Skip to contentSkip to conversation

Add Marvell New Soc Support ARMADA100

PATCH Superseded Prafulla Wadaskar 3 participants 11 messages Oct 27, 2010 – Oct 28, 2010

Subsystems (2)

v1 of 4 Superseded Latest is v4 →

lore
Share & tools
lore
#0 lore raw

cover Add Marvell New Soc Support ARMADA100

This patch series adds basic ARMADA100 support, with minimal drivers (UART, MFP) support and Aspenite-DB board support for simple boot

Prafulla WADASKAR (3):
arm: Add Support for Marvell ARMADA 100 Familiy SoCs.
Serial: Add UART support for Marvell ARMADA 100 SoCs.
Armada100: Add Board Support for Marvell Aspenite-DB

Prafulla Wadaskar (2):
gpio: Add Multu-Function-Pin configuration driver for Marvell SoCs add mfp configuration support for ARMADA100

 MAINTAINERS                                     |    1 +
 MAKEALL                                         |    1 +
 arch/arm/cpu/arm926ejs/armada100/Makefile       |   46 +++++
 arch/arm/cpu/arm926ejs/armada100/cpu.c          |   92 ++++++++++
 arch/arm/cpu/arm926ejs/armada100/dram.c         |  122 +++++++++++++
 arch/arm/cpu/arm926ejs/armada100/timer.c        |  199 +++++++++++++++++++++
 arch/arm/include/asm/arch-armada100/armada100.h |  120 +++++++++++++
 arch/arm/include/asm/arch-armada100/cpu.h       |   53 ++++++
 arch/arm/include/asm/arch-armada100/mfp.h       |  218 +++++++++++++++++++++++
 board/Marvell/aspenite/Makefile                 |   52 ++++++
 board/Marvell/aspenite/aspenite.c               |   53 ++++++
 board/Marvell/aspenite/config.mk                |   26 +++
 boards.cfg                                      |    1 +
 drivers/gpio/Makefile                           |    1 +
 drivers/gpio/mfp.c                              |  105 +++++++++++
 drivers/serial/ns16550.c                        |   16 ++
 drivers/serial/serial.c                         |    3 +
 include/configs/aspenite.h                      |  133 ++++++++++++++
 include/mfp.h                                   |   97 ++++++++++
 19 files changed, 1339 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/timer.c
 create mode 100644 arch/arm/include/asm/arch-armada100/armada100.h
 create mode 100644 arch/arm/include/asm/arch-armada100/cpu.h
 create mode 100755 arch/arm/include/asm/arch-armada100/mfp.h
 create mode 100644 board/Marvell/aspenite/Makefile
 create mode 100644 board/Marvell/aspenite/aspenite.c
 create mode 100644 board/Marvell/aspenite/config.mk
 create mode 100644 drivers/gpio/mfp.c
 create mode 100644 include/configs/aspenite.h
 create mode 100644 include/mfp.h
Signature · 1 line
1.7.2.1
#1 lore raw

PATCH 1/5 arm: Add Support for Marvell ARMADA 100 Familiy SoCs.

From: Prafulla WADASKAR <[email protected]>

ARMADA 100 Family processors are highly integrated SoCs based on Sheeva_88SV331x-v5 PJ1 cpu core.
Ref: http://www.marvell.com/products/processors/applications/armada_100

SoC versions Supported:
1) ARMADA168/88AP168 (Aspen P)
2) ARMADA166/88AP166 (Aspen M)
3) ARMADA162/88AP162 (Aspen L)

Contributors:
Eric Miao <[email protected]>
Lei Wen <[email protected]>
Mahavir Jain <[email protected]>

---
 arch/arm/cpu/arm926ejs/armada100/Makefile       |   46 ++++++
 arch/arm/cpu/arm926ejs/armada100/cpu.c          |   92 +++++++++++
 arch/arm/cpu/arm926ejs/armada100/dram.c         |  122 ++++++++++++++
 arch/arm/cpu/arm926ejs/armada100/timer.c        |  199 +++++++++++++++++++++++
 arch/arm/include/asm/arch-armada100/armada100.h |  120 ++++++++++++++
 arch/arm/include/asm/arch-armada100/cpu.h       |   53 ++++++
 6 files changed, 632 insertions(+), 0 deletions(-)
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/Makefile
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/cpu.c
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/dram.c
 create mode 100644 arch/arm/cpu/arm926ejs/armada100/timer.c
 create mode 100644 arch/arm/include/asm/arch-armada100/armada100.h
 create mode 100644 arch/arm/include/asm/arch-armada100/cpu.h
arch/arm/cpu/arm926ejs/armada100/Makefile new file +46 -0
new file mode 100644
index 0000000..6403bf4
@@ -0,0 +1,46 @@
+#
+# (C) Copyright 2010
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(SOC).a
+
+COBJS-y	= cpu.o timer.o dram.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS	:= $(addprefix $(obj),$(SOBJS) $(COBJS-y))
+
+all:	$(obj).depend $(LIB)
+
+$(LIB):	$(OBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
arch/arm/cpu/arm926ejs/armada100/cpu.c new file +92 -0

