socfpga: Adding configuration for development kit
PATCH v6 1/1 socfpga: Adding configuration for development kit
Separating the configuration file for Virtual Target and real hardware Cyclone V development kit
---
Changes for v6:
- Re-shuffle the change list
Changes for v5:
- Added Reviewed-by: Pavel Machek
- Cc: Tom Rini
Changes for v4:
- Added change log for each revision change
Changes for v3:
- Fixed the long subject of the patch
Changes for v2:
- Fixed the word wrap issue within patch
--- include/configs/socfpga_cyclone5.h | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-)
include/configs/socfpga_cyclone5.h +21 -7
@@ -11,6 +11,8 @@/* * High level configuration */ +/* Virtual target or real hardware */ +#define CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_ARMV7 #define CONFIG_L2_OFF
@@ -21,11 +23,12 @@#define CONFIG_SINGLE_BOOTLOADER #define CONFIG_SOCFPGA +/* base address for .text section */ +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_SYS_TEXT_BASE 0x08000040 -#define V_NS16550_CLK 1000000 -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000040 +#endif #define CONFIG_SYS_LOAD_ADDR 0x7fc0/* Console I/O Buffer Size */
@@ -154,7 +157,7 @@/* SDRAM Bank #1 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000/* SDRAM memory size */ -#define PHYS_SDRAM_1_SIZE 0x80000000 +#define PHYS_SDRAM_1_SIZE 0x40000000#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE#define CONFIG_SYS_MEMTEST_START 0x00000000
@@ -170,8 +173,13 @@#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK#define CONFIG_CONS_INDEX 1#define CONFIG_SYS_NS16550_COM1 UART0_BASE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define V_NS16550_CLK 1000000 +#else +#define V_NS16550_CLK 100000000 +#endif +#define CONFIG_BAUDRATE 115200/* * FLASH
@@ -184,9 +192,15 @@/* This timer use eosc1 where the clock frequency is fixed * throughout any condition */ #define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS -/* reload value when timer count to zero */ #define TIMER_LOAD_VAL 0xFFFFFFFF +/* Timer info */ +#define CONFIG_SYS_HZ 1000 +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_TIMER_CLOCK_KHZ 25000 +#endif #define CONFIG_ENV_IS_NOWHERE
Signature · 1 line
1.7.9.5
PATCH v6 1/1 socfpga: Adding configuration for development kit
Hi!
Albert, Tom.... this patch has been here for a week, without any comments. As far as I can tell, it is pretty much perfect. Can we get any comments on it, or (better), get it applied?
If you excuse one extra newline at end of file, [PATCH v6 1/1] socfpga: Creating driver for Reset Manager is in good shape too, and applying it would be nice.
Thanks,
Pavel
Quoted 97 lines
Separating the configuration file for Virtual Target and real hardware Cyclone V development kit
Signed-off-by Chin Liang See <[email protected]>Reviewed-by Pavel Machek <[email protected]>Cc Wolfgang Denk <[email protected]>Cc Pavel Machek <[email protected]>Cc Dinh Nguyen <[email protected]>Cc Tom Rini <[email protected]>Cc Albert Aribaud <[email protected]>---
Changes for v6:
- Re-shuffle the change list
Changes for v5:
- Added Reviewed-by: Pavel Machek
- Cc: Tom Rini
Changes for v4:
- Added change log for each revision change
Changes for v3:
- Fixed the long subject of the patch
Changes for v2:
- Fixed the word wrap issue within patch--- include/configs/socfpga_cyclone5.h | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-)include/configs/socfpga_cyclone5.h +21
-7@@ -11,6 +11,8 @@/* * High level configuration */ +/* Virtual target or real hardware */ +#define CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_ARMV7 #define CONFIG_L2_OFF @@ -21,11 +23,12 @@#define CONFIG_SINGLE_BOOTLOADER #define CONFIG_SOCFPGA +/* base address for .text section */ +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_SYS_TEXT_BASE 0x08000040 -#define V_NS16550_CLK 1000000 -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000040 +#endif #define CONFIG_SYS_LOAD_ADDR 0x7fc0/* Console I/O Buffer Size */ @@ -154,7 +157,7 @@/* SDRAM Bank #1 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000/* SDRAM memory size */ -#define PHYS_SDRAM_1_SIZE 0x80000000 +#define PHYS_SDRAM_1_SIZE 0x40000000#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE#define CONFIG_SYS_MEMTEST_START 0x00000000@@ -170,8 +173,13 @@#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK#define CONFIG_CONS_INDEX 1#define CONFIG_SYS_NS16550_COM1 UART0_BASE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define V_NS16550_CLK 1000000 +#else +#define V_NS16550_CLK 100000000 +#endif +#define CONFIG_BAUDRATE 115200/* * FLASH @@ -184,9 +192,15 @@/* This timer use eosc1 where the clock frequency is fixed * throughout any condition */ #define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS -/* reload value when timer count to zero */ #define TIMER_LOAD_VAL 0xFFFFFFFF +/* Timer info */ +#define CONFIG_SYS_HZ 1000 +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_TIMER_CLOCK_KHZ 25000 +#endif #define CONFIG_ENV_IS_NOWHERE
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
[U-Boot] Albert/Tom -- could we get patch applied or some feedback (was Re: [PATCH v6 1/1] socfpga: Adding configuration for development kit)
Hi!
