Add initial support for Wandboard dual lite and solo.
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
From: Fabio Estevam <[email protected]>
Add initial support for Wandboard.
Wandboard is a development board that has two variants: one version based on mx6 dual lite and another one based on mx6 solo.
For details on the features of Wandboard, please refer to:
http://www.wandboard.org/
---
Changes since v2:
- Also added support to the mx6solo variant.
- Rebased against u-boot-imx
Changes since v1:
- Use get_ram_size
- Remove ARP_TIMEOUT
- Remove unneeded "1u"
MAINTAINERS | 1 + arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 3 + board/wandboard/Makefile | 29 ++++ board/wandboard/wandboard.c | 181 ++++++++++++++++++++++++ boards.cfg | 2 + include/configs/wandboard.h | 207 ++++++++++++++++++++++++++++ 6 files changed, 423 insertions(+) create mode 100644 board/wandboard/Makefile create mode 100644 board/wandboard/wandboard.c create mode 100644 include/configs/wandboard.h
MAINTAINERS +1 -0
@@ -664,6 +664,7 @@ Fabio Estevam <[email protected]> mx53smd i.MX53 mx6qsabresd i.MX6Q mx6qsabreauto i.MX6Q + wandboard i.MX6DL/S Daniel Gorsulowski <[email protected]>
arch/arm/include/asm/arch-mx6/mx6dl_pins.h +3 -0
@@ -50,6 +50,8 @@#define NO_MUX_I 0#define NO_PAD_I 0enum { +MX6_PAD_CSI0_DAT10__UART1_TXD =IOMUX_PAD (0x0360 ,0x004C ,3 ,0x0000 ,0 ,0 ), +MX6_PAD_CSI0_DAT11__UART1_RXD =IOMUX_PAD (0x0364 ,0x0050 ,3 ,0x08FC ,1 ,0 ),MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK =IOMUX_PAD (0x03B0 ,0x009C ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 =IOMUX_PAD (0x03B4 ,0x00A0 ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2 =IOMUX_PAD (0x03B8 ,0x00A4 ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),
@@ -90,6 +92,7 @@ enum {MX6_PAD_EIM_D27__UART2_RXD =IOMUX_PAD (0x0540 ,0x0170 ,4 ,0x0904 ,1 ,0 ),MX6_PAD_EIM_D28__I2C1_SDA =IOMUX_PAD (0x0544 ,0x0174 ,1 |IOMUX_CONFIG_SION ,0x086C ,1 ,0 ),MX6_PAD_EIM_D28__GPIO_3_28 =IOMUX_PAD (0x0544 ,0x0174 ,5 ,0x0000 ,0 ,0 ), +MX6_PAD_EIM_D29__GPIO_3_29 =IOMUX_PAD (0x0548 ,0x0178 ,5 ,0x0000 ,0 ,0 ),MX6_PAD_ENET_MDC__ENET_MDC =IOMUX_PAD (0x05B8 ,0x01E8 ,1 ,0x0000 ,0 ,0 ),MX6_PAD_ENET_MDIO__ENET_MDIO =IOMUX_PAD (0x05BC ,0x01EC ,1 ,0x0810 ,0 ,0 ), MX6_PAD_ENET_REF_CLK__ENET_TX_CLK = IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0),
board/wandboard/Makefile new file +29 -0
@@ -0,0 +1,29 @@ +# +# (C) Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := wandboard.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################
board/wandboard/wandboard.c new file +181 -0
181 lines not on this page · raw message
boards.cfg +2 -0
@@ -261,6 +261,8 @@ nitrogen6q arm armv7 nitrogen6x boundar nitrogen6q2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q,DDR_MB=2048 nitrogen6s arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 nitrogen6s1g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,SDRAM_MB=1024 +wandboard_dl arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024 +wandboard_solo arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 cm_t35 arm armv7 cm_t35 - omap3 omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3
include/configs/wandboard.h new file +207 -0
207 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
Quoted 291 lines · Fabio Estevam
From: Fabio Estevam <[email protected]>
Add initial support for Wandboard.
Wandboard is a development board that has two variants: one version based on mx6 dual lite and another one based on mx6 solo.
For details on the features of Wandboard, please refer to:
http://www.wandboard.org/Signed-off-by Fabio Estevam <[email protected]>---
Changes since v2:
- Also added support to the mx6solo variant.
