USB: PHY: nop: Device tree support for 3.10
Subsystems (2)
cover USB: PHY: nop: Device tree support for 3.10
Hi Felipe,
These patches add device tree support as well as PHY resource handling (i.e. clock, reset, power) for the NOP transceiver driver.
Please add these patches before your patches that move/rename the drivers/usb/otg/nop-usb-xceiv.c file.
NOTE: The first patch that changes platform header must be common between you and Tony's OMAP tree. Maybe you guys can share an immutable branch?
cheers,
-roger
The following changes since commit f6161aa153581da4a3867a2d1a7caf4be19b6ec9:
Linux 3.9-rc2 (2013-03-10 16:54:19 -0700)
are available in the git repository at:
git://github.com/rogerq/linux.git usbhost-phy-next
Roger Quadros (8):
usb: phy: nop: Add some parameters to platform data
usb: phy: nop: use devm_kzalloc()
usb: phy: nop: Manage PHY clock
usb: phy: nop: Handle power supply regulator for the PHY
usb: phy: nop: Handle RESET for the PHY
usb: phy: nop: use new PHY API to register PHY
usb: phy: nop: Add device tree support and binding information
USB: phy: nop: Defer probe if device needs VCC/RESET
.../devicetree/bindings/usb/usb-nop-xceiv.txt | 34 +++++ drivers/usb/otg/nop-usb-xceiv.c | 143 +++++++++++++++++-- include/linux/usb/nop-usb-xceiv.h | 5 + 3 files changed, 167 insertions(+), 15 deletions(-) create mode 100644 Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
Signature · 1 line
1.7.4.1
PATCH 1/8 usb: phy: nop: Add some parameters to platform data
Add clk_rate parameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.
Also add 2 flags, needs_vcc and needs_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.
--- include/linux/usb/nop-usb-xceiv.h | 5 +++++ 1 files changed, 5 insertions(+), 0 deletions(-)
include/linux/usb/nop-usb-xceiv.h +5 -0
@@ -5,6 +5,11 @@struct nop_usb_xceiv_platform_data {enum usb_phy_type type; +unsigned long clk_rate; + +/* if set fails with -EPROBE_DEFER if can't get regulator */ +unsigned int needs_vcc:1 ; +unsigned int needs_reset:1 ; };#if defined(CONFIG_NOP_USB_XCEIV ) || (defined(CONFIG_NOP_USB_XCEIV_MODULE ) && defined(MODULE ))
Signature · 1 line
1.7.4.1
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 6 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.
Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 4 lines · Marc Kleine-Budde
Quoted 3 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.
Quoted 8 lines
Quoted 3 lines
Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
There can be a user in the non DT case as well. Consider the following example:
The power regulator that supplies VCC to the PHY device sits over the I2C bus. The NOP transceiver driver is built into the kernel but the regulator driver is built as a module.
During boot, the NOP transceiver driver's probe is called before the regulator can be probed. So regulator_get() will fail and if the platform doesn't set the needs_vcc flag, the driver will continue as normal and the PHY device won't work.
I know that beagleboard can benefit from this. The current workaround is to register the regulator before we register the PHY in the board file. With the needs_vcc flag, we don't need to have that limitation.
cheers,
-roger
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 9 lines · Roger Quadros
Quoted 8 lines · Marc Kleine-Budde
Quoted 6 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.
Quoted 6 lines
Quoted 4 lines
Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
There can be a user in the non DT case as well. Consider the following example:
I'm just saying, let the implementation up to a real user for the non DT case. Beagleboard is ARM and there's no point of implementing non DT fall backs for ARM, IMHO.
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 15 lines · Marc Kleine-Budde
Quoted 14 lines · Roger Quadros
Quoted 12 lines · Marc Kleine-Budde
Quoted 6 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
Quoted 6 lines
Quoted 1 line
There can be a user in the non DT case as well. Consider the following example:
I'm just saying, let the implementation up to a real user for the non DT case. Beagleboard is ARM and there's no point of implementing non DT fall backs for ARM, IMHO.
Why do you say so?
It doesn't depend on the CPU architecture. It depends on how the board designer wired the board. A non ARM platform could also face the same problem as beagle.
