Haswell HDMI/DP audio enable
Subsystems (2)
v5 cover Haswell HDMI/DP audio enable
This patch series enable HDMI audio on Haswell platform, not DP audio. The DP enablement will come after the DP patches are upstream.
I tested this patch on Sharkbay machine and i could hear clear sound from HDMI port.
V2 patches fixed one warning and some type errors.
V3 patches changes:
- change some registers definitions
- use macro for IBX/CPT/HSW to get registers
- remove some unused variable intended to use in TODO list.
v4 patches changes:
- remove alsa related hack patch
v5 patches changes:
- change comments stype
- split IBX/CTP registers patch into seperate one
- remove unused register definition
Here're some notes useful for you to test the patches on Sharkbay machine:
I> please make sure your branch include below three commits in Takashi's sound tree, othersiwe there's no proper Haswell ID and HDMI ID.
For the upstream tree, please refer to sound git tree
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
You can just pull for-linus branch.
The all commits above are found in 3.6-rc1.
e926f2c850c472f813f9bab486c68a3fe0b03ae41c76684d2752b3a24bb7da183cc18e5d126dbcc9bdbe34dece4942f4d8df9865dba7785bb813366a
II> No sound from HDMI/DP.
we found it's not stable in current stage, sometimes you may not heard sound from HDMI or DP port, but most of the time you can heard clear sound. After some investigation, we suspect the HDA verb didnot really make codec change,and we regard the GPU register as the right one. (see III explanation) the easy way is to use intel_audio_dump to compare related registers, and make sure the port is enabled and unmute, otherwise there's no sound. intel_audio_tools has no support on Haswell yet, i wrote patches to make that happen, if you need the patches, please feel free to let me know. Here's part of the snapshot about port enable and mute status from intel_audio_dump:
AUD_PORT_EN_HD_CFG Port_B_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_C_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_D_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_B_Amp_Mute_Status 1 AUD_PORT_EN_HD_CFG Port_C_Amp_Mute_Status 0 AUD_PORT_EN_HD_CFG Port_D_Amp_Mute_Status 1
you can see from above message, the Port C is enabled and unmute, that's what we expect.
III> HDA Codec dependency. When you found there's no sound from HDMI, please use intel_audio_dump to check Port enable/mute status in II and also check related Pipe/Transcoder/DDI port status. Sometimes the pipe and transcoder was disabled in dpms and will not work anymore, that results in the HDMI port no sound. HDA codec's three converters are somehow hardwired to audio Pipes and if you choose the pipe, that means the regarding Codec converter should be enabled too, and only one digital Pin's HDA verbs could work, that depends on whehter your Pin select the converter as input. Here's one example about the Pipe/Transcoder/DDI port(Pipe B, DDI Port C):
DDI_BUF_CTL_A 0x00000080 DDI Buffer Controler A DDI_BUF_CTL_B 0x00000000 DDI Buffer Controler B DDI_BUF_CTL_C 0x80000000 DDI Buffer Controler C DDI_BUF_CTL_D 0x00000000 DDI Buffer Controler D DDI_BUF_CTL_E 0x80000002 DDI Buffer Controler E PIPE_CONF_A 0xc0000000 PIPE Configuration A PIPE_CONF_B 0xc0000000 PIPE Configuration B PIPE_CONF_C 0x00000000 PIPE Configuration C PIPE_CONF_EDP 0x00000000 PIPE Configuration EDP PIPE_DDI_FUNC_CTL_A 0xc4034002 PIPE DDI Function Control A PIPE_DDI_FUNC_CTL_B 0xa0035000 PIPE DDI Function Control B PIPE_DDI_FUNC_CTL_C 0x00030000 PIPE DDI Function Control C PIPE_DDI_FUNC_CTL_EDP 0x00030000 PIPE DDI Function Control EDP
Wang Xingchao (3):
Wang Xingchao (4):
drm/i915: HSW audio registers definition drm/i915: write eld info for HDMI audio drm/i915: Haswell HDMI audio enable
drm/i915: use _PIPE macro for IBX/CPT register definition
drivers/gpu/drm/i915/i915_reg.h | 71 ++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_ddi.c | 6 ++- drivers/gpu/drm/i915/intel_display.c | 52 ++++++++++++++++++++----- 3 files changed, 118 insertions(+), 11 deletions(-)
Signature · 1 line
1.7.9.5
v5 cover Haswell HDMI/DP audio enable
This patch series enable HDMI audio on Haswell platform, not DP audio. The DP enablement will come after the DP patches are upstream.
