blackfin: bf609: implement soft switch
PATCH 1/2 blackfin: bf609: implement soft switch
From: Sonic Zhang <[email protected]>
Set up soft switch pins properly in board init code.
--- board/bf609-ezkit/soft_switch.c | 180 +++++++++++++++++++++++++++++++++++++++ board/bf609-ezkit/soft_switch.h | 71 +++++++++++++++ 2 files changed, 251 insertions(+), 0 deletions(-) create mode 100644 board/bf609-ezkit/soft_switch.c create mode 100644 board/bf609-ezkit/soft_switch.h
board/bf609-ezkit/soft_switch.c new file +180 -0
@@ -0,0 +1,180 @@ +/* +* U-boot - main board file +* +* Copyright (c) 2008-2011 Analog Devices Inc. +* +* Licensed under the GPL-2 or later. +*/ + +#include <common.h> +#include <asm/blackfin.h> +#include <asm/io.h> +#include <i2c.h> +#include "soft_switch.h" + +#define SWITCH_ADDR 0x21 + +#define NUM_SWITCH 3 +#define IODIRA 0x0 +#define IODIRB 0x1 +#define OLATA 0x14 +#define OLATB 0x15 + +struct switch_config { +uchar dir0;/* IODIRA */ +uchar dir1;/* IODIRB */ +uchar value0;/* OLATA */ +uchar value1;/* OLATB */ +}; + +static struct switch_config switch_config_array[NUM_SWITCH ] = { + { +/* +U45 Port A U45 Port B + +7--------------- RMII_CLK_EN | 7--------------- ~TEMP_THERM_EN +| 6------------- ~CNT0ZM_EN | | 6------------- ~TEMP_IRQ_EN +| | 5----------- ~CNT0DG_EN | | | 5----------- ~UART0CTS_146_EN +| | | 4--------- ~CNT0UD_EN | | | | 4--------- ~UART0CTS_RST_EN +| | | | 3------- ~CAN0RX_EN | | | | | 3------- ~UART0CTS_RTS_LPBK +| | | | | 2----- ~CAN0_ERR_EN | | | | | | 2----- ~UART0CTS_EN +| | | | | | 1--- ~CAN_STB | | | | | | | 1--- ~UART0RX_EN +| | | | | | | 0- CAN_EN | | | | | | | | 0- ~UART0RTS_EN +| | | | | | | | | | | | | | | | | +O O O O O O O O | O O O O O O O O (I/O direction) +1 0 0 0 0 0 1 1 | 1 1 1 1 1 0 0 0 (value being set) +*/ + .dir0 =0x0 ,/* all output */ + .dir1 =0x0 ,/* all output */ + .value0 =RMII_CLK_EN |CAN_STB |CAN_EN , + .value1 =TEMP_THERM_EN |TEMP_IRQ_EN |UART0CTS_146_EN + |UART0CTS_RST_EN |UART0CTS_RTS_LPBK , + }, + { +/* +U46 Port A U46 Port B + +7--------------- ~LED4_GPIO_EN | 7--------------- EMPTY +| 6------------- ~LED3_GPIO_EN | | 6------------- ~SPI0D3_EN +| | 5----------- ~LED2_GPIO_EN | | | 5----------- ~SPI0D2_EN +| | | 4--------- ~LED1_GPIO_EN | | | | 4--------- ~SPIFLASH_CS_EN +| | | | 3------- SMC0_LP0_EN | | | | | 3------- ~SD_WP_EN +| | | | | 2----- EMPTY | | | | | | 2----- ~SD_CD_EN +| | | | | | 1--- SMC0_EPPI2 | | | | | | | 1--- ~PUSHBUTTON2_EN +_LP1_SWITCH +| | | | | | | 0- OVERRIDE_SMC0 | | | | | | | | 0- ~PUSHBUTTON1_EN +_LP0_BOOT +| | | | | | | | | | | | | | | | | +O O O O O O O O | O O O O O O O O (I/O direction) +0 0 0 0 0 X 0 1 | X 0 0 0 0 0 0 0 (value being set) +*/ + .dir0 =0x0 ,/* all output */ + .dir1 =0x0 ,/* all output */ +#ifdef CONFIG_BFIN_LINKPORT + .value0 =OVERRIDE_SMC0_LP0_BOOT , +#else + .value0 =SMC0_EPPI2_LP1_SWITCH , +#endif + .value1 =0x0 , + }, + { +/* +U47 Port A U47 Port B + +7--------------- ~PD2_SPI0MISO | 7--------------- EMPTY +_EI3_EN +| 6------------- ~PD1_SPI0D3 | | 6------------- EMPTY +_EPPI1D17 +_SPI0SEL2 +_EI3_EN +| | 5----------- ~PD0_SPI0D2 | | | 5----------- EMPTY +_EPPI1D16 +_SPI0SEL3 +_EI3_EN +| | | 4--------- ~WAKE_PUSH | | | | 4--------- EMPTY +BUTTON_EN +| | | | 3------- ~ETHERNET_EN | | | | | 3------- EMPTY +| | | | | 2----- PHYAD0 | | | | | | 2----- EMPTY +| | | | | | 1--- PHY_PWR | | | | | | | 1--- ~PD4_SPI0CK_EI3_EN +_DWN_INT +| | | | | | | 0- ~PHYINT_EN | | | | | | | | 0- ~PD3_SPI0MOSI_EI3_EN +| | | | | | | | | | | | | | | | | +O O O O O I I O | O O O O O O O O (I/O direction) +1 1 1 0 0 0 0 0 | X X X X X X 1 1 (value being set) +*/ + .dir0 =0x6 ,/* bits 1 and 2 input, all others output */ + .dir1 =0x0 ,/* all output */ + .value0 =PD1_SPI0D3_EN |PD0_SPI0D2_EN , + .value1 =0 , + }, +}; + +static int setup_soft_switch (int addr,struct switch_config *config) +{ +int ret =0 ; + + ret =i2c_write (addr,OLATA ,1 , &config->value0,1 ); +if (ret) +return ret; + ret =i2c_write (addr,OLATB ,1 , &config->value1,1 ); +if (ret) +return ret; + + ret =i2c_write (addr,IODIRA ,1 , &config->dir0,1 ); +if (ret) +return ret; +return i2c_write (addr,IODIRB ,1 , &config->dir1,1 ); +} + +int config_switch_bit (int num,int port,int bit,int dir,uchar value) +{ +int addr =SWITCH_ADDR + num; +int ret, data_reg, dir_reg; +uchar tmp; + +if (port ==IO_PORT_A ) { + data_reg =OLATA ; + dir_reg =IODIRA ; + }else { + data_reg =OLATB ; + dir_reg =IODIRB ; + } + +if (dir ==IO_PORT_INPUT ) { + ret =i2c_read (addr, dir_reg,1 , &tmp,1 ); +if (ret) +return ret; + tmp |= bit; +return i2c_write (addr, dir_reg,1 , &tmp,1 ); + }else { + ret =i2c_read (addr, data_reg,1 , &tmp,1 ); +if (ret) +return ret; +if (value) + tmp |= bit; +else + tmp &= ~bit; + ret =i2c_write (addr, data_reg,1 , &tmp,1 ); +if (ret) +return ret; + ret =i2c_read (addr, dir_reg,1 , &tmp,1 ); +if (ret) +return ret; + tmp &= ~bit; +return i2c_write (addr, dir_reg,1 , &tmp,1 ); + } +} + +int setup_board_switches (void ) +{ +int ret; +int i; + +for (i =0 ; i <NUM_SWITCH ; i++) { + ret =setup_soft_switch (SWITCH_ADDR + i, + &switch_config_array[i]); +if (ret) +return ret; + } +return 0 ; +}
board/bf609-ezkit/soft_switch.h new file +71 -0
71 lines not on this page · raw message
Signature · 1 line
1.7.0.4
PATCH 2/2 blackfin: bf609: add softswitch config command
From: Bob Liu <[email protected]>
Add softswitch_output command for bf609-ezkit to enable softswitches.