It is not a non DT fallback. I believe many are still using non DT boot and it needs to work at least till we move all functionality to purely DT.
cheers,
-roger
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 23 lines · Roger Quadros
Quoted 15 lines · Marc Kleine-Budde
Quoted 14 lines · Roger Quadros
Quoted 12 lines · Marc Kleine-Budde
Quoted 6 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
Quoted 6 lines
Quoted 1 line
There can be a user in the non DT case as well. Consider the following example:
I'm just saying, let the implementation up to a real user for the non DT case. Beagleboard is ARM and there's no point of implementing non DT fall backs for ARM, IMHO.
Quoted 4 lines
Why do you say so?
It doesn't depend on the CPU architecture. It depends on how the board designer wired the board. A non ARM platform could also face the same problem as beagle.
Using -EPROBE_DEFER ist the way to solve the problem.
Quoted 2 lines
It is not a non DT fallback. I believe many are still using non DT boot and it needs to work at least till we move all functionality to purely DT.
From my point of view, it makes no sense today to implement new features which have a fallback for the non-DT case, if there isn't a real user of this feature. So IMHO don't add needs_vcc and needs_reset flags to the pdata, just take the information from the DT. As soon as there is a non-DT user of this feature she/he can implement it or even better switch to DT.
just my 2¢,
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
_______________________________________________
devicetree-discuss mailing list devicetree-discuss-uLR06cmDAlY/[email protected]
https://lists.ozlabs.org/listinfo/devicetree-discuss
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 24 lines · Marc Kleine-Budde
Quoted 23 lines · Roger Quadros
Quoted 21 lines · Marc Kleine-Budde
Quoted 9 lines · Roger Quadros
Quoted 8 lines · Marc Kleine-Budde
Quoted 6 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.Quoted 6 lines
Quoted 4 lines
Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
There can be a user in the non DT case as well. Consider the following example:
I'm just saying, let the implementation up to a real user for the non DT case. Beagleboard is ARM and there's no point of implementing non DT fall backs for ARM, IMHO.
Quoted 6 lines
Quoted 4 lines
Why do you say so?
It doesn't depend on the CPU architecture. It depends on how the board designer wired the board. A non ARM platform could also face the same problem as beagle.
Using -EPROBE_DEFER ist the way to solve the problem.
did you mean isn't? If you did then what is the other option?
Quoted 10 lines
Quoted 3 lines
It is not a non DT fallback. I believe many are still using non DT boot and it needs to work at least till we move all functionality to purely DT.
From my point of view, it makes no sense today to implement new features which have a fallback for the non-DT case, if there isn't a real user of this feature. So IMHO don't add
needs_vccandneeds_resetflags to the pdata, just take the information from the DT. As soon as there is a non-DT user of this feature she/he can implement it or even better switch to DT.
Adding Peter to the loop. I faintly remember him mentioning this issue before for beagle. We really need the deferred probe mechanism or we need to resort to device registering order.
The first user for needs_vcc flag will be the beagleboard file. I just didn't implement it in this patch [1].
On second thoughts, since [1] does work on beagleboard without requiring the needs_vcc flag, I think we can just live without it.
Felipe, Peter, what do you think?
cheers,
-roger
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 25 lines · Roger Quadros
Quoted 24 lines · Marc Kleine-Budde
Quoted 23 lines · Roger Quadros
Quoted 21 lines · Marc Kleine-Budde
Quoted 9 lines · Roger Quadros
Quoted 8 lines · Marc Kleine-Budde
Quoted 6 lines · Roger Quadros
Add
clk_rateparameter to platform data. If supplied, the NOP phy driver will program the clock to that rate during probe.Also add 2 flags,
needs_vccandneeds_reset. If the flag is set and the regulator couldn't be found then the driver will bail out with -EPROBE_DEFER.Quoted 6 lines
Quoted 4 lines
Is there a platform which fills out pdata.needs_vcc and pdata.needs_reset? IMHO it makes no sense to add features for the non DT case, if there isn't any user for it.
There can be a user in the non DT case as well. Consider the following example:
I'm just saying, let the implementation up to a real user for the non DT case. Beagleboard is ARM and there's no point of implementing non DT fall backs for ARM, IMHO.
Quoted 8 lines
Quoted 6 lines
Quoted 4 lines
Why do you say so?
It doesn't depend on the CPU architecture. It depends on how the board designer wired the board. A non ARM platform could also face the same problem as beagle.
Using -EPROBE_DEFER ist the way to solve the problem.
did you mean isn't? If you did then what is the other option?
You're using -EPROBE_DEFER, that's all perfectly fine.
