ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
Subsystems (7)
PATCH v2 1/6 ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
We must clear this IMX6Q_GPR13_SATA_MPLL_CLK_EN bit on i.MX6Q, otherwise Linux will fail to find the attached drive on some boards.
This entire fix was:
--- drivers/ata/ahci_imx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
V2: Update the value in the comment from 0x7ffffffd to 0x7ffffffe
drivers/ata/ahci_imx.c +2 -1
@@ -113,7 +113,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)/* * set PHY Paremeters, two steps to configure the GPR13, * one write for rest of parameters, mask of first write -* is 0x07fffffd, and the other one write for setting +* is 0x07fffffe, and the other one write for setting * the mpll_clk_en. */ regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK
@@ -125,6 +125,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio) | IMX6Q_GPR13_SATA_TX_BOOST_MASK |IMX6Q_GPR13_SATA_TX_LVL_MASK |IMX6Q_GPR13_SATA_TX_EDGE_RATE + |IMX6Q_GPR13_SATA_MPLL_CLK_EN ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
Signature · 1 line
1.8.4.2
PATCH v5 2/6 ahci: imx: Pull out the clock enable/disable calls
The same code for enabling and disabling SATA clock was found in multiple places in the driver. Implement functions that enable/disable the SATA clock and use them in such places instead of duplicating the code.
--- drivers/ata/ahci_imx.c | 143 ++++++++++++++++++++++++++----------------------- 1 file changed, 75 insertions(+), 68 deletions(-)
V2: Move the OR sign from the begining of the line to the end of the line in
the regmap_update_bits() call.
V3: Move the PHY configuration programming out of the clock_enable function
and into the probe() function.
V4: Rebase on top of new 1/6 patch.
Remove clk_prepare_enable() being called twice in imx_sata_clock_enable() since it was a rebase artifact.
V5: Pull out the usleep_range() into imx_sata_clock_enable() as well as a small
delay is needed after turning on the clock. Also rebase this on top of the change in comment in 1/6 .
drivers/ata/ahci_imx.c +75 -68
@@ -47,6 +47,36 @@ static int ahci_imx_hotplug;module_param_named (hotplug, ahci_imx_hotplug, int,0644 );MODULE_PARM_DESC (hotplug,"AHCI IMX hot-plug support (0=Don't support, 1=support)" ); +static int imx_sata_clock_enable (struct device *dev) +{ +struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); +int ret; + + ret =clk_prepare_enable (imxpriv->sata_ref_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); +return ret; + } + +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN ); + +usleep_range (1000 ,2000 ); + +return 0 ; +} + +static void imx_sata_clock_disable (struct device *dev) +{ +struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); + +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , + !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +clk_disable_unprepare (imxpriv->sata_ref_clk); +} +static void ahci_imx_error_handler (struct ata_port *ap) {u32 reg_val;
@@ -72,10 +102,7 @@ static void ahci_imx_error_handler(struct ata_port *ap)*/ reg_val =readl (mmio +PORT_PHY_CTL );writel (reg_val |PORT_PHY_CTL_PDDQ_LOC , mmio +PORT_PHY_CTL ); -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); +imx_sata_clock_disable (ap->dev); imxpriv->no_device = true; }
@@ -97,46 +124,9 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)unsigned int reg_val;struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); - imxpriv->gpr = -syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); -if (IS_ERR (imxpriv->gpr)) { -dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); -return PTR_ERR (imxpriv->gpr); - } - - ret =clk_prepare_enable (imxpriv->sata_ref_clk); -if (ret <0 ) { -dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); + ret =imx_sata_clock_enable (dev); +if (ret <0 )return ret; - } - -/* -* set PHY Paremeters, two steps to configure the GPR13, -* one write for rest of parameters, mask of first write -* is 0x07fffffe, and the other one write for setting -* the mpll_clk_en. -*/ -regmap_update_bits (imxpriv->gpr,0x34 ,IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK - |IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK - |IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK - |IMX6Q_GPR13_SATA_SPD_MODE_MASK - |IMX6Q_GPR13_SATA_MPLL_SS_EN - |IMX6Q_GPR13_SATA_TX_ATTEN_MASK - |IMX6Q_GPR13_SATA_TX_BOOST_MASK - |IMX6Q_GPR13_SATA_TX_LVL_MASK - |IMX6Q_GPR13_SATA_TX_EDGE_RATE - |IMX6Q_GPR13_SATA_MPLL_CLK_EN - ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB - |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M - |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F - |IMX6Q_GPR13_SATA_SPD_MODE_3P0G - |IMX6Q_GPR13_SATA_MPLL_SS_EN - |IMX6Q_GPR13_SATA_TX_ATTEN_9_16 - |IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB - |IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); -regmap_update_bits (imxpriv->gpr,0x34 ,IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -usleep_range (100 ,200 );/* * Configure the HWINIT bits of the HOST_CAP and HOST_PORTS_IMPL,
@@ -164,11 +154,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)static void imx6q_sata_exit (struct device *dev) { -struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); - -regmap_update_bits (imxpriv->gpr,0x34 ,IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); +imx_sata_clock_disable (dev); }static int imx_ahci_suspend (struct device *dev)
@@ -179,12 +165,8 @@ static int imx_ahci_suspend(struct device *dev)* If no_device is set, The CLKs had been gated off in the * initialization so don't do it again here. */ -if (!imxpriv->no_device) { -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -clk_disable_unprepare (imxpriv->sata_ref_clk); - } +if (!imxpriv->no_device) +imx_sata_clock_disable (dev);return 0 ; }
@@ -192,22 +174,12 @@ static int imx_ahci_suspend(struct device *dev)static int imx_ahci_resume (struct device *dev) {struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); -int ret; +int ret =0 ; -if (!imxpriv->no_device) { - ret =clk_prepare_enable (imxpriv->sata_ref_clk); -if (ret <0 ) { -dev_err (dev,"pre-enable sata_ref clock err:%d\n" , ret); -return ret; - } - -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_MPLL_CLK_EN ); -usleep_range (1000 ,2000 ); - } +if (!imxpriv->no_device) + ret =imx_sata_clock_enable (dev); -return 0 ; +return ret; }static struct ahci_platform_data imx6q_sata_pdata = {
@@ -290,6 +262,41 @@ static int imx_ahci_probe(struct platform_device *pdev) ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask; ahci_dev->of_node = dev->of_node; + imxpriv->gpr = +syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); + +if (IS_ERR (imxpriv->gpr)) { +dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); + ret =PTR_ERR (imxpriv->gpr); + goto err_out; + } + +/* +* Set PHY Paremeters, two steps to configure the GPR13, +* one write for rest of parameters, mask of first write +* is 0x07fffffe, and the other one write for setting +* the mpll_clk_en happens in imx_sata_clock_enable(). +*/ +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK | +IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK | +IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK | +IMX6Q_GPR13_SATA_SPD_MODE_MASK | +IMX6Q_GPR13_SATA_MPLL_SS_EN | +IMX6Q_GPR13_SATA_TX_ATTEN_MASK | +IMX6Q_GPR13_SATA_TX_BOOST_MASK | +IMX6Q_GPR13_SATA_TX_LVL_MASK | +IMX6Q_GPR13_SATA_TX_EDGE_RATE | +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB | +IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M | +IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F | +IMX6Q_GPR13_SATA_SPD_MODE_3P0G | +IMX6Q_GPR13_SATA_MPLL_SS_EN | +IMX6Q_GPR13_SATA_TX_ATTEN_9_16 | +IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB | +IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); + ret =platform_device_add_resources (ahci_pdev, res,2 );if (ret) goto err_out;
Signature · 1 line
1.8.4.2
PATCH v5 3/6 ahci: imx: Add i.MX53 support
In reply to Marek VasutAdd minor adjustments to support i.MX53 SATA port as well as i.MX6Q one. The difference here is mostly the clock which need to be enabled and also the lack of need of programming IOMUXC registers on i.MX53. All of which is well handles in the clock enable/disable functions. Note that this patch also cleans up the names of the common functions, so they don't read imx6q_* but imx_* instead.
