J721S2: Add support for additional IPs
Subsystems (2)
v5 cover J721S2: Add support for additional IPs
The following series of patches add support for the following on J721S2 common processor board,
- USB
- SerDes
- OSPI
- PCIe
Changes from v1:
* Resolve issues with dt schema reporting
* Minor changes related to consistency on node naming and value
Changes from v2:
* Added PCIe RC + EP enablement patchsets
* Added device-id for j722s2 PCIe host in dt documentation
* Reworked SERDES + WIZ enablement patchset to use properies for clocks defines versus entire devicetree nodes. Results in cleaner code that doesn't break dt-schema or the driver functionality.
Changes from v3:
* Rebased changes on top of '[PATCH 00/12] TI J7x Disable Incomplete DT Nodes'
* Removed "dt-bindings: PCI: Add host mode device-id for j721s2 platform" patch and send it own series to avoid a dependency that would hold up other patches in this series
Changes from v4:
* Add my Signed-off-by lines to all patchsets
Aswath Govindraju (7):
arm64: dts: ti: k3-j721s2-main: Add support for USB
arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI
arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0
arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes
arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node
arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe
Matt Ranostay (1):
arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
.../dts/ti/k3-j721s2-common-proc-board.dts | 92 +++++++++++ arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 156 ++++++++++++++++++ .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 40 +++++ arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 42 +++++ 4 files changed, 330 insertions(+)
Signature · 1 line
2.38.GIT
PATCH v5 1/8 arm64: dts: ti: k3-j721s2-main: Add support for USB
From: Aswath Govindraju <[email protected]>
Add support for single instance of USB 3.0 controller in J721S2 SoC.
--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++ 1 file changed, 42 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +42 -0
@@ -26,6 +26,20 @@ l3cache-sram@200000 { }; }; + scm_conf: syscon@104000 { + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; + reg = <0x00 0x00104000 0x00 0x18000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x00 0x00104000 0x18000>; + + usb_serdes_mux: mux-controller-0 { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */ + }; + }; + gic500: interrupt-controller@1800000 { compatible = "arm,gic-v3"; #address-cells = <2>;
@@ -726,6 +740,34 @@ cpts@310d0000 { }; }; + usbss0: cdns-usb@4104000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x04104000 0x00 0x100>; + clocks = <&k3_clks 360 16>, <&k3_clks 360 15>; + clock-names = "ref", "lpm"; + assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 360 17>; + power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-coherent; + + usb0: usb@6000000 { + compatible = "cdns,usb3"; + reg = <0x00 0x06000000 0x00 0x10000>, + <0x00 0x06010000 0x00 0x10000>, + <0x00 0x06020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host", "peripheral", "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + }; + main_mcan0: can@2701000 { compatible = "bosch,m_can"; reg = <0x00 0x02701000 0x00 0x200>,
Signature · 1 line
2.38.GIT
Re: [PATCH v5 1/8] arm64: dts: ti: k3-j721s2-main: Add support for USB
Quoted 62 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
Add support for single instance of USB 3.0 controller in J721S2 SoC.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 42 ++++++++++++++++++++++ 1 file changed, 42 insertions(+)arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +35
-0@@ -26,6 +26,20 @@ l3cache-sram@200000 { }; }; + scm_conf: syscon@104000 { + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; + reg = <0x00 0x00104000 0x00 0x18000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x00 0x00 0x00104000 0x18000>; + + usb_serdes_mux: mux-controller-0 { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */ + }; + }; + gic500: interrupt-controller@1800000 { compatible = "arm,gic-v3"; #address-cells = <2>;@@ -726,6 +740,34 @@ cpts@310d0000 { }; }; + usbss0: cdns-usb@4104000 { + compatible = "ti,j721e-usb"; + reg = <0x00 0x04104000 0x00 0x100>; + clocks = <&k3_clks 360 16>, <&k3_clks 360 15>; + clock-names = "ref", "lpm"; + assigned-clocks = <&k3_clks 360 16>; /* USB2_REFCLK */ + assigned-clock-parents = <&k3_clks 360 17>; + power-domains = <&k3_pds 360 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + dma-coherent; + + usb0: usb@6000000 { + compatible = "cdns,usb3"; + reg = <0x00 0x06000000 0x00 0x10000>, + <0x00 0x06010000 0x00 0x10000>, + <0x00 0x06020000 0x00 0x10000>; + reg-names = "otg", "xhci", "dev"; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi cpts@310d0000 { · line 773
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +7
-0+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "host", "peripheral", "otg"; + maximum-speed = "super-speed"; + dr_mode = "otg"; + }; + }; + main_mcan0: can@2701000 { compatible = "bosch,m_can"; reg = <0x00 0x02701000 0x00 0x200>,
Signature · 2 lines
Regards, Ravi
PATCH v5 2/8 arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
In reply to Matt RanostayAdd dt node for the single instance of WIZ (SERDES wrapper) and SERDES module shared by PCIe, eDP and USB.