Quoted 10 lines
Quoted 9 lines
Quoted 2 lines
It is not a non DT fallback. I believe many are still using non DT boot and it needs to work at least till we move all functionality to purely DT.
From my point of view, it makes no sense today to implement new features which have a fallback for the non-DT case, if there isn't a real user of this feature. So IMHO don't add
needs_vccandneeds_resetflags to the pdata, just take the information from the DT. As soon as there is a non-DT user of this feature she/he can implement it or even better switch to DT.
Quoted 6 lines
Adding Peter to the loop. I faintly remember him mentioning this issue before for beagle. We really need the deferred probe mechanism or we need to resort to device registering order.
The first user for
needs_vccflag will be the beagleboard file. I just didn't implement it in this patch [1].
Okay, I wrongly assumed that there wouldn't be added any new features to the old non-DT board files.
Quoted 2 lines
On second thoughts, since [1] does work on beagleboard without requiring the
needs_vccflag, I think we can just live without it.
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
_______________________________________________
devicetree-discuss mailing list devicetree-discuss-uLR06cmDAlY/[email protected]
https://lists.ozlabs.org/listinfo/devicetree-discuss
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
In reply to Roger QuadrosQuoted 3 lines · Roger Quadros
Adding Peter to the loop. I faintly remember him mentioning this issue before for beagle. We really need the deferred probe mechanism or we need to resort to device registering order.
Yes, BeagleBoard is a good example. Long story short: we have external dependency and the correct way to handle that is via deferred probe.
As of now we are not ready to kill the legacy support but over time we should move as much as we can to DT only mode.
Quoted 5 lines
The first user for
needs_vccflag will be the beagleboard file. I just didn't implement it in this patch [1].On second thoughts, since [1] does work on beagleboard without requiring the
needs_vccflag, I think we can just live without it.
The BeagleBoard works because the bootloader happen to enable the PWM generator which is used as a GPIO for the external HUB enable port. As soon as the bootloader stops doing this we are going to be in trouble.
Quoted 8 lines
Felipe, Peter, what do you think?
cheers,
-roger
Signature · 1 line
Péter
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
Quoted 14 lines · Peter Ujfalusi
Quoted 3 lines · Roger Quadros
Adding Peter to the loop. I faintly remember him mentioning this issue before for beagle. We really need the deferred probe mechanism or we need to resort to device registering order.
Yes, BeagleBoard is a good example. Long story short: we have external dependency and the correct way to handle that is via deferred probe.
As of now we are not ready to kill the legacy support but over time we should move as much as we can to DT only mode.
Quoted 3 lines
The first user for
needs_vccflag will be the beagleboard file. I just didn't implement it in this patch [1].
Quoted 7 lines
Quoted 2 lines
On second thoughts, since [1] does work on beagleboard without requiring the
needs_vccflag, I think we can just live without it.The BeagleBoard works because the bootloader happen to enable the PWM generator which is used as a GPIO for the external HUB enable port. As soon as the bootloader stops doing this we are going to be in trouble.
Wasn't it the LED A out GPO from PMIC that is used to enable the HUB? Just cross checking so I haven't missed anything.
I will resend the board support patch for beagle implementing needs_vcc flag for the deferred probe mechanism. Thanks.
cheers,
-roger
Re: [PATCH 1/8] usb: phy: nop: Add some parameters to platform data
In reply to Peter UjfalusiQuoted 7 lines · Peter Ujfalusi
Quoted 3 lines · Roger Quadros
Adding Peter to the loop. I faintly remember him mentioning this issue before for beagle. We really need the deferred probe mechanism or we need to resort to device registering order.
Yes, BeagleBoard is a good example. Long story short: we have external dependency and the correct way to handle that is via deferred probe.
Sure.
Quoted 2 lines
As of now we are not ready to kill the legacy support but over time we should move as much as we can to DT only mode.
I was assuming you're already on DT only :)
Marc
Signature · 4 lines
Pengutronix e.K. | Marc Kleine-Budde | Industrial Linux Solutions | Phone: +49-231-2826-924 | Vertretung West/Dortmund | Fax: +49-5121-206917-5555 | Amtsgericht Hildesheim, HRA 2686 | http://www.pengutronix.de |
_______________________________________________
devicetree-discuss mailing list devicetree-discuss-uLR06cmDAlY/[email protected]
https://lists.ozlabs.org/listinfo/devicetree-discuss
PATCH 2/8 usb: phy: nop: use devm_kzalloc()
In reply to Roger QuadrosUse resource managed kzalloc.