--- drivers/ata/ahci_imx.c | 164 ++++++++++++++++++++++++++++++++----------------- 1 file changed, 106 insertions(+), 58 deletions(-)
V2: Rebase this patch to be coherent with formating change in 1/5 .
V3: Rebase this patch to be coherent with change in 1/5 .
V4: Use sata_ref_clk for both MX53 and MX6 instead of separate sata_phy_clk
for MX53.
V5: Rebase on top of changes in 1/6 and 2/6 . Note that I am keeping the small
delay after enabling clock on MX53 as well.
drivers/ata/ahci_imx.c +106 -58
@@ -34,10 +34,21 @@ enum { HOST_TIMER1MS = 0xe0, /* Timer 1-ms */ }; +enum ahci_imx_type { +AHCI_IMX53 , +AHCI_IMX6Q , +}; +struct imx_ahci_priv {struct platform_device *ahci_pdev; +enum ahci_imx_type type; + +/* i.MX53 clock */ +struct clk *sata_gate_clk; +/* Common clock */ struct clk *sata_ref_clk;struct clk *ahb_clk; +struct regmap *gpr;bool no_device;bool first_time;
@@ -52,29 +63,52 @@ static int imx_sata_clock_enable(struct device *dev)struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent);int ret; +if (imxpriv->type ==AHCI_IMX53 ) { + ret =clk_prepare_enable (imxpriv->sata_gate_clk); +if (ret <0 ) { +dev_err (dev,"prepare-enable sata_gate clock err:%d\n" , + ret); +return ret; + } + } + ret =clk_prepare_enable (imxpriv->sata_ref_clk);if (ret <0 ) { -dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , ret); -return ret; +dev_err (dev,"prepare-enable sata_ref clock err:%d\n" , + ret); + goto clk_err; } -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +if (imxpriv->type ==AHCI_IMX6Q ) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_MPLL_CLK_EN ); + }usleep_range (1000 ,2000 );return 0 ; + +clk_err: +if (imxpriv->type ==AHCI_IMX53 ) +clk_disable_unprepare (imxpriv->sata_gate_clk); +return ret; }static void imx_sata_clock_disable (struct device *dev) {struct imx_ahci_priv *imxpriv =dev_get_drvdata (dev->parent); -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_MPLL_CLK_EN , - !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); +if (imxpriv->type ==AHCI_IMX6Q ) { +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_MPLL_CLK_EN , + !IMX6Q_GPR13_SATA_MPLL_CLK_EN ); + } +clk_disable_unprepare (imxpriv->sata_ref_clk); + +if (imxpriv->type ==AHCI_IMX53 ) +clk_disable_unprepare (imxpriv->sata_gate_clk); }static void ahci_imx_error_handler (struct ata_port *ap)
@@ -118,7 +152,7 @@ static const struct ata_port_info ahci_imx_port_info = { .port_ops = &ahci_imx_ops, }; -static int imx6q_sata_init (struct device *dev,void __iomem *mmio) +static int imx_sata_init (struct device *dev,void __iomem *mmio) {int ret =0 ;unsigned int reg_val;
@@ -152,7 +186,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)return 0 ; } -static void imx6q_sata_exit (struct device *dev) +static void imx_sata_exit (struct device *dev) {imx_sata_clock_disable (dev); }