Quoted 3 lines
Albert, Tom.... this patch has been here for a week, without any comments. As far as I can tell, it is pretty much perfect. Can we get any comments on it, or (better), get it applied?
Another week passed, and nothing happens. Is there just slow holiday time, or are we doing something wrong?
Thanks,
Pavel
Quoted 106 lines
If you excuse one extra newline at end of file, [PATCH v6 1/1] socfpga: Creating driver for Reset Manager is in good shape too, and applying it would be nice.
Thanks,
PavelQuoted 97 lines
Separating the configuration file for Virtual Target and real hardware Cyclone V development kit
Signed-off-by Chin Liang See <[email protected]>Reviewed-by Pavel Machek <[email protected]>Cc Wolfgang Denk <[email protected]>Cc Pavel Machek <[email protected]>Cc Dinh Nguyen <[email protected]>Cc Tom Rini <[email protected]>Cc Albert Aribaud <[email protected]>---
Changes for v6:
- Re-shuffle the change list
Changes for v5:
- Added Reviewed-by: Pavel Machek
- Cc: Tom Rini
Changes for v4:
- Added change log for each revision change
Changes for v3:
- Fixed the long subject of the patch
Changes for v2:
- Fixed the word wrap issue within patch--- include/configs/socfpga_cyclone5.h | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-)include/configs/socfpga_cyclone5.h +21
-7@@ -11,6 +11,8 @@/* * High level configuration */ +/* Virtual target or real hardware */ +#define CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_ARMV7 #define CONFIG_L2_OFF @@ -21,11 +23,12 @@#define CONFIG_SINGLE_BOOTLOADER #define CONFIG_SOCFPGA +/* base address for .text section */ +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_SYS_TEXT_BASE 0x08000040 -#define V_NS16550_CLK 1000000 -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000040 +#endif #define CONFIG_SYS_LOAD_ADDR 0x7fc0/* Console I/O Buffer Size */ @@ -154,7 +157,7 @@/* SDRAM Bank #1 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000/* SDRAM memory size */ -#define PHYS_SDRAM_1_SIZE 0x80000000 +#define PHYS_SDRAM_1_SIZE 0x40000000#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE#define CONFIG_SYS_MEMTEST_START 0x00000000@@ -170,8 +173,13 @@#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK#define CONFIG_CONS_INDEX 1#define CONFIG_SYS_NS16550_COM1 UART0_BASE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define V_NS16550_CLK 1000000 +#else +#define V_NS16550_CLK 100000000 +#endif +#define CONFIG_BAUDRATE 115200/* * FLASH @@ -184,9 +192,15 @@/* This timer use eosc1 where the clock frequency is fixed * throughout any condition */ #define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS -/* reload value when timer count to zero */ #define TIMER_LOAD_VAL 0xFFFFFFFF +/* Timer info */ +#define CONFIG_SYS_HZ 1000 +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_TIMER_CLOCK_KHZ 25000 +#endif #define CONFIG_ENV_IS_NOWHERE
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
[U-Boot] Albert/Tom -- could we get patch applied or some feedback (was Re: [PATCH v6 1/1] socfpga: Adding configuration for development kit)
Quoted 8 lines · Pavel Machek
Hi!
Quoted 3 lines
Albert, Tom.... this patch has been here for a week, without any comments. As far as I can tell, it is pretty much perfect. Can we get any comments on it, or (better), get it applied?
Another week passed, and nothing happens. Is there just slow holiday time, or are we doing something wrong?
I believe Albert is on holiday right now and it needs to come in via his tree. Sorry/thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 836 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20130822/c9d74b86/attachment.pgp>
[U-Boot] Albert/Tom -- could we get patch applied or some feedback (was Re: [PATCH v6 1/1] socfpga: Adding configuration for development kit)
In reply to Pavel MachekHi guys,
Wonder any updates on this? We plan to send the new patches only once these existing patches are accepted. Appreciate for your helps again.
Chin Liang
Quoted 20 lines · ZY - pavel
Hi!
Quoted 3 lines
Albert, Tom.... this patch has been here for a week, without any comments. As far as I can tell, it is pretty much perfect. Can we get any comments on it, or (better), get it applied?
Another week passed, and nothing happens. Is there just slow holiday time, or are we doing something wrong?
Thanks,
PavelQuoted 8 lines
If you excuse one extra newline at end of file, [PATCH v6 1/1] socfpga: Creating driver for Reset Manager is in good shape too, and applying it would be nice.
Thanks,
Pavel
[U-Boot] Albert/Tom -- could we get patch applied or some feedback (was Re: [PATCH v6 1/1] socfpga: Adding configuration for development kit)
Hi!
Quoted 3 lines
Wonder any updates on this? We plan to send the new patches only once these existing patches are accepted. Appreciate for your helps again.
Albert seems to be back, perhaps he'll us how he wants us to proceed?