I tested this patch on Sharkbay machine and i could hear clear sound from HDMI port.
V2 patches fixed one warning and some type errors.
V3 patches changes:
- change some registers definitions
- use macro for IBX/CPT/HSW to get registers
- remove some unused variable intended to use in TODO list.
v4 patches changes:
- remove alsa related hack patch
v5 patches changes:
- change comments stype
- split IBX/CTP registers patch into seperate one
- remove unused register definition
Here're some notes useful for you to test the patches on Sharkbay machine:
I> please make sure your branch include below three patches in Takashi's sound tree, othersiwe there's no proper Haswell ID and HDMI ID.
http://git.alsa-project.org/?p=alsa-kmirror.git;a=commitdiff;h=79fc901301d6115b11457e8240ed6abc4b3f5c65
http://git.alsa-project.org/?p=alsa-kmirror.git;a=commitdiff;h=e269cee227a2b2297b79bfc71094c709b9387061
http://git.alsa-project.org/?p=alsa-kmirror.git;a=commitdiff;h=cb192625233496ac3d96cce667ebf4e322dab678
II> No sound from HDMI/DP.
we found it's not stable in current stage, sometimes you may not heard sound from HDMI or DP port, but most of the time you can heard clear sound. After some investigation, we suspect the HDA verb didnot really make codec change,and we regard the GPU register as the right one. (see III explanation) the easy way is to use intel_audio_dump to compare related registers, and make sure the port is enabled and unmute, otherwise there's no sound. intel_audio_tools has no support on Haswell yet, i wrote patches to make that happen, if you need the patches, please feel free to let me know. Here's part of the snapshot about port enable and mute status from intel_audio_dump:
AUD_PORT_EN_HD_CFG Port_B_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_C_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_D_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_B_Amp_Mute_Status 1 AUD_PORT_EN_HD_CFG Port_C_Amp_Mute_Status 0 AUD_PORT_EN_HD_CFG Port_D_Amp_Mute_Status 1
you can see from above message, the Port C is enabled and unmute, that's what we expect.
III> HDA Codec dependency. When you found there's no sound from HDMI, please use intel_audio_dump to check Port enable/mute status in II and also check related Pipe/Transcoder/DDI port status. Sometimes the pipe and transcoder was disabled in dpms and will not work anymore, that results in the HDMI port no sound. HDA codec's three converters are somehow hardwired to audio Pipes and if you choose the pipe, that means the regarding Codec converter should be enabled too, and only one digital Pin's HDA verbs could work, that depends on whehter your Pin select the converter as input. Here's one example about the Pipe/Transcoder/DDI port(Pipe B, DDI Port C):
DDI_BUF_CTL_A 0x00000080 DDI Buffer Controler A DDI_BUF_CTL_B 0x00000000 DDI Buffer Controler B DDI_BUF_CTL_C 0x80000000 DDI Buffer Controler C DDI_BUF_CTL_D 0x00000000 DDI Buffer Controler D DDI_BUF_CTL_E 0x80000002 DDI Buffer Controler E PIPE_CONF_A 0xc0000000 PIPE Configuration A PIPE_CONF_B 0xc0000000 PIPE Configuration B PIPE_CONF_C 0x00000000 PIPE Configuration C PIPE_CONF_EDP 0x00000000 PIPE Configuration EDP PIPE_DDI_FUNC_CTL_A 0xc4034002 PIPE DDI Function Control A PIPE_DDI_FUNC_CTL_B 0xa0035000 PIPE DDI Function Control B PIPE_DDI_FUNC_CTL_C 0x00030000 PIPE DDI Function Control C PIPE_DDI_FUNC_CTL_EDP 0x00030000 PIPE DDI Function Control EDP
