Skip to contentSkip to conversation

Add SMDK5250 board support

PATCH Superseded Chander Kashyap 2 participants 7 messages Feb 3, 2012 – Feb 6, 2012

Subsystems (3)

v8 of 9 Superseded Latest is v9 →

lore
Share & tools
lore
#0 lore raw

v8 cover Add SMDK5250 board support

This patchset add support for Samsung's SMDK5250 board based on EXYNOS5250 based SoC. It also adds support for MMC SPL booting.

The porting is done by Samsung engineers at HQ in System LSI Team. I am contributing in upstreaming the code for the board.

Based upon discussions following patches are dropped in this version:
Exynos: Add CONFIG_EXYNOS4 Macro to EXYNOS4 based boards
Exynos: Clock.c: Replace exynos4 prefix with exynos

SMDK5250: enable device tree support is squashed with
EXYNOS: Add SMDK5250 board support

Chander Kashyap (4):
Exynos: Clock.c: Use CONFIG_SYS_CLK_FREQ macro
ARM: EXYNOS: Add support for Exynos5 based SoCs
EXYNOS: Add SMDK5250 board support
EXYNOS: SMDK5250: Add MMC SPL support

 MAINTAINERS                              |    1 +
 arch/arm/cpu/armv7/exynos/clock.c        |  214 +++++++++++++-
 arch/arm/include/asm/arch-exynos/clock.h |  326 +++++++++++++++++++++
 arch/arm/include/asm/arch-exynos/cpu.h   |   35 +++-
 arch/arm/include/asm/arch-exynos/dmc.h   |  146 ++++++++++
 arch/arm/include/asm/arch-exynos/gpio.h  |   99 ++++++-
 arch/arm/include/asm/arch-exynos/tzpc.h  |   52 ++++
 board/samsung/smdk5250/Makefile          |   58 ++++
 board/samsung/smdk5250/clock_init.c      |  202 +++++++++++++
 board/samsung/smdk5250/dmc_init.c        |  462 ++++++++++++++++++++++++++++++
 board/samsung/smdk5250/lowlevel_init.S   |   96 ++++++
 board/samsung/smdk5250/mmc_boot.c        |   58 ++++
 board/samsung/smdk5250/setup.h           |  451 +++++++++++++++++++++++++++++
 board/samsung/smdk5250/smdk5250.c        |  146 ++++++++++
 board/samsung/smdk5250/tzpc_init.c       |   48 +++
 boards.cfg                               |    1 +
 include/configs/s5pc210_universal.h      |    1 +
 include/configs/smdk5250.h               |  197 +++++++++++++
 include/configs/trats.h                  |    1 +
 tools/Makefile                           |    6 +
 tools/mksmdk5250spl.c                    |  119 ++++++++
 21 files changed, 2702 insertions(+), 17 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-exynos/dmc.h
 create mode 100644 arch/arm/include/asm/arch-exynos/tzpc.h
 create mode 100644 board/samsung/smdk5250/Makefile
 create mode 100644 board/samsung/smdk5250/clock_init.c
 create mode 100644 board/samsung/smdk5250/dmc_init.c
 create mode 100644 board/samsung/smdk5250/lowlevel_init.S
 create mode 100644 board/samsung/smdk5250/mmc_boot.c
 create mode 100644 board/samsung/smdk5250/setup.h
 create mode 100644 board/samsung/smdk5250/smdk5250.c
 create mode 100644 board/samsung/smdk5250/tzpc_init.c
 create mode 100644 include/configs/smdk5250.h
 create mode 100644 tools/mksmdk5250spl.c
Signature · 1 line
1.7.5.4
#1 lore raw

PATCH v8 1/4 Exynos: Clock.c: Use CONFIG_SYS_CLK_FREQ macro

CONFIG_SYS_CLK_FREQ_C210 macro giving notion of S5PC2XX (Exynos4) architecture. Replace CONFIG_SYS_CLK_FREQ_C210 with CONFIG_SYS_CLK_FREQ to make it generic for exynos architecture.

