Skip to contentSkip to conversation

support all dataflash for at91sam9g20ek_2mmc

U-Boot John Stile 1 participant 2 messages Feb 14, 2013 Arm/Microchip (AT91) SoC support

lore
Share & tools
lore

John Stile

author
#0 lore raw

I am using uboot-2013.01, with at91sam9g20ek_2mmc and I am trying to build for dataflash, using at91bootstrap-1.16, and buildroot-2011.11

Initially I built for nand flash, with a patch to boards.cfg and at91sam9260ek.c

This was fine if I used the reset button, but from a cold boot, startup stopped after after at91bootstrap-1.16, and uboot never starts.

Now I am trying to build uboot for all dataflash, but I still see the same behavior with uboot.

Uboot worked from dataflash when using uboot-1.3.6 (and patches from atmel), but much has changed since then, so it is hard to figure out if something from those patches is lost in the current uboot.

What can I try next.

Bellow are the patches I applied so far.

boards.cfg: add target name at91sam9g20ek_2mmc_nandflash,at91sam9g20ek_2mmc_dataflash_cs0,at91sam9g20ek_2mmc_dataflash_cs1

signed-off-by John Stile <[email protected]>

boards.cfg 2013-02-13 18:09:32.000000000 -0800 renamed from boards.cfg 2013-02-14 07:08:12.000000000 -0800 +0 -0
diff -ruNp a/boards.cfg b/boards.cfg
@@ -91,7 +91,10 @@ at91sam9263ek_norflash       arm
 at91sam9263ek_norflash_boot  arm         arm926ejs   at91sam9263ek

atmel at91
at91sam9263ek:AT91SAM9263,SYS_USE_BOOT_NORFLASH
at91sam9g10ek_dataflash_cs0 arm arm926ejs at91sam9261ek
atmel at91
at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS0
at91sam9g10ek_dataflash_cs3 arm arm926ejs at91sam9261ek
atmel at91
at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS3
+at91sam9g20ek_2mmc_dataflash_cs0 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_DATAFLASH_CS0
+at91sam9g20ek_2mmc_dataflash_cs1 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_DATAFLASH_CS1
at91sam9g10ek_nandflash arm arm926ejs at91sam9261ek
atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_NANDFLASH
+at91sam9g20ek_2mmc_nandflash arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_NANDFLASH
at91sam9g20ek_dataflash_cs0 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0
at91sam9g20ek_dataflash_cs1 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1
at91sam9g20ek_nandflash arm arm926ejs at91sam9260ek
atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH

board/atmel/at91sam9260ek/at91sam9260ek.c Added ability to make buildroot with correct board type, to match kernel

signed-off-by John Stile <[email protected]>

board/atmel/at91sam9260ek/at91sam9260ek.c +5 -0
diff -ruNp a/board/atmel/at91sam9260ek/at91sam9260ek.c b/board/atmel/at91sam9260ek/at91sam9260ek.c
@@ -157,6 +157,10 @@
 
 int board_init(void)
 {
+#ifdef CONFIG_AT91SAM9G20EK_2MMC
+       /* arch number of AT91SAM9260EK-Board */
+       gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK_2MMC;
+#else
 #ifdef CONFIG_AT91SAM9G20EK
 	/* arch number of AT91SAM9260EK-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G20EK;
@@ -164,6 +168,7 @@
 	/* arch number of AT91SAM9260EK-Board */
 	gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9260EK;
 #endif
+#endif
 	/* adress of boot parameters */
 	gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
 
author
#1 lore raw
Quoted 9 lines · John Stile

I am using uboot-2013.01, with at91sam9g20ek_2mmc and I am trying to build for dataflash, using at91bootstrap-1.16, and buildroot-2011.11

Initially I built for nand flash, with a patch to boards.cfg and at91sam9260ek.c

This was fine if I used the reset button, but from a cold boot, startup stopped after after at91bootstrap-1.16, and uboot never starts.

Quoted 9 lines

Now I am trying to build uboot for all dataflash, but I still see the same behavior with uboot.

Uboot worked from dataflash when using uboot-1.3.6 (and patches from atmel), but much has changed since then, so it is hard to figure out if something from those patches is lost in the current uboot.

What can I try next.

I have gone over the patch list for uboot-1.3.6, and tracked down where they are moved to in uboot-2013.01, and nothing is jumping out at me yet, except these different:

uboot-1.3.6:
#define AT91_SLOW_CLOCK 32768 /* slow clock */
#define AT91_MAIN_CLOCK 198656000 /* from 18.432 MHz crystal */
#define AT91_MASTER_CLOCK 99328000 /* peripheral = main / 2 */
#define CFG_HZ 1000000 /* 1us resolution */
#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)

uboot-2013.01:
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */
#define CONFIG_SYS_HZ 1000
Though include/configs/cpuat91.h
#define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3)
#define CFG_SPI_WRITE_TOUT (5*CFG_HZ)

Q1: should I change Hz from 1000 to 1000000?
Q2: should I change MAIN_CLOCK from 18432000 to 198656000?
Q3: why is MASTER_CLOCK in old using divisor of 2, where new is using a divisor of 3?