Wang Xingchao (3):
Wang Xingchao (4):
drm/i915: HSW audio registers definition drm/i915: write eld info for HDMI audio drm/i915: Haswell HDMI audio enable
drm/i915: use _PIPE macro for IBX/CPT register definition
drivers/gpu/drm/i915/i915_reg.h | 71 ++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_ddi.c | 6 ++- drivers/gpu/drm/i915/intel_display.c | 52 ++++++++++++++++++++----- 3 files changed, 118 insertions(+), 11 deletions(-)
Signature · 1 line
1.7.9.5
PATCH v5 1/4 drm/i915: HSW audio registers definition
In reply to Wang XingchaoAdd hsw audio registers definition
--- drivers/gpu/drm/i915/i915_reg.h | 47 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 47 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +47 -0
@@ -4277,6 +4277,53 @@#define AUD_CONFIG_PIXEL_CLOCK_HDMI (0xf << 16)#define AUD_CONFIG_DISABLE_NCTS (1 << 3) +/* HSW Audio */ +#define HSW_AUD_CONFIG_A 0x65000/* Audio Configuration Transcoder A */ +#define HSW_AUD_CONFIG_B 0x65100/* Audio Configuration Transcoder B */ +#define HSW_AUD_CFG (pipe) _PIPE(pipe, \ + HSW_AUD_CONFIG_A, \ + HSW_AUD_CONFIG_B) + +#define HSW_AUD_MISC_CTRL_A 0x65010/* Audio Misc Control Convert 1 */ +#define HSW_AUD_MISC_CTRL_B 0x65110/* Audio Misc Control Convert 2 */ +#define HSW_AUD_MISC_CTRL (pipe) _PIPE(pipe, \ + HSW_AUD_MISC_CTRL_A, \ + HSW_AUD_MISC_CTRL_B) + +#define HSW_AUD_DIP_ELD_CTRL_ST_A 0x650b4/* Audio DIP and ELD Control State Transcoder A */ +#define HSW_AUD_DIP_ELD_CTRL_ST_B 0x651b4/* Audio DIP and ELD Control State Transcoder B */ +#define HSW_AUD_DIP_ELD_CTRL (pipe) _PIPE(pipe, \ + HSW_AUD_DIP_ELD_CTRL_ST_A, \ + HSW_AUD_DIP_ELD_CTRL_ST_B) + +/* Audio Digital Converter */ +#define HSW_AUD_DIG_CNVT_1 0x65080/* Audio Converter 1 */ +#define HSW_AUD_DIG_CNVT_2 0x65180/* Audio Converter 1 */ +#define AUD_DIG_CNVT (pipe) _PIPE(pipe, \ + HSW_AUD_DIG_CNVT_1, \ + HSW_AUD_DIG_CNVT_2) + +#define HSW_AUD_EDID_DATA_A 0x65050 +#define HSW_AUD_EDID_DATA_B 0x65150 +#define HSW_AUD_EDID_DATA (pipe) _PIPE(pipe, \ + HSW_AUD_EDID_DATA_A, \ + HSW_AUD_EDID_DATA_B) + +#define HSW_AUD_PIPE_CONV_CFG 0x6507c/* Audio pipe and converter configs */ +#define HSW_AUD_PIN_ELD_CP_VLD 0x650c0/* Audio ELD and CP Ready Status */ +#define AUDIO_INACTIVE_C (1<<11) +#define AUDIO_INACTIVE_B (1<<7) +#define AUDIO_INACTIVE_A (1<<3) +#define AUDIO_OUTPUT_ENABLE_A (1<<2) +#define AUDIO_OUTPUT_ENABLE_B (1<<6) +#define AUDIO_OUTPUT_ENABLE_C (1<<10) +#define AUDIO_ELD_VALID_A (1<<0) +#define AUDIO_ELD_VALID_B (1<<4) +#define AUDIO_ELD_VALID_C (1<<8) +#define AUDIO_CP_READY_A (1<<1) +#define AUDIO_CP_READY_B (1<<5) +#define AUDIO_CP_READY_C (1<<9) +/* HSW Power Wells */ #define HSW_PWR_WELL_CTL1 0x45400/* BIOS */ #define HSW_PWR_WELL_CTL2 0x45404/* Driver */
Signature · 1 line
1.7.9.5
PATCH v5 2/4 drm/i915: write eld info for HDMI audio
In reply to Wang XingchaoHDMI audio related registers will be configured in write_eld callback.