--- arch/blackfin/include/asm/soft_switch.h | 18 +++++++++++++ board/bf609-ezkit/soft_switch.c | 11 +------- board/bf609-ezkit/soft_switch.h | 25 +++++++++++++------ common/Makefile | 1 + common/cmd_softswitch.c | 41 +++++++++++++++++++++++++++++++ include/configs/bf609-ezkit.h | 1 + 6 files changed, 79 insertions(+), 18 deletions(-) create mode 100644 arch/blackfin/include/asm/soft_switch.h create mode 100644 common/cmd_softswitch.c
arch/blackfin/include/asm/soft_switch.h new file +18 -0
@@ -0,0 +1,18 @@ +/* +* U-boot - main board file +* +* Copyright (c) 2008-2012 Analog Devices Inc. +* +* Licensed under the GPL-2 or later. +*/ + +#ifndef __SOFT_SWITCH_H__ +#define __SOFT_SWITCH_H__ + +#define IO_PORT_A 0 +#define IO_PORT_B 1 +#define IO_PORT_INPUT 0 +#define IO_PORT_OUTPUT 1 + +int config_switch_bit (int num,int port,int bit,int dir,uchar value); +#endif
board/bf609-ezkit/soft_switch.c +1 -10
@@ -12,14 +12,6 @@#include <i2c.h> #include "soft_switch.h" -#define SWITCH_ADDR 0x21 - -#define NUM_SWITCH 3 -#define IODIRA 0x0 -#define IODIRB 0x1 -#define OLATA 0x14 -#define OLATB 0x15 -struct switch_config {uchar dir0;/* IODIRA */ uchar dir1;/* IODIRB */
@@ -126,9 +118,8 @@ static int setup_soft_switch(int addr, struct switch_config *config)return i2c_write (addr,IODIRB ,1 , &config->dir1,1 ); } -int config_switch_bit (int num,int port,int bit,int dir,uchar value) +int config_switch_bit (int addr,int port,int bit,int dir,uchar value) { -int addr =SWITCH_ADDR + num;int ret, data_reg, dir_reg;uchar tmp;
board/bf609-ezkit/soft_switch.h +17 -8
@@ -6,8 +6,10 @@* Licensed under the GPL-2 or later. */ -#ifndef __SOFT_SWITCH_H__ -#define __SOFT_SWITCH_H__ +#ifndef __BOARD_SOFT_SWITCH_H__ +#define __BOARD_SOFT_SWITCH_H__ + +#include <asm/soft_switch.h> /* switch 0 port A */ #define CAN_EN 0x1
@@ -61,11 +63,18 @@#define PD3_SPI0MOSI_EN 0x1#define PD4_SPI0CK_EN 0x2 -#define IO_PORT_A 0 -#define IO_PORT_B 1 -#define IO_PORT_INPUT 0 -#define IO_PORT_OUTPUT 1 +#ifdef CONFIG_BFIN_BOARD_VERSION_1_0 +#define SWITCH_ADDR 0x21 +#else +#define SWITCH_ADDR 0x20 +#endif + +#define NUM_SWITCH 3 +#define IODIRA 0x0 +#define IODIRB 0x1 +#define OLATA 0x14 +#define OLATB 0x15 -int config_switch_bit (int num,int port,int bit,int dir,uchar value);int setup_board_switches (void ); -#endif + +#endif /* __BOARD_SOFT_SWITCH_H__ */
common/Makefile +1 -0
@@ -157,6 +157,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o +COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.o
common/cmd_softswitch.c new file +41 -0
41 lines not on this page · raw message
include/configs/bf609-ezkit.h +1 -0
@@ -144,6 +144,7 @@#define CONFIG_UART_CONSOLE 0#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_SOFTSWITCH #define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)#define CONFIG_BFIN_SOFT_SWITCH
Signature · 1 line
1.7.0.4
PATCH 2/2 blackfin: bf609: add softswitch config command