--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 53 ++++++++++++++++++++++ 1 file changed, 53 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +53 -0
@@ -5,6 +5,16 @@ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ */ +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy-ti.h> + +/ { + serdes_refclk: clock-cmnrefclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; +}; + &cbass_main { msmc_ram: sram@70000000 { compatible = "mmio-sram";
@@ -38,6 +48,13 @@ usb_serdes_mux: mux-controller-0 { #mux-control-cells = <1>; mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */ }; + + serdes_ln_ctrl: mux-controller-80 { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */ + <0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */ + }; }; gic500: interrupt-controller@1800000 {
@@ -768,6 +785,42 @@ usb0: usb@6000000 { }; }; + serdes_wiz0: wiz@5060000 { + compatible = "ti,am64-wiz-10g"; + #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + num-lanes = <4>; + #reset-cells = <1>; + #clock-cells = <1>; + ranges = <0x5060000 0x0 0x5060000 0x10000>; + + assigned-clocks = <&k3_clks 365 3>; + assigned-clock-parents = <&k3_clks 365 7>; + + serdes0: serdes@5060000 { + compatible = "ti,j721e-serdes-10g"; + reg = <0x05060000 0x00010000>; + reg-names = "torrent_phy"; + resets = <&serdes_wiz0 0>; + reset-names = "torrent_reset"; + clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, + <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>; + clock-names = "refclk", "phy_en_refclk"; + assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, + <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>, + <&serdes_wiz0 TI_WIZ_REFCLK_DIG>; + assigned-clock-parents = <&k3_clks 365 3>, + <&k3_clks 365 3>, + <&k3_clks 365 3>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + }; + }; + main_mcan0: can@2701000 { compatible = "bosch,m_can"; reg = <0x00 0x02701000 0x00 0x200>,
Signature · 1 line
2.38.GIT
Re: [PATCH v5 2/8] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
Matt,
Quoted 46 lines · Matt Ranostay
Add dt node for the single instance of WIZ (SERDES wrapper) and SERDES module shared by PCIe, eDP and USB.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 53 ++++++++++++++++++++++ 1 file changed, 53 insertions(+)arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +17
-0@@ -5,6 +5,16 @@ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ */ +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy-ti.h> + +/ { + serdes_refclk: clock-cmnrefclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; +}; + &cbass_main { msmc_ram: sram@70000000 { compatible = "mmio-sram";@@ -38,6 +48,13 @@ usb_serdes_mux: mux-controller-0 { #mux-control-cells = <1>; mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */ }; + + serdes_ln_ctrl: mux-controller-80 { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */ + <0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */ + }; }; gic500: interrupt-controller@1800000 {
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi usb0: usb@6000000 { · line 789
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +2
-0@@ -768,6 +785,42 @@ usb0: usb@6000000 { }; }; + serdes_wiz0: wiz@5060000 { + compatible = "ti,am64-wiz-10g";
Should this be "ti,am64-wiz-10g" or "ti,j721e-wiz-10g" ?