--- drivers/gpu/drm/i915/intel_ddi.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/intel_ddi.c +5 -1
@@ -718,8 +718,12 @@ void intel_ddi_mode_set(struct drm_encoder *encoder,/* Proper support for digital audio needs a new logic and a new set * of registers, so we leave it for future patch bombing. */ -DRM_DEBUG_DRIVER ("HDMI audio on pipe %c not yet supported on DDI\n" , +DRM_DEBUG_DRIVER ("HDMI audio on pipe %c on DDI\n" ,pipe_name (intel_crtc->pipe)); + +/* write eld */ +DRM_DEBUG_DRIVER ("HDMI audio: write eld information\n" ); +intel_write_eld (encoder, adjusted_mode); }/* Enable PIPE_DDI_FUNC_CTL for the pipe to work in HDMI mode */
Signature · 1 line
1.7.9.5
PATCH v5 3/4 drm/i915: Haswell HDMI audio enable
In reply to Wang XingchaoInitialize Haswell HDMI audio registers to generate an unsolicited response to the audio controller driver to indicate that the controller sequence should start.
--- drivers/gpu/drm/i915/intel_display.c | 37 ++++++++++++++++++++++++++++++++++ 1 file changed, 37 insertions(+)
drivers/gpu/drm/i915/intel_display.c +37 -0
@@ -5071,6 +5071,7 @@ static void ironlake_write_eld(struct drm_connector *connector, struct drm_crtc *crtc) {struct drm_i915_private *dev_priv = connector->dev->dev_private; +struct drm_device *dev = crtc->dev;uint8_t *eld = connector->eld;uint32_t eldv;uint32_t i;
@@ -5079,12 +5080,18 @@ static void ironlake_write_eld(struct drm_connector *connector,int aud_config;int aud_cntl_st;int aud_cntrl_st2; +int pipe =to_intel_crtc (crtc)->pipe;if (HAS_PCH_IBX (connector->dev)) { hdmiw_hdmiedid =IBX_HDMIW_HDMIEDID_A ; aud_config =IBX_AUD_CONFIG_A ; aud_cntl_st =IBX_AUD_CNTL_ST_A ; aud_cntrl_st2 =IBX_AUD_CNTL_ST2 ; + }else if (IS_HASWELL (dev)) { + hdmiw_hdmiedid =HSW_AUD_EDID_DATA (pipe); + aud_cntl_st =HSW_AUD_DIP_ELD_CTRL (pipe); + aud_config =HSW_AUD_CFG (pipe); + aud_cntrl_st2 =HSW_AUD_PIN_ELD_CP_VLD ; }else { hdmiw_hdmiedid =CPT_HDMIW_HDMIEDID_A ; aud_config =CPT_AUD_CONFIG_A ;
@@ -5092,6 +5099,34 @@ static void ironlake_write_eld(struct drm_connector *connector, aud_cntrl_st2 =CPT_AUD_CNTRL_ST2 ; } +if (IS_HASWELL (dev)) { +int tmp; +int aud_vld =HSW_AUD_PIN_ELD_CP_VLD ; + +DRM_DEBUG_DRIVER ("HDMI: Haswell Audio initialize....\n" ); + +/* Audio output enable */ +DRM_DEBUG_DRIVER ("HDMI audio: enable codec\n" ); + tmp =I915_READ (aud_vld); + tmp |= (AUDIO_OUTPUT_ENABLE_A |AUDIO_OUTPUT_ENABLE_B |AUDIO_OUTPUT_ENABLE_C ); +I915_WRITE (aud_vld, tmp); + +/* Set ELD valid state */ + tmp =I915_READ (aud_vld); +DRM_DEBUG_DRIVER ("HDMI audio: pin eld vld status=0x%8x\n" , tmp); + tmp |= (AUDIO_ELD_VALID_A |AUDIO_ELD_VALID_B |AUDIO_ELD_VALID_C ); +I915_WRITE (aud_vld, tmp); + tmp =I915_READ (aud_vld); +DRM_DEBUG_DRIVER ("HDMI audio: eld vld status=0x%8x\n" , tmp); + +/* Enable HDMI mode */ + tmp =I915_READ (aud_config); +DRM_DEBUG_DRIVER ("HDMI audio: audio conf: 0x%8x\n" , tmp); +/* clear N_programing_enable and N_value_index */ + tmp &= ~(AUD_CONFIG_N_VALUE_INDEX |AUD_CONFIG_N_PROG_ENABLE ); +I915_WRITE (aud_config, tmp); + } + i =to_intel_crtc (crtc)->pipe; hdmiw_hdmiedid += i *0x100 ; aud_cntl_st += i *0x100 ;
@@ -5135,6 +5170,8 @@ static void ironlake_write_eld(struct drm_connector *connector, i =I915_READ (aud_cntl_st); i &= ~IBX_ELD_ADDRESS ;I915_WRITE (aud_cntl_st, i); + i = (i >>29 ) &0x3 ;/* DIP_Port_Select, 0x1 = PortB */ +DRM_DEBUG_DRIVER ("port num:%d\n" , i); len =min_t (uint8_t, eld[2 ],21 );/* 84 bytes of hw ELD buffer */ DRM_DEBUG_DRIVER ("ELD size %d\n" , len);
Signature · 1 line
1.7.9.5
PATCH v5 4/4 drm/i915: use _PIPE macro for IBX/CPT register definition
In reply to Wang XingchaoUse _PIPE macro to get correct register definition for IBX/CPT, discard old variable "i" way.