---
Changes for v2:
- None
Changes for v3:
- None
Changes for V4:
- Added CONFIG_SYS_CLK_FREQ to trats.h
Changes for v5:
- None
Changes for v6:
- None
Changes for v7:
- None
Changes for v8:
- None

 arch/arm/cpu/armv7/exynos/clock.c   |    6 +-----
 include/configs/s5pc210_universal.h |    1 +
 include/configs/trats.h             |    1 +
 3 files changed, 3 insertions(+), 5 deletions(-)
arch/arm/cpu/armv7/exynos/clock.c +1 -5
index 0c199cd..4d92c53 100644
@@ -26,10 +26,6 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/clk.h>
 
-#ifndef CONFIG_SYS_CLK_FREQ_C210
-#define CONFIG_SYS_CLK_FREQ_C210	24000000
-#endif
-
 /* exynos4: return pll clock frequency */
 static unsigned long exynos4_get_pll_clk(int pllreg)
 {
@@ -76,7 +72,7 @@ static unsigned long exynos4_get_pll_clk(int pllreg)
 	/* SDIV [2:0] */
 	s = r & 0x7;
 
-	freq = CONFIG_SYS_CLK_FREQ_C210;
+	freq = CONFIG_SYS_CLK_FREQ;
 
 	if (pllreg == EPLL) {
 		k = k & 0xffff;
include/configs/s5pc210_universal.h +1 -0
index be000cb..8286680 100644
@@ -49,6 +49,7 @@
 
 /* input clock of PLL: Universal has 24MHz input clock at EXYNOS4210 */
 #define CONFIG_SYS_CLK_FREQ_C210	24000000
+#define CONFIG_SYS_CLK_FREQ		CONFIG_SYS_CLK_FREQ_C210
 
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_CMDLINE_TAG
include/configs/trats.h +1 -0
index acb3241..10f11d9 100644
@@ -49,6 +49,7 @@
 
 /* input clock of PLL: TRATS has 24MHz input clock at EXYNOS4210 */
 #define CONFIG_SYS_CLK_FREQ_C210	24000000
+#define CONFIG_SYS_CLK_FREQ		CONFIG_SYS_CLK_FREQ_C210
 
 #define CONFIG_SETUP_MEMORY_TAGS
 #define CONFIG_CMDLINE_TAG
Signature · 1 line
1.7.5.4
#2 lore raw

PATCH v8 2/4 ARM: EXYNOS: Add support for Exynos5 based SoCs

In reply to Chander Kashyap

Samsung's ARM Cortex-A15 based SoCs are known as Exynos5 series of SoCs. This patch adds the support for Exynos5.

---
Changes for v2:
- This patch was part of "EXYNOS: Add SMDK5250 board support"
- Now it is seprated as SoC support.
Changes for v3:
- Populated complete exynos5 gpio structures
Changes for v4:
- Added dmc.h and tzpc.h header files
- Renamed EXYNOS5_PHY*_CTRL_BASE to EXYNOS5_DMC_PHY*_BASE
Changes for v5:
- None
Changes for v6:
- None
Changes for v7:
- None
Changes for v8:
- None

 arch/arm/cpu/armv7/exynos/clock.c        |  208 +++++++++++++++++++-
 arch/arm/include/asm/arch-exynos/clock.h |  326 ++++++++++++++++++++++++++++++
 arch/arm/include/asm/arch-exynos/cpu.h   |   35 +++-
 arch/arm/include/asm/arch-exynos/dmc.h   |  146 +++++++++++++
 arch/arm/include/asm/arch-exynos/gpio.h  |   99 +++++++++-
 arch/arm/include/asm/arch-exynos/tzpc.h  |   52 +++++
 6 files changed, 854 insertions(+), 12 deletions(-)
 create mode 100644 arch/arm/include/asm/arch-exynos/dmc.h
 create mode 100644 arch/arm/include/asm/arch-exynos/tzpc.h
arch/arm/cpu/armv7/exynos/clock.c +203 -5
index 4d92c53..2f7048b 100644
@@ -92,6 +92,72 @@ static unsigned long exynos4_get_pll_clk(int pllreg)
 	return fout;
 }
 