92 lines not on this page · raw message

arch/arm/cpu/arm926ejs/armada100/dram.c new file +122 -0

122 lines not on this page · raw message

arch/arm/cpu/arm926ejs/armada100/timer.c new file +199 -0

199 lines not on this page · raw message

arch/arm/include/asm/arch-armada100/armada100.h new file +120 -0

120 lines not on this page · raw message

arch/arm/include/asm/arch-armada100/cpu.h new file +53 -0

53 lines not on this page · raw message

Signature · 1 line
1.7.2.1
#2 lore raw

PATCH 2/5 Serial: Add UART support for Marvell ARMADA 100 SoCs.

From: Prafulla WADASKAR <[email protected]>

ARMADA 100 SoCs has NS16550 compatible UART peripheral This patch enables the same for ARMADA100 platforms

---
 drivers/serial/ns16550.c |   16 ++++++++++++++++
 drivers/serial/serial.c  |    3 +++
 2 files changed, 19 insertions(+), 0 deletions(-)
drivers/serial/ns16550.c +16 -0
index 32f24de..e57ed1f 100644
@@ -26,7 +26,15 @@
 
 void NS16550_init (NS16550_t com_port, int baud_divisor)
 {
+#ifdef CONFIG_ARMADA100
+	/*
+	 * For ARMADA 100 Based Processors bit 6 in IER register
+	 * represents UART Unit Enable bit.
+	 */
+	serial_out((1 << 6), &com_port->ier);
+#else
 	serial_out(0x00, &com_port->ier);
+#endif
 #if defined(CONFIG_OMAP) && !defined(CONFIG_OMAP3_ZOOM2)
 	serial_out(0x7, &com_port->mdr1);	/* mode select reset TL16C750*/
 #endif
@@ -52,7 +60,15 @@ void NS16550_init (NS16550_t com_port, int baud_divisor)
 #ifndef CONFIG_NS16550_MIN_FUNCTIONS
 void NS16550_reinit (NS16550_t com_port, int baud_divisor)
 {
+#ifdef CONFIG_ARMADA100
+	/*
+	 * For ARMADA 100 Based Processors bit 6 in IER register
+	 * represents UART Unit Enable bit.
+	 */
+	serial_out((1 << 6), &com_port->ier);
+#else
 	serial_out(0x00, &com_port->ier);
+#endif
 	serial_out(UART_LCR_BKSE | UART_LCRVAL, &com_port->lcr);
 	serial_out(0, &com_port->dll);
 	serial_out(0, &com_port->dlm);
drivers/serial/serial.c +3 -0
index 1073ac0..f9a964e 100644
@@ -33,6 +33,9 @@
 #ifdef CONFIG_ORION5X
 #include <asm/arch/orion5x.h>
 #endif
+#ifdef CONFIG_ARMADA100
+#include <asm/arch/armada100.h>
+#endif
 
 #if defined (CONFIG_SERIAL_MULTI)
 #include <serial.h>
Signature · 1 line
1.7.2.1
#3 lore raw

PATCH 2/5 Serial: Add UART support for Marvell ARMADA 100 SoCs.

Hi Prafulla,

Quoted 17 lines · On Wednesday 27 October 2010 15:53:21 Prafulla Wadaskar wrote:

ARMADA 100 SoCs has NS16550 compatible UART peripheral This patch enables the same for ARMADA100 platforms

---
 drivers/serial/ns16550.c |   16 ++++++++++++++++
 drivers/serial/serial.c  |    3 +++
 2 files changed, 19 insertions(+), 0 deletions(-)
drivers/serial/ns16550.c +0 -0
index 32f24de..e57ed1f 100644
@@ -26,7 +26,15 @@
 
 void NS16550_init (NS16550_t com_port, int baud_divisor)

drivers/serial/ns16550.c line 37

Quoted 10 lines
drivers/serial/ns16550.c +8 -0
 {
+#ifdef CONFIG_ARMADA100
+	/*
+	 * For ARMADA 100 Based Processors bit 6 in IER register
+	 * represents UART Unit Enable bit.
+	 */
+	serial_out((1 << 6), &com_port->ier);
+#else
 	serial_out(0x00, &com_port->ier);
+#endif