@@ -182,16 +216,18 @@ static int imx_ahci_resume(struct device *dev)return ret; } -static struct ahci_platform_data imx6q_sata_pdata = { - .init = imx6q_sata_init, - .exit = imx6q_sata_exit, - .ata_port_info = &ahci_imx_port_info, - .suspend = imx_ahci_suspend, - .resume = imx_ahci_resume, +static struct ahci_platform_data imx_sata_pdata = { + .init = imx_sata_init, + .exit = imx_sata_exit, + .ata_port_info = &ahci_imx_port_info, + .suspend = imx_ahci_suspend, + .resume = imx_ahci_resume, + };static const struct of_device_id imx_ahci_of_match[] = { - { .compatible ="fsl,imx6q-ahci" , .data = &imx6q_sata_pdata}, + { .compatible ="fsl,imx53-ahci" , .data = (void *)AHCI_IMX53 }, + { .compatible ="fsl,imx6q-ahci" , .data = (void *)AHCI_IMX6Q }, {}, };MODULE_DEVICE_TABLE (of, imx_ahci_of_match);
@@ -201,12 +237,20 @@ static int imx_ahci_probe(struct platform_device *pdev)struct device *dev = &pdev->dev;struct resource *mem, *irq, res[2 ];const struct of_device_id *of_id; +enum ahci_imx_type type;const struct ahci_platform_data *pdata =NULL ;struct imx_ahci_priv *imxpriv;struct device *ahci_dev;struct platform_device *ahci_pdev;int ret; + of_id =of_match_device (imx_ahci_of_match, dev); +if (!of_id) +return -EINVAL ; + + type = (enum ahci_imx_type )of_id->data; + pdata = &imx_sata_pdata; + imxpriv =devm_kzalloc (dev,sizeof (*imxpriv),GFP_KERNEL );if (!imxpriv) {dev_err (dev,"can't alloc ahci_host_priv\n" );
@@ -222,6 +266,8 @@ static int imx_ahci_probe(struct platform_device *pdev) imxpriv->no_device = false; imxpriv->first_time = true; + imxpriv->type = type; + imxpriv->ahb_clk =devm_clk_get (dev,"ahb" );if (IS_ERR (imxpriv->ahb_clk)) {dev_err (dev,"can't get ahb clock.\n" );
@@ -229,6 +275,15 @@ static int imx_ahci_probe(struct platform_device *pdev) goto err_out; } +if (type ==AHCI_IMX53 ) { + imxpriv->sata_gate_clk =devm_clk_get (dev,"sata_gate" ); +if (IS_ERR (imxpriv->sata_gate_clk)) { +dev_err (dev,"can't get sata_gate clock.\n" ); + ret =PTR_ERR (imxpriv->sata_gate_clk); + goto err_out; + } + } + imxpriv->sata_ref_clk =devm_clk_get (dev,"sata_ref" );if (IS_ERR (imxpriv->sata_ref_clk)) {dev_err (dev,"can't get sata_ref clock.\n" );
@@ -239,14 +294,6 @@ static int imx_ahci_probe(struct platform_device *pdev) imxpriv->ahci_pdev = ahci_pdev;platform_set_drvdata (pdev, imxpriv); - of_id =of_match_device (imx_ahci_of_match, dev); -if (of_id) { - pdata = of_id->data; - }else { - ret = -EINVAL ; - goto err_out; - } - mem =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); irq =platform_get_resource (pdev,IORESOURCE_IRQ ,0 );if (!mem || !irq) {
