Skip to contentSkip to conversation

blackfin: bf609: implement soft switch

PATCH Superseded Sonic Zhang 2 participants 4 messages Feb 27, 2013 – May 13, 2013

v1 of 2 Superseded Latest is v2 →

lore
Share & tools
lore
#0 lore raw

PATCH 1/2 blackfin: bf609: implement soft switch

From: Sonic Zhang <[email protected]>

Set up soft switch pins properly in board init code.

---
 board/bf609-ezkit/soft_switch.c |  180 +++++++++++++++++++++++++++++++++++++++
 board/bf609-ezkit/soft_switch.h |   71 +++++++++++++++
 2 files changed, 251 insertions(+), 0 deletions(-)
 create mode 100644 board/bf609-ezkit/soft_switch.c
 create mode 100644 board/bf609-ezkit/soft_switch.h
board/bf609-ezkit/soft_switch.c new file +180 -0
new file mode 100644
index 0000000..2e1404f
@@ -0,0 +1,180 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2011 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <asm/blackfin.h>
+#include <asm/io.h>
+#include <i2c.h>
+#include "soft_switch.h"
+
+#define SWITCH_ADDR     0x21
+
+#define NUM_SWITCH      3
+#define IODIRA          0x0
+#define IODIRB          0x1
+#define OLATA           0x14
+#define OLATB           0x15
+
+struct switch_config {
+	uchar dir0; /* IODIRA */
+	uchar dir1; /* IODIRB */
+	uchar value0; /* OLATA */
+	uchar value1; /* OLATB */
+};
+
+static struct switch_config switch_config_array[NUM_SWITCH] = {
+	{
+/*
+	U45 Port A                     U45 Port B
+
+	7---------------  RMII_CLK_EN  |  7--------------- ~TEMP_THERM_EN
+	| 6------------- ~CNT0ZM_EN    |  | 6------------- ~TEMP_IRQ_EN
+	| | 5----------- ~CNT0DG_EN    |  | | 5----------- ~UART0CTS_146_EN
+	| | | 4--------- ~CNT0UD_EN    |  | | | 4--------- ~UART0CTS_RST_EN
+	| | | | 3------- ~CAN0RX_EN    |  | | | | 3------- ~UART0CTS_RTS_LPBK
+	| | | | | 2----- ~CAN0_ERR_EN  |  | | | | | 2----- ~UART0CTS_EN
+	| | | | | | 1--- ~CAN_STB      |  | | | | | | 1--- ~UART0RX_EN
+	| | | | | | | 0-  CAN_EN       |  | | | | | | | 0- ~UART0RTS_EN
+	| | | | | | | |                |  | | | | | | | |
+	O O O O O O O O                |  O O O O O O O O   (I/O direction)
+	1 0 0 0 0 0 1 1                |  1 1 1 1 1 0 0 0   (value being set)
+*/
+		.dir0 = 0x0, /* all output */
+		.dir1 = 0x0, /* all output */
+		.value0 = RMII_CLK_EN | CAN_STB | CAN_EN,
+		.value1 = TEMP_THERM_EN | TEMP_IRQ_EN | UART0CTS_146_EN
+				| UART0CTS_RST_EN | UART0CTS_RTS_LPBK,
+	},
+	{
+/*
+	U46 Port A                       U46 Port B
+
+	7--------------- ~LED4_GPIO_EN   |  7---------------  EMPTY
+	| 6------------- ~LED3_GPIO_EN   |  | 6------------- ~SPI0D3_EN
+	| | 5----------- ~LED2_GPIO_EN   |  | | 5----------- ~SPI0D2_EN
+	| | | 4--------- ~LED1_GPIO_EN   |  | | | 4--------- ~SPIFLASH_CS_EN
+	| | | | 3-------  SMC0_LP0_EN    |  | | | | 3------- ~SD_WP_EN
+	| | | | | 2-----  EMPTY          |  | | | | | 2----- ~SD_CD_EN
+	| | | | | | 1---  SMC0_EPPI2     |  | | | | | | 1--- ~PUSHBUTTON2_EN
+			  _LP1_SWITCH
+	| | | | | | | 0-  OVERRIDE_SMC0  |  | | | | | | | 0- ~PUSHBUTTON1_EN
+			  _LP0_BOOT
+	| | | | | | | |                  |  | | | | | | | |
+	O O O O O O O O                  |  O O O O O O O O   (I/O direction)
+	0 0 0 0 0 X 0 1                  |  X 0 0 0 0 0 0 0   (value being set)
+*/
+		.dir0 = 0x0, /* all output */
+		.dir1 = 0x0, /* all output */
+#ifdef CONFIG_BFIN_LINKPORT
+		.value0 = OVERRIDE_SMC0_LP0_BOOT,
+#else
+		.value0 = SMC0_EPPI2_LP1_SWITCH,
+#endif
+		.value1 = 0x0,
+	},
+	{
+/*
+	U47 Port A                         U47 Port B
+
+	7--------------- ~PD2_SPI0MISO |  7---------------  EMPTY
+			  _EI3_EN
+	| 6------------- ~PD1_SPI0D3   |  | 6-------------  EMPTY
+			  _EPPI1D17
+			  _SPI0SEL2
+			  _EI3_EN
+	| | 5----------- ~PD0_SPI0D2   |  | | 5-----------  EMPTY
+			  _EPPI1D16
+			  _SPI0SEL3
+			  _EI3_EN
+	| | | 4--------- ~WAKE_PUSH    |  | | | 4---------  EMPTY
+			  BUTTON_EN
+	| | | | 3------- ~ETHERNET_EN  |  | | | | 3-------  EMPTY
+	| | | | | 2-----  PHYAD0       |  | | | | | 2-----  EMPTY
+	| | | | | | 1---  PHY_PWR      |  | | | | | | 1--- ~PD4_SPI0CK_EI3_EN
+			  _DWN_INT
+	| | | | | | | 0- ~PHYINT_EN    |  | | | | | | | 0- ~PD3_SPI0MOSI_EI3_EN
+	| | | | | | | |                |  | | | | | | | |
+	O O O O O I I O                |  O O O O O O O O   (I/O direction)
+	1 1 1 0 0 0 0 0                |  X X X X X X 1 1   (value being set)
+*/
+		.dir0 = 0x6, /* bits 1 and 2 input, all others output */
+		.dir1 = 0x0, /* all output */
+		.value0 = PD1_SPI0D3_EN | PD0_SPI0D2_EN,
+		.value1 = 0,
+	},
+};
+
+static int setup_soft_switch(int addr, struct switch_config *config)
+{
+	int ret = 0;
+
+	ret = i2c_write(addr, OLATA, 1, &config->value0, 1);
+	if (ret)
+		return ret;
+	ret = i2c_write(addr, OLATB, 1, &config->value1, 1);
+	if (ret)
+		return ret;
+
+	ret = i2c_write(addr, IODIRA, 1, &config->dir0, 1);
+	if (ret)
+		return ret;
+	return i2c_write(addr, IODIRB, 1, &config->dir1, 1);
+}
+
+int config_switch_bit(int num, int port, int bit, int dir, uchar value)
+{
+	int addr = SWITCH_ADDR + num;
+	int ret, data_reg, dir_reg;
+	uchar tmp;
+
+	if (port == IO_PORT_A) {
+		data_reg = OLATA;
+		dir_reg = IODIRA;
+	} else {
+		data_reg = OLATB;
+		dir_reg = IODIRB;
+	}
+
+	if (dir == IO_PORT_INPUT) {
+		ret = i2c_read(addr, dir_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		tmp |= bit;
+		return i2c_write(addr, dir_reg, 1, &tmp, 1);
+	} else {
+		ret = i2c_read(addr, data_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		if (value)
+			tmp |= bit;
+		else
+			tmp &= ~bit;
+		ret = i2c_write(addr, data_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		ret = i2c_read(addr, dir_reg, 1, &tmp, 1);
+		if (ret)
+			return ret;
+		tmp &= ~bit;
+		return i2c_write(addr, dir_reg, 1, &tmp, 1);
+	}
+}
+
+int setup_board_switches(void)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < NUM_SWITCH; i++) {
+		ret = setup_soft_switch(SWITCH_ADDR + i,
+				&switch_config_array[i]);
+		if (ret)
+			return ret;
+	}
+	return 0;
+}
board/bf609-ezkit/soft_switch.h new file +71 -0

71 lines not on this page · raw message

Signature · 1 line
1.7.0.4
#1 lore raw

PATCH 2/2 blackfin: bf609: add softswitch config command

From: Bob Liu <[email protected]>

Add softswitch_output command for bf609-ezkit to enable softswitches.

---
 arch/blackfin/include/asm/soft_switch.h |   18 +++++++++++++
 board/bf609-ezkit/soft_switch.c         |   11 +-------
 board/bf609-ezkit/soft_switch.h         |   25 +++++++++++++------
 common/Makefile                         |    1 +
 common/cmd_softswitch.c                 |   41 +++++++++++++++++++++++++++++++
 include/configs/bf609-ezkit.h           |    1 +
 6 files changed, 79 insertions(+), 18 deletions(-)
 create mode 100644 arch/blackfin/include/asm/soft_switch.h
 create mode 100644 common/cmd_softswitch.c
arch/blackfin/include/asm/soft_switch.h new file +18 -0
new file mode 100644
index 0000000..ff8e44d
@@ -0,0 +1,18 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __SOFT_SWITCH_H__
+#define __SOFT_SWITCH_H__
+
+#define IO_PORT_A              0
+#define IO_PORT_B              1
+#define IO_PORT_INPUT          0
+#define IO_PORT_OUTPUT         1
+
+int config_switch_bit(int num, int port, int bit, int dir, uchar value);
+#endif
board/bf609-ezkit/soft_switch.c +1 -10
index 2e1404f..e0c8d93 100644
@@ -12,14 +12,6 @@
 #include <i2c.h>
 #include "soft_switch.h"
 
-#define SWITCH_ADDR     0x21
-
-#define NUM_SWITCH      3
-#define IODIRA          0x0
-#define IODIRB          0x1
-#define OLATA           0x14
-#define OLATB           0x15
-
 struct switch_config {
 	uchar dir0; /* IODIRA */
 	uchar dir1; /* IODIRB */
@@ -126,9 +118,8 @@ static int setup_soft_switch(int addr, struct switch_config *config)
 	return i2c_write(addr, IODIRB, 1, &config->dir1, 1);
 }
 
-int config_switch_bit(int num, int port, int bit, int dir, uchar value)
+int config_switch_bit(int addr, int port, int bit, int dir, uchar value)
 {
-	int addr = SWITCH_ADDR + num;
 	int ret, data_reg, dir_reg;
 	uchar tmp;
 
board/bf609-ezkit/soft_switch.h +17 -8
index 8da0e44..d147fe1 100644
@@ -6,8 +6,10 @@
  * Licensed under the GPL-2 or later.
  */
 
-#ifndef __SOFT_SWITCH_H__
-#define __SOFT_SWITCH_H__
+#ifndef __BOARD_SOFT_SWITCH_H__
+#define __BOARD_SOFT_SWITCH_H__
+
+#include <asm/soft_switch.h>
 
 /* switch 0 port A */
 #define CAN_EN                 0x1
@@ -61,11 +63,18 @@
 #define PD3_SPI0MOSI_EN        0x1
 #define PD4_SPI0CK_EN          0x2
 
-#define IO_PORT_A              0
-#define IO_PORT_B              1
-#define IO_PORT_INPUT          0
-#define IO_PORT_OUTPUT         1
+#ifdef CONFIG_BFIN_BOARD_VERSION_1_0
+#define SWITCH_ADDR     0x21
+#else
+#define SWITCH_ADDR     0x20
+#endif
+
+#define NUM_SWITCH      3
+#define IODIRA          0x0
+#define IODIRB          0x1
+#define OLATA           0x14
+#define OLATB           0x15
 
-int config_switch_bit(int num, int port, int bit, int dir, uchar value);
 int setup_board_switches(void);
-#endif
+
+#endif /* __BOARD_SOFT_SWITCH_H__ */
common/Makefile +1 -0
index 54fcc81..80fee78 100644
@@ -157,6 +157,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o
 COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o
 COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o
 COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o
+COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o
 COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o
 COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o
 COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.o
common/cmd_softswitch.c new file +41 -0

41 lines not on this page · raw message

include/configs/bf609-ezkit.h +1 -0
index 8b90129..f0ac86b 100644
@@ -144,6 +144,7 @@
 #define CONFIG_UART_CONSOLE	0
 
 #define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_SOFTSWITCH
 
 #define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)
 #define CONFIG_BFIN_SOFT_SWITCH
Signature · 1 line
1.7.0.4
#2 lore raw

PATCH 2/2 blackfin: bf609: add softswitch config command

Hi Tom

Quoted 185 lines · Sonic Zhang

From: Bob Liu <[email protected]>

Add softswitch_output command for bf609-ezkit to enable softswitches.

---
 arch/blackfin/include/asm/soft_switch.h |   18 +++++++++++++
 board/bf609-ezkit/soft_switch.c         |   11 +-------
 board/bf609-ezkit/soft_switch.h         |   25 +++++++++++++------
 common/Makefile                         |    1 +
 common/cmd_softswitch.c                 |   41 +++++++++++++++++++++++++++++++
 include/configs/bf609-ezkit.h           |    1 +
 6 files changed, 79 insertions(+), 18 deletions(-)
 create mode 100644 arch/blackfin/include/asm/soft_switch.h
 create mode 100644 common/cmd_softswitch.c
arch/blackfin/include/asm/soft_switch.h new file +18 -0
new file mode 100644
index 0000000..ff8e44d
@@ -0,0 +1,18 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __SOFT_SWITCH_H__
+#define __SOFT_SWITCH_H__
+
+#define IO_PORT_A              0
+#define IO_PORT_B              1
+#define IO_PORT_INPUT          0
+#define IO_PORT_OUTPUT         1
+
+int config_switch_bit(int num, int port, int bit, int dir, uchar value);
+#endif
board/bf609-ezkit/soft_switch.c +1 -10
index 2e1404f..e0c8d93 100644
@@ -12,14 +12,6 @@
 #include <i2c.h>
 #include "soft_switch.h"
 
-#define SWITCH_ADDR     0x21
-
-#define NUM_SWITCH      3
-#define IODIRA          0x0
-#define IODIRB          0x1
-#define OLATA           0x14
-#define OLATB           0x15
-
 struct switch_config {
        uchar dir0; /* IODIRA */
        uchar dir1; /* IODIRB */
@@ -126,9 +118,8 @@ static int setup_soft_switch(int addr, struct switch_config *config)
        return i2c_write(addr, IODIRB, 1, &config->dir1, 1);
 }
 
-int config_switch_bit(int num, int port, int bit, int dir, uchar value)
+int config_switch_bit(int addr, int port, int bit, int dir, uchar value)
 {
-       int addr = SWITCH_ADDR + num;
        int ret, data_reg, dir_reg;
        uchar tmp;
 
board/bf609-ezkit/soft_switch.h +17 -8
index 8da0e44..d147fe1 100644
@@ -6,8 +6,10 @@
  * Licensed under the GPL-2 or later.
  */
 
-#ifndef __SOFT_SWITCH_H__
-#define __SOFT_SWITCH_H__
+#ifndef __BOARD_SOFT_SWITCH_H__
+#define __BOARD_SOFT_SWITCH_H__
+
+#include <asm/soft_switch.h>
 
 /* switch 0 port A */
 #define CAN_EN                 0x1
@@ -61,11 +63,18 @@
 #define PD3_SPI0MOSI_EN        0x1
 #define PD4_SPI0CK_EN          0x2
 
-#define IO_PORT_A              0
-#define IO_PORT_B              1
-#define IO_PORT_INPUT          0
-#define IO_PORT_OUTPUT         1
+#ifdef CONFIG_BFIN_BOARD_VERSION_1_0
+#define SWITCH_ADDR     0x21
+#else
+#define SWITCH_ADDR     0x20
+#endif
+
+#define NUM_SWITCH      3
+#define IODIRA          0x0
+#define IODIRB          0x1
+#define OLATA           0x14
+#define OLATB           0x15
 