Quoted 37 lines
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +34
-0+ #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + num-lanes = <4>; + #reset-cells = <1>; + #clock-cells = <1>; + ranges = <0x5060000 0x0 0x5060000 0x10000>; + + assigned-clocks = <&k3_clks 365 3>; + assigned-clock-parents = <&k3_clks 365 7>; + + serdes0: serdes@5060000 { + compatible = "ti,j721e-serdes-10g"; + reg = <0x05060000 0x00010000>; + reg-names = "torrent_phy"; + resets = <&serdes_wiz0 0>; + reset-names = "torrent_reset"; + clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, + <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>; + clock-names = "refclk", "phy_en_refclk"; + assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, + <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>, + <&serdes_wiz0 TI_WIZ_REFCLK_DIG>; + assigned-clock-parents = <&k3_clks 365 3>, + <&k3_clks 365 3>, + <&k3_clks 365 3>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + }; + }; + main_mcan0: can@2701000 { compatible = "bosch,m_can"; reg = <0x00 0x02701000 0x00 0x200>,
Signature · 2 lines
Regards, Ravi
Re: [PATCH v5 2/8] arm64: dts: ti: k3-j721s2-main: Add SERDES and WIZ device tree node
Quoted 53 lines · Ravi Gunasekaran
Matt,
Quoted 49 lines · Matt Ranostay
Add dt node for the single instance of WIZ (SERDES wrapper) and SERDES module shared by PCIe, eDP and USB.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 53 ++++++++++++++++++++++ 1 file changed, 53 insertions(+)arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +17
-0@@ -5,6 +5,16 @@ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/ */ +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy-ti.h> + +/ { + serdes_refclk: clock-cmnrefclk { + #clock-cells = <0>; + compatible = "fixed-clock"; + }; +}; + &cbass_main { msmc_ram: sram@70000000 { compatible = "mmio-sram";@@ -38,6 +48,13 @@ usb_serdes_mux: mux-controller-0 { #mux-control-cells = <1>; mux-reg-masks = <0x0 0x8000000>; /* USB0 to SERDES0 lane 1/3 mux */ }; + + serdes_ln_ctrl: mux-controller-80 { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x80 0x3>, <0x84 0x3>, /* SERDES0 lane0/1 select */ + <0x88 0x3>, <0x8c 0x3>; /* SERDES0 lane2/3 select */ + }; }; gic500: interrupt-controller@1800000 {@@ -768,6 +785,42 @@ usb0: usb@6000000 { }; };
Quoted 5 lines
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi usb0: usb@6000000 { · line 789
Quoted 2 lines
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +2
-0+ serdes_wiz0: wiz@5060000 { + compatible = "ti,am64-wiz-10g";Should this be "ti,am64-wiz-10g" or "ti,j721e-wiz-10g" ?
Using ti,am64-wiz-10g because that allows the newer clock scheme to be used.
- Matt
Quoted 41 lines
Quoted 37 lines
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +34
-0+ #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 365 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 365 0>, <&k3_clks 365 3>, <&serdes_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + num-lanes = <4>; + #reset-cells = <1>; + #clock-cells = <1>; + ranges = <0x5060000 0x0 0x5060000 0x10000>; + + assigned-clocks = <&k3_clks 365 3>; + assigned-clock-parents = <&k3_clks 365 7>; + + serdes0: serdes@5060000 { + compatible = "ti,j721e-serdes-10g"; + reg = <0x05060000 0x00010000>; + reg-names = "torrent_phy"; + resets = <&serdes_wiz0 0>; + reset-names = "torrent_reset"; + clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, + <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>; + clock-names = "refclk", "phy_en_refclk"; + assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>, + <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>, + <&serdes_wiz0 TI_WIZ_REFCLK_DIG>; + assigned-clock-parents = <&k3_clks 365 3>, + <&k3_clks 365 3>, + <&k3_clks 365 3>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <1>; + }; + }; + main_mcan0: can@2701000 { compatible = "bosch,m_can"; reg = <0x00 0x02701000 0x00 0x200>,Signature · 2 lines
Regards, Ravi
PATCH v5 3/8 arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI
In reply to Matt RanostayFrom: Aswath Govindraju <[email protected]>
Add support for two instance of OSPI in J721S2 SoC.