@@ -262,41 +309,42 @@ static int imx_ahci_probe(struct platform_device *pdev) ahci_dev->dma_mask = &ahci_dev->coherent_dma_mask; ahci_dev->of_node = dev->of_node; - imxpriv->gpr = -syscon_regmap_lookup_by_compatible ("fsl,imx6q-iomuxc-gpr" ); - -if (IS_ERR (imxpriv->gpr)) { -dev_err (dev,"failed to find fsl,imx6q-iomux-gpr regmap\n" ); - ret =PTR_ERR (imxpriv->gpr); - goto err_out; +if (type ==AHCI_IMX6Q ) { + imxpriv->gpr =syscon_regmap_lookup_by_compatible ( +"fsl,imx6q-iomuxc-gpr" ); +if (IS_ERR (imxpriv->gpr)) { +dev_err (dev, +"failed to find fsl,imx6q-iomux-gpr regmap\n" ); +return PTR_ERR (imxpriv->gpr); + } + +/* +* Set PHY Paremeters, two steps to configure the GPR13, +* one write for rest of parameters, mask of first write +* is 0x07fffffe, and the other one write for setting +* the mpll_clk_en happens in imx_sata_clock_enable(). +*/ +regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , +IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK | +IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK | +IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK | +IMX6Q_GPR13_SATA_SPD_MODE_MASK | +IMX6Q_GPR13_SATA_MPLL_SS_EN | +IMX6Q_GPR13_SATA_TX_ATTEN_MASK | +IMX6Q_GPR13_SATA_TX_BOOST_MASK | +IMX6Q_GPR13_SATA_TX_LVL_MASK | +IMX6Q_GPR13_SATA_TX_EDGE_RATE | +IMX6Q_GPR13_SATA_MPLL_CLK_EN , +IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB | +IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M | +IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F | +IMX6Q_GPR13_SATA_SPD_MODE_3P0G | +IMX6Q_GPR13_SATA_MPLL_SS_EN | +IMX6Q_GPR13_SATA_TX_ATTEN_9_16 | +IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB | +IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); } -/* -* Set PHY Paremeters, two steps to configure the GPR13, -* one write for rest of parameters, mask of first write -* is 0x07fffffe, and the other one write for setting -* the mpll_clk_en happens in imx_sata_clock_enable(). -*/ -regmap_update_bits (imxpriv->gpr,IOMUXC_GPR13 , -IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK | -IMX6Q_GPR13_SATA_RX_LOS_LVL_MASK | -IMX6Q_GPR13_SATA_RX_DPLL_MODE_MASK | -IMX6Q_GPR13_SATA_SPD_MODE_MASK | -IMX6Q_GPR13_SATA_MPLL_SS_EN | -IMX6Q_GPR13_SATA_TX_ATTEN_MASK | -IMX6Q_GPR13_SATA_TX_BOOST_MASK | -IMX6Q_GPR13_SATA_TX_LVL_MASK | -IMX6Q_GPR13_SATA_TX_EDGE_RATE | -IMX6Q_GPR13_SATA_MPLL_CLK_EN , -IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB | -IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M | -IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F | -IMX6Q_GPR13_SATA_SPD_MODE_3P0G | -IMX6Q_GPR13_SATA_MPLL_SS_EN | -IMX6Q_GPR13_SATA_TX_ATTEN_9_16 | -IMX6Q_GPR13_SATA_TX_BOOST_3_33_DB | -IMX6Q_GPR13_SATA_TX_LVL_1_025_V ); - ret =platform_device_add_resources (ahci_pdev, res,2 );if (ret) goto err_out;
Signature · 1 line
1.8.4.2
PATCH v2 4/6 ARM: imx: imx53: Add SATA PHY clock
In reply to Marek VasutAdd SATA PHY clock which are derived from the USB PHY1 clock. Note that this patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to work correctly.
--- arch/arm/mach-imx/clk-imx51-imx53.c | 1 + include/dt-bindings/clock/imx5-clock.h | 3 ++- 2 files changed, 3 insertions(+), 1 deletion(-)
V2: Rename 'IMX5_CLK_SATA_PHY' to 'IMX5_CLK_SATA_REF' as well as
'sata_phy' to 'sata_ref' .
