arm: at91: dt: at91sam9x5: correct NAND pins comments
Subsystems (2)
PATCH 1/2 arm: at91: dt: at91sam9x5: correct NAND pins comments
Comments on NAND pins where inverted.
---
based on 3.9-rc2
arch/arm/boot/dts/at91sam9x5.dtsi | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)
arch/arm/boot/dts/at91sam9x5.dtsi +2 -2
@@ -238,8 +238,8 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */ - 3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + <3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1>; /* PD5 gpio RDY/BUSY pin pull_up */ }; };
Signature · 1 line
1.7.2.5
PATCH 2/2 arm: at91: dt: at91sam9x5: complete NAND pinctrl
There was only chip enable and readdy/busy pins for the nand controller. This add the rest of the pins.pinctrl_nand_16bits contains the specific muxes for 16 bits NANDs.
---
based on 3.9-rc2
arch/arm/boot/dts/at91sam9x5.dtsi | 28 ++++++++++++++++++++++++++-- 1 files changed, 26 insertions(+), 2 deletions(-)
arch/arm/boot/dts/at91sam9x5.dtsi +26 -2
@@ -238,8 +238,32 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ - 3 5 0x0 0x1>; /* PD5 gpio RDY/BUSY pin pull_up */ + <3 0 0x1 0x0 /* PD0 periph A Read Enable */ + 3 1 0x1 0x0 /* PD1 periph A Write Enable */ + 3 2 0x1 0x0 /* PD2 periph A Address Latch Enable */ + 3 3 0x1 0x0 /* PD3 periph A Command Latch Enable */ + 3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1 /* PD5 gpio RDY/BUSY pin pull_up */ + 3 6 0x1 0x0 /* PD6 periph A Data bit 0 */ + 3 7 0x1 0x0 /* PD7 periph A Data bit 1 */ + 3 8 0x1 0x0 /* PD8 periph A Data bit 2 */ + 3 9 0x1 0x0 /* PD9 periph A Data bit 3 */ + 3 10 0x1 0x0 /* PD10 periph A Data bit 4 */ + 3 11 0x1 0x0 /* PD11 periph A Data bit 5 */ + 3 12 0x1 0x0 /* PD12 periph A Data bit 6 */ + 3 13 0x1 0x0>; /* PD13 periph A Data bit 7 */ + }; + + pinctrl_nand_16bits: nand_16bits-0 { + atmel,pins = + <3 14 0x1 0x0 /* PD14 periph A Data bit 8 */ + 3 15 0x1 0x0 /* PD15 periph A Data bit 9 */ + 3 16 0x1 0x0 /* PD16 periph A Data bit 10 */ + 3 17 0x1 0x0 /* PD17 periph A Data bit 11 */ + 3 18 0x1 0x0 /* PD18 periph A Data bit 12 */ + 3 19 0x1 0x0 /* PD19 periph A Data bit 13 */ + 3 20 0x1 0x0 /* PD20 periph A Data bit 14 */ + 3 21 0x1 0x0>; /* PD21 periph A Data bit 15 */ }; };
Signature · 1 line
1.7.2.5
PATCH 1/2 arm: at91: dt: at91sam9x5: correct NAND pins comments
In reply to Richard GenoudQuoted 3 lines · Richard Genoud
Comments on NAND pins where inverted.
Signed-off-by Richard Genoud <[email protected]>
Best Regards,
J.
Quoted 24 lines
---
based on 3.9-rc2arch/arm/boot/dts/at91sam9x5.dtsi | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)arch/arm/boot/dts/at91sam9x5.dtsi +2
-2@@ -238,8 +238,8 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */ - 3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + <3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1>; /* PD5 gpio RDY/BUSY pin pull_up */ }; };Signature · 1 line
1.7.2.5
PATCH 1/2 arm: at91: dt: at91sam9x5: correct NAND pins comments
In reply to Richard GenoudOn 03/11/2013 03:12 PM, Richard Genoud :
Quoted 15 lines
Comments on NAND pins where inverted.
Signed-off-by Richard Genoud <[email protected]>---
based on 3.9-rc2arch/arm/boot/dts/at91sam9x5.dtsi | 4 ++-- 1 files changed, 2 insertions(+), 2 deletions(-)arch/arm/boot/dts/at91sam9x5.dtsi +0
-0
arch/arm/boot/dts/at91sam9x5.dtsi line 245
Quoted 10 lines
arch/arm/boot/dts/at91sam9x5.dtsi +2
-2@@ -238,8 +238,8 @@ nand { pinctrl_nand: nand-0 { atmel,pins = - <3 4 0x0 0x1 /* PD5 gpio RDY pin pull_up */ - 3 5 0x0 0x1>; /* PD4 gpio enable pin pull_up */ + <3 4 0x0 0x1 /* PD4 gpio Chip Enable pin pull_up */ + 3 5 0x0 0x1>; /* PD5 gpio RDY/BUSY pin pull_up */ }; };
Thanks, both queued in at91-3.9-fixes branch.
Best regards,
Signature · 1 line
Nicolas Ferre