--- .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 40 +++++++++++++++++++ 1 file changed, 40 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +40 -0
@@ -306,4 +306,44 @@ cpts@3d000 { ti,cpts-periodic-outputs = <2>; }; }; + + fss: syscon@47000000 { + compatible = "syscon", "simple-mfd"; + reg = <0x0 0x47000000 0x0 0x100>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ospi0: spi@47040000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x47040000 0x00 0x100>, + <0x5 0x0000000 0x1 0x0000000>; + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 109 5>; + assigned-clocks = <&k3_clks 109 5>; + assigned-clock-parents = <&k3_clks 109 7>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + + ospi1: spi@47050000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x47050000 0x00 0x100>, + <0x7 0x0000000 0x1 0x0000000>; + interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 110 5>; + power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + + }; };
Signature · 1 line
2.38.GIT
Re: [PATCH v5 3/8] arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI
Quoted 17 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
Add support for two instance of OSPI in J721S2 SoC.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 40 +++++++++++++++++++ 1 file changed, 40 insertions(+)arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +0
-0
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi cpts@3d000 { · line 311
Quoted 6 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +3
-0@@ -306,4 +306,44 @@ cpts@3d000 { ti,cpts-periodic-outputs = <2>; }; }; + + fss: syscon@47000000 { + compatible = "syscon", "simple-mfd";
Looks like the update here to add "ti,j721e-system-controller" compatible is in PATCH 6/8, it could have been in the same patch here instead of editing the same node again in the series.
Quoted 28 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +28
-0+ reg = <0x0 0x47000000 0x0 0x100>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ospi0: spi@47040000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x47040000 0x00 0x100>, + <0x5 0x0000000 0x1 0x0000000>; + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 109 5>; + assigned-clocks = <&k3_clks 109 5>; + assigned-clock-parents = <&k3_clks 109 7>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + + ospi1: spi@47050000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x47050000 0x00 0x100>, + <0x7 0x0000000 0x1 0x0000000>; + interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>;
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi cpts@3d000 { · line 349
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +9
-0+ cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 110 5>; + power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + + }; };
Signature · 2 lines
Regards, Vaishnav
Re: [PATCH v5 3/8] arm64: dts: ti: k3-j721s2-mcu-wakeup: Add support of OSPI
Quoted 15 lines · Vaishnav Achath
Quoted 12 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
Add support for two instance of OSPI in J721S2 SoC.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 40 +++++++++++++++++++ 1 file changed, 40 insertions(+)
Quoted 16 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi cpts@3d000 { · line 311
Quoted 11 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +3
-0@@ -306,4 +306,44 @@ cpts@3d000 { ti,cpts-periodic-outputs = <2>; }; }; + + fss: syscon@47000000 { + compatible = "syscon", "simple-mfd";Looks like the update here to add "ti,j721e-system-controller" compatible is in PATCH 6/8, it could have been in the same patch here instead of editing the same node again in the series.
Will fix in next revision.
- Matt
Quoted 44 lines
Quoted 28 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +28
-0+ reg = <0x0 0x47000000 0x0 0x100>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + ospi0: spi@47040000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x47040000 0x00 0x100>, + <0x5 0x0000000 0x1 0x0000000>; + interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>; + cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 109 5>; + assigned-clocks = <&k3_clks 109 5>; + assigned-clock-parents = <&k3_clks 109 7>; + assigned-clock-rates = <166666666>; + power-domains = <&k3_pds 109 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + + ospi1: spi@47050000 { + compatible = "ti,am654-ospi", "cdns,qspi-nor"; + reg = <0x00 0x47050000 0x00 0x100>, + <0x7 0x0000000 0x1 0x0000000>; + interrupts = <GIC_SPI 841 IRQ_TYPE_LEVEL_HIGH>; + cdns,fifo-depth = <256>;arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi cpts@3d000 { · line 349
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +9
-0+ cdns,fifo-width = <4>; + cdns,trigger-address = <0x0>; + clocks = <&k3_clks 110 5>; + power-domains = <&k3_pds 110 TI_SCI_PD_EXCLUSIVE>; + #address-cells = <1>; + #size-cells = <0>; + }; + + }; };Reviewed-by Vaishnav Achath <[email protected]>Signature · 2 lines
Regards, Vaishnav
PATCH v5 4/8 arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0
In reply to Matt RanostayFrom: Aswath Govindraju <[email protected]>
Configure first lane to PCIe, the second lane to USB and the last two lanes to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is connected to PCIe.