These board/platform specific driver additions are really ugly. A better way to do this would be something like this:

Add this to your board/platform header:

#define CONFIG_SYS_NS16550_IER (1 << 6)

And then to ns16550.c or even ns16550.h:

#ifndef CONFIG_SYS_NS16550_IER
#define CONFIG_SYS_NS16550_IER 0x00
#endif

This macro can now be used unconditionally when initializing this "ier" register:

  	serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);

Cheers,
Stefan

--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-0 Fax: (+49)-8142-66989-80 Email: office at denx.de

#4 lore raw

PATCH 2/5 Serial: Add UART support for Marvell ARMADA 100 SoCs.

Quoted 51 lines

-----Original Message-----
From: Stefan Roese [mailto:sr at denx.de]
Sent: Wednesday, October 27, 2010 3:24 PM
To: u-boot at lists.denx.de; Prabhanjan Sarnaik
Cc: Prafulla Wadaskar; Manas Saksena; Lei Wen; Eric Miao
Subject: Re: [U-Boot] [PATCH 2/5] Serial: Add UART support for Marvell ARMADA 100 SoCs.

Hi Prafulla,

Quoted 17 lines · On Wednesday 27 October 2010 15:53:21 Prafulla Wadaskar wrote:

ARMADA 100 SoCs has NS16550 compatible UART peripheral This patch enables the same for ARMADA100 platforms

---
 drivers/serial/ns16550.c |   16 ++++++++++++++++
 drivers/serial/serial.c  |    3 +++
 2 files changed, 19 insertions(+), 0 deletions(-)
drivers/serial/ns16550.c +0 -0
index 32f24de..e57ed1f 100644
@@ -26,7 +26,15 @@
 
 void NS16550_init (NS16550_t com_port, int baud_divisor)

drivers/serial/ns16550.c line 37

Quoted 10 lines
drivers/serial/ns16550.c +8 -0
 {
+#ifdef CONFIG_ARMADA100
+	/*
+	 * For ARMADA 100 Based Processors bit 6 in IER register
+	 * represents UART Unit Enable bit.
+	 */
+	serial_out((1 << 6), &com_port->ier);
+#else
 	serial_out(0x00, &com_port->ier);
+#endif

These board/platform specific driver additions are really ugly. A better way
to do this would be something like this:

Add this to your board/platform header:

#define CONFIG_SYS_NS16550_IER (1 << 6)

And then to ns16550.c or even ns16550.h:

Quoted 8 lines

#ifndef CONFIG_SYS_NS16550_IER
#define CONFIG_SYS_NS16550_IER 0x00
#endif

This macro can now be used unconditionally when initializing this "ier" register:

  	serial_out(CONFIG_SYS_NS16550_IER, &com_port->ier);

Thanks...
I will do it for next version post.

Regards..
Prafulla . .

#5 lore raw

PATCH 3/5 gpio: Add Multi-Function-Pin configuration driver for Marvell SoCs

In reply to Prafulla Wadaskar

Most of the Marvell SoCs has Multi Function Pin (MFP) configuration registers For ex. ARMADA100.

These registers are programmed to expose the specific functionality associated with respective SoC Pins

This driver provides configuration APIs,
using them, configuration need to be done in board specific code

for ex- following code configures MFPs 107 and 108 for UART_TX/RX functionality

int board_early_init_f(void)

{
	u32 mfp_cfg[] = {
		/* Console on UART1 */
		MFP107_UART1_RXD,
		MFP108_UART1_TXD,
		MFP_EOC		/*End of configureation*/
	};
	/* configure MFP's */
	mfp_config(mfp_cfg);
	return 0;
}
---
 drivers/gpio/Makefile |    1 +
 drivers/gpio/mfp.c    |  105 +++++++++++++++++++++++++++++++++++++++++++++++++
 include/mfp.h         |   97 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 203 insertions(+), 0 deletions(-)
 create mode 100644 drivers/gpio/mfp.c
 create mode 100644 include/mfp.h
drivers/gpio/Makefile +1 -0
index a0f4552..7590b22 100644
@@ -27,6 +27,7 @@ LIB 	:= $(obj)libgpio.a
 