-int config_switch_bit(int num, int port, int bit, int dir, uchar value);
 int setup_board_switches(void);
-#endif
+
+#endif /* __BOARD_SOFT_SWITCH_H__ */
common/Makefile +1 -0
index 54fcc81..80fee78 100644
@@ -157,6 +157,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o
 COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o
 COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o
 COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o
+COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o
 COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o
 COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o
 COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.o
common/cmd_softswitch.c new file +41 -0
new file mode 100644
index 0000000..f75d926
@@ -0,0 +1,41 @@
+/*
+ * cmd_softswitch.c - set the softswitch for bf60x
+ *
+ * Copyright (c) 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/blackfin.h>
+#include <asm/soft_switch.h>
+
+int do_softswitch(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+       int switchaddr, value, pin, port;
+
+       if (argc != 5)
+               return CMD_RET_USAGE;
+
+       if (strcmp(argv[2], "GPA") == 0)
+               port = IO_PORT_A;
+       else if (strcmp(argv[2], "GPB") == 0)
+               port = IO_PORT_B;
+       else
+               return CMD_RET_USAGE;
+
+       switchaddr = simple_strtoul(argv[1], NULL, 16);
+       pin = simple_strtoul(argv[3], NULL, 16);
+       value = simple_strtoul(argv[4], NULL, 16);
+
+       config_switch_bit(switchaddr, port, (1 << pin), IO_PORT_OUTPUT, value);
+
+       return 0;
+}
+
+U_BOOT_CMD(
+       softswitch_output, 5, 1, do_softswitch,
+       "switchaddr GPA/GPB pin_offset value",
+       ""
+);
include/configs/bf609-ezkit.h +1 -1
index 8b90129..f0ac86b 100644
@@ -144,6 +144,7 @@
 #define CONFIG_UART_CONSOLE    0
 
 #define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_SOFTSWITCH
 
 #define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)
 #define CONFIG_BFIN_SOFT_SWITCH
--
Quoted 1 line

1.7.0.4

This is the patch that include "CONFIG_CMD_SOFTSWITCH". Is this what you think that I forgot to post before?

Regards,

Sonic

#3 lore raw

PATCH 2/2 blackfin: bf609: add softswitch config command

Quoted 186 lines · Sonic Zhang

Hi Tom

Quoted 182 lines · Sonic Zhang

From: Bob Liu <[email protected]>

Add softswitch_output command for bf609-ezkit to enable softswitches.

---
 arch/blackfin/include/asm/soft_switch.h |   18 +++++++++++++
 board/bf609-ezkit/soft_switch.c         |   11 +-------
 board/bf609-ezkit/soft_switch.h         |   25 +++++++++++++------
 common/Makefile                         |    1 +
 common/cmd_softswitch.c                 |   41 +++++++++++++++++++++++++++++++
 include/configs/bf609-ezkit.h           |    1 +
 6 files changed, 79 insertions(+), 18 deletions(-)
 create mode 100644 arch/blackfin/include/asm/soft_switch.h
 create mode 100644 common/cmd_softswitch.c
arch/blackfin/include/asm/soft_switch.h new file +18 -0
new file mode 100644
index 0000000..ff8e44d
@@ -0,0 +1,18 @@
+/*
+ * U-boot - main board file
+ *
+ * Copyright (c) 2008-2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#ifndef __SOFT_SWITCH_H__
+#define __SOFT_SWITCH_H__
+
+#define IO_PORT_A              0
+#define IO_PORT_B              1
+#define IO_PORT_INPUT          0
+#define IO_PORT_OUTPUT         1
+
+int config_switch_bit(int num, int port, int bit, int dir, uchar value);
+#endif
board/bf609-ezkit/soft_switch.c +1 -10
index 2e1404f..e0c8d93 100644
@@ -12,14 +12,6 @@
 #include <i2c.h>
 #include "soft_switch.h"
 