--- .../dts/ti/k3-j721s2-common-proc-board.dts | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +22 -0
@@ -9,6 +9,9 @@ #include "k3-j721s2-som-p0.dtsi" #include <dt-bindings/net/ti-dp83867.h> +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/mux/ti-serdes.h> / { compatible = "ti,j721s2-evm", "ti,j721s2";
@@ -296,6 +299,25 @@ &cpsw_port1 { phy-handle = <&phy0>; }; +&serdes_ln_ctrl { + idle-states = <J721S2_SERDES0_LANE0_PCIE1_LANE0>, <J721S2_SERDES0_LANE1_USB>, + <J721S2_SERDES0_LANE2_EDP_LANE2>, <J721S2_SERDES0_LANE3_EDP_LANE3>; +}; + +&serdes_refclk { + clock-frequency = <100000000>; +}; + +&serdes0 { + serdes0_pcie_link: phy@0 { + reg = <0>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + resets = <&serdes_wiz0 1>; + }; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.38.GIT
Re: [PATCH v5 4/8] arm64: dts: ti: k3-j721s2-common-proc-board: Enable SERDES0
Quoted 44 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
Configure first lane to PCIe, the second lane to USB and the last two lanes to eDP. Also, add sub-nodes to SERDES0 DT node to represent SERDES0 is connected to PCIe.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- .../dts/ti/k3-j721s2-common-proc-board.dts | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+)arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +15
-0@@ -9,6 +9,9 @@ #include "k3-j721s2-som-p0.dtsi" #include <dt-bindings/net/ti-dp83867.h> +#include <dt-bindings/phy/phy-cadence.h> +#include <dt-bindings/phy/phy.h> +#include <dt-bindings/mux/ti-serdes.h> / { compatible = "ti,j721s2-evm", "ti,j721s2";@@ -296,6 +299,25 @@ &cpsw_port1 { phy-handle = <&phy0>; }; +&serdes_ln_ctrl { + idle-states = <J721S2_SERDES0_LANE0_PCIE1_LANE0>, <J721S2_SERDES0_LANE1_USB>, + <J721S2_SERDES0_LANE2_EDP_LANE2>, <J721S2_SERDES0_LANE3_EDP_LANE3>; +}; + +&serdes_refclk { + clock-frequency = <100000000>; +}; + +&serdes0 { + serdes0_pcie_link: phy@0 { + reg = <0>;
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts &cpsw_port1 { · line 323
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +7
-0+ cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + resets = <&serdes_wiz0 1>; + }; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";
Signature · 2 lines
Regards, Ravi
PATCH v5 5/8 arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
In reply to Matt RanostayFrom: Aswath Govindraju <[email protected]>
The board uses lane 1 of SERDES for USB. Set the mux accordingly.
The USB controller and EVM supports super-speed for USB0 on the Type-C port. However, the SERDES has a limitation that upto 2 protocols can be used at a time. The SERDES is wired for PCIe, eDP and USB super-speed. It has been chosen to use PCIe and eDP as default. So restrict USB0 to high-speed mode.
--- .../dts/ti/k3-j721s2-common-proc-board.dts | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +22 -0
@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */ >; }; + + main_usbss0_pins_default: main-usbss0-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */ + >; + }; }; &wkup_pmx0 {
@@ -318,6 +324,22 @@ serdes0_pcie_link: phy@0 { }; }; +&usb_serdes_mux { + idle-states = <1>; /* USB0 to SERDES lane 1 */ +}; + +&usbss0 { + pinctrl-0 = <&main_usbss0_pins_default>; + pinctrl-names = "default"; + ti,vbus-divider; + ti,usb2-only; +}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "high-speed"; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.38.GIT
Re: [PATCH v5 5/8] arm64: dts: ti: k3-j721s2-common-proc-board: Add USB support
Quoted 50 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
The board uses lane 1 of SERDES for USB. Set the mux accordingly.
The USB controller and EVM supports super-speed for USB0 on the Type-C port. However, the SERDES has a limitation that upto 2 protocols can be used at a time. The SERDES is wired for PCIe, eDP and USB super-speed. It has been chosen to use PCIe and eDP as default. So restrict USB0 to high-speed mode.