+/* exynos5: return pll clock frequency */
+static unsigned long exynos5_get_pll_clk(int pllreg)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	unsigned long r, m, p, s, k = 0, mask, fout;
+	unsigned int freq;
+
+	switch (pllreg) {
+	case APLL:
+		r = readl(&clk->apll_con0);
+		break;
+	case MPLL:
+		r = readl(&clk->mpll_con0);
+		break;
+	case EPLL:
+		r = readl(&clk->epll_con0);
+		k = readl(&clk->epll_con1);
+		break;
+	case VPLL:
+		r = readl(&clk->vpll_con0);
+		k = readl(&clk->vpll_con1);
+		break;
+	default:
+		printf("Unsupported PLL (%d)\n", pllreg);
+		return 0;
+	}
+
+	/*
+	 * APLL_CON: MIDV [25:16]
+	 * MPLL_CON: MIDV [25:16]
+	 * EPLL_CON: MIDV [24:16]
+	 * VPLL_CON: MIDV [24:16]
+	 */
+	if (pllreg == APLL || pllreg == MPLL)
+		mask = 0x3ff;
+	else
+		mask = 0x1ff;
+
+	m = (r >> 16) & mask;
+
+	/* PDIV [13:8] */
+	p = (r >> 8) & 0x3f;
+	/* SDIV [2:0] */
+	s = r & 0x7;
+
+	freq = CONFIG_SYS_CLK_FREQ;
+
+	if (pllreg == EPLL) {
+		k = k & 0xffff;
+		/* FOUT = (MDIV + K / 65536) * FIN / (PDIV * 2^SDIV) */
+		fout = (m + k / 65536) * (freq / (p * (1 << s)));
+	} else if (pllreg == VPLL) {
+		k = k & 0xfff;
+		/* FOUT = (MDIV + K / 1024) * FIN / (PDIV * 2^SDIV) */
+		fout = (m + k / 1024) * (freq / (p * (1 << s)));
+	} else {
+		if (s < 1)
+			s = 1;
+		/* FOUT = MDIV * FIN / (PDIV * 2^(SDIV - 1)) */
+		fout = m * (freq / (p * (1 << (s - 1))));
+	}
+
+	return fout;
+}
+
 /* exynos4: return ARM clock frequency */
 static unsigned long exynos4_get_arm_clk(void)
 {
@@ -114,6 +180,28 @@ static unsigned long exynos4_get_arm_clk(void)
 	return armclk;
 }
 
+/* exynos5: return ARM clock frequency */
+static unsigned long exynos5_get_arm_clk(void)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	unsigned long div;
+	unsigned long armclk;
+	unsigned int arm_ratio;
+	unsigned int arm2_ratio;
+
+	div = readl(&clk->div_cpu0);
+
+	/* ARM_RATIO: [2:0], ARM2_RATIO: [30:28] */
+	arm_ratio = (div >> 0) & 0x7;
+	arm2_ratio = (div >> 28) & 0x7;
+
+	armclk = get_pll_clk(APLL) / (arm_ratio + 1);
+	armclk /= (arm2_ratio + 1);
+
+	return armclk;
+}
+
 /* exynos4: return pwm clock frequency */
 static unsigned long exynos4_get_pwm_clk(void)
 {
@@ -157,6 +245,27 @@ static unsigned long exynos4_get_pwm_clk(void)
 	return pclk;
 }
 
+/* exynos5: return pwm clock frequency */
+static unsigned long exynos5_get_pwm_clk(void)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	unsigned long pclk, sclk;
+	unsigned int ratio;
+
+	/*
+	 * CLK_DIV_PERIC3
+	 * PWM_RATIO [3:0]
+	 */
+	ratio = readl(&clk->div_peric3);
+	ratio = ratio & 0xf;
+	sclk = get_pll_clk(MPLL);
+
+	pclk = sclk / (ratio + 1);
+
+	return pclk;
+}
+
 /* exynos4: return uart clock frequency */
 static unsigned long exynos4_get_uart_clk(int dev_index)
 {
@@ -204,6 +313,53 @@ static unsigned long exynos4_get_uart_clk(int dev_index)
 	return uclk;
 }
 