- Rebased against u-boot-imxChanges since v1:
- Useget_ram_size
- RemoveARP_TIMEOUT
- Remove unneeded "1u"MAINTAINERS | 1 + arch/arm/include/asm/arch-mx6/mx6dl_pins.h | 3 + board/wandboard/Makefile | 29 ++++ board/wandboard/wandboard.c | 181 ++++++++++++++++++++++++ boards.cfg | 2 + include/configs/wandboard.h | 207 ++++++++++++++++++++++++++++ 6 files changed, 423 insertions(+) create mode 100644 board/wandboard/Makefile create mode 100644 board/wandboard/wandboard.c create mode 100644 include/configs/wandboard.hMAINTAINERS +1
-0@@ -664,6 +664,7 @@ Fabio Estevam <[email protected]> mx53smd i.MX53 mx6qsabresd i.MX6Q mx6qsabreauto i.MX6Q + wandboard i.MX6DL/S Daniel Gorsulowski <[email protected]>arch/arm/include/asm/arch-mx6/mx6dl_pins.h +3
-0@@ -50,6 +50,8 @@#define NO_MUX_I 0#define NO_PAD_I 0enum { +MX6_PAD_CSI0_DAT10__UART1_TXD =IOMUX_PAD (0x0360 ,0x004C ,3 ,0x0000 ,0 ,0 ), +MX6_PAD_CSI0_DAT11__UART1_RXD =IOMUX_PAD (0x0364 ,0x0050 ,3 ,0x08FC ,1 ,0 ),MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK =IOMUX_PAD (0x03B0 ,0x009C ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 =IOMUX_PAD (0x03B4 ,0x00A0 ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2 =IOMUX_PAD (0x03B8 ,0x00A4 ,0 ,0x0000 ,0 , PAD_CTL_DSE_120ohm),@@ -90,6 +92,7 @@ enum {MX6_PAD_EIM_D27__UART2_RXD =IOMUX_PAD (0x0540 ,0x0170 ,4 ,0x0904 ,1 ,0 ),MX6_PAD_EIM_D28__I2C1_SDA =IOMUX_PAD (0x0544 ,0x0174 ,1 |IOMUX_CONFIG_SION ,0x086C ,1 ,0 ),MX6_PAD_EIM_D28__GPIO_3_28 =IOMUX_PAD (0x0544 ,0x0174 ,5 ,0x0000 ,0 ,0 ), +MX6_PAD_EIM_D29__GPIO_3_29 =IOMUX_PAD (0x0548 ,0x0178 ,5 ,0x0000 ,0 ,0 ),MX6_PAD_ENET_MDC__ENET_MDC =IOMUX_PAD (0x05B8 ,0x01E8 ,1 ,0x0000 ,0 ,0 ),MX6_PAD_ENET_MDIO__ENET_MDIO =IOMUX_PAD (0x05BC ,0x01EC ,1 ,0x0810 ,0 ,0 ), MX6_PAD_ENET_REF_CLK__ENET_TX_CLK = IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0),board/wandboard/Makefile new file +29
-0@@ -0,0 +1,29 @@ +# +# (C) Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := wandboard.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +#########################################################################board/wandboard/wandboard.c new file +181
-0@@ -0,0 +1,181 @@ +/* +* Copyright (C) 2013 Freescale Semiconductor, Inc. +* +* Author: Fabio Estevam <[email protected]> +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +*/ + +#include <asm/arch/clock.h> +#include <asm/arch/iomux.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/io.h> +#include <asm/sizes.h> +#include <common.h> +#include <fsl_esdhc.h> +#include <mmc.h> +#include <miiphy.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR ; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define ETH_PHY_RESET IMX_GPIO_NR(3, 29) + +int dram_init (void ) +{ + gd->ram_size =CONFIG_DDR_MB *SZ_1M ; + +return 0 ; +} + +static iomux_v3_cfg_t const uart1_pads[] = { +MX6_PAD_CSI0_DAT10__UART1_TXD |MUX_PAD_CTRL (UART_PAD_CTRL ), +MX6_PAD_CSI0_DAT11__UART1_RXD |MUX_PAD_CTRL (UART_PAD_CTRL ), +}; + +static iomux_v3_cfg_t const usdhc3_pads[] = { +MX6_PAD_SD3_CLK__USDHC3_CLK |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +MX6_PAD_SD3_CMD__USDHC3_CMD |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +MX6_PAD_SD3_DAT0__USDHC3_DAT0 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +MX6_PAD_SD3_DAT1__USDHC3_DAT1 