arch/arm/mach-imx/clk-imx51-imx53.c +1 -0
@@ -244,6 +244,7 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil, clk[IMX5_CLK_SPDIF0_GATE ] =imx_clk_gate2 ("spdif0_gate" ,"spdif0_com_sel" ,MXC_CCM_CCGR5 ,26 ); clk[IMX5_CLK_SPDIF_IPG_GATE ] =imx_clk_gate2 ("spdif_ipg_gate" ,"ipg" ,MXC_CCM_CCGR5 ,30 ); clk[IMX5_CLK_SAHARA_IPG_GATE ] =imx_clk_gate2 ("sahara_ipg_gate" ,"ipg" ,MXC_CCM_CCGR4 ,14 ); + clk[IMX5_CLK_SATA_REF ] =imx_clk_fixed_factor ("sata_ref" ,"usb_phy1_gate" ,1 ,1 );for (i =0 ; i <ARRAY_SIZE (clk); i++)if (IS_ERR (clk[i]))
include/dt-bindings/clock/imx5-clock.h +2 -1
@@ -197,6 +197,7 @@#define IMX5_CLK_SPDIF_IPG_GATE 185#define IMX5_CLK_OCRAM 186#define IMX5_CLK_SAHARA_IPG_GATE 187 -#define IMX5_CLK_END 188 +#define IMX5_CLK_SATA_REF 188 +#define IMX5_CLK_END 189#endif /* __DT_BINDINGS_CLOCK_IMX5_H */
Signature · 1 line
1.8.4.2
PATCH v2 4/6 ARM: imx: imx53: Add SATA PHY clock
Quoted 10 lines · Marek Vasut
Add SATA PHY clock which are derived from the USB PHY1 clock. Note that this patch derives the SATA PHY clock from USB PHY1 clock gate so that the SATA driver can ungate both the SATA PHY clock and USB PHY1 clock for the SATA to work correctly.
Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>
Applied patches #4, #5 and #6.
Shawn
PATCH 5/6 ARM: dts: imx53: Add AHCI SATA DT node
In reply to Marek VasutThe AHCI-IMX driver now supports i.MX53 as well. Add DT node.
--- arch/arm/boot/dts/imx53.dtsi | 11 +++++++++++ 1 file changed, 11 insertions(+)
V2: Rename 'IMX5_CLK_SATA_PHY' to 'IMX5_CLK_SATA_REF' as well as
'sata_phy' to 'sata_ref' .
arch/arm/boot/dts/imx53.dtsi +11 -0
@@ -86,6 +86,17 @@ interrupt-parent = <&tzic>; ranges; + sata: sata at 10000000 { + compatible = "fsl,imx53-ahci"; + reg = <0x10000000 0x1000>; + interrupts = <28>; + clocks = <&clks IMX5_CLK_SATA_GATE>, + <&clks IMX5_CLK_SATA_REF>, + <&clks IMX5_CLK_AHB>; + clock-names = "sata_gate", "sata_ref", "ahb"; + status = "disabled"; + }; + ipu: ipu at 18000000 { #crtc-cells = <1>; compatible = "fsl,imx53-ipu";
Signature · 1 line
1.8.4.2
PATCH 6/6 ARM: dts: imx53: Enable AHCI SATA for M53EVK
In reply to Marek Vasut--- arch/arm/boot/dts/imx53-m53evk.dts | 4 ++++ 1 file changed, 4 insertions(+)
arch/arm/boot/dts/imx53-m53evk.dts +4 -0
@@ -315,6 +315,10 @@ status = "okay"; }; +&sata { + status = "okay"; +}; + &ssi2 { fsl,mode = "i2s-slave"; status = "okay";
Signature · 1 line
1.8.4.2
PATCH v2 1/6 ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
In reply to Marek VasutQuoted 22 lines · Marek Vasut
We must clear this
IMX6Q_GPR13_SATA_MPLL_CLK_ENbit on i.MX6Q, otherwise Linux will fail to find the attached drive on some boards.This entire fix was:
Reported-by Eric Nelson <[email protected]>Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>--- drivers/ata/ahci_imx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)V2: Update the value in the comment from
0x7ffffffdto0x7ffffffedrivers/ata/ahci_imx.c +0
-0
drivers/ata/ahci_imx.c static int imx6q_sata_init(struct device *dev, void __iomem *mmio) · line 116
Quoted 5 lines
