Add initial support for OMAP3 IGEP module
Subsystems (3)
v3 cover Add initial support for OMAP3 IGEP module
Hello,
This is the version 3 of patch series to introduce the OMAP3 IGEP module support.
Changes since v2 (thanks Laurent):
- Set onenand_setup to NULL instead of adding a no-op function.
- On igep3_flash_init() function:
- Use 'for' loop instead 'while' loop.
- No need to initialize ret to 0, we're assigning it right after.
- No need to check for onenandcs < GPMC_CS_NUM, it will always be true.
- omap_board_config_size is implicitly initialized to 0 in plat-omap/common.c, get_config() won't dereference omap_board_config, so we can remove the empty igep2_config array.
Changes since v1:
- add DEBUG_LL/EARLY_PRINTK entry
arch/arm/mach-omap2/Kconfig | 5 + arch/arm/mach-omap2/Makefile | 2 + arch/arm/mach-omap2/board-igep0030.c | 401 ++++++++++++++++++++++++++ arch/arm/plat-omap/include/plat/uncompress.h | 1 + 4 files changed, 409 insertions(+), 0 deletions(-)
PATCH v3 1/1 omap3: Add minimal OMAP3 IGEP module support.
The OMAP3 IGEP module is a low-power, high performance production-ready system-on-module (SOM) based on TI's OMAP3 family. More about this board at www.igep.es.
--- arch/arm/mach-omap2/Kconfig | 5 + arch/arm/mach-omap2/Makefile | 2 + arch/arm/mach-omap2/board-igep0030.c | 401 ++++++++++++++++++++++++++ arch/arm/plat-omap/include/plat/uncompress.h | 1 + 4 files changed, 409 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-omap2/board-igep0030.c
arch/arm/mach-omap2/Kconfig +5 -0
@@ -220,6 +220,11 @@ config MACH_IGEP0020 default y select OMAP_PACKAGE_CBB +config MACH_IGEP0030 + bool "IGEP OMAP3 module" + depends on ARCH_OMAP3 + select OMAP_PACKAGE_CBB + config MACH_SBC3530 bool "OMAP3 SBC STALKER board" depends on ARCH_OMAP3
arch/arm/mach-omap2/Makefile +2 -0
@@ -148,6 +148,8 @@ obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \ hsmmc.o obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o \ hsmmc.o +obj-$(CONFIG_MACH_IGEP0030) += board-igep0030.o \ + hsmmc.o obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK) += board-omap3touchbook.o \ hsmmc.o obj-$(CONFIG_MACH_OMAP_4430SDP) += board-4430sdp.o \
arch/arm/mach-omap2/board-igep0030.c new file +401 -0
401 lines not on this page · raw message
arch/arm/plat-omap/include/plat/uncompress.h +1 -0
@@ -143,6 +143,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)/* omap3 based boards using UART3 */ DEBUG_LL_OMAP3 (3 , cm_t35);DEBUG_LL_OMAP3 (3 , igep0020); +DEBUG_LL_OMAP3 (3 , igep0030);DEBUG_LL_OMAP3 (3 , nokia_rx51);DEBUG_LL_OMAP3 (3 , omap3517evm);DEBUG_LL_OMAP3 (3 , omap3_beagle);
Signature · 1 line
1.7.0.4
Tony Lindgren
maintainerPATCH v3 1/1 omap3: Add minimal OMAP3 IGEP module support.
Quoted 3 lines · Enric Balletbo i Serra
The OMAP3 IGEP module is a low-power, high performance production-ready system-on-module (SOM) based on TI's OMAP3 family. More about this board at www.igep.es.
Adding this to omap-for-linus. Updated it for to use MMC caps instead of wires and to be selected by default in Kconfig.
Regards,
Tony