 COBJS-$(CONFIG_AT91_GPIO)	+= at91_gpio.o
 COBJS-$(CONFIG_KIRKWOOD_GPIO)	+= kw_gpio.o
+COBJS-$(CONFIG_MFP)		+= mfp.o
 COBJS-$(CONFIG_MXC_GPIO)	+= mxc_gpio.o
 COBJS-$(CONFIG_PCA953X)		+= pca953x.o
 COBJS-$(CONFIG_S5P)		+= s5p_gpio.o
drivers/gpio/mfp.c new file +105 -0

105 lines not on this page · raw message

include/mfp.h new file +97 -0

97 lines not on this page · raw message

Signature · 1 line
1.7.2.1
#6 lore raw

PATCH 4/5 add Multi Fnction Pin configuration support for ARMADA100

This patch adds the support MFP support for Marvell ARMADA100 SoCs

---
 arch/arm/include/asm/arch-armada100/mfp.h |  218 +++++++++++++++++++++++++++++
 1 files changed, 218 insertions(+), 0 deletions(-)
 create mode 100755 arch/arm/include/asm/arch-armada100/mfp.h
arch/arm/include/asm/arch-armada100/mfp.h new file +218 -0
new file mode 100755
index 0000000..eddcef7
@@ -0,0 +1,218 @@
+/*
+ * Based on linux/arch/arm/mach-mpp/include/mfp-pxa168.h
+ * (C) Copyright 2007
+ * Marvell Semiconductor <www.marvell.com>
+ * 2007-08-21: eric miao <[email protected]>
+ *
+ * (C) Copyright 2010
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <[email protected]>
+ * Contributor: Mahavir Jain <[email protected]>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __ARMADA100_MFP_H
+#define __ARMADA100_MFP_H
+
+/* By default Pin Drive is set to medium */
+#define MFPD(x)			MFP(x) | MFP_DRIVE(MEDIUM)
+
+/* GPIOs */
+#define	GPIOAF(x)		(if (x <= 15) ? 5 :	\
+				 if (x == 16) ? 0 :	\
+				 if (x == 17) ? 5 :	\
+				 if (x == 18) ? 0 :	\
+				 if (x == 19) ? 5 :	\
+				 if (x == 20) ? 0 :	\
+				 if (x <= 25) ? 5 :	\
+				 if (x == 26) ? 0 :	\
+				 if (x == 33) ? 5 : 0)
+
+#define MFP_GPIO(x)		MFPD(x) | MFP_AF(GPIOAF(x))
+
+/* UART2 */
+#define MFP47_UART2_RXD		MFPD(47) | MFP_AF(6)
+#define MFP48_UART2_TXD		MFPD(48) | MFP_AF(6)
+#define MFP88_UART2_RXD		MFPD(88) | MFP_AF(2)
+#define MFP89_UART2_TXD		MFPD(89) | MFP_AF(2)
+
+/* UART3 */
+#define  GPIO8_UART3_RXD	MFPD(8) | MFP_AF(2)
+#define  GPIO9_UART3_TXD	MFPD(9) | MFP_AF(2)
+
+/* MFU */
+#define MFP86_TX_CLK		MFPD(86) | MFP_AF(5)
+#define MFP87_TX_EN		MFPD(87) | MFP_AF(5)
+#define MFP88_TX_DQ3		MFPD(88) | MFP_AF(5)
+#define MFP89_TX_DQ2		MFPD(89) | MFP_AF(5)
+#define MFP90_TX_DQ1		MFPD(90) | MFP_AF(5)
+#define MFP91_TX_DQ0		MFPD(91) | MFP_AF(5)
+#define MFP92_MII_CRS		MFPD(92) | MFP_AF(5)
+#define MFP93_MII_COL		MFPD(93) | MFP_AF(5)
+#define MFP94_RX_CLK		MFPD(94) | MFP_AF(5)
+#define MFP95_RX_ER		MFPD(95) | MFP_AF(5)
+#define MFP96_RX_DQ3		MFPD(96) | MFP_AF(5)
+#define MFP97_RX_DQ2		MFPD(97) | MFP_AF(5)
+#define MFP98_RX_DQ1		MFPD(98) | MFP_AF(5)
+#define MFP99_RX_DQ0		MFPD(99) | MFP_AF(5)
+#define MFP100_MII_MDC		MFPD(100) | MFP_AF(5)
+#define MFP101_MII_MDIO		MFPD(101) | MFP_AF(5)
+#define MFP103_RX_DV		MFPD(103) | MFP_AF(5)
+
+/* SSP2*/