drivers/ata/ahci_imx.c +1
-1@@ -113,7 +113,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)/* * set PHY Paremeters, two steps to configure the GPR13, * one write for rest of parameters, mask of first write -* is 0x07fffffd, and the other one write for setting +* is 0x07fffffe, and the other one write for setting
0x07ffffff, d+2 = f,
bit 1 is IMX6Q_GPR13_SATA_MPLL_CLK_EN, which you just added bit 0 is IMX6Q_GPR13_SATA_TX_EDGE_RATE, which is also in your expression
Quoted 11 lines
drivers/ata/ahci_imx.c +1
-0* the mpll_clk_en. */ regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK@@ -125,6 +125,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio) | IMX6Q_GPR13_SATA_TX_BOOST_MASK |IMX6Q_GPR13_SATA_TX_LVL_MASK |IMX6Q_GPR13_SATA_TX_EDGE_RATE + |IMX6Q_GPR13_SATA_MPLL_CLK_EN ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
PATCH v2 1/6 ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
Quoted 18 lines · Troy Kisky
Quoted 17 lines · Marek Vasut
We must clear this
IMX6Q_GPR13_SATA_MPLL_CLK_ENbit on i.MX6Q, otherwise Linux will fail to find the attached drive on some boards.This entire fix was:
Reported-by Eric Nelson <[email protected]>Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>Cc Richard Zhu <[email protected]>Cc Tejun Heo <[email protected]>Cc Linux-IDE <[email protected]>--- drivers/ata/ahci_imx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)V2: Update the value in the comment from
0x7ffffffdto0x7ffffffe
Quoted 14 lines
drivers/ata/ahci_imx.c static int imx6q_sata_init(struct device *dev, void __iomem *mmio) · line 116
Quoted 10 lines
drivers/ata/ahci_imx.c +1
-1@@ -113,7 +113,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio)/* * set PHY Paremeters, two steps to configure the GPR13, * one write for rest of parameters, mask of first write -* is 0x07fffffd, and the other one write for setting +* is 0x07fffffe, and the other one write for setting
0x07ffffff, d+2 = f,
bit 1 isIMX6Q_GPR13_SATA_MPLL_CLK_EN, which you just added bit 0 isIMX6Q_GPR13_SATA_TX_EDGE_RATE, which is also in your expression
Ah, sorry. The mistake comes from my wrong bit math.
Shawn
Quoted 13 lines
Quoted 12 lines
drivers/ata/ahci_imx.c +1
-0* the mpll_clk_en. */ regmap_update_bits(imxpriv->gpr, 0x34, IMX6Q_GPR13_SATA_RX_EQ_VAL_MASK@@ -125,6 +125,7 @@ static int imx6q_sata_init(struct device *dev, void __iomem *mmio) | IMX6Q_GPR13_SATA_TX_BOOST_MASK |IMX6Q_GPR13_SATA_TX_LVL_MASK |IMX6Q_GPR13_SATA_TX_EDGE_RATE + |IMX6Q_GPR13_SATA_MPLL_CLK_EN ,IMX6Q_GPR13_SATA_RX_EQ_VAL_3_0_DB |IMX6Q_GPR13_SATA_RX_LOS_LVL_SATA2M |IMX6Q_GPR13_SATA_RX_DPLL_MODE_2P_4F
PATCH v2 1/6 ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
In reply to Marek VasutQuoted 8 lines · Marek Vasut
We must clear this
IMX6Q_GPR13_SATA_MPLL_CLK_ENbit on i.MX6Q, otherwise Linux will fail to find the attached drive on some boards.This entire fix was:
Reported-by Eric Nelson <[email protected]>Signed-off-by Marek Vasut <[email protected]>Cc Shawn Guo <[email protected]>
For patches 1 ~ 3, other than the error that Troy pointed out,