--- drivers/gpu/drm/i915/i915_reg.h | 24 ++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_display.c | 17 ++++++----------- 2 files changed, 30 insertions(+), 11 deletions(-)
drivers/gpu/drm/i915/i915_reg.h +24 -0
@@ -4247,7 +4247,15 @@#define G4X_HDMIW_HDMIEDID 0x6210C#define IBX_HDMIW_HDMIEDID_A 0xE2050 +#define IBX_HDMIW_HDMIEDID_B 0xE2150 +#define IBX_HDMIW_HDMIEDID (pipe) _PIPE(pipe, \ + IBX_HDMIW_HDMIEDID_A, \ + IBX_HDMIW_HDMIEDID_B)#define IBX_AUD_CNTL_ST_A 0xE20B4 +#define IBX_AUD_CNTL_ST_B 0xE21B4 +#define IBX_AUD_CNTL_ST (pipe) _PIPE(pipe, \ + IBX_AUD_CNTL_ST_A, \ + IBX_AUD_CNTL_ST_B)#define IBX_ELD_BUFFER_SIZE (0x1f << 10)#define IBX_ELD_ADDRESS (0x1f << 5)#define IBX_ELD_ACK (1 << 4)
@@ -4256,7 +4264,15 @@#define IBX_CP_READYB (1 << 1)#define CPT_HDMIW_HDMIEDID_A 0xE5050 +#define CPT_HDMIW_HDMIEDID_B 0xE5150 +#define CPT_HDMIW_HDMIEDID (pipe) _PIPE(pipe, \ + CPT_HDMIW_HDMIEDID_A, \ + CPT_HDMIW_HDMIEDID_B)#define CPT_AUD_CNTL_ST_A 0xE50B4 +#define CPT_AUD_CNTL_ST_B 0xE51B4 +#define CPT_AUD_CNTL_ST (pipe) _PIPE(pipe, \ + CPT_AUD_CNTL_ST_A, \ + CPT_AUD_CNTL_ST_B)#define CPT_AUD_CNTRL_ST2 0xE50C0/* These are the 4 32-bit write offset registers for each stream
@@ -4266,7 +4282,15 @@#define GEN7_SO_WRITE_OFFSET (n) (0x5280 + (n) * 4)#define IBX_AUD_CONFIG_A 0xe2000 +#define IBX_AUD_CONFIG_B 0xe2100 +#define IBX_AUD_CFG (pipe) _PIPE(pipe, \ + IBX_AUD_CONFIG_A, \ + IBX_AUD_CONFIG_B)#define CPT_AUD_CONFIG_A 0xe5000 +#define CPT_AUD_CONFIG_B 0xe5100 +#define CPT_AUD_CFG (pipe) _PIPE(pipe, \ + CPT_AUD_CONFIG_A, \ + CPT_AUD_CONFIG_B)#define AUD_CONFIG_N_VALUE_INDEX (1 << 29)#define AUD_CONFIG_N_PROG_ENABLE (1 << 28)#define AUD_CONFIG_UPPER_N_SHIFT 20
drivers/gpu/drm/i915/intel_display.c +6 -11
@@ -5083,9 +5083,9 @@ static void ironlake_write_eld(struct drm_connector *connector,int pipe =to_intel_crtc (crtc)->pipe;if (HAS_PCH_IBX (connector->dev)) { - hdmiw_hdmiedid =IBX_HDMIW_HDMIEDID_A ; - aud_config =IBX_AUD_CONFIG_A ; - aud_cntl_st =IBX_AUD_CNTL_ST_A ; + hdmiw_hdmiedid =IBX_HDMIW_HDMIEDID (pipe); + aud_config =IBX_AUD_CFG (pipe); + aud_cntl_st =IBX_AUD_CNTL_ST (pipe); aud_cntrl_st2 =IBX_AUD_CNTL_ST2 ; }else if (IS_HASWELL (dev)) { hdmiw_hdmiedid =HSW_AUD_EDID_DATA (pipe);
@@ -5093,9 +5093,9 @@ static void ironlake_write_eld(struct drm_connector *connector, aud_config =HSW_AUD_CFG (pipe); aud_cntrl_st2 =HSW_AUD_PIN_ELD_CP_VLD ; }else { - hdmiw_hdmiedid =CPT_HDMIW_HDMIEDID_A ; - aud_config =CPT_AUD_CONFIG_A ; - aud_cntl_st =CPT_AUD_CNTL_ST_A ; + hdmiw_hdmiedid =CPT_HDMIW_HDMIEDID (pipe); + aud_config =CPT_AUD_CFG (pipe); + aud_cntl_st =CPT_AUD_CNTL_ST (pipe); aud_cntrl_st2 =CPT_AUD_CNTRL_ST2 ; }
