Skip to contentSkip to conversation

net: Implement Any-IP support for IPv6.

PATCH In review Maciej Żenczykowski 2 participants 5 messages Sep 27, 2010 – Sep 29, 2010

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 net: Implement Any-IP support for IPv6.

From: Maciej Żenczykowski <[email protected]>

AnyIP is the capability to receive packets and establish incoming connections on IPs we have not explicitly configured on the machine.

An example use case is to configure a machine to accept all incoming traffic on eth0, and leave the policy of whether traffic for a given IP should be delivered to the machine up to the load balancer.

Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)

---
 net/ipv6/route.c |   10 +++++++++-
 1 files changed, 9 insertions(+), 1 deletions(-)
net/ipv6/route.c +9 -1
index d126365..3a74f90 100644
@@ -1169,6 +1169,8 @@ int ip6_route_add(struct fib6_config *cfg)
 
 	if (addr_type & IPV6_ADDR_MULTICAST)
 		rt->dst.input = ip6_mc_input;
+	else if (cfg->fc_flags & RTF_LOCAL)
+		rt->dst.input = ip6_input;
 	else
 		rt->dst.input = ip6_forward;
 
@@ -1190,7 +1192,8 @@ int ip6_route_add(struct fib6_config *cfg)
 	   they would result in kernel looping; promote them to reject routes
 	 */
 	if ((cfg->fc_flags & RTF_REJECT) ||
-	    (dev && (dev->flags&IFF_LOOPBACK) && !(addr_type&IPV6_ADDR_LOOPBACK))) {
+	    (dev && (dev->flags&IFF_LOOPBACK) && !(addr_type&IPV6_ADDR_LOOPBACK)
+					      && !(cfg->fc_flags&RTF_LOCAL))) {
 		/* hold loopback dev/idev if we haven't done so. */
 		if (dev != net->loopback_dev) {
 			if (dev) {
@@ -2082,6 +2085,9 @@ static int rtm_to_fib6_config(struct sk_buff *skb, struct nlmsghdr *nlh,
 	if (rtm->rtm_type == RTN_UNREACHABLE)
 		cfg->fc_flags |= RTF_REJECT;
 
+	if (rtm->rtm_type == RTN_LOCAL)
+		cfg->fc_flags |= RTF_LOCAL;
+
 	cfg->fc_nlinfo.pid = NETLINK_CB(skb).pid;
 	cfg->fc_nlinfo.nlh = nlh;
 	cfg->fc_nlinfo.nl_net = sock_net(skb->sk);
@@ -2202,6 +2208,8 @@ static int rt6_fill_node(struct net *net,
 	NLA_PUT_U32(skb, RTA_TABLE, table);
 	if (rt->rt6i_flags&RTF_REJECT)
 		rtm->rtm_type = RTN_UNREACHABLE;
+	else if (rt->rt6i_flags&RTF_LOCAL)
+		rtm->rtm_type = RTN_LOCAL;
 	else if (rt->rt6i_dev && (rt->rt6i_dev->flags&IFF_LOOPBACK))
 		rtm->rtm_type = RTN_LOCAL;
 	else
Signature · 1 line
1.7.2.3
maintainer
#1 lore raw

From: Maciej Żenczykowski <[email protected]>
Date: Mon, 27 Sep 2010 03:07:02 -0700

Quoted 9 lines

From: Maciej Żenczykowski <[email protected]>

AnyIP is the capability to receive packets and establish incoming connections on IPs we have not explicitly configured on the machine.

An example use case is to configure a machine to accept all incoming traffic on eth0, and leave the policy of whether traffic for a given IP should be delivered to the machine up to the load balancer.

Quoted 6 lines

Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)

Does this already work on the ipv4 side?

If not, why only add it to ipv6?

maintainer
#3 lore raw

From: Maciej Żenczykowski <[email protected]>
Date: Tue, 28 Sep 2010 14:04:47 -0700

Quoted 5 lines

AFAIK, Tom Herbert did post the ipv4 patch some time back.

http://patchwork.ozlabs.org/patch/53381/

I think the ipv6 code path (and hence the patch itself) is much cleaner.

Ok, I've moved that patch back to under-review state, maybe we can get them both in at the same time.

Thanks.

maintainer
#4 lore raw
In reply to Maciej Żenczykowski

From: Maciej Żenczykowski <[email protected]>
Date: Mon, 27 Sep 2010 03:07:02 -0700

Quoted 9 lines

From: Maciej Żenczykowski <[email protected]>

AnyIP is the capability to receive packets and establish incoming connections on IPs we have not explicitly configured on the machine.

An example use case is to configure a machine to accept all incoming traffic on eth0, and leave the policy of whether traffic for a given IP should be delivered to the machine up to the load balancer.

Quoted 6 lines

Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)

Ok, I applied this and Tom's ipv4-side patch and pushed it all out to net-next-2.6

Thanks!