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- .../dts/ti/k3-j721s2-common-proc-board.dts | 22 +++++++++++++++++++ 1 file changed, 22 insertions(+)arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +15
-0@@ -147,6 +147,12 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default { J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */ >; }; + + main_usbss0_pins_default: main-usbss0-pins-default { + pinctrl-single,pins = < + J721S2_IOPAD(0x0ec, PIN_OUTPUT, 6) /* (AG25) TIMER_IO1.USB0_DRVVBUS */ + >; + }; }; &wkup_pmx0 {@@ -318,6 +324,22 @@ serdes0_pcie_link: phy@0 { }; }; +&usb_serdes_mux { + idle-states = <1>; /* USB0 to SERDES lane 1 */ +}; + +&usbss0 { + pinctrl-0 = <&main_usbss0_pins_default>; + pinctrl-names = "default"; + ti,vbus-divider; + ti,usb2-only;
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts serdes0_pcie_link: phy@0 { · line 345
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +7
-0+}; + +&usb0 { + dr_mode = "otg"; + maximum-speed = "high-speed"; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";
Signature · 2 lines
Regards, Ravi
PATCH v5 6/8 arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes
In reply to Matt RanostayFrom: Aswath Govindraju <[email protected]>
J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a QSPI NOR flash on the common processor board connected to the OSPI1 instance. Add support for the same
--- .../dts/ti/k3-j721s2-common-proc-board.dts | 34 +++++++++++++++ .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 +- arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 42 +++++++++++++++++++ 3 files changed, 78 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +34 -0
@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default { J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */ >; }; + + mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */ + J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */ + J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */ + J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */ + J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */ + J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */ + J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */ + J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */ + J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */ + >; + }; }; &main_gpio2 {
@@ -340,6 +354,26 @@ &usb0 { maximum-speed = "high-speed"; }; +&ospi1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi1_pins_default>; + + flash@0{ + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <40000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <2>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";
arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +2 -2
@@ -308,8 +308,8 @@ cpts@3d000 { }; fss: syscon@47000000 { - compatible = "syscon", "simple-mfd"; - reg = <0x0 0x47000000 0x0 0x100>; + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; + reg = <0x00 0x47000000 0x00 0x100>; #address-cells = <2>; #size-cells = <2>; ranges;
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi +42 -0
51 lines not on this page · raw message
Signature · 1 line
2.38.GIT
Re: [PATCH v5 6/8] arm64: dts: ti: k3-j721s2: Add support for OSPI Flashes
Quoted 129 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
J721S2 has an OSPI NOR flash on its SOM connected the OSPI0 instance and a QSPI NOR flash on the common processor board connected to the OSPI1 instance. Add support for the same
Cc Vignesh Raghavendra <[email protected]>Cc Nishanth Menon <[email protected]>Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- .../dts/ti/k3-j721s2-common-proc-board.dts | 34 +++++++++++++++ .../boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 +- arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi | 42 +++++++++++++++++++ 3 files changed, 78 insertions(+), 2 deletions(-)arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +34
