net: Implement Any-IP support for IPv6.
Subsystems (3)
PATCH 1/1 net: Implement Any-IP support for IPv6.
From: Maciej Żenczykowski <[email protected]>
AnyIP is the capability to receive packets and establish incoming connections on IPs we have not explicitly configured on the machine.
An example use case is to configure a machine to accept all incoming traffic on eth0, and leave the policy of whether traffic for a given IP should be delivered to the machine up to the load balancer.
Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)
--- net/ipv6/route.c | 10 +++++++++- 1 files changed, 9 insertions(+), 1 deletions(-)
net/ipv6/route.c +9 -1
@@ -1169,6 +1169,8 @@ int ip6_route_add(struct fib6_config *cfg)if (addr_type &IPV6_ADDR_MULTICAST ) rt->dst.input = ip6_mc_input; +else if (cfg->fc_flags &RTF_LOCAL ) + rt->dst.input = ip6_input;else rt->dst.input = ip6_forward;
@@ -1190,7 +1192,8 @@ int ip6_route_add(struct fib6_config *cfg)they would result in kernel looping; promote them to reject routes */ if ((cfg->fc_flags &RTF_REJECT ) || - (dev && (dev->flags&IFF_LOOPBACK ) && !(addr_type&IPV6_ADDR_LOOPBACK ))) { + (dev && (dev->flags&IFF_LOOPBACK ) && !(addr_type&IPV6_ADDR_LOOPBACK ) + && !(cfg->fc_flags&RTF_LOCAL ))) {/* hold loopback dev/idev if we haven't done so. */ if (dev != net->loopback_dev) {if (dev) {
@@ -2082,6 +2085,9 @@ static int rtm_to_fib6_config(struct sk_buff *skb, struct nlmsghdr *nlh,if (rtm->rtm_type ==RTN_UNREACHABLE ) cfg->fc_flags |=RTF_REJECT ; +if (rtm->rtm_type ==RTN_LOCAL ) + cfg->fc_flags |=RTF_LOCAL ; + cfg->fc_nlinfo.pid =NETLINK_CB (skb).pid; cfg->fc_nlinfo.nlh = nlh; cfg->fc_nlinfo.nl_net =sock_net (skb->sk);
@@ -2202,6 +2208,8 @@ static int rt6_fill_node(struct net *net,NLA_PUT_U32 (skb,RTA_TABLE , table);if (rt->rt6i_flags&RTF_REJECT ) rtm->rtm_type =RTN_UNREACHABLE ; +else if (rt->rt6i_flags&RTF_LOCAL ) + rtm->rtm_type =RTN_LOCAL ;else if (rt->rt6i_dev && (rt->rt6i_dev->flags&IFF_LOOPBACK )) rtm->rtm_type =RTN_LOCAL ;else
Signature · 1 line
1.7.2.3
David Miller
maintainerFrom: Maciej Żenczykowski <[email protected]>
Date: Mon, 27 Sep 2010 03:07:02 -0700
Quoted 9 lines
From: Maciej Żenczykowski <[email protected]>
AnyIP is the capability to receive packets and establish incoming connections on IPs we have not explicitly configured on the machine.
An example use case is to configure a machine to accept all incoming traffic on eth0, and leave the policy of whether traffic for a given IP should be delivered to the machine up to the load balancer.
Quoted 6 lines
Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)Signed-off-by Maciej Żenczykowski <[email protected]>
Does this already work on the ipv4 side?
If not, why only add it to ipv6?
AFAIK, Tom Herbert did post the ipv4 patch some time back.
http://patchwork.ozlabs.org/patch/53381/
I think the ipv6 code path (and hence the patch itself) is much cleaner.
David Miller
maintainerFrom: Maciej Żenczykowski <[email protected]>
Date: Tue, 28 Sep 2010 14:04:47 -0700
Quoted 5 lines
AFAIK, Tom Herbert did post the ipv4 patch some time back.
http://patchwork.ozlabs.org/patch/53381/
I think the ipv6 code path (and hence the patch itself) is much cleaner.
Ok, I've moved that patch back to under-review state, maybe we can get them both in at the same time.
Thanks.
David Miller
maintainerFrom: Maciej Żenczykowski <[email protected]>
Date: Mon, 27 Sep 2010 03:07:02 -0700
Quoted 9 lines
From: Maciej Żenczykowski <[email protected]>
AnyIP is the capability to receive packets and establish incoming connections on IPs we have not explicitly configured on the machine.
An example use case is to configure a machine to accept all incoming traffic on eth0, and leave the policy of whether traffic for a given IP should be delivered to the machine up to the load balancer.
Quoted 6 lines
Can be setup as follows:
ip -6 rule from all iif eth0 lookup 200
ip -6 route add local default dev lo table 200
(in this case for all IPv6 addresses)Signed-off-by Maciej Żenczykowski <[email protected]>
Ok, I applied this and Tom's ipv4-side patch and pushed it all out to net-next-2.6
Thanks!