Skip to contentSkip to conversation

Add initial support for OMAP3 IGEP module

PATCH New Enric Balletbo i Serra 2 participants 3 messages Oct 2, 2010 – Oct 5, 2010

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v3 cover Add initial support for OMAP3 IGEP module

Hello,

This is the version 3 of patch series to introduce the OMAP3 IGEP module support.

Changes since v2 (thanks Laurent):
- Set onenand_setup to NULL instead of adding a no-op function.
- On igep3_flash_init() function:
- Use 'for' loop instead 'while' loop.
- No need to initialize ret to 0, we're assigning it right after.
- No need to check for onenandcs < GPMC_CS_NUM, it will always be true.
- omap_board_config_size is implicitly initialized to 0 in plat-omap/common.c, get_config() won't dereference omap_board_config, so we can remove the empty igep2_config array.

Changes since v1:
- add DEBUG_LL/EARLY_PRINTK entry

 arch/arm/mach-omap2/Kconfig                  |    5 +
 arch/arm/mach-omap2/Makefile                 |    2 +
 arch/arm/mach-omap2/board-igep0030.c         |  401 ++++++++++++++++++++++++++
 arch/arm/plat-omap/include/plat/uncompress.h |    1 +
 4 files changed, 409 insertions(+), 0 deletions(-)
#1 lore raw

PATCH v3 1/1 omap3: Add minimal OMAP3 IGEP module support.

The OMAP3 IGEP module is a low-power, high performance production-ready system-on-module (SOM) based on TI's OMAP3 family. More about this board at www.igep.es.

---
 arch/arm/mach-omap2/Kconfig                  |    5 +
 arch/arm/mach-omap2/Makefile                 |    2 +
 arch/arm/mach-omap2/board-igep0030.c         |  401 ++++++++++++++++++++++++++
 arch/arm/plat-omap/include/plat/uncompress.h |    1 +
 4 files changed, 409 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/mach-omap2/board-igep0030.c
arch/arm/mach-omap2/Kconfig +5 -0
index b48bacf..233bfbe 100644
@@ -220,6 +220,11 @@ config MACH_IGEP0020
 	default y
 	select OMAP_PACKAGE_CBB
 
+config MACH_IGEP0030
+	bool "IGEP OMAP3 module"
+	depends on ARCH_OMAP3
+	select OMAP_PACKAGE_CBB
+
 config MACH_SBC3530
 	bool "OMAP3 SBC STALKER board"
 	depends on ARCH_OMAP3
arch/arm/mach-omap2/Makefile +2 -0
index 88d3a1e..71386d4 100644
@@ -148,6 +148,8 @@ obj-$(CONFIG_MACH_CM_T35)		+= board-cm-t35.o \
 					   hsmmc.o
 obj-$(CONFIG_MACH_IGEP0020)		+= board-igep0020.o \
 					   hsmmc.o
+obj-$(CONFIG_MACH_IGEP0030)		+= board-igep0030.o \
+					   hsmmc.o
 obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK)	+= board-omap3touchbook.o \
 					   hsmmc.o
 obj-$(CONFIG_MACH_OMAP_4430SDP)		+= board-4430sdp.o \
arch/arm/mach-omap2/board-igep0030.c new file +401 -0

401 lines not on this page · raw message

arch/arm/plat-omap/include/plat/uncompress.h +1 -0
index ddf723b..2601ff4 100644
@@ -143,6 +143,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id)
 		/* omap3 based boards using UART3 */
 		DEBUG_LL_OMAP3(3, cm_t35);
 		DEBUG_LL_OMAP3(3, igep0020);
+		DEBUG_LL_OMAP3(3, igep0030);
 		DEBUG_LL_OMAP3(3, nokia_rx51);
 		DEBUG_LL_OMAP3(3, omap3517evm);
 		DEBUG_LL_OMAP3(3, omap3_beagle);
Signature · 1 line
1.7.0.4
maintainer
#2 lore raw

PATCH v3 1/1 omap3: Add minimal OMAP3 IGEP module support.

Quoted 3 lines · Enric Balletbo i Serra

The OMAP3 IGEP module is a low-power, high performance production-ready system-on-module (SOM) based on TI's OMAP3 family. More about this board at www.igep.es.

Adding this to omap-for-linus. Updated it for to use MMC caps instead of wires and to be selected by default in Kconfig.

Regards,

Tony