-0@@ -206,6 +206,20 @@ mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default { J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */ >; }; + + mcu_fss0_ospi1_pins_default: mcu-fss0-ospi1-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x040, PIN_OUTPUT, 0) /* (A19) MCU_OSPI1_CLK */ + J721S2_WKUP_IOPAD(0x05c, PIN_OUTPUT, 0) /* (D20) MCU_OSPI1_CSn0 */ + J721S2_WKUP_IOPAD(0x060, PIN_OUTPUT, 0) /* (C21) MCU_OSPI1_CSn1 */ + J721S2_WKUP_IOPAD(0x04c, PIN_INPUT, 0) /* (D21) MCU_OSPI1_D0 */ + J721S2_WKUP_IOPAD(0x050, PIN_INPUT, 0) /* (G20) MCU_OSPI1_D1 */ + J721S2_WKUP_IOPAD(0x054, PIN_INPUT, 0) /* (C20) MCU_OSPI1_D2 */ + J721S2_WKUP_IOPAD(0x058, PIN_INPUT, 0) /* (A20) MCU_OSPI1_D3 */ + J721S2_WKUP_IOPAD(0x048, PIN_INPUT, 0) /* (B19) MCU_OSPI1_DQS */ + J721S2_WKUP_IOPAD(0x044, PIN_INPUT, 0) /* (B20) MCU_OSPI1_LBCLKO */ + >; + }; }; &main_gpio2 {@@ -340,6 +354,26 @@ &usb0 { maximum-speed = "high-speed"; }; +&ospi1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi1_pins_default>; + + flash@0{ + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <1>; + spi-rx-bus-width = <4>; + spi-max-frequency = <40000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <2>; + #address-cells = <1>; + #size-cells = <1>; + }; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +2
-2@@ -308,8 +308,8 @@ cpts@3d000 { }; fss: syscon@47000000 { - compatible = "syscon", "simple-mfd"; - reg = <0x0 0x47000000 0x0 0x100>; + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd"; + reg = <0x00 0x47000000 0x00 0x100>; #address-cells = <2>; #size-cells = <2>; ranges;arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi +31
-0@@ -39,6 +39,28 @@ transceiver0: can-phy0 { }; }; +&wkup_pmx0 { + mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default { + pinctrl-single,pins = < + J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (D19) MCU_OSPI0_CLK */ + J721S2_WKUP_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F15) MCU_OSPI0_CSn0 */ + J721S2_WKUP_IOPAD(0x030, PIN_OUTPUT, 0) /* (G17) MCU_OSPI0_CSn1 */ + J721S2_WKUP_IOPAD(0x038, PIN_OUTPUT, 0) /* (F14) MCU_OSPI0_CSn2 */ + J721S2_WKUP_IOPAD(0x03c, PIN_OUTPUT, 0) /* (F17) MCU_OSPI0_CSn3 */ + J721S2_WKUP_IOPAD(0x00c, PIN_INPUT, 0) /* (C19) MCU_OSPI0_D0 */ + J721S2_WKUP_IOPAD(0x010, PIN_INPUT, 0) /* (F16) MCU_OSPI0_D1 */ + J721S2_WKUP_IOPAD(0x014, PIN_INPUT, 0) /* (G15) MCU_OSPI0_D2 */ + J721S2_WKUP_IOPAD(0x018, PIN_INPUT, 0) /* (F18) MCU_OSPI0_D3 */ + J721S2_WKUP_IOPAD(0x01c, PIN_INPUT, 0) /* (E19) MCU_OSPI0_D4 */ + J721S2_WKUP_IOPAD(0x020, PIN_INPUT, 0) /* (G19) MCU_OSPI0_D5 */ + J721S2_WKUP_IOPAD(0x024, PIN_INPUT, 0) /* (F19) MCU_OSPI0_D6 */ + J721S2_WKUP_IOPAD(0x028, PIN_INPUT, 0) /* (F20) MCU_OSPI0_D7 */ + J721S2_WKUP_IOPAD(0x008, PIN_INPUT, 0) /* (E18) MCU_OSPI0_DQS */ + J721S2_WKUP_IOPAD(0x004, PIN_INPUT, 0) /* (E20) MCU_OSPI0_LBCLKO */ + >; + }; +}; + &main_pmx0 { main_i2c0_pins_default: main-i2c0-pins-default { pinctrl-single,pins = <@@ -79,3 +101,23 @@ &main_mcan16 { pinctrl-names = "default"; phys = <&transceiver0>; }; + +&ospi0 { + pinctrl-names = "default"; + pinctrl-0 = <&mcu_fss0_ospi0_pins_default>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0x0>; + spi-tx-bus-width = <8>;
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi &main_mcan16 { · line 122
Quoted 10 lines
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi +10
-0+ spi-rx-bus-width = <8>; + spi-max-frequency = <25000000>; + cdns,tshsl-ns = <60>; + cdns,tsd2d-ns = <60>; + cdns,tchsh-ns = <60>; + cdns,tslch-ns = <60>; + cdns,read-delay = <4>; + #address-cells = <1>; + #size-cells = <1>; + };
Quoted 1 line
arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi +1
-0+};
Signature · 2 lines
Regards, Vaishnav
PATCH v5 7/8 arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node
In reply to Matt RanostayFrom: Aswath Govindraju <[email protected]>
Add PCIe device tree node (both RC and EP) for the single PCIe instance present in j721s2.