-#define SWITCH_ADDR     0x21
-
-#define NUM_SWITCH      3
-#define IODIRA          0x0
-#define IODIRB          0x1
-#define OLATA           0x14
-#define OLATB           0x15
-
 struct switch_config {
        uchar dir0; /* IODIRA */
        uchar dir1; /* IODIRB */
@@ -126,9 +118,8 @@ static int setup_soft_switch(int addr, struct switch_config *config)
        return i2c_write(addr, IODIRB, 1, &config->dir1, 1);
 }
 
-int config_switch_bit(int num, int port, int bit, int dir, uchar value)
+int config_switch_bit(int addr, int port, int bit, int dir, uchar value)
 {
-       int addr = SWITCH_ADDR + num;
        int ret, data_reg, dir_reg;
        uchar tmp;
 
board/bf609-ezkit/soft_switch.h +17 -8
index 8da0e44..d147fe1 100644
@@ -6,8 +6,10 @@
  * Licensed under the GPL-2 or later.
  */
 
-#ifndef __SOFT_SWITCH_H__
-#define __SOFT_SWITCH_H__
+#ifndef __BOARD_SOFT_SWITCH_H__
+#define __BOARD_SOFT_SWITCH_H__
+
+#include <asm/soft_switch.h>
 
 /* switch 0 port A */
 #define CAN_EN                 0x1
@@ -61,11 +63,18 @@
 #define PD3_SPI0MOSI_EN        0x1
 #define PD4_SPI0CK_EN          0x2
 
-#define IO_PORT_A              0
-#define IO_PORT_B              1
-#define IO_PORT_INPUT          0
-#define IO_PORT_OUTPUT         1
+#ifdef CONFIG_BFIN_BOARD_VERSION_1_0
+#define SWITCH_ADDR     0x21
+#else
+#define SWITCH_ADDR     0x20
+#endif
+
+#define NUM_SWITCH      3
+#define IODIRA          0x0
+#define IODIRB          0x1
+#define OLATA           0x14
+#define OLATB           0x15
 
-int config_switch_bit(int num, int port, int bit, int dir, uchar value);
 int setup_board_switches(void);
-#endif
+
+#endif /* __BOARD_SOFT_SWITCH_H__ */
common/Makefile +1 -0
index 54fcc81..80fee78 100644
@@ -157,6 +157,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o
 COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o
 COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o
 COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o
+COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o
 COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o
 COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o
 COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.o
common/cmd_softswitch.c new file +41 -0
new file mode 100644
index 0000000..f75d926
@@ -0,0 +1,41 @@
+/*
+ * cmd_softswitch.c - set the softswitch for bf60x
+ *
+ * Copyright (c) 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2 or later.
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/blackfin.h>
+#include <asm/soft_switch.h>
+
+int do_softswitch(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
+{
+       int switchaddr, value, pin, port;
+
+       if (argc != 5)
+               return CMD_RET_USAGE;
+
+       if (strcmp(argv[2], "GPA") == 0)
+               port = IO_PORT_A;
+       else if (strcmp(argv[2], "GPB") == 0)
+               port = IO_PORT_B;
+       else
+               return CMD_RET_USAGE;
+
+       switchaddr = simple_strtoul(argv[1], NULL, 16);
+       pin = simple_strtoul(argv[3], NULL, 16);
+       value = simple_strtoul(argv[4], NULL, 16);
+
+       config_switch_bit(switchaddr, port, (1 << pin), IO_PORT_OUTPUT, value);
+
+       return 0;
+}
+
+U_BOOT_CMD(
+       softswitch_output, 5, 1, do_softswitch,
+       "switchaddr GPA/GPB pin_offset value",
+       ""
+);
include/configs/bf609-ezkit.h +1 -0
index 8b90129..f0ac86b 100644
@@ -144,6 +144,7 @@
 #define CONFIG_UART_CONSOLE    0
 
 #define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_SOFTSWITCH
 
Quoted 7 lines
Quoted 4 lines
include/configs/bf609-ezkit.h +0 -1
 #define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)
 #define CONFIG_BFIN_SOFT_SWITCH
--

1.7.0.4

This is the patch that include "CONFIG_CMD_SOFTSWITCH". Is this what you think that I forgot to post before?

Yes, thanks. And it looks fine, aside from not updating the README.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 836 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130513/f16945e7/attachment.pgp>