@@ -5127,11 +5127,6 @@ static void ironlake_write_eld(struct drm_connector *connector,I915_WRITE (aud_config, tmp); } - i =to_intel_crtc (crtc)->pipe; - hdmiw_hdmiedid += i *0x100 ; - aud_cntl_st += i *0x100 ; - aud_config += i *0x100 ; -DRM_DEBUG_DRIVER ("ELD on pipe %c\n" ,pipe_name (i)); i =I915_READ (aud_cntl_st);
Signature · 1 line
1.7.9.5
Dear Wang,
first is Wang your first name?
Am Mittwoch, den 08.08.2012, 11:03 +0800 schrieb Wang Xingchao:
Quoted 5 lines
This patch series enable HDMI audio on Haswell platform, not DP audio. The DP enablement will come after the DP patches are upstream.
I tested this patch on Sharkbay machine and i could hear clear sound from HDMI port.
Could you please add if that was a TV or a receiver?
Quoted 7 lines
V2 patches fixed one warning and some type errors.
V3 patches changes:
- change some registers definitions
- use macro for IBX/CPT/HSW to get registers
- remove some unused variable intended to use in TODO list.
Quoted 6 lines
v4 patches changes:
- remove alsa related hack patchv5 patches changes:
- change comments stype
- split IBX/CTP registers patch into seperate one
• sep*a*rate
Quoted 5 lines
- remove unused register definition
Here're some notes useful for you to test the patches on Sharkbay machine:
I> please make sure your branch include below three commits in Takashi's sound tree, othersiwe there's no proper Haswell ID and HDMI ID.
• White space at the end.
• other*wise*
Quoted 6 lines
For the upstream tree, please refer to sound git tree
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
You can just pull for-linus branch.
The all commits above are found in 3.6-rc1.
Quoted 8 lines
e926f2c850c472f813f9bab486c68a3fe0b03ae41c76684d2752b3a24bb7da183cc18e5d126dbcc9bdbe34dece4942f4d8df9865dba7785bb813366aII> No sound from HDMI/DP.
we found it's not stable in current stage, sometimes you may not heard sound from HDMI or DP port, but most of the time you can heard clear sound. After some investigation, we suspect the HDA verb didnot really make codec
did not
Quoted 17 lines
change,and we regard the GPU register as the right one. (see III explanation) the easy way is to use
intel_audio_dumpto compare related registers, and make sure the port is enabled and unmute, otherwise there's no sound.intel_audio_toolshas no support on Haswell yet, i wrote patches to make that happen, if you need the patches, please feel free to let me know. Here's part of the snapshot about port enable and mute status fromintel_audio_dump:AUD_PORT_EN_HD_CFG Port_B_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_C_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_D_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_B_Amp_Mute_Status 1 AUD_PORT_EN_HD_CFG Port_C_Amp_Mute_Status 0 AUD_PORT_EN_HD_CFG Port_D_Amp_Mute_Status 1you can see from above message, the Port C is enabled and unmute, that's what we expect.
