OMAP: DSS2: Add new display panel
cover OMAP: DSS2: Add new display panel
Hi,
Next patches adds support for the two new LCD panel display used on IGEP boards.
Powertip PH480272T LCD 4.3inch (480x242) display Seiko 70WVW1TZ3 LCD 7.0inch WVGA (800x480) display
Please, consider adding in next merge window.
Cheers,
Enric Balletbo i Serra (2):
OMAP: DSS2: Add Powertip PH480272T display panel
OMAP: DSS2: Add Seiko 70WVW1TZ3 display panel
drivers/video/omap2/displays/Kconfig | 14 ++ drivers/video/omap2/displays/Makefile | 2 + .../omap2/displays/panel-powertip-ph480272t.c | 155 +++++++++++++++++++ .../video/omap2/displays/panel-seiko-70wvw1tz3.c | 157 ++++++++++++++++++++ 4 files changed, 328 insertions(+), 0 deletions(-) create mode 100644 drivers/video/omap2/displays/panel-powertip-ph480272t.c create mode 100644 drivers/video/omap2/displays/panel-seiko-70wvw1tz3.c
PATCH 1/2 OMAP: DSS2: Add Powertip PH480272T display panel
From: Enric Balletbo i Serra <[email protected]>
Add new Powertip PH480242T panel, a LCD 4.3inch (480x242) display type with 24-bit RGB interface.
--- drivers/video/omap2/displays/Kconfig | 7 + drivers/video/omap2/displays/Makefile | 1 + .../omap2/displays/panel-powertip-ph480272t.c | 155 ++++++++++++++++++++ 3 files changed, 163 insertions(+), 0 deletions(-) create mode 100644 drivers/video/omap2/displays/panel-powertip-ph480272t.c
drivers/video/omap2/displays/Kconfig +7 -0
@@ -44,4 +44,11 @@ config PANEL_ACX565AKM select BACKLIGHT_CLASS_DEVICE help This is the LCD panel used on Nokia N900 + +config PANEL_POWERTIP_PH480272T + tristate "Powertip PH480272T LCD Panel" + depends on OMAP2_DSS + select BACKLIGHT_CLASS_DEVICE + help + LCD Panel used in IGEP boards. endmenu
drivers/video/omap2/displays/Makefile +1 -0
@@ -6,3 +6,4 @@ obj-$(CONFIG_PANEL_TAAL) += panel-taal.o obj-$(CONFIG_PANEL_TOPPOLY_TDO35S) += panel-toppoly-tdo35s.o obj-$(CONFIG_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_PANEL_ACX565AKM) += panel-acx565akm.o +obj-$(CONFIG_PANEL_POWERTIP_PH480272T) += panel-powertip-ph480272t.o
drivers/video/omap2/displays/panel-powertip-ph480272t.c new file +155 -0
155 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH 2/2 OMAP: DSS2: Add Seiko 70WVW1TZ3 display panel
In reply to Enric Balletbo i SerraFrom: Enric Balletbo i Serra <[email protected]>
Add new Seiko 70WVW1TZ3, a LCD 7.0inch WVGA (800x480) display type with 24-bit RGB interface and Touch-Panel
--- drivers/video/omap2/displays/Kconfig | 7 + drivers/video/omap2/displays/Makefile | 1 + .../video/omap2/displays/panel-seiko-70wvw1tz3.c | 157 ++++++++++++++++++++ 3 files changed, 165 insertions(+), 0 deletions(-) create mode 100644 drivers/video/omap2/displays/panel-seiko-70wvw1tz3.c
drivers/video/omap2/displays/Kconfig +7 -0
@@ -51,4 +51,11 @@ config PANEL_POWERTIP_PH480272T select BACKLIGHT_CLASS_DEVICE help LCD Panel used in IGEP boards. + +config PANEL_SEIKO_70WVW1TZ3 + tristate "Seiko 70WVW1TZ3 LCD Panel" + depends on OMAP2_DSS + select BACKLIGHT_CLASS_DEVICE + help + 7.0 inch LCD Panel used in IGEP boards. endmenu
drivers/video/omap2/displays/Makefile +1 -0
@@ -7,3 +7,4 @@ obj-$(CONFIG_PANEL_TOPPOLY_TDO35S) += panel-toppoly-tdo35s.o obj-$(CONFIG_PANEL_TPO_TD043MTEA1) += panel-tpo-td043mtea1.o obj-$(CONFIG_PANEL_ACX565AKM) += panel-acx565akm.o obj-$(CONFIG_PANEL_POWERTIP_PH480272T) += panel-powertip-ph480272t.o +obj-$(CONFIG_PANEL_SEIKO_70WVW1TZ3) += panel-seiko-70wvw1tz3.o
drivers/video/omap2/displays/panel-seiko-70wvw1tz3.c new file +157 -0
157 lines not on this page · raw message
Signature · 1 line
1.7.0.4
cover OMAP: DSS2: Add new display panel
In reply to Enric Balletbo i SerraHi,
Quoted 8 lines · ext Enric Balletbo i Serra
Hi,
Next patches adds support for the two new LCD panel display used on IGEP boards.
