support all dataflash for at91sam9g20ek_2mmc
I am using uboot-2013.01, with at91sam9g20ek_2mmc and I am trying to build for dataflash, using at91bootstrap-1.16, and buildroot-2011.11
Initially I built for nand flash, with a patch to boards.cfg and at91sam9260ek.c
This was fine if I used the reset button, but from a cold boot, startup stopped after after at91bootstrap-1.16, and uboot never starts.
Now I am trying to build uboot for all dataflash, but I still see the same behavior with uboot.
Uboot worked from dataflash when using uboot-1.3.6 (and patches from atmel), but much has changed since then, so it is hard to figure out if something from those patches is lost in the current uboot.
What can I try next.
Bellow are the patches I applied so far.
boards.cfg: add target name at91sam9g20ek_2mmc_nandflash,at91sam9g20ek_2mmc_dataflash_cs0,at91sam9g20ek_2mmc_dataflash_cs1
signed-off-by John Stile <[email protected]>
boards.cfg 2013-02-13 18:09:32.000000000 -0800 renamed from boards.cfg 2013-02-14 07:08:12.000000000 -0800 +0 -0
@@ -91,7 +91,10 @@ at91sam9263ek_norflash arm at91sam9263ek_norflash_boot arm arm926ejs at91sam9263ek
atmel at91
at91sam9263ek:AT91SAM9263,SYS_USE_BOOT_NORFLASH
at91sam9g10ek_dataflash_cs0 arm arm926ejs at91sam9261ek
atmel at91
at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS0
at91sam9g10ek_dataflash_cs3 arm arm926ejs at91sam9261ek
atmel at91
at91sam9261ek:AT91SAM9G10,SYS_USE_DATAFLASH_CS3
+at91sam9g20ek_2mmc_dataflash_cs0 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_DATAFLASH_CS0
+at91sam9g20ek_2mmc_dataflash_cs1 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_DATAFLASH_CS1
at91sam9g10ek_nandflash arm arm926ejs at91sam9261ek
atmel at91 at91sam9261ek:AT91SAM9G10,SYS_USE_NANDFLASH
+at91sam9g20ek_2mmc_nandflash arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,AT91SAM9G20EK_2MMC,SYS_USE_NANDFLASH
at91sam9g20ek_dataflash_cs0 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS0
at91sam9g20ek_dataflash_cs1 arm arm926ejs at91sam9260ek
atmel at91
at91sam9260ek:AT91SAM9G20,SYS_USE_DATAFLASH_CS1
at91sam9g20ek_nandflash arm arm926ejs at91sam9260ek
atmel at91 at91sam9260ek:AT91SAM9G20,SYS_USE_NANDFLASH
board/atmel/at91sam9260ek/at91sam9260ek.c Added ability to make buildroot with correct board type, to match kernel
signed-off-by John Stile <[email protected]>
board/atmel/at91sam9260ek/at91sam9260ek.c +5 -0
@@ -157,6 +157,10 @@int board_init (void ) { +#ifdef CONFIG_AT91SAM9G20EK_2MMC +/* arch number of AT91SAM9260EK-Board */ + gd->bd->bi_arch_number =MACH_TYPE_AT91SAM9G20EK_2MMC ; +#else #ifdef CONFIG_AT91SAM9G20EK /* arch number of AT91SAM9260EK-Board */ gd->bd->bi_arch_number =MACH_TYPE_AT91SAM9G20EK ;
@@ -164,6 +168,7 @@/* arch number of AT91SAM9260EK-Board */ gd->bd->bi_arch_number =MACH_TYPE_AT91SAM9260EK ;#endif +#endif /* adress of boot parameters */ gd->bd->bi_boot_params =CONFIG_SYS_SDRAM_BASE +0x100 ;
Quoted 9 lines · John Stile
I am using uboot-2013.01, with
at91sam9g20ek_2mmcand I am trying to build for dataflash, using at91bootstrap-1.16, and buildroot-2011.11Initially I built for nand flash, with a patch to boards.cfg and
at91sam9260ek.cThis was fine if I used the reset button, but from a cold boot, startup stopped after after at91bootstrap-1.16, and uboot never starts.
Quoted 9 lines
Now I am trying to build uboot for all dataflash, but I still see the same behavior with uboot.
Uboot worked from dataflash when using uboot-1.3.6 (and patches from atmel), but much has changed since then, so it is hard to figure out if something from those patches is lost in the current uboot.
What can I try next.
I have gone over the patch list for uboot-1.3.6, and tracked down where they are moved to in uboot-2013.01, and nothing is jumping out at me yet, except these different:
uboot-1.3.6:
#define AT91_SLOW_CLOCK 32768 /* slow clock */
#define AT91_MAIN_CLOCK 198656000 /* from 18.432 MHz crystal */
#define AT91_MASTER_CLOCK 99328000 /* peripheral = main / 2 */
#define CFG_HZ 1000000 /* 1us resolution */
#define CONFIG_SYS_SPI_WRITE_TOUT (5*CONFIG_SYS_HZ)
uboot-2013.01:
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
#define CONFIG_SYS_AT91_MAIN_CLOCK 18432000 /* main clock xtal */
#define CONFIG_SYS_HZ 1000
Though include/configs/cpuat91.h
#define AT91C_MASTER_CLOCK (AT91C_MAIN_CLOCK / 3)
#define CFG_SPI_WRITE_TOUT (5*CFG_HZ)
Q1: should I change Hz from 1000 to 1000000?
Q2: should I change MAIN_CLOCK from 18432000 to 198656000?
Q3: why is MASTER_CLOCK in old using divisor of 2, where new is using a divisor of 3?