--- drivers/usb/otg/nop-usb-xceiv.c | 17 +++++------------ 1 files changed, 5 insertions(+), 12 deletions(-)
drivers/usb/otg/nop-usb-xceiv.c +5 -12
@@ -100,15 +100,14 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)enum usb_phy_type type =USB_PHY_TYPE_USB2 ;int err; - nop =kzalloc (sizeof *nop,GFP_KERNEL ); + nop =devm_kzalloc (&pdev->dev,sizeof (*nop),GFP_KERNEL );if (!nop)return -ENOMEM ; - nop->phy.otg =kzalloc (sizeof *nop->phy.otg,GFP_KERNEL ); -if (!nop->phy.otg) { -kfree (nop); + nop->phy.otg =devm_kzalloc (&pdev->dev,sizeof (*nop->phy.otg), +GFP_KERNEL ); +if (!nop->phy.otg)return -ENOMEM ; - }if (pdata) type = pdata->type;
@@ -127,7 +126,7 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)if (err) {dev_err (&pdev->dev,"can't register transceiver, err: %d\n" , err); - goto exit; +return err; }platform_set_drvdata (pdev, nop);
@@ -135,10 +134,6 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)ATOMIC_INIT_NOTIFIER_HEAD (&nop->phy.notifier);return 0 ; -exit: -kfree (nop->phy.otg); -kfree (nop); -return err; }static int nop_usb_xceiv_remove (struct platform_device *pdev)
@@ -148,8 +143,6 @@ static int nop_usb_xceiv_remove(struct platform_device *pdev)usb_remove_phy (&nop->phy);platform_set_drvdata (pdev,NULL ); -kfree (nop->phy.otg); -kfree (nop);return 0 ; }
Signature · 1 line
1.7.4.1
PATCH 3/8 usb: phy: nop: Manage PHY clock
In reply to Roger QuadrosIf the PHY has a clock associated to it then manage the clock. We just enable the clock in .init() and disable it in .shutdown().
Add clk_rate parameter in platform data and configure the clock rate during probe if supplied.
--- drivers/usb/otg/nop-usb-xceiv.c | 54 ++++++++++++++++++++++++++++++++++++++- 1 files changed, 53 insertions(+), 1 deletions(-)
drivers/usb/otg/nop-usb-xceiv.c +53 -1
@@ -32,10 +32,12 @@#include <linux/usb/otg.h> #include <linux/usb/nop-usb-xceiv.h> #include <linux/slab.h> +#include <linux/clk.h> struct nop_usb_xceiv {struct usb_phy phy;struct device *dev; +struct clk *clk; };static struct platform_device *pd;
@@ -64,6 +66,24 @@ static int nop_set_suspend(struct usb_phy *x, int suspend)return 0 ; } +static int nop_init (struct usb_phy *phy) +{ +struct nop_usb_xceiv *nop =dev_get_drvdata (phy->dev); + +if (!IS_ERR (nop->clk)) +clk_enable (nop->clk); + +return 0 ; +} + +static void nop_shutdown (struct usb_phy *phy) +{ +struct nop_usb_xceiv *nop =dev_get_drvdata (phy->dev); + +if (!IS_ERR (nop->clk)) +clk_disable (nop->clk); +} +static int nop_set_peripheral (struct usb_otg *otg,struct usb_gadget *gadget) {if (!otg)
@@ -112,10 +132,34 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)if (pdata) type = pdata->type; + nop->clk =devm_clk_get (&pdev->dev,"main_clk" ); +if (IS_ERR (nop->clk)) { +dev_dbg (&pdev->dev,"Can't get phy clock: %ld\n" , +PTR_ERR (nop->clk)); + } + +if (!IS_ERR (nop->clk) && pdata && pdata->clk_rate) { + err =clk_set_rate (nop->clk, pdata->clk_rate); +if (err) { +dev_err (&pdev->dev,"Error setting clock rate\n" ); +return err; + } + } + +if (!IS_ERR (nop->clk)) { + err =clk_prepare (nop->clk); +if (err) { +dev_err (&pdev->dev,"Error preparing clock\n" ); +return err; + } + } + nop->dev = &pdev->dev; nop->phy.dev = nop->dev; nop->phy.label ="nop-xceiv" ; nop->phy.set_suspend = nop_set_suspend; + nop->phy.init = nop_init; + nop->phy.shutdown = nop_shutdown; nop->phy.state =OTG_STATE_UNDEFINED ; nop->phy.otg->phy = &nop->phy;