Quoted 8 lines
III> HDA Codec dependency. When you found there's no sound from HDMI, please use
intel_audio_dumpto check Port enable/mute status in II and also check related Pipe/Transcoder/DDI port status. Sometimes the pipe and transcoder was disabled in dpms and will not work anymore, that results in the HDMI port no sound. HDA codec's three converters are somehow hardwired to audio Pipes and if you choose the pipe, that means the regarding Codec converter should be enabled too, and only one digital Pin's HDA verbs could work, that depends on whehter your Pin select the converter as input. Here's one example about the
whe*th*er
Quoted 16 lines
Pipe/Transcoder/DDI
port(Pipe B, DDI Port C):DDI_BUF_CTL_A 0x00000080 DDI Buffer Controler A DDI_BUF_CTL_B 0x00000000 DDI Buffer Controler B DDI_BUF_CTL_C 0x80000000 DDI Buffer Controler C DDI_BUF_CTL_D 0x00000000 DDI Buffer Controler D DDI_BUF_CTL_E 0x80000002 DDI Buffer Controler E PIPE_CONF_A 0xc0000000 PIPE Configuration A PIPE_CONF_B 0xc0000000 PIPE Configuration B PIPE_CONF_C 0x00000000 PIPE Configuration C PIPE_CONF_EDP 0x00000000 PIPE Configuration EDP PIPE_DDI_FUNC_CTL_A 0xc4034002 PIPE DDI Function Control A PIPE_DDI_FUNC_CTL_B 0xa0035000 PIPE DDI Function Control B PIPE_DDI_FUNC_CTL_C 0x00030000 PIPE DDI Function Control C PIPE_DDI_FUNC_CTL_EDP 0x00030000 PIPE DDI Function Control EDP
Quoted 1 line
Wang Xingchao (3):
The line above should be removed.
Quoted 10 lines
Wang Xingchao (4):
drm/i915: HSW audio registers definition drm/i915: write eld info for HDMI audio drm/i915: Haswell HDMI audio enable
drm/i915: use_PIPEmacro for IBX/CPT register definitiondrivers/gpu/drm/i915/i915_reg.h | 71 ++++++++++++++++++++++++++++++++++ drivers/gpu/drm/i915/intel_ddi.c | 6 ++- drivers/gpu/drm/i915/intel_display.c | 52 ++++++++++++++++++++----- 3 files changed, 118 insertions(+), 11 deletions(-)
Thanks,
Paul
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
Quoted 10 lines
-----Original Message-----
From: Paul Menzel [mailto:[email protected]]
Sent: Wednesday, August 08, 2012 3:15 PM
To: Wang, Xingchao
Cc: [email protected]; [email protected]; Fu, Michael; Wu, Fengguang
Subject: Re: [Intel-gfx] [PATCH v5 0/4] Haswell HDMI/DP audio enable
Quoted 5 lines
Dear Wang,
first is Wang your first name?
Yes. :)
Quoted 9 lines
Am Mittwoch, den 08.08.2012, 11:03 +0800 schrieb Wang Xingchao:
Quoted 5 lines
This patch series enable HDMI audio on Haswell platform, not DP audio. The DP enablement will come after the DP patches are upstream.
I tested this patch on Sharkbay machine and i could hear clear sound from HDMI port.
Could you please add if that was a TV or a receiver?
I tested the patch on Haswell Based Machine with a monitor hasing HDMI ports, this is the eld information from the monitor:
cat /proc/asound/card0/eld#0.*
monitor_present 0 eld_valid 0 monitor_present 1 eld_valid 1 monitor_name DELL 2408WFP connection_type HDMI eld_version [0x2] CEA-861D or below edid_version [0x3] CEA-861-B, C or D manufacture_id 0xac10 product_id 0xa02c port_id 0x0 support_hdcp 0 support_ai 1 audio_sync_delay 0 speakers [0x1] FL/FR sad_count 1 sad0_coding_type [0x1] LPCM sad0_channels 2 sad0_rates [0xe0] 32000 44100 48000 sad0_bits [0xe0000] 16 20 24 monitor_present 0 eld_valid 0
Quoted 104 lines
Quoted 7 lines
V2 patches fixed one warning and some type errors.
V3 patches changes:
- change some registers definitions
- use macro for IBX/CPT/HSW to get registers
- remove some unused variable intended to use in TODO list.Quoted 6 lines
v4 patches changes:
- remove alsa related hack patchv5 patches changes:
- change comments stype
- split IBX/CTP registers patch into seperate one• sep*a*rate
Quoted 6 lines
- remove unused register definition
Here're some notes useful for you to test the patches on Sharkbay machine:
I> please make sure your branch include below three commits in I> Takashi's
sound tree, othersiwe there's no proper Haswell ID and HDMI ID.• White space at the end.