+#define MFP107_SPI_NOR_RXD	MFPD(107) | MFP_AF(4)
+#define MFP108_SPI_NOR_TXD	MFPD(108) | MFP_AF(4)
+#define MFP109_SPI_NOR_SYSCLK	MFPD(109) | MFP_AF(4)
+#define MFP111_SPI_NOR_CLK	MFPD(111) | MFP_AF(4)
+
+/* DFI */
+#define MFP0_DFI_D15		MFPD(0) | MFP_AF(0)
+#define MFP1_DFI_D14		MFPD(1) | MFP_AF(0)
+#define MFP2_DFI_D13		MFPD(2) | MFP_AF(0)
+#define MFP3_DFI_D12		MFPD(3) | MFP_AF(0)
+#define MFP4_DFI_D11		MFPD(4) | MFP_AF(0)
+#define MFP5_DFI_D10		MFPD(5) | MFP_AF(0)
+#define MFP6_DFI_D9		MFPD(6) | MFP_AF(0)
+#define MFP7_DFI_D8		MFPD(7) | MFP_AF(0)
+#define MFP8_DFI_D7		MFPD(8) | MFP_AF(0)
+#define MFP9_DFI_D6		MFPD(9) | MFP_AF(0)
+#define MFP10_DFI_D5		MFPD(10) | MFP_AF(0)
+#define MFP11_DFI_D4		MFPD(11) | MFP_AF(0)
+#define MFP12_DFI_D3		MFPD(12) | MFP_AF(0)
+#define MFP13_DFI_D2		MFPD(13) | MFP_AF(0)
+#define MFP14_DFI_D1		MFPD(14) | MFP_AF(0)
+#define MFP15_DFI_D0		MFPD(15) | MFP_AF(0)
+
+#define MFP30_DFI_ADDR0		MFPD(30) | MFP_AF(0)
+#define MFP31_DFI_ADDR1		MFPD(31) | MFP_AF(0)
+#define MFP32_DFI_ADDR2		MFPD(32) | MFP_AF(0)
+#define MFP33_DFI_ADDR3		MFPD(33) | MFP_AF(0)
+
+/* NAND */
+#define MFP16_ND_nCS0		MFPD(16) | MFP_AF(1)
+#define MFP17_ND_nWE		MFPD(17) | MFP_AF(0)
+#define MFP21_ND_ALE		MFPD(21) | MFP_AF(0)
+#define MFP22_ND_CLE		MFPD(22) | MFP_AF(0)
+#define MFP24_ND_nRE		MFPD(24) | MFP_AF(0)
+#define MFP26_ND_RnB1		MFPD(26) | MFP_AF(1)
+#define MFP27_ND_RnB2		MFPD(27) | MFP_AF(1)
+
+/* Static Memory Controller */
+#define MFP18_SMC_nCS0		MFPD(18) | MFP_AF(3)
+#define MFP18_SMC_nCS1		MFPD(18) | MFP_AF(2)
+#define MFP16_SMC_nCS0		MFPD(16) | MFP_AF(2)
+#define MFP16_SMC_nCS1		MFPD(16) | MFP_AF(3)
+#define MFP19_SMC_nCS0		MFPD(19) | MFP_AF(0)
+#define MFP20_SMC_nCS1		MFPD(20) | MFP_AF(2)
+#define MFP23_SMC_nLUA		MFPD(23) | MFP_AF(0)
+#define MFP25_SMC_nLLA		MFPD(25) | MFP_AF(0)
+#define MFP27_SMC_IRQ		MFPD(27) | MFP_AF(0)
+#define MFP28_SMC_RDY		MFPD(28) | MFP_AF(0)
+#define MFP29_SMC_SCLK		MFPD(29) | MFP_AF(0)
+#define MFP34_SMC_nCS1		MFPD(34) | MFP_AF(2)
+#define MFP35_SMC_BE1		MFPD(35) | MFP_AF(2)
+#define MFP36_SMC_BE2		MFPD(36) | MFP_AF(2)
+
+/* Compact Flash */
+#define MFP19_CF_nCE1		MFPD(19) | MFP_AF(3)
+#define MFP20_CF_nCE2		MFPD(20) | MFP_AF(3)
+#define MFP23_CF_nALE		MFPD(23) | MFP_AF(3)
+#define MFP25_CF_nRESET		MFPD(25) | MFP_AF(3)
+#define MFP28_CF_RDY		MFPD(28) | MFP_AF(3)
+#define MFP29_CF_STSCH		MFPD(29) | MFP_AF(3)
+#define MFP30_CF_nREG		MFPD(30) | MFP_AF(3)
+#define MFP31_CF_nIOIS16	MFPD(31) | MFP_AF(3)
+#define MFP32_CF_nCD1		MFPD(32) | MFP_AF(3)
+#define MFP33_CF_nCD2		MFPD(33) | MFP_AF(3)
+
+/* UART1 */
+#define MFP107_UART1_TXD	MFP(107) | MFP_AF(1) | MFP_DRIVE(FAST)
+#define MFP107_UART1_RXD	MFP(107) | MFP_AF(2) | MFP_DRIVE(FAST)
+#define MFP108_UART1_RXD	MFP(108) | MFP_AF(1) | MFP_DRIVE(FAST)
+#define MFP108_UART1_TXD	MFP(108) | MFP_AF(2) | MFP_DRIVE(FAST)