+/* exynos5: return uart clock frequency */
+static unsigned long exynos5_get_uart_clk(int dev_index)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	unsigned long uclk, sclk;
+	unsigned int sel;
+	unsigned int ratio;
+
+	/*
+	 * CLK_SRC_PERIC0
+	 * UART0_SEL [3:0]
+	 * UART1_SEL [7:4]
+	 * UART2_SEL [8:11]
+	 * UART3_SEL [12:15]
+	 * UART4_SEL [16:19]
+	 * UART5_SEL [23:20]
+	 */
+	sel = readl(&clk->src_peric0);
+	sel = (sel >> (dev_index << 2)) & 0xf;
+
+	if (sel == 0x6)
+		sclk = get_pll_clk(MPLL);
+	else if (sel == 0x7)
+		sclk = get_pll_clk(EPLL);
+	else if (sel == 0x8)
+		sclk = get_pll_clk(VPLL);
+	else
+		return 0;
+
+	/*
+	 * CLK_DIV_PERIC0
+	 * UART0_RATIO [3:0]
+	 * UART1_RATIO [7:4]
+	 * UART2_RATIO [8:11]
+	 * UART3_RATIO [12:15]
+	 * UART4_RATIO [16:19]
+	 * UART5_RATIO [23:20]
+	 */
+	ratio = readl(&clk->div_peric0);
+	ratio = (ratio >> (dev_index << 2)) & 0xf;
+
+	uclk = sclk / (ratio + 1);
+
+	return uclk;
+}
+
 /* exynos4: set the mmc clock */
 static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
 {
@@ -231,27 +387,69 @@ static void exynos4_set_mmc_clk(int dev_index, unsigned int div)
 	writel(val, addr);
 }
 
+/* exynos5: set the mmc clock */
+static void exynos5_set_mmc_clk(int dev_index, unsigned int div)
+{
+	struct exynos5_clock *clk =
+		(struct exynos5_clock *)samsung_get_base_clock();
+	unsigned int addr;
+	unsigned int val;
+
+	/*
+	 * CLK_DIV_FSYS1
+	 * MMC0_PRE_RATIO [15:8], MMC1_PRE_RATIO [31:24]
+	 * CLK_DIV_FSYS2
+	 * MMC2_PRE_RATIO [15:8], MMC3_PRE_RATIO [31:24]
+	 */
+	if (dev_index < 2) {
+		addr = (unsigned int)&clk->div_fsys1;
+	} else {
+		addr = (unsigned int)&clk->div_fsys2;
+		dev_index -= 2;
+	}
+
+	val = readl(addr);
+	val &= ~(0xff << ((dev_index << 4) + 8));
+	val |= (div & 0xff) << ((dev_index << 4) + 8);
+	writel(val, addr);
+}
+
 unsigned long get_pll_clk(int pllreg)
 {
-	return exynos4_get_pll_clk(pllreg);
+	if (cpu_is_exynos5())
+		return exynos5_get_pll_clk(pllreg);
+	else
+		return exynos4_get_pll_clk(pllreg);
 }
 
 unsigned long get_arm_clk(void)
 {
-	return exynos4_get_arm_clk();
+	if (cpu_is_exynos5())
+		return exynos5_get_arm_clk();
+	else
+		return exynos4_get_arm_clk();
 }
 
 unsigned long get_pwm_clk(void)
 {
-	return exynos4_get_pwm_clk();
+	if (cpu_is_exynos5())
+		return exynos5_get_pwm_clk();
+	else
+		return exynos4_get_pwm_clk();
 }
 
 unsigned long get_uart_clk(int dev_index)
 {
-	return exynos4_get_uart_clk(dev_index);
+	if (cpu_is_exynos5())
+		return exynos5_get_uart_clk(dev_index);
+	else
+		return exynos4_get_uart_clk(dev_index);
 }
 
 void set_mmc_clk(int dev_index, unsigned int div)
 {
-	exynos4_set_mmc_clk(dev_index, div);
+	if (cpu_is_exynos5())
+		exynos5_set_mmc_clk(dev_index, div);
+	else
+		exynos4_set_mmc_clk(dev_index, div);
 }
arch/arm/include/asm/arch-exynos/clock.h +326 -0