• other*wise*Quoted 10 lines
For the upstream tree, please refer to sound git tree
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound.git
You can just pull for-linus branch.
The all commits above are found in 3.6-rc1.
e926f2c850c472f813f9bab486c68a3fe0b03ae41c76684d2752b3a24bb7da183cc18e5d126dbcc9bdbe34dece4942f4d8df9865dba7785bb813366aQuoted 5 lines
II> No sound from HDMI/DP.
we found it's not stable in current stage, sometimes you may not heard sound from HDMI or DP port, but most of the time you can heard clear sound. After some investigation, we suspect the HDA verb didnot really make codecdid not
Quoted 3 lines
change,and we regard the GPU register as the right one. (see III explanation) the easy way is to use
intel_audio_dumpto compare related registers, and make sure the port is enabled and unmute, otherwisethere's no sound.
Quoted 3 lines
intel_audio_toolshas no support on Haswell yet, i wrote patches to make that happen, if you need the patches, please feel free to let me know. Here's part of the snapshot about port enable and mute status from
intel_audio_dump:Quoted 11 lines
AUD_PORT_EN_HD_CFG Port_B_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_C_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_D_Out_Enable 1 AUD_PORT_EN_HD_CFG Port_B_Amp_Mute_Status 1 AUD_PORT_EN_HD_CFG Port_C_Amp_Mute_Status 0 AUD_PORT_EN_HD_CFG Port_D_Amp_Mute_Status 1you can see from above message, the Port C is enabled and unmute, that's what we expect.
Quoted 10 lines
III> HDA Codec dependency. When you found there's no sound from HDMI, III> please
useintel_audio_dumpto check Port enable/mute status in II and also check related Pipe/Transcoder/DDI port status. Sometimes the pipe and transcoder was disabled in dpms and will not work anymore, that results in the HDMI port no sound. HDA codec's three converters are somehow hardwired to audio Pipes and if you choose the pipe, that means the regarding Codec converter should be enabled too, and only one digital Pin's HDA verbs could work, that depends on whehter your Pin select the converter as input. Here's one example about thewhe*th*er
Quoted 16 lines
Pipe/Transcoder/DDI
port(Pipe B, DDI Port C):DDI_BUF_CTL_A 0x00000080 DDI Buffer Controler A DDI_BUF_CTL_B 0x00000000 DDI Buffer Controler B DDI_BUF_CTL_C 0x80000000 DDI Buffer Controler C DDI_BUF_CTL_D 0x00000000 DDI Buffer Controler D DDI_BUF_CTL_E 0x80000002 DDI Buffer Controler E PIPE_CONF_A 0xc0000000 PIPE Configuration A PIPE_CONF_B 0xc0000000 PIPE Configuration B PIPE_CONF_C 0x00000000 PIPE Configuration C PIPE_CONF_EDP 0x00000000 PIPE Configuration EDP PIPE_DDI_FUNC_CTL_A 0xc4034002 PIPE DDI Function Control A PIPE_DDI_FUNC_CTL_B 0xa0035000 PIPE DDI Function Control B PIPE_DDI_FUNC_CTL_C 0x00030000 PIPE DDI Function Control C PIPE_DDI_FUNC_CTL_EDP 0x00030000 PIPE DDI Function Control EDPQuoted 1 line
Wang Xingchao (3):
The line above should be removed.
Quoted 7 lines
Wang Xingchao (4):
drm/i915: HSW audio registers definition drm/i915: write eld info for HDMI audio drm/i915: Haswell HDMI audio enable
drm/i915: use_PIPEmacro for IBX/CPT register definitiondrivers/gpu/drm/i915/i915_reg.h | 71++++++++++++++++++++++++++++++++++
Quoted 8 lines
Quoted 3 lines
drivers/gpu/drm/i915/intel_ddi.c | 6 ++- drivers/gpu/drm/i915/intel_display.c | 52 ++++++++++++++++++++----- 3 files changed, 118 insertions(+), 11 deletions(-)Thanks,
Paul
Thanks your review Paul, I fixed the type error.
--xingchao
_______________________________________________
Intel-gfx mailing list
[email protected]
http://lists.freedesktop.org/mailman/listinfo/intel-gfx