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +MX6_PAD_SD3_DAT2__USDHC3_DAT2 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +MX6_PAD_SD3_DAT3__USDHC3_DAT3 |MUX_PAD_CTRL (USDHC_PAD_CTRL ), +}; + +static iomux_v3_cfg_t const enet_pads[] = { +MX6_PAD_ENET_MDIO__ENET_MDIO |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_ENET_MDC__ENET_MDC |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_TXC__ENET_RGMII_TXC |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_ENET_REF_CLK__ENET_TX_CLK |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_RXC__ENET_RGMII_RXC |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 |MUX_PAD_CTRL (ENET_PAD_CTRL ), +MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL |MUX_PAD_CTRL (ENET_PAD_CTRL ), +/* AR8031 PHY Reset */ +MX6_PAD_EIM_D29__GPIO_3_29 |MUX_PAD_CTRL (NO_PAD_CTRL ), +}; + +static void setup_iomux_uart (void ) +{ +imx_iomux_v3_setup_multiple_pads (uart1_pads,ARRAY_SIZE (uart1_pads)); +} + +static void setup_iomux_enet (void ) +{ +imx_iomux_v3_setup_multiple_pads (enet_pads,ARRAY_SIZE (enet_pads)); + +/* Reset AR8031 PHY */ +gpio_direction_output (ETH_PHY_RESET ,0 ); +udelay (500 ); +gpio_set_value (ETH_PHY_RESET ,1 ); +} + +static struct fsl_esdhc_cfg usdhc_cfg[1 ] = { + {USDHC3_BASE_ADDR }, +}; + +int board_mmc_init (bd_t *bis) +{ +imx_iomux_v3_setup_multiple_pads (usdhc3_pads,ARRAY_SIZE (usdhc3_pads)); + + usdhc_cfg[0 ].sdhc_clk =mxc_get_clock (MXC_ESDHC3_CLK ); +return fsl_esdhc_initialize (bis, &usdhc_cfg[0 ]); +} + +static int mx6_rgmii_rework (struct phy_device *phydev) +{ +unsigned short val; + +/* To enable AR8031 ouput a 125MHz clk from CLK_25M */ +phy_write (phydev,MDIO_DEVAD_NONE ,0xd ,0x7 ); +phy_write (phydev,MDIO_DEVAD_NONE ,0xe ,0x8016 ); +phy_write (phydev,MDIO_DEVAD_NONE ,0xd ,0x4007 ); + + val =phy_read (phydev,MDIO_DEVAD_NONE ,0xe ); + val &=0xffe3 ; + val |=0x18 ; +phy_write (phydev,MDIO_DEVAD_NONE ,0xe , val); + +/* introduce tx clock delay */ +phy_write (phydev,MDIO_DEVAD_NONE ,0x1d ,0x5 ); + val =phy_read (phydev,MDIO_DEVAD_NONE ,0x1e ); + val |=0x0100 ; +phy_write (phydev,MDIO_DEVAD_NONE ,0x1e , val); + +return 0 ; +} + +int board_phy_config (struct phy_device *phydev) +{ +mx6_rgmii_rework (phydev); + +if (phydev->drv->config) + phydev->drv->config (phydev); + +return 0 ; +} + +int board_eth_init (bd_t *bis) +{ +int ret; + +setup_iomux_enet (); + + ret =cpu_eth_init (bis); +if (ret) +printf ("FEC MXC: %s:failed\n" , __func__); + +return 0 ; +} + +int board_early_init_f (void ) +{ +setup_iomux_uart (); +return 0 ; +} + +int board_init (void ) +{ +/* address of boot parameters */ + gd->bd->bi_boot_params =PHYS_SDRAM +0x100 ; + +return 0 ; +} + +u32 get_board_rev (void ) +{ +return 0x61011 ; +} + +int checkboard (void ) +{ +puts ("Board: Wandboard\n" ); + +return 0 ; +}boards.cfg +0
-0
boards.cfg nitrogen6q arm armv7 nitrogen6x boundar · line 264
Quoted 4 lines
boards.cfg +1
-0@@ -261,6 +261,8 @@ nitrogen6q arm armv7 nitrogen6x boundar nitrogen6q2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q,DDR_MB=2048 nitrogen6s arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 nitrogen6s1g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,SDRAM_MB=1024 +wandboard_dl arm armv7 wandboard - mx6
I'd use 'wandboard_dual' as this seems to be how they use it in marketing material.
wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024
Quoted 224 lines
boards.cfg +1
-0+wandboard_solo arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 cm_t35 arm armv7 cm_t35 - omap3 omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3include/configs/wandboard.h new file +207
-1@@ -0,0 +1,207 @@ +/* +* Copyright (C) 2013 Freescale Semiconductor, Inc. +* +* Configuration settings for the Wandboard. +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +*/ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#define CONFIG_MX6 +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define CONFIG_MACH_TYPE 4412 + +#include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_BASE + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* Command definition */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 1 + +#define CONFIG_PREBOOT "" + +#define CONFIG_LOADADDR 0x12000000 +#define CONFIG_SYS_TEXT_BASE 0x17800000 + +/* MMC Configuration */ +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 +#define CONFIG_SYS_FSL_USDHC_NUM 2 + +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION + +/* Ethernet Configuration */ +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 1 +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console=ttymxc0\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=imx6dl-wandboard.dtb\0" \ + "fdt_addr=0x11000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=2\0" \ + "mmcroot=/dev/mmcblk0p3 rootwait rw\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${uimage}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev};" \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END 0x10010000 +#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000 + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_SIZE (8 * 1024) + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_BOOTZ + +#ifndef CONFIG_SYS_DCACHE_OFF +#define CONFIG_CMD_CACHE +#endif + +#endif /* __CONFIG_H * */ --1.7.9.5
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Signature · 3 lines
Otavio Salvador O.S. Systems E-mail: otavio at ossystems.com.br http://www.ossystems.com.br Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
Quoted 2 lines · Otavio Salvador
I'd use '
wandboard_dual' as this seems to be how they use it in marketing material.
No, the SoC used is a mx6 "dual lite", not "dual".
mx6 variants are: quad, dual, dual-lite, solo, solo-lite.
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
Quoted 9 lines · Fabio Estevam
Quoted 2 lines · Otavio Salvador
I'd use '
wandboard_dual' as this seems to be how they use it in marketing material.No, the SoC used is a mx6 "dual lite", not "dual".
mx6 variants are: quad, dual, dual-lite, solo, solo-lite.
I agree but the board name is 'Wandboard Dual', see
http://wandboard.org/index.php/details
So I'd use their name as users will end looking for it.
--
Otavio Salvador O.S. Systems
E-mail: otavio at ossystems.com.br http://www.ossystems.com.br
Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
Quoted 4 lines · Otavio Salvador
I agree but the board name is 'Wandboard Dual', see
http://wandboard.org/index.php/detailsSo I'd use their name as users will end looking for it.
If you look at the second row it says the chip is dual-lite.
Dual and dual-lite are not pin-to-pin compatible.
I don't want to call a board in U-boot of 'dual' if it uses a 'dual-lite' processor.
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
Quoted 6 lines · Fabio Estevam
Quoted 3 lines · Otavio Salvador
I agree but the board name is 'Wandboard Dual', see
http://wandboard.org/index.php/details
Quoted 8 lines
Quoted 1 line
So I'd use their name as users will end looking for it.
If you look at the second row it says the chip is dual-lite.
Dual and dual-lite are not pin-to-pin compatible.
I don't want to call a board in U-boot of 'dual' if it uses a 'dual-lite' processor.
I understand your point but we use board names not directly linked to the SoC they use, we name mx28evk and not mx287evk; mx23evk, not mx233evk ... but ok.
Signature · 3 lines
Otavio Salvador O.S. Systems E-mail: otavio at ossystems.com.br http://www.ossystems.com.br Mobile: +55 53 9981-7854 http://projetos.ossystems.com.br
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
Quoted 3 lines · Otavio Salvador
I understand your point but we use board names not directly linked to the SoC they use, we name mx28evk and not mx287evk; mx23evk, not mx233evk ... but ok.
mx233 is still a mx23 processor.
mx287 is still a mx28 processor.
mx6q / mx6dual / mx6dual-lite / mx6solo and mx6solo-lite are different processors.
PATCH v3 1/1 Add initial support for Wandboard dual lite and solo.
In reply to Otavio SalvadorDear Otavio Salvador,
Quoted 7 lines · In message <CAP9ODKo5cX7zGbxugXWX=tyF_aDkYjbfyf99cUKzxo_e_RvRpg@mail.gmail.com>…
Quoted 6 lines · Fabio Estevam
Quoted 2 lines · Otavio Salvador
I'd use '
wandboard_dual' as this seems to be how they use it in marketing material.
Quoted 8 lines
Quoted 3 lines
No, the SoC used is a mx6 "dual lite", not "dual".
mx6 variants are: quad, dual, dual-lite, solo, solo-lite.
I agree but the board name is 'Wandboard Dual', see
http://wandboard.org/index.php/detailsSo I'd use their name as users will end looking for it.
But that would lead into unsolvable conflict if there should ever be a Wandboard with a dual (not a dual-lite) processor...
I agree with Fabio here.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de "The X11 source code style is ATROCIOUS and should not be used as a model." - Doug Gwyn