332 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/cpu.h +34 -1
index 3496616..89f2c2e 100644
@@ -22,6 +22,8 @@
 #ifndef _EXYNOS4_CPU_H
 #define _EXYNOS4_CPU_H
 
+#define DEVICE_NOT_AVAILABLE		0
+
 #define EXYNOS4_ADDR_BASE		0x10000000
 
 /* EXYNOS4 */
@@ -46,7 +48,34 @@
 #define EXYNOS4_ADC_BASE		0x13910000
 #define EXYNOS4_PWMTIMER_BASE		0x139D0000
 #define EXYNOS4_MODEM_BASE		0x13A00000
-#define EXYNOS4_USBPHY_CONTROL          0x10020704
+#define EXYNOS4_USBPHY_CONTROL		0x10020704
+
+#define EXYNOS4_GPIO_PART4_BASE		DEVICE_NOT_AVAILABLE
+
+/* EXYNOS5 */
+#define EXYNOS5_GPIO_PART4_BASE		0x03860000
+#define EXYNOS5_PRO_ID			0x10000000
+#define EXYNOS5_CLOCK_BASE		0x10010000
+#define EXYNOS5_POWER_BASE		0x10040000
+#define EXYNOS5_SWRESET			0x10040400
+#define EXYNOS5_SYSREG_BASE		0x10050000
+#define EXYNOS5_WATCHDOG_BASE		0x101D0000
+#define EXYNOS5_DMC_PHY0_BASE		0x10C00000
+#define EXYNOS5_DMC_PHY1_BASE		0x10C10000
+#define EXYNOS5_GPIO_PART3_BASE		0x10D10000
+#define EXYNOS5_DMC_CTRL_BASE		0x10DD0000
+#define EXYNOS5_GPIO_PART1_BASE		0x11400000
+#define EXYNOS5_MMC_BASE		0x12200000
+#define EXYNOS5_SROMC_BASE		0x12250000
+#define EXYNOS5_USBOTG_BASE		0x12480000
+#define EXYNOS5_USBPHY_BASE		0x12480000
+#define EXYNOS5_UART_BASE		0x12C00000
+#define EXYNOS5_PWMTIMER_BASE		0x12DD0000
+#define EXYNOS5_GPIO_PART2_BASE		0x13400000
+#define EXYNOS5_FIMD_BASE		0x14400000
+
+#define EXYNOS5_ADC_BASE		DEVICE_NOT_AVAILABLE
+#define EXYNOS5_MODEM_BASE		DEVICE_NOT_AVAILABLE
 
 #ifndef __ASSEMBLY__
 #include <asm/io.h>
@@ -83,12 +112,15 @@ static inline int cpu_is_##type(void)			\
 }
 
 IS_SAMSUNG_TYPE(exynos4, 0xc210)
+IS_SAMSUNG_TYPE(exynos5, 0xc520)
 
 #define SAMSUNG_BASE(device, base)				\
 static inline unsigned int samsung_get_base_##device(void)	\
 {								\
 	if (cpu_is_exynos4())					\
 		return EXYNOS4_##base;				\
+	else if (cpu_is_exynos5())				\
+		return EXYNOS5_##base;				\
 	else							\
 		return 0;					\
 }
@@ -99,6 +131,7 @@ SAMSUNG_BASE(fimd, FIMD_BASE)
 SAMSUNG_BASE(gpio_part1, GPIO_PART1_BASE)
 SAMSUNG_BASE(gpio_part2, GPIO_PART2_BASE)
 SAMSUNG_BASE(gpio_part3, GPIO_PART3_BASE)
+SAMSUNG_BASE(gpio_part4, GPIO_PART4_BASE)
 SAMSUNG_BASE(pro_id, PRO_ID)
 SAMSUNG_BASE(mmc, MMC_BASE)
 SAMSUNG_BASE(modem, MODEM_BASE)
arch/arm/include/asm/arch-exynos/dmc.h new file +146 -0