Hi Tom
Quoted 185 lines · Sonic Zhang
From: Bob Liu <[email protected]>
Add
softswitch_outputcommand for bf609-ezkit to enable softswitches.Signed-off-by Bob Liu <[email protected]>Signed-off-by Sonic Zhang <[email protected]>--- arch/blackfin/include/asm/soft_switch.h | 18 +++++++++++++ board/bf609-ezkit/soft_switch.c | 11 +------- board/bf609-ezkit/soft_switch.h | 25 +++++++++++++------ common/Makefile | 1 + common/cmd_softswitch.c | 41 +++++++++++++++++++++++++++++++ include/configs/bf609-ezkit.h | 1 + 6 files changed, 79 insertions(+), 18 deletions(-) create mode 100644 arch/blackfin/include/asm/soft_switch.h create mode 100644 common/cmd_softswitch.carch/blackfin/include/asm/soft_switch.h new file +18
-0@@ -0,0 +1,18 @@ +/* +* U-boot - main board file +* +* Copyright (c) 2008-2012 Analog Devices Inc. +* +* Licensed under the GPL-2 or later. +*/ + +#ifndef __SOFT_SWITCH_H__ +#define __SOFT_SWITCH_H__ + +#define IO_PORT_A 0 +#define IO_PORT_B 1 +#define IO_PORT_INPUT 0 +#define IO_PORT_OUTPUT 1 + +int config_switch_bit (int num,int port,int bit,int dir,uchar value); +#endif board/bf609-ezkit/soft_switch.c +1
-10@@ -12,14 +12,6 @@#include <i2c.h> #include "soft_switch.h" -#define SWITCH_ADDR 0x21 - -#define NUM_SWITCH 3 -#define IODIRA 0x0 -#define IODIRB 0x1 -#define OLATA 0x14 -#define OLATB 0x15 -struct switch_config {uchar dir0;/* IODIRA */ uchar dir1;/* IODIRB */ @@ -126,9 +118,8 @@ static int setup_soft_switch(int addr, struct switch_config *config)return i2c_write (addr,IODIRB ,1 , &config->dir1,1 ); } -int config_switch_bit (int num,int port,int bit,int dir,uchar value) +int config_switch_bit (int addr,int port,int bit,int dir,uchar value) { -int addr =SWITCH_ADDR + num;int ret, data_reg, dir_reg;uchar tmp;board/bf609-ezkit/soft_switch.h +17
-8@@ -6,8 +6,10 @@* Licensed under the GPL-2 or later. */ -#ifndef __SOFT_SWITCH_H__ -#define __SOFT_SWITCH_H__ +#ifndef __BOARD_SOFT_SWITCH_H__ +#define __BOARD_SOFT_SWITCH_H__ + +#include <asm/soft_switch.h> /* switch 0 port A */ #define CAN_EN 0x1@@ -61,11 +63,18 @@#define PD3_SPI0MOSI_EN 0x1#define PD4_SPI0CK_EN 0x2 -#define IO_PORT_A 0 -#define IO_PORT_B 1 -#define IO_PORT_INPUT 0 -#define IO_PORT_OUTPUT 1 +#ifdef CONFIG_BFIN_BOARD_VERSION_1_0 +#define SWITCH_ADDR 0x21 +#else +#define SWITCH_ADDR 0x20 +#endif + +#define NUM_SWITCH 3 +#define IODIRA 0x0 +#define IODIRB 0x1 +#define OLATA 0x14 +#define OLATB 0x15 -int config_switch_bit (int num,int port,int bit,int dir,uchar value);int setup_board_switches (void ); -#endif + +#endif /* __BOARD_SOFT_SWITCH_H__ */ common/Makefile +1
-0@@ -157,6 +157,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o +COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.ocommon/cmd_softswitch.c new file +41
