PXA DMA-capable PATA driver
Subsystems (4)
PATCH v4 1/1 PXA DMA-capable PATA driver
This patch adds a driver for a harddrive attached to PXA address and data bus. Unlike pata_platform, this driver allows usage of PXA DMA controller, making the transmission speed 3x higher.
Signed-off-by Marek Vasut <[email protected]>
Acked-by Jeff Garzik <[email protected]>
--- arch/arm/mach-pxa/include/mach/pata_pxa.h | 33 +++ drivers/ata/Kconfig | 11 + drivers/ata/Makefile | 1 + drivers/ata/pata_pxa.c | 411 +++++++++++++++++++++++++++++ 4 files changed, 456 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-pxa/include/mach/pata_pxa.h create mode 100644 drivers/ata/pata_pxa.c
arch/arm/mach-pxa/include/mach/pata_pxa.h new file +33 -0
@@ -0,0 +1,33 @@ +/* +* Generic PXA PATA driver +* +* Copyright (C) 2010 Marek Vasut <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2, or (at your option) +* any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; see the file COPYING. If not, write to +* the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +#ifndef __MACH_PATA_PXA_H__ +#define __MACH_PATA_PXA_H__ + +struct pata_pxa_pdata { +/* PXA DMA DREQ<0:2> pin */ +uint32_t dma_dreq; +/* Register shift */ +uint32_t reg_shift; +/* IRQ flags */ +uint32_t irq_flags; +}; + +#endif /* __MACH_PATA_PXA_H__ */
drivers/ata/Kconfig +11 -0
@@ -684,6 +684,17 @@ config PATA_VIA If unsure, say N. +config PATA_PXA + tristate "PXA DMA-capable PATA support" + depends on ARCH_PXA + help + This option enables support for harddrive attached to PXA CPU's bus. + + NOTE: This driver utilizes PXA DMA controller, in case your hardware + is not capable of doing MWDMA, use pata_platform instead. + + If unsure, say N. + config PATA_WINBOND tristate "Winbond SL82C105 PATA support" depends on PCI
drivers/ata/Makefile +1 -0
@@ -79,6 +79,7 @@ obj-$(CONFIG_PATA_PLATFORM) += pata_platform.o obj-$(CONFIG_PATA_AT91) += pata_at91.o obj-$(CONFIG_PATA_OF_PLATFORM) += pata_of_platform.o obj-$(CONFIG_PATA_ICSIDE) += pata_icside.o +obj-$(CONFIG_PATA_PXA) += pata_pxa.o # Should be last but two libata driver obj-$(CONFIG_PATA_ACPI) += pata_acpi.o # Should be last but one libata driver
drivers/ata/pata_pxa.c new file +411 -0
411 lines not on this page · raw message
Signature · 1 line
1.7.0