146 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/gpio.h +93 -6

120 lines not on this page · raw message

arch/arm/include/asm/arch-exynos/tzpc.h new file +52 -0

52 lines not on this page · raw message

Signature · 1 line
1.7.5.4
#3 lore raw

PATCH v8 3/4 EXYNOS: Add SMDK5250 board support

In reply to Chander Kashyap

SMDK5250 board is based on Samsungs EXYNOS5250 SoC.

---
Changes for v2:
- This patch is bifurcated into borad support and SoC support
- Fixed typo: s/EEYNOS/EXYNOS
- Squashed patch "SMDK5250: enable device tree support" in this.
Changes for v3:
- None
Changes for v4:
- Converted assembly routines for clock, memory, uart and tzpc
- init to c functions
- Moved uart init to smdk5250.c
Changes for v5:
- Remove init of gpio1
- Fixed gpio configuration for uart
Changes for v6:
- Add gpio1 init in board_uart_init, which was removed in v5
Changes for v7:
- Converted magic numbers in dmc_init.c with macro defines
- Divided mem_ctrl_init() function in dmc_init.c in smaller modules.
- Removed init of all uarts except uart2 in smdk5250.c file.
- Removed values assigned for boolean defines.
- Removed back-slashes used for continuation in smdk5250.c
Changes for v8:
- cdrex config added in dmc_init.c

 MAINTAINERS                            |    1 +
 board/samsung/smdk5250/Makefile        |   51 ++++
 board/samsung/smdk5250/clock_init.c    |  202 ++++++++++++++
 board/samsung/smdk5250/dmc_init.c      |  462 ++++++++++++++++++++++++++++++++
 board/samsung/smdk5250/lowlevel_init.S |   96 +++++++
 board/samsung/smdk5250/setup.h         |  451 +++++++++++++++++++++++++++++++
 board/samsung/smdk5250/smdk5250.c      |  146 ++++++++++
 board/samsung/smdk5250/tzpc_init.c     |   48 ++++
 boards.cfg                             |    1 +
 include/configs/smdk5250.h             |  190 +++++++++++++
 10 files changed, 1648 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/smdk5250/Makefile
 create mode 100644 board/samsung/smdk5250/clock_init.c
 create mode 100644 board/samsung/smdk5250/dmc_init.c
 create mode 100644 board/samsung/smdk5250/lowlevel_init.S
 create mode 100644 board/samsung/smdk5250/setup.h
 create mode 100644 board/samsung/smdk5250/smdk5250.c
 create mode 100644 board/samsung/smdk5250/tzpc_init.c
 create mode 100644 include/configs/smdk5250.h
MAINTAINERS +1 -0
index a05ad46..f88a282 100644
@@ -713,6 +713,7 @@ Chander Kashyap <[email protected]>
 
 	origen			ARM ARMV7 (EXYNOS4210 SoC)
 	SMDKV310		ARM ARMV7 (EXYNOS4210 SoC)
+	SMDK5250		ARM ARMV7 (EXYNOS5250 SoC)
 