-0@@ -0,0 +1,41 @@ +/* +* cmd_softswitch.c - set the softswitch for bf60x +* +* Copyright (c) 2012 Analog Devices Inc. +* +* Licensed under the GPL-2 or later. +*/ + +#include <common.h> +#include <command.h> +#include <asm/blackfin.h> +#include <asm/soft_switch.h> + +int do_softswitch (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) +{ +int switchaddr, value, pin, port; + +if (argc !=5 ) +return CMD_RET_USAGE ; + +if (strcmp (argv[2 ],"GPA" ) ==0 ) + port =IO_PORT_A ; +else if (strcmp (argv[2 ],"GPB" ) ==0 ) + port =IO_PORT_B ; +else +return CMD_RET_USAGE ; + + switchaddr =simple_strtoul (argv[1 ],NULL ,16 ); + pin =simple_strtoul (argv[3 ],NULL ,16 ); + value =simple_strtoul (argv[4 ],NULL ,16 ); + +config_switch_bit (switchaddr, port, (1 << pin),IO_PORT_OUTPUT , value); + +return 0 ; +} + +U_BOOT_CMD ( + softswitch_output,5 ,1 , do_softswitch, +"switchaddr GPA/GPB pin_offset value" , +"" +);include/configs/bf609-ezkit.h +1
-1@@ -144,6 +144,7 @@#define CONFIG_UART_CONSOLE 0#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_SOFTSWITCH #define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)#define CONFIG_BFIN_SOFT_SWITCH --
Quoted 1 line
1.7.0.4
This is the patch that include "CONFIG_CMD_SOFTSWITCH". Is this what you think that I forgot to post before?
Regards,
Sonic
PATCH 2/2 blackfin: bf609: add softswitch config command
Quoted 186 lines · Sonic Zhang
Hi Tom
Quoted 182 lines · Sonic Zhang
From: Bob Liu <[email protected]>
Add
softswitch_outputcommand for bf609-ezkit to enable softswitches.Signed-off-by Bob Liu <[email protected]>Signed-off-by Sonic Zhang <[email protected]>--- arch/blackfin/include/asm/soft_switch.h | 18 +++++++++++++ board/bf609-ezkit/soft_switch.c | 11 +------- board/bf609-ezkit/soft_switch.h | 25 +++++++++++++------ common/Makefile | 1 + common/cmd_softswitch.c | 41 +++++++++++++++++++++++++++++++ include/configs/bf609-ezkit.h | 1 + 6 files changed, 79 insertions(+), 18 deletions(-) create mode 100644 arch/blackfin/include/asm/soft_switch.h create mode 100644 common/cmd_softswitch.carch/blackfin/include/asm/soft_switch.h new file +18
-0@@ -0,0 +1,18 @@ +/* +* U-boot - main board file +* +* Copyright (c) 2008-2012 Analog Devices Inc. +* +* Licensed under the GPL-2 or later. +*/ + +#ifndef __SOFT_SWITCH_H__ +#define __SOFT_SWITCH_H__ + +#define IO_PORT_A 0 +#define IO_PORT_B 1 +#define IO_PORT_INPUT 0 +#define IO_PORT_OUTPUT 1 + +int config_switch_bit (int num,int port,int bit,int dir,uchar value); +#endif board/bf609-ezkit/soft_switch.c +1
-10@@ -12,14 +12,6 @@#include <i2c.h> #include "soft_switch.h" -#define SWITCH_ADDR 0x21 - -#define NUM_SWITCH 3 -#define IODIRA 0x0 -#define IODIRB 0x1 -#define OLATA 0x14 -#define OLATB 0x15 -struct switch_config {uchar dir0;/* IODIRA */ uchar dir1;/* IODIRB */ @@ -126,9 +118,8 @@ static int setup_soft_switch(int addr, struct switch_config *config)return i2c_write (addr,IODIRB ,1 , &config->dir1,1 ); } -int config_switch_bit (int num,int port,int bit,int dir,uchar value) +int config_switch_bit (int addr,int port,int bit,int dir,uchar value) { -int addr =SWITCH_ADDR + num;int ret, data_reg, dir_reg;uchar tmp;board/bf609-ezkit/soft_switch.h +17