@@ -126,7 +170,7 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)if (err) {dev_err (&pdev->dev,"can't register transceiver, err: %d\n" , err); -return err; + goto err_add; }platform_set_drvdata (pdev, nop);
@@ -134,12 +178,20 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)ATOMIC_INIT_NOTIFIER_HEAD (&nop->phy.notifier);return 0 ; + +err_add: +if (!IS_ERR (nop->clk)) +clk_unprepare (nop->clk); +return err; }static int nop_usb_xceiv_remove (struct platform_device *pdev) {struct nop_usb_xceiv *nop =platform_get_drvdata (pdev); +if (!IS_ERR (nop->clk)) +clk_unprepare (nop->clk); +usb_remove_phy (&nop->phy);platform_set_drvdata (pdev,NULL );
Signature · 1 line
1.7.4.1
PATCH 4/8 usb: phy: nop: Handle power supply regulator for the PHY
In reply to Roger QuadrosWe use "vcc" as the supply name for the PHY's power supply. The power supply will be enabled during .init() and disabled during .shutdown()
--- drivers/usb/otg/nop-usb-xceiv.c | 18 ++++++++++++++++++ 1 files changed, 18 insertions(+), 0 deletions(-)
drivers/usb/otg/nop-usb-xceiv.c +18 -0
@@ -33,11 +33,13 @@#include <linux/usb/nop-usb-xceiv.h> #include <linux/slab.h> #include <linux/clk.h> +#include <linux/regulator/consumer.h> struct nop_usb_xceiv {struct usb_phy phy;struct device *dev;struct clk *clk; +struct regulator *vcc; };static struct platform_device *pd;
@@ -70,6 +72,11 @@ static int nop_init(struct usb_phy *phy) {struct nop_usb_xceiv *nop =dev_get_drvdata (phy->dev); +if (!IS_ERR (nop->vcc)) { +if (regulator_enable (nop->vcc)) +dev_err (phy->dev,"Failed to enable power\n" ); + } +if (!IS_ERR (nop->clk))clk_enable (nop->clk);
@@ -82,6 +89,11 @@ static void nop_shutdown(struct usb_phy *phy)if (!IS_ERR (nop->clk))clk_disable (nop->clk); + +if (!IS_ERR (nop->vcc)) { +if (regulator_disable (nop->vcc)) +dev_err (phy->dev,"Failed to disable power\n" ); + } }static int nop_set_peripheral (struct usb_otg *otg,struct usb_gadget *gadget)
@@ -154,6 +166,12 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev) } } + nop->vcc =devm_regulator_get (&pdev->dev,"vcc" ); +if (IS_ERR (nop->vcc)) { +dev_dbg (&pdev->dev,"Error getting vcc regulator: %ld\n" , +PTR_ERR (nop->vcc)); + } + nop->dev = &pdev->dev; nop->phy.dev = nop->dev; nop->phy.label ="nop-xceiv" ;
Signature · 1 line
1.7.4.1
PATCH 5/8 usb: phy: nop: Handle RESET for the PHY
In reply to Roger QuadrosWe expect the RESET line to be modeled as a regulator with supply name "reset". The regulator should be modeled such that enabling the regulator brings the PHY device out of RESET and disabling the regulator holds the device in RESET.
They PHY will be held in RESET in .shutdown() and brought out of RESET in .init().
--- drivers/usb/otg/nop-usb-xceiv.c | 19 +++++++++++++++++++ 1 files changed, 19 insertions(+), 0 deletions(-)
drivers/usb/otg/nop-usb-xceiv.c +19 -0
@@ -40,6 +40,7 @@ struct nop_usb_xceiv {struct device *dev;struct clk *clk;struct regulator *vcc; +struct regulator *reset; };static struct platform_device *pd;
@@ -80,6 +81,12 @@ static int nop_init(struct usb_phy *phy)if (!IS_ERR (nop->clk))clk_enable (nop->clk); +if (!IS_ERR (nop->reset)) { +/* De-assert RESET */ +if (regulator_enable (nop->reset)) +dev_err (phy->dev,"Failed to de-assert reset\n" ); + } +return 0 ; }
@@ -87,6 +94,12 @@ static void nop_shutdown(struct usb_phy *phy) {struct nop_usb_xceiv *nop =dev_get_drvdata (phy->dev); +if (!IS_ERR (nop->reset)) { +/* Assert RESET */ +if (regulator_disable (nop->reset)) +dev_err (phy->dev,"Failed to assert reset\n" ); + } +if (!IS_ERR (nop->clk))clk_disable (nop->clk);
@@ -172,6 +185,12 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev) PTR_ERR(nop->vcc)); } + nop->reset =devm_regulator_get (&pdev->dev,"reset" ); +if (IS_ERR (nop->reset)) { +dev_dbg (&pdev->dev,"Error getting reset regulator: %ld\n" , +PTR_ERR (nop->reset)); + } + nop->dev = &pdev->dev; nop->phy.dev = nop->dev; nop->phy.label ="nop-xceiv" ;
Signature · 1 line
1.7.4.1
PATCH 6/8 usb: phy: nop: use new PHY API to register PHY
In reply to Roger QuadrosWe would need to support multiple PHYs of the same type so use the new PHY API usb_add_phy_dev() to register the PHY.
--- drivers/usb/otg/nop-usb-xceiv.c | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-)
drivers/usb/otg/nop-usb-xceiv.c +2 -1
@@ -198,12 +198,13 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev) nop->phy.init = nop_init; nop->phy.shutdown = nop_shutdown; nop->phy.state =OTG_STATE_UNDEFINED ; + nop->phy.type = type; nop->phy.otg->phy = &nop->phy; nop->phy.otg->set_host = nop_set_host; nop->phy.otg->set_peripheral = nop_set_peripheral; - err =usb_add_phy (&nop->phy, type); + err =usb_add_phy_dev (&nop->phy);if (err) {dev_err (&pdev->dev,"can't register transceiver, err: %d\n" , err);
Signature · 1 line
1.7.4.1
PATCH 7/8 usb: phy: nop: Add device tree support and binding information
In reply to Roger QuadrosThe PHY clock, clock rate, VCC regulator and RESET regulator can now be provided via device tree.
--- .../devicetree/bindings/usb/usb-nop-xceiv.txt | 34 +++++++++++++++++++ drivers/usb/otg/nop-usb-xceiv.c | 35 +++++++++++++++---- 2 files changed, 61 insertions(+), 8 deletions(-) create mode 100644 Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt
Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt new file +34 -0
@@ -0,0 +1,34 @@ +USB NOP PHY + +Required properties: +- compatible: should be usb-nop-xceiv + +Optional properties: +- clocks: phandle to the PHY clock. Use as per Documentation/devicetree + /bindings/clock/clock-bindings.txt + This property is required if clock-frequency is specified. + +- clock-names: Should be "main_clk" + +- clock-frequency: the clock frequency (in Hz) that the PHY clock must + be configured to. + +- vcc-supply: phandle to the regulator that provides RESET to the PHY. + +- reset-supply: phandle to the regulator that provides power to the PHY. + +Example: + + hsusb1_phy { + compatible = "usb-nop-xceiv"; + clock-frequency = <19200000>; + clocks = <&osc 0>; + clock-names = "main_clk"; + vcc-supply = <&hsusb1_vcc_regulator>; + reset-supply = <&hsusb1_reset_regulator>; + }; + +hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator +and expects that clock to be configured to 19.2MHz by the NOP PHY driver. +hsusb1_vcc_regulator provides power to the PHY and hsusb1_reset_regulator +controls RESET.