+#define MFP109_UART1_CTS	MFPD(109) | MFP_AF(1)
+#define MFP109_UART1_RTS	MFPD(109) | MFP_AF(2)
+#define MFP110_UART1_RTS	MFPD(110) | MFP_AF(1)
+#define MFP110_UART1_CTS	MFPD(110) | MFP_AF(2)
+#define MFP111_UART1_RI		MFPD(111) | MFP_AF(1)
+#define MFP111_UART1_DSR	MFPD(111) | MFP_AF(2)
+#define MFP112_UART1_DTR	MFPD(111) | MFP_AF(1)
+#define MFP112_UART1_DCD	MFPD(112) | MFP_AF(2)
+
+/* MMC1 */
+#define MFP37_MMC1_DAT7		MFPD(37) | MFP_AF(1)
+#define MFP38_MMC1_DAT6		MFPD(38) | MFP_AF(1)
+#define MFP54_MMC1_DAT5		MFPD(54) | MFP_AF(1)
+#define MFP48_MMC1_DAT4		MFPD(48) | MFP_AF(1)
+#define MFP51_MMC1_DAT3		MFPD(51) | MFP_AF(1)
+#define MFP52_MMC1_DAT2		MFPD(52) | MFP_AF(1)
+#define MFP40_MMC1_DAT1		MFPD(40) | MFP_AF(1)
+#define MFP41_MMC1_DAT0		MFPD(41) | MFP_AF(1)
+#define MFP49_MMC1_CMD		MFPD(49) | MFP_AF(1)
+#define MFP43_MMC1_CLK		MFPD(43) | MFP_AF(1)
+#define MFP53_MMC1_CD		MFPD(53) | MFP_AF(1)
+#define MFP46_MMC1_WP		MFPD(46) | MFP_AF(1)
+
+/* LCD */
+#define MFP84_LCD_CS		MFPD(84) | MFP_AF(1)
+#define MFP60_LCD_DD0		MFPD(60) | MFP_AF(1)
+#define MFP61_LCD_DD1		MFPD(61) | MFP_AF(1)
+#define MFP70_LCD_DD10		MFPD(70) | MFP_AF(1)
+#define MFP71_LCD_DD11		MFPD(71) | MFP_AF(1)
+#define MFP72_LCD_DD12		MFPD(72) | MFP_AF(1)
+#define MFP73_LCD_DD13		MFPD(73) | MFP_AF(1)
+#define MFP74_LCD_DD14		MFPD(74) | MFP_AF(1)
+#define MFP75_LCD_DD15		MFPD(75) | MFP_AF(1)
+#define MFP76_LCD_DD16		MFPD(76) | MFP_AF(1)
+#define MFP77_LCD_DD17		MFPD(77) | MFP_AF(1)
+#define MFP78_LCD_DD18		MFPD(78) | MFP_AF(1)
+#define MFP79_LCD_DD19		MFPD(79) | MFP_AF(1)
+#define MFP62_LCD_DD2		MFPD(62) | MFP_AF(1)
+#define MFP80_LCD_DD20		MFPD(80) | MFP_AF(1)
+#define MFP81_LCD_DD21		MFPD(81) | MFP_AF(1)
+#define MFP82_LCD_DD22		MFPD(82) | MFP_AF(1)
+#define MFP83_LCD_DD23		MFPD(83) | MFP_AF(1)
+#define MFP63_LCD_DD3		MFPD(63) | MFP_AF(1)
+#define MFP64_LCD_DD4		MFPD(64) | MFP_AF(1)
+#define MFP65_LCD_DD5		MFPD(65) | MFP_AF(1)
+#define MFP66_LCD_DD6		MFPD(66) | MFP_AF(1)
+#define MFP67_LCD_DD7		MFPD(67) | MFP_AF(1)
+#define MFP68_LCD_DD8		MFPD(68) | MFP_AF(1)
+#define MFP69_LCD_DD9		MFPD(69) | MFP_AF(1)
+#define MFP59_LCD_DENA_BIAS	MFPD(59) | MFP_AF(1)
+#define MFP56_LCD_FCLK_RD	MFPD(56) | MFP_AF(1)
+#define MFP57_LCD_LCLK_A0	MFPD(57) | MFP_AF(1)
+#define MFP58_LCD_PCLK_WR	MFPD(58) | MFP_AF(1)
+#define MFP85_LCD_VSYNC		MFPD(85) | MFP_AF(1)
+
+/* I2C */
+#define MFP105_CI2C_SDA		MFPD(105) | MFP_AF(1)
+#define MFP106_CI2C_SCL		MFPD(106) | MFP_AF(1)
+
+/* I2S */
+#define MFP113_I2S_MCLK		MFPD(113), MFP_AF(6)
+#define MFP114_I2S_FRM		MFPD(114), MFP_AF(1)
+#define MFP115_I2S_BCLK		MFPD(115), MFP_AF(1)
+#define MFP116_I2S_RXD		MFPD(116), MFP_AF(2)
+#define MFP117_I2S_TXD		MFPD(117), MFP_AF(2)
+
+#define MFP_PIN_MAX	117
+
+#endif /* __ARMADA100_MFP_H */
Signature · 1 line
1.7.2.1
#7 lore raw