 Heungjun Kim <[email protected]>
 
board/samsung/smdk5250/Makefile new file +51 -0

51 lines not on this page · raw message

board/samsung/smdk5250/clock_init.c new file +202 -0

202 lines not on this page · raw message

board/samsung/smdk5250/dmc_init.c new file +462 -0

462 lines not on this page · raw message

board/samsung/smdk5250/lowlevel_init.S new file +96 -0

96 lines not on this page · raw message

board/samsung/smdk5250/setup.h new file +451 -0

451 lines not on this page · raw message

board/samsung/smdk5250/smdk5250.c new file +146 -0

146 lines not on this page · raw message

board/samsung/smdk5250/tzpc_init.c new file +48 -0

48 lines not on this page · raw message

boards.cfg +1 -0
index 251e1b5..e8ce041 100644
@@ -221,6 +221,7 @@ s5p_goni                     arm         armv7       goni                samsung
 smdkc100                     arm         armv7       smdkc100            samsung        s5pc1xx
 origen			     arm	 armv7	     origen		 samsung	exynos
 s5pc210_universal            arm         armv7       universal_c210      samsung        exynos
+smdk5250		     arm	 armv7	     smdk5250		 samsung	exynos
 smdkv310		     arm	 armv7	     smdkv310		 samsung	exynos
 trats                        arm         armv7       trats               samsung        exynos
 harmony                      arm         armv7       harmony             nvidia         tegra2
include/configs/smdk5250.h new file +190 -0

190 lines not on this page · raw message

Signature · 1 line
1.7.5.4
#4 lore raw

PATCH v8 4/4 EXYNOS: SMDK5250: Add MMC SPL support

In reply to Chander Kashyap

This patch adds support for MMC SPL booting.

---
Changes for v2:
- None
Changes for v3:
- None
Changes for v4:
- None
Changes for v5:
- None
Changes for v6:
- None
Changes for v7:
- None
Changes for v8:
- Moved $BOARD/tools/mkexynos_image.c to tools/mksmdk5250spl.c
- Incorporated Mike's review comments

 board/samsung/smdk5250/Makefile               |   16 ++++
 board/samsung/smdk5250/mmc_boot.c             |   58 ++++++++++++
 board/samsung/smdk5250/tools/mkexynos_image.c |  117 +++++++++++++++++++++++++
 include/configs/smdk5250.h                    |    7 ++
 4 files changed, 198 insertions(+), 0 deletions(-)
 create mode 100644 board/samsung/smdk5250/mmc_boot.c
 create mode 100644 tools/mksmdk5250spl.c
board/samsung/smdk5250/Makefile +7 -0
index 80e8be3..226db1f 100644
@@ -29,7 +29,14 @@ SOBJS	:= lowlevel_init.o
 COBJS	:= clock_init.o
 COBJS	+= dmc_init.o
 COBJS	+= tzpc_init.o
+
+ifndef CONFIG_SPL_BUILD
 COBJS	+= smdk5250.o
+endif
+
+ifdef CONFIG_SPL_BUILD
+COBJS	+= mmc_boot.o
+endif
 
 SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
 OBJS	:= $(addprefix $(obj),$(COBJS) $(SOBJS))
board/samsung/smdk5250/mmc_boot.c new file +58 -0

58 lines not on this page · raw message

include/configs/smdk5250.h +7 -0
index 67e4012..f54d7ac 100644
@@ -102,6 +102,10 @@
 #define CONFIG_BOOTDELAY		3
 #define CONFIG_ZERO_BOOTDELAY_CHECK
 
+/* MMC SPL */
+#define CONFIG_SPL
+#define COPY_BL2_FNPTR_ADDR	0x02020030
+
 #define CONFIG_BOOTCOMMAND	"mmc read 40007000 451 2000; bootm 40007000"
 
 /* Miscellaneous configurable options */
@@ -178,6 +182,9 @@
 #define CONFIG_BL2_OFFSET	(CONFIG_BL1_OFFSET + CONFIG_BL1_SIZE)
 #define CONFIG_ENV_OFFSET	(CONFIG_BL2_OFFSET + CONFIG_BL2_SIZE)
 
+/* U-boot copy size from boot Media to DRAM.*/
+#define BL2_START_OFFSET	(CONFIG_BL2_OFFSET/512)
+#define BL2_SIZE_BLOC_COUNT	(CONFIG_BL2_SIZE/512)
 #define CONFIG_DOS_PARTITION
 