drivers/usb/otg/nop-usb-xceiv.c +27 -8
@@ -34,13 +34,14 @@#include <linux/slab.h> #include <linux/clk.h> #include <linux/regulator/consumer.h> +#include <linux/of.h> struct nop_usb_xceiv { -struct usb_phy phy; -struct device *dev; -struct clk *clk; -struct regulator *vcc; -struct regulator *reset; +struct usb_phy phy; +struct device *dev; +struct clk *clk; +struct regulator *vcc; +struct regulator *reset; };static struct platform_device *pd;
@@ -140,10 +141,12 @@ static int nop_set_host(struct usb_otg *otg, struct usb_bus *host)static int nop_usb_xceiv_probe (struct platform_device *pdev) { +struct device *dev = &pdev->dev;struct nop_usb_xceiv_platform_data *pdata = pdev->dev.platform_data;struct nop_usb_xceiv *nop;enum usb_phy_type type =USB_PHY_TYPE_USB2 ;int err; +u32 clk_rate =0 ; nop =devm_kzalloc (&pdev->dev,sizeof (*nop),GFP_KERNEL );if (!nop)
@@ -154,8 +157,16 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)if (!nop->phy.otg)return -ENOMEM ; -if (pdata) +if (dev->of_node) { +struct device_node *node = dev->of_node; + +if (of_property_read_u32 (node,"clock-frequency" , &clk_rate)) + clk_rate =0 ; + + }else if (pdata) { type = pdata->type; + clk_rate = pdata->clk_rate; + } nop->clk =devm_clk_get (&pdev->dev,"main_clk" );if (IS_ERR (nop->clk)) {
@@ -163,8 +174,8 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev) PTR_ERR(nop->clk)); } -if (!IS_ERR (nop->clk) && pdata && pdata->clk_rate) { - err =clk_set_rate (nop->clk, pdata->clk_rate); +if (!IS_ERR (nop->clk) && clk_rate) { + err =clk_set_rate (nop->clk, clk_rate);if (err) {dev_err (&pdev->dev,"Error setting clock rate\n" );return err;
@@ -237,12 +248,20 @@ static int nop_usb_xceiv_remove(struct platform_device *pdev)return 0 ; } +static const struct of_device_id nop_xceiv_dt_ids[] = { + { .compatible ="usb-nop-xceiv" }, + { } +}; + +MODULE_DEVICE_TABLE (of, nop_xceiv_dt_ids); +static struct platform_driver nop_usb_xceiv_driver = { .probe = nop_usb_xceiv_probe, .remove = nop_usb_xceiv_remove, .driver = { .name ="nop_usb_xceiv" , .owner =THIS_MODULE , + .of_match_table =of_match_ptr (nop_xceiv_dt_ids), }, };
Signature · 1 line
1.7.4.1
PATCH 8/8 USB: phy: nop: Defer probe if device needs VCC/RESET
In reply to Roger QuadrosAdd 2 flags, needs_vcc and needs_reset to platform data. If the flag is set and the regulator couldn't be found then we bail out with -EPROBE_DEFER.
For device tree boot we depend on presensce of vcc-supply/ reset-supply properties to decide if we should bail out with -EPROBE_DEFER or just continue in case the regulator can't be found.
This is required for proper functionality in cases where the regulator is needed but is probed later than the PHY device.
--- drivers/usb/otg/nop-usb-xceiv.c | 11 +++++++++++ 1 files changed, 11 insertions(+), 0 deletions(-)
drivers/usb/otg/nop-usb-xceiv.c +11 -0
@@ -147,6 +147,8 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)enum usb_phy_type type =USB_PHY_TYPE_USB2 ;int err;u32 clk_rate =0 ; +bool needs_vcc = false; +bool needs_reset = false; nop =devm_kzalloc (&pdev->dev,sizeof (*nop),GFP_KERNEL );if (!nop)
@@ -163,9 +165,14 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)if (of_property_read_u32 (node,"clock-frequency" , &clk_rate)) clk_rate =0 ; + needs_vcc =of_property_read_bool (node,"vcc-supply" ); + needs_reset =of_property_read_bool (node,"reset-supply" ); + }else if (pdata) { type = pdata->type; clk_rate = pdata->clk_rate; + needs_vcc = pdata->needs_vcc; + needs_reset = pdata->needs_reset; } nop->clk =devm_clk_get (&pdev->dev,"main_clk" );
@@ -194,12 +201,16 @@ static int nop_usb_xceiv_probe(struct platform_device *pdev)if (IS_ERR (nop->vcc)) {dev_dbg (&pdev->dev,"Error getting vcc regulator: %ld\n" ,PTR_ERR (nop->vcc)); +if (needs_vcc) +return -EPROBE_DEFER ; } nop->reset =devm_regulator_get (&pdev->dev,"reset" );if (IS_ERR (nop->reset)) {dev_dbg (&pdev->dev,"Error getting reset regulator: %ld\n" ,PTR_ERR (nop->reset)); +if (needs_reset) +return -EPROBE_DEFER ; } nop->dev = &pdev->dev;
Signature · 1 line
1.7.4.1