--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 61 ++++++++++++++++++++++ 1 file changed, 61 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi +61 -0
@@ -821,6 +821,67 @@ serdes0: serdes@5060000 { }; }; + pcie1_rc: pcie@2910000 { + compatible = "ti,j7200-pcie-host", "ti,j721e-pcie-host"; + reg = <0x00 0x02910000 0x00 0x1000>, + <0x00 0x02917000 0x00 0x400>, + <0x00 0x0d800000 0x00 0x00800000>, + <0x00 0x18000000 0x00 0x00001000>; + reg-names = "intd_cfg", "user_cfg", "reg", "cfg"; + interrupt-names = "link_state"; + interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>; + device_type = "pci"; + ti,syscon-pcie-ctrl = <&scm_conf 0x074>; + max-link-speed = <3>; + num-lanes = <4>; + power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 276 41>; + clock-names = "fck"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xff>; + vendor-id = <0x104c>; + device-id = <0xb013>; + msi-map = <0x0 &gic_its 0x0 0x10000>; + dma-coherent; + ranges = <0x01000000 0x0 0x18001000 0x00 0x18001000 0x0 0x0010000>, + <0x02000000 0x0 0x18011000 0x00 0x18011000 0x0 0x7fef000>; + dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie1_intc 0>, /* INT A */ + <0 0 0 2 &pcie1_intc 0>, /* INT B */ + <0 0 0 3 &pcie1_intc 0>, /* INT C */ + <0 0 0 4 &pcie1_intc 0>; /* INT D */ + + pcie1_intc: interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic500>; + interrupts = <GIC_SPI 324 IRQ_TYPE_EDGE_RISING>; + }; + }; + + pcie1_ep: pcie-ep@2910000 { + compatible = "ti,j7200-pcie-ep", "ti,j721e-pcie-ep"; + reg = <0x00 0x02910000 0x00 0x1000>, + <0x00 0x02917000 0x00 0x400>, + <0x00 0x0d800000 0x00 0x00800000>, + <0x00 0x18000000 0x00 0x08000000>; + reg-names = "intd_cfg", "user_cfg", "reg", "mem"; + interrupt-names = "link_state"; + interrupts = <GIC_SPI 330 IRQ_TYPE_EDGE_RISING>; + ti,syscon-pcie-ctrl = <&scm_conf 0x074>; + max-link-speed = <3>; + num-lanes = <4>; + power-domains = <&k3_pds 276 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 276 41>; + clock-names = "fck"; + max-functions = /bits/ 8 <6>; + max-virtual-functions = /bits/ 8 <4 4 4 4 0 0>; + dma-coherent; + }; + main_mcan0: can@2701000 { compatible = "bosch,m_can"; reg = <0x00 0x02701000 0x00 0x200>,
Signature · 1 line
2.38.GIT
Re: [PATCH v5 7/8] arm64: dts: ti: k3-j721s2-main: Add PCIe device tree node
Quoted 11 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
Add PCIe device tree node (both RC and EP) for the single PCIe instance present in j721s2.
Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Vignesh Raghavendra <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 61 ++++++++++++++++++++++ 1 file changed, 61 insertions(+)
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v5 8/8 arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe
In reply to Matt RanostayFrom: Aswath Govindraju <[email protected]>
x1 lane PCIe slot in the common processor board is enabled and connected to J721S2 SOM. Add PCIe DT node in common processor board to reflect the same.
--- .../boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts +14 -0
@@ -374,6 +374,20 @@ flash@0{ }; }; +&pcie1_rc { + reset-gpios = <&exp1 2 GPIO_ACTIVE_HIGH>; + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <1>; +}; + +&pcie1_ep { + phys = <&serdes0_pcie_link>; + phy-names = "pcie-phy"; + num-lanes = <1>; + status = "disabled"; +}; + &mcu_mcan0 { status = "okay"; pinctrl-names = "default";
Signature · 1 line
2.38.GIT
Re: [PATCH v5 8/8] arm64: dts: ti: k3-j721s2-common-proc-board: Enable PCIe
Quoted 6 lines · Matt Ranostay
From: Aswath Govindraju <[email protected]>
x1 lane PCIe slot in the common processor board is enabled and connected to J721S2 SOM. Add PCIe DT node in common processor board to reflect the same.
Quoted 6 lines
Signed-off-by Aswath Govindraju <[email protected]>Signed-off-by Vignesh Raghavendra <[email protected]>Signed-off-by Matt Ranostay <[email protected]>--- .../boot/dts/ti/k3-j721s2-common-proc-board.dts | 14 ++++++++++++++ 1 file changed, 14 insertions(+)
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel