu, Oct 15, 2009 at 07:07:34PM +0200, Manuel Lauss wrote:
Queued for 2.6.33,
Ralf