Thanks,
Pavel
Quoted 10 lines
Quoted 10 lines
Quoted 3 lines
Albert, Tom.... this patch has been here for a week, without any comments. As far as I can tell, it is pretty much perfect. Can we get any comments on it, or (better), get it applied?
Another week passed, and nothing happens. Is there just slow holiday time, or are we doing something wrong?
Quoted 3 lines
If you excuse one extra newline at end of file, [PATCH v6 1/1] socfpga: Creating driver for Reset Manager is in good shape too, and applying it would be nice.
Signature · 2 lines
(english) http://www.livejournal.com/~pavelmachek (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
[U-Boot] Albert/Tom -- could we get patch applied or some feedback (was Re: [PATCH v6 1/1] socfpga: Adding configuration for development kit)
Hi Pavel,
Quoted 7 lines · ZY - pavel
Hi!
Quoted 3 lines
Wonder any updates on this? We plan to send the new patches only once these existing patches are accepted. Appreciate for your helps again.
Albert seems to be back, perhaps he'll us how he wants us to proceed?
Yup, I saw his posting again. Hope we can hear from Albert soon on these patches. Thanks
Chin Liang
Quoted 15 lines
Thanks,
PavelQuoted 10 lines
Quoted 10 lines
Quoted 3 lines
Albert, Tom.... this patch has been here for a week, without any comments. As far as I can tell, it is pretty much perfect. Can we get any comments on it, or (better), get it applied?
Another week passed, and nothing happens. Is there just slow holiday time, or are we doing something wrong?
Quoted 3 lines
If you excuse one extra newline at end of file, [PATCH v6 1/1] socfpga: Creating driver for Reset Manager is in good shape too, and applying it would be nice.
PATCH v6 1/1 socfpga: Adding configuration for development kit
In reply to Chin Liang SeeHi Chin,
Quoted 87 lines · Chin Liang See
Separating the configuration file for Virtual Target and real hardware Cyclone V development kit
Signed-off-by Chin Liang See <[email protected]>Reviewed-by Pavel Machek <[email protected]>Cc Wolfgang Denk <[email protected]>Cc Pavel Machek <[email protected]>Cc Dinh Nguyen <[email protected]>Cc Tom Rini <[email protected]>Cc Albert Aribaud <[email protected]>---
Changes for v6:
- Re-shuffle the change list
Changes for v5:
- Added Reviewed-by: Pavel Machek
- Cc: Tom Rini
Changes for v4:
- Added change log for each revision change
Changes for v3:
- Fixed the long subject of the patch
Changes for v2:
- Fixed the word wrap issue within patch--- include/configs/socfpga_cyclone5.h | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-)include/configs/socfpga_cyclone5.h +14
-7@@ -11,6 +11,8 @@/* * High level configuration */ +/* Virtual target or real hardware */ +#define CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_ARMV7 #define CONFIG_L2_OFF @@ -21,11 +23,12 @@#define CONFIG_SINGLE_BOOTLOADER #define CONFIG_SOCFPGA +/* base address for .text section */ +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET #define CONFIG_SYS_TEXT_BASE 0x08000040 -#define V_NS16550_CLK 1000000 -#define CONFIG_BAUDRATE 57600 -#define CONFIG_SYS_HZ 1000 -#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_SYS_TEXT_BASE 0x01000040 +#endif #define CONFIG_SYS_LOAD_ADDR 0x7fc0/* Console I/O Buffer Size */ @@ -154,7 +157,7 @@/* SDRAM Bank #1 */ #define CONFIG_SYS_SDRAM_BASE 0x00000000/* SDRAM memory size */ -#define PHYS_SDRAM_1_SIZE 0x80000000 +#define PHYS_SDRAM_1_SIZE 0x40000000#define PHYS_SDRAM_1 CONFIG_SYS_SDRAM_BASE#define CONFIG_SYS_MEMTEST_START 0x00000000@@ -170,8 +173,13 @@#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK#define CONFIG_CONS_INDEX 1#define CONFIG_SYS_NS16550_COM1 UART0_BASE -#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, 115200} +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define V_NS16550_CLK 1000000 +#else +#define V_NS16550_CLK 100000000 +#endif +#define CONFIG_BAUDRATE 115200/* * FLASH @@ -184,9 +192,15 @@/* This timer use eosc1 where the clock frequency is fixed * throughout any condition */ #define CONFIG_SYS_TIMERBASE SOCFPGA_OSC1TIMER0_ADDRESS -/* reload value when timer count to zero */ #define TIMER_LOAD_VAL 0xFFFFFFFF
include/configs/socfpga_cyclone5.h line 206
Quoted 10 lines
include/configs/socfpga_cyclone5.h +7
-0+/* Timer info */ +#define CONFIG_SYS_HZ 1000 +#ifdef CONFIG_SOCFPGA_VIRTUAL_TARGET +#define CONFIG_TIMER_CLOCK_KHZ 2400 +#else +#define CONFIG_TIMER_CLOCK_KHZ 25000 +#endif #define CONFIG_ENV_IS_NOWHERE
Applied to u-boot-arm/master, thanks!
Amicalement,
Signature · 1 line
Albert.