PATCH 5/5 Armada100: Add Board Support for Marvell Aspenite-DB

From: Prafulla WADASKAR <[email protected]>

Aspenite is a Development Board for ASPEN/ARMADA168 (88AP168) Processor upto 1.2GHz with
* Parallel 1Gb x8 DDR2-1066 MHz
* 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
* Footprints for eMMC/eSD NAND & MMC x8 card
* 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
* SEAF memory board, subset of PISMO2
With Peripherals:
* 4.3? WVGA 24-bit LCD
* Audio codecs (AC97 & I2S), TSI
* VGA camera
* Video in via 3 RCA jacks, and HDMI type C out
* Marvell 88W8688 802.11bg/BT module
* GPS RF IC
* Dual analog mics & speakers, headset jack, LED, ambient light sensor
* USB2.0 HS host (A), OTG (micro AB)
* FE PHY, PCIE Mini Card slot
* GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR

This patch adds basic board support with DRAM and UART functionality The patch is tested for boot from DRAM using XDB

---
 MAINTAINERS                       |    1 +
 MAKEALL                           |    1 +
 board/Marvell/aspenite/Makefile   |   52 ++++++++++++++
 board/Marvell/aspenite/aspenite.c |   53 +++++++++++++++
 board/Marvell/aspenite/config.mk  |   26 +++++++
 boards.cfg                        |    1 +
 include/configs/aspenite.h        |  133 +++++++++++++++++++++++++++++++++++++
 7 files changed, 267 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/aspenite/Makefile
 create mode 100644 board/Marvell/aspenite/aspenite.c
 create mode 100644 board/Marvell/aspenite/config.mk
 create mode 100644 include/configs/aspenite.h
MAINTAINERS +1 -0
index 2f61776..ea4121b 100644
@@ -831,6 +831,7 @@ Matt Waddel <[email protected]>
 
 Prafulla Wadaskar <[email protected]>
 
+	aspenite	ARM926EJS (ARMADA100 88AP168 SoC)
 	mv88f6281gtw_ge	ARM926EJS (Kirkwood SoC)
 	rd6281a		ARM926EJS (Kirkwood SoC)
 	sheevaplug	ARM926EJS (Kirkwood SoC)
MAKEALL +1 -0
index 51312dd..345aa3a 100755
@@ -320,6 +320,7 @@ LIST_ARM9="			\
 	ap926ejs		\
 	ap946es			\
 	ap966			\
+	aspenite		\
 	cp920t			\
 	cp922_XA10		\
 	cp926ejs		\
board/Marvell/aspenite/Makefile new file +52 -0

52 lines not on this page · raw message

board/Marvell/aspenite/aspenite.c new file +53 -0

53 lines not on this page · raw message

board/Marvell/aspenite/config.mk new file +26 -0
new file mode 100644
index 0000000..8c91984
@@ -0,0 +1,26 @@
+#
+# (C) Copyright 2010
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <[email protected]>
+# Contributor: Mahavir Jain <[email protected]>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+CONFIG_SYS_TEXT_BASE = 0x0600000
boards.cfg +1 -0
index 0f3292f..82bdd19 100644
@@ -373,6 +373,7 @@ davinci_sffsdr	arm	arm926ejs	sffsdr		davinci		davinci
 davinci_sonata	arm	arm926ejs	sonata		davinci		davinci
 da830evm	arm	arm926ejs	da8xxevm	davinci		davinci
 da850evm	arm	arm926ejs	da8xxevm	davinci		davinci
+aspenite	arm	arm926ejs	-		Marvell		armada100
 guruplug	arm	arm926ejs	-		Marvell		kirkwood
 mv88f6281gtw_ge	arm	arm926ejs	-		Marvell		kirkwood
 openrd_base	arm	arm926ejs	-		Marvell		kirkwood
include/configs/aspenite.h new file +133 -0