 #define CONFIG_IRAM_STACK	0x02050000
tools/Makefile +6 -0
index 64bcc4d..2f8210a 100644
@@ -68,6 +68,7 @@ BIN_FILES-$(CONFIG_CMD_LOADS) += img2srec$(SFX)
 BIN_FILES-$(CONFIG_XWAY_SWAP_BYTES) += xway-swap-bytes$(SFX)
 BIN_FILES-y += mkenvimage$(SFX)
 BIN_FILES-y += mkimage$(SFX)
+BIN_FILES-$(CONFIG_SMDK5250) += mksmdk5250spl$(SFX)
 BIN_FILES-$(CONFIG_MX28) += mxsboot$(SFX)
 BIN_FILES-$(CONFIG_NETCONSOLE) += ncb$(SFX)
 BIN_FILES-$(CONFIG_SHA1_CHECK_UB_IMG) += ubsha1$(SFX)
@@ -94,6 +95,7 @@ NOPED_OBJ_FILES-y += imximage.o
 NOPED_OBJ_FILES-y += omapimage.o
 NOPED_OBJ_FILES-y += mkenvimage.o
 NOPED_OBJ_FILES-y += mkimage.o
+OBJ_FILES-$(CONFIG_SMDK5250) += mksmdk5250spl.o
 OBJ_FILES-$(CONFIG_MX28) += mxsboot.o
 OBJ_FILES-$(CONFIG_NETCONSOLE) += ncb.o
 NOPED_OBJ_FILES-y += os_support.o
@@ -213,6 +215,10 @@ $(obj)mkimage$(SFX):	$(obj)aisimage.o \
 	$(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^
 	$(HOSTSTRIP) $@
 
+$(obj)mksmdk5250spl$(SFX):	$(obj)mksmdk5250spl.o
+	$(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^
+	$(HOSTSTRIP) $@
+
 $(obj)mpc86x_clk$(SFX):	$(obj)mpc86x_clk.o
 	$(HOSTCC) $(HOSTCFLAGS) $(HOSTLDFLAGS) -o $@ $^
 	$(HOSTSTRIP) $@
tools/mksmdk5250spl.c new file +119 -0

119 lines not on this page · raw message

Signature · 1 line
1.7.5.4
#5 lore raw

PATCH v8 4/4 EXYNOS: SMDK5250: Add MMC SPL support

Quoted 2 lines · On Friday 03 February 2012 11:05:57 Chander Kashyap wrote:
 board/samsung/smdk5250/tools/mkexynos_image.c |  117
 create mode 100644 tools/mksmdk5250spl.c

something funky in your diffstat ... says you're creating tools/ but the diffstat shows board/.../tools/. but the diff below looks correct.

tools/mksmdk5250spl.c

Quoted 2 lines
tools/mksmdk5250spl.c new file +0 -0

you could still name it "mkexynos_image". up to you.

tools/mksmdk5250spl.c line 82

Quoted 4 lines
tools/mksmdk5250spl.c new file +4 -0
+	if (fstat(ifd, &stat)) {
+		close(ifd);
+		close(ofd);
+	}

looks like you should issue a warning + exit here
-mike
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: This is a digitally signed message part.
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20120203/6cc939af/attachment.pgp>

#6 lore raw

PATCH v8 4/4 EXYNOS: SMDK5250: Add MMC SPL support

Hi,
As there are no changes in other patches. So is it fine to only send this patch.

Quoted 19 lines · Mike Frysinger
Quoted 2 lines · On Friday 03 February 2012 11:05:57 Chander Kashyap wrote:

?board/samsung/smdk5250/tools/mkexynos_image.c | ?117 ?create mode 100644 tools/mksmdk5250spl.c

something funky in your diffstat ... says you're creating tools/ but the diffstat shows board/.../tools/. ?but the diff below looks correct.

tools/mksmdk5250spl.c

Quoted 2 lines
tools/mksmdk5250spl.c new file +0 -0

you could still name it "mkexynos_image". ?up to you.

Quoted 4 lines

+ ? ? if (fstat(ifd, &stat)) {
+ ? ? ? ? ? ? close(ifd);
+ ? ? ? ? ? ? close(ofd);
+ ? ? }

looks like you should issue a warning + exit here
-mike

Signature · 2 lines
with warm regards,
Chander Kashyap