-8@@ -6,8 +6,10 @@* Licensed under the GPL-2 or later. */ -#ifndef __SOFT_SWITCH_H__ -#define __SOFT_SWITCH_H__ +#ifndef __BOARD_SOFT_SWITCH_H__ +#define __BOARD_SOFT_SWITCH_H__ + +#include <asm/soft_switch.h> /* switch 0 port A */ #define CAN_EN 0x1@@ -61,11 +63,18 @@#define PD3_SPI0MOSI_EN 0x1#define PD4_SPI0CK_EN 0x2 -#define IO_PORT_A 0 -#define IO_PORT_B 1 -#define IO_PORT_INPUT 0 -#define IO_PORT_OUTPUT 1 +#ifdef CONFIG_BFIN_BOARD_VERSION_1_0 +#define SWITCH_ADDR 0x21 +#else +#define SWITCH_ADDR 0x20 +#endif + +#define NUM_SWITCH 3 +#define IODIRA 0x0 +#define IODIRB 0x1 +#define OLATA 0x14 +#define OLATB 0x15 -int config_switch_bit (int num,int port,int bit,int dir,uchar value);int setup_board_switches (void ); -#endif + +#endif /* __BOARD_SOFT_SWITCH_H__ */ common/Makefile +1
-0@@ -157,6 +157,7 @@ COBJS-$(CONFIG_CMD_SF) += cmd_sf.o COBJS-$(CONFIG_CMD_SCSI) += cmd_scsi.o COBJS-$(CONFIG_CMD_SHA1SUM) += cmd_sha1sum.o COBJS-$(CONFIG_CMD_SETEXPR) += cmd_setexpr.o +COBJS-$(CONFIG_CMD_SOFTSWITCH) += cmd_softswitch.o COBJS-$(CONFIG_CMD_SPI) += cmd_spi.o COBJS-$(CONFIG_CMD_SPIBOOTLDR) += cmd_spibootldr.o COBJS-$(CONFIG_CMD_STRINGS) += cmd_strings.ocommon/cmd_softswitch.c new file +41
-0@@ -0,0 +1,41 @@ +/* +* cmd_softswitch.c - set the softswitch for bf60x +* +* Copyright (c) 2012 Analog Devices Inc. +* +* Licensed under the GPL-2 or later. +*/ + +#include <common.h> +#include <command.h> +#include <asm/blackfin.h> +#include <asm/soft_switch.h> + +int do_softswitch (cmd_tbl_t *cmdtp,int flag,int argc,char *const argv[]) +{ +int switchaddr, value, pin, port; + +if (argc !=5 ) +return CMD_RET_USAGE ; + +if (strcmp (argv[2 ],"GPA" ) ==0 ) + port =IO_PORT_A ; +else if (strcmp (argv[2 ],"GPB" ) ==0 ) + port =IO_PORT_B ; +else +return CMD_RET_USAGE ; + + switchaddr =simple_strtoul (argv[1 ],NULL ,16 ); + pin =simple_strtoul (argv[3 ],NULL ,16 ); + value =simple_strtoul (argv[4 ],NULL ,16 ); + +config_switch_bit (switchaddr, port, (1 << pin),IO_PORT_OUTPUT , value); + +return 0 ; +} + +U_BOOT_CMD ( + softswitch_output,5 ,1 , do_softswitch, +"switchaddr GPA/GPB pin_offset value" , +"" +);include/configs/bf609-ezkit.h +1
-0@@ -144,6 +144,7 @@#define CONFIG_UART_CONSOLE 0#define CONFIG_CMD_MEMORY +#define CONFIG_CMD_SOFTSWITCH
Quoted 7 lines
Quoted 4 lines
include/configs/bf609-ezkit.h +0
-1#define CONFIG_SYS_MEMTEST_END (CONFIG_STACKBASE - 20*1024*1024 + 4)#define CONFIG_BFIN_SOFT_SWITCH --1.7.0.4
This is the patch that include "
CONFIG_CMD_SOFTSWITCH". Is this what you think that I forgot to post before?
Yes, thanks. And it looks fine, aside from not updating the README.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130513/f16945e7/attachment.pgp>