Powertip PH480272T LCD 4.3inch (480x242) display Seiko 70WVW1TZ3 LCD 7.0inch WVGA (800x480) display
Quoted 7 lines
Please, consider adding in next merge window.
Cheers,
Enric Balletbo i Serra (2):
OMAP: DSS2: Add Powertip PH480272T display panel
OMAP: DSS2: Add Seiko 70WVW1TZ3 display panel
These both are "dummy" panels, and the driver is basically a copy of the existing drivers. I don't think I will merge any more of these, sorry.
What we need is a common driver for all these dummy panels, and the driver would contain configurations for all the supported panels. The board file would pass the name of the panel used in that board to the driver, and the driver would use the configurations for that panel.
This has been discussed a few times in l-o list, but I haven't found time to implement it and nobody else has done it either.
Tomi
cover OMAP: DSS2: Add new display panel
Quoted 19 lines · Tomi Valkeinen
Hi,
Quoted 8 lines · ext Enric Balletbo i Serra
Hi,
Next patches adds support for the two new LCD panel display used on IGEP boards.
?Powertip PH480272T LCD 4.3inch (480x242) display ?Seiko 70WVW1TZ3 LCD 7.0inch WVGA (800x480) display
Quoted 7 lines
Please, consider adding in next merge window.
Cheers,
Enric Balletbo i Serra (2):
? OMAP: DSS2: Add Powertip PH480272T display panel ? OMAP: DSS2: Add Seiko 70WVW1TZ3 display panel
Quoted 8 lines
These both are "dummy" panels, and the driver is basically a copy of the existing drivers. I don't think I will merge any more of these, sorry.
What we need is a common driver for all these dummy panels, and the driver would contain configurations for all the supported panels. The board file would pass the name of the panel used in that board to the driver, and the driver would use the configurations for that panel.
It looks like that we just need one file name displays.c to do those generic things and pass the configuration from board files to this driver, such as timing or other things.
Quoted 3 lines
This has been discussed a few times in l-o list, but I haven't found time to implement it and nobody else has done it either.
I'm quite happy to do this, thanks,
Signature · 5 lines
Bryan Wu <[email protected]> Kernel Developer ? ?+86.138-1617-6545 Mobile Ubuntu Kernel Team Canonical Ltd. ? ? ?www.canonical.com Ubuntu - Linux for human beings | www.ubuntu.com
cover OMAP: DSS2: Add new display panel
Quoted 9 lines · ext Bryan Wu
Quoted 5 lines · Tomi Valkeinen
What we need is a common driver for all these dummy panels, and the driver would contain configurations for all the supported panels. The board file would pass the name of the panel used in that board to the driver, and the driver would use the configurations for that panel.
Quoted 3 lines
It looks like that we just need one file name
displays.cto do those generic things and pass the configuration from board files to this driver, such as timing or other things.
Not quite. If you pass timing information from the board files then every board file has to define all the timings, even if they are using the same panel.
That's why the configs should be in the panel driver, and the board file only has to define which panel is actually connected.
Quoted 5 lines
Quoted 3 lines
This has been discussed a few times in l-o list, but I haven't found time to implement it and nobody else has done it either.
I'm quite happy to do this, thanks,
Thanks, I appreciate that.
Tomi