133 lines not on this page · raw message

Signature · 1 line
1.7.2.1
#8 lore raw

PATCH 5/5 Armada100: Add Board Support for Marvell Aspenite-DB

Dear Prafulla Wadaskar,

In message <[email protected]> you wrote:
...

Quoted 5 lines
---
 MAINTAINERS                       |    1 +
 MAKEALL                           |    1 +
 board/Marvell/aspenite/Makefile   |   52 ++++++++++++++
 board/Marvell/aspenite/aspenite.c |   53 +++++++++++++++
Quoted 8 lines
 board/Marvell/aspenite/config.mk  |   26 +++++++
 boards.cfg                        |    1 +
 include/configs/aspenite.h        |  133 +++++++++++++++++++++++++++++++++++++
 7 files changed, 267 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/aspenite/Makefile
 create mode 100644 board/Marvell/aspenite/aspenite.c
 create mode 100644 board/Marvell/aspenite/config.mk
 create mode 100644 include/configs/aspenite.h

Please don't create a config.mk file any more (move CONFIG_SYS_TEXT_BASE setting to board config file), and please also do not create an entry to MAKEALL (gets auto-generated from boards.cfg).

Thanks.

Best regards,

Wolfgang Denk

Signature · 7 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
Is not that the nature of men and women -- that the  pleasure  is  in
the learning of each other?
	-- Natira, the High Priestess of Yonada, "For the World is
	   Hollow and I Have Touched the Sky", stardate 5476.3.
#9 lore raw

PATCH 5/5 Armada100: Add Board Support for Marvell Aspenite-DB

Quoted 31 lines

-----Original Message-----
From: Wolfgang Denk [mailto:wd at denx.de]
Sent: Wednesday, October 27, 2010 11:59 PM
To: Prafulla Wadaskar
Cc: u-boot at lists.denx.de; Manas Saksena; Lei Wen; Yu Tang; Eric Miao; Ashish Karkare; Kiran Vedere; Prabhanjan Sarnaik
Subject: Re: [U-Boot] [PATCH 5/5] Armada100: Add Board Support for Marvell Aspenite-DB

Dear Prafulla Wadaskar,

In message <[email protected]> you wrote:
...

Quoted 8 lines
---
 MAINTAINERS                       |    1 +
 MAKEALL                           |    1 +
 board/Marvell/aspenite/Makefile   |   52 ++++++++++++++
 board/Marvell/aspenite/aspenite.c |   53 +++++++++++++++
 board/Marvell/aspenite/config.mk  |   26 +++++++
 boards.cfg                        |    1 +
 include/configs/aspenite.h        |  133

+++++++++++++++++++++++++++++++++++++

Quoted 5 lines
 7 files changed, 267 insertions(+), 0 deletions(-)
 create mode 100644 board/Marvell/aspenite/Makefile
 create mode 100644 board/Marvell/aspenite/aspenite.c
 create mode 100644 board/Marvell/aspenite/config.mk
 create mode 100644 include/configs/aspenite.h
Quoted 4 lines

Please don't create a config.mk file any more (move CONFIG_SYS_TEXT_BASE setting to board config file), and please also do not create an entry to MAKEALL (gets auto-generated from boards.cfg).

Hi Wolfgang

Entry in boards.cfg already done, I am sorry for config.mk, I will change it.

Thanks
Regards...
Prafulla . .

#10 lore raw

PATCH 4/5 add Multi Fnction Pin configuration support for ARMADA100

In reply to Prafulla Wadaskar

Dear Prafulla Wadaskar,

Quoted 4 lines · In message <[email protected]> you wrote:

This patch adds the support MFP support for Marvell ARMADA100 SoCs

---

There is a typo in the Subject: please s/Fnction/Function/

[No need to repost beause of this; this can be fixed when the patch gets comitted.]

Best regards,

Wolfgang Denk

Signature · 6 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
My challenge to the goto-less programmer  is  to  recode  tcp_input()
without any gotos ... without any loss of efficiency (there has to be
a catch).                                             - W. R. Stevens