Skip to contentSkip to conversation

Add CAN FD infrastructure for CAN driver

PATCH In review Oliver Hartkopp 3 participants 10 messages Feb 28, 2014 – Mar 4, 2014 CAN network drivers

lore
Share & tools
lore
#0 lore raw

v9 cover Add CAN FD infrastructure for CAN driver

This is the patch series to extend the CAN driver infrastructure with CAN FD.

Changes v8 -> v9:

Fixed a whitepace issue in patch 4 and added a comment about the different configuration options.

*** BLURB HERE ***

Oliver Hartkopp (7):
can: preserve skbuff protocol in can_put_echo_skb
can: only send bitrate data via netlink when available
can: move sanity check for bitrate and tq into can_get_bittiming
can: provide a separate bittiming_const parameter to bittiming
functions
can: introduce the data bitrate configuration for CAN FD
can: allow to change the device mtu for CAN FD capable devices
can: add bittiming check at interface open for CAN FD

 drivers/net/can/dev.c            | 160 ++++++++++++++++++++++++++++++---------
 include/linux/can/dev.h          |   7 +-
 include/uapi/linux/can/netlink.h |   3 +
 3 files changed, 133 insertions(+), 37 deletions(-)
Signature · 1 line
1.9.0
#1 lore raw

PATCH v9 1/7 can: preserve skbuff protocol in can_put_echo_skb

The skbuff protocol value was formerly fixed/sanitized to ETH_P_CAN in can_put_echo_skb(). With CAN FD this value has to be preserved. This patch changes the hard assignment of the protocol value to a check of valid protocol values for CAN and CAN FD.

---
 drivers/net/can/dev.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/net/can/dev.c +3 -2
index c0563f1..e1a3741 100644
@@ -317,7 +317,9 @@ void can_put_echo_skb(struct sk_buff *skb, struct net_device *dev,
 	BUG_ON(idx >= priv->echo_skb_max);
 
 	/* check flag whether this packet has to be looped back */
-	if (!(dev->flags & IFF_ECHO) || skb->pkt_type != PACKET_LOOPBACK) {
+	if (!(dev->flags & IFF_ECHO) || skb->pkt_type != PACKET_LOOPBACK ||
+	    (skb->protocol != htons(ETH_P_CAN) &&
+	     skb->protocol != htons(ETH_P_CANFD))) {
 		kfree_skb(skb);
 		return;
 	}
@@ -329,7 +331,6 @@ void can_put_echo_skb(struct sk_buff *skb, struct net_device *dev,
 			return;
 
 		/* make settings for echo to reduce code in irq context */
-		skb->protocol = htons(ETH_P_CAN);
 		skb->pkt_type = PACKET_BROADCAST;
 		skb->ip_summed = CHECKSUM_UNNECESSARY;
 		skb->dev = dev;
Signature · 1 line
1.9.0
#2 lore raw

PATCH v9 2/7 can: only send bitrate data via netlink when available

In reply to Oliver Hartkopp

When setting the bitrate both can_calc_bittiming() and can_fixup_bittiming() lead to the bitrate variable to be set, when a proper bit timing is available. Only then the bitrate configuration is stored for the device, so checking for priv->bittiming.bitrate is always sufficient.

---
 drivers/net/can/dev.c | 10 ++++++----
 1 file changed, 6 insertions(+), 4 deletions(-)
drivers/net/can/dev.c +6 -4
index e1a3741..de04eac 100644
@@ -606,7 +606,7 @@ int open_candev(struct net_device *dev)
 {
 	struct can_priv *priv = netdev_priv(dev);
 
-	if (!priv->bittiming.tq && !priv->bittiming.bitrate) {
+	if (!priv->bittiming.bitrate) {
 		netdev_err(dev, "bit-timing not yet defined\n");
 		return -EINVAL;
 	}
@@ -719,7 +719,8 @@ static size_t can_get_size(const struct net_device *dev)
 	struct can_priv *priv = netdev_priv(dev);
 	size_t size = 0;
 
-	size += nla_total_size(sizeof(struct can_bittiming));	/* IFLA_CAN_BITTIMING */
+	if (priv->bittiming.bitrate)				/* IFLA_CAN_BITTIMING */
+		size += nla_total_size(sizeof(struct can_bittiming));
 	if (priv->bittiming_const)				/* IFLA_CAN_BITTIMING_CONST */
 		size += nla_total_size(sizeof(struct can_bittiming_const));
 	size += nla_total_size(sizeof(struct can_clock));	/* IFLA_CAN_CLOCK */
@@ -741,8 +742,9 @@ static int can_fill_info(struct sk_buff *skb, const struct net_device *dev)
 
 	if (priv->do_get_state)
 		priv->do_get_state(dev, &state);
-	if (nla_put(skb, IFLA_CAN_BITTIMING,
-		    sizeof(priv->bittiming), &priv->bittiming) ||
+	if ((priv->bittiming.bitrate &&
+	     nla_put(skb, IFLA_CAN_BITTIMING,
+		     sizeof(priv->bittiming), &priv->bittiming)) ||
 	    (priv->bittiming_const &&
 	     nla_put(skb, IFLA_CAN_BITTIMING_CONST,
 		     sizeof(*priv->bittiming_const), priv->bittiming_const)) ||
Signature · 1 line
1.9.0
#3 lore raw

PATCH v9 3/7 can: move sanity check for bitrate and tq into can_get_bittiming

In reply to Oliver Hartkopp

This patch moves a sanity check in order to have a second user for CAN FD.

---
 drivers/net/can/dev.c | 17 +++++++++++------
 1 file changed, 11 insertions(+), 6 deletions(-)
drivers/net/can/dev.c +11 -6
index de04eac..89fc798 100644
@@ -263,12 +263,19 @@ static int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt)
 	if (priv->bittiming_const) {
 
 		/* Non-expert mode? Check if the bitrate has been pre-defined */
-		if (!bt->tq)
+		if (!bt->tq) {
 			/* Determine bit-timing parameters */
-			err = can_calc_bittiming(dev, bt);
-		else
+			if (bt->bitrate)
+				err = can_calc_bittiming(dev, bt);
+			else
+				return -EINVAL;
+		} else {
 			/* Check bit-timing params and calculate proper brp */
-			err = can_fixup_bittiming(dev, bt);
+			if (!bt->bitrate)
+				err = can_fixup_bittiming(dev, bt);
+			else
+				return -EINVAL;
+		}
 		if (err)
 			return err;
 	}
@@ -667,8 +674,6 @@ static int can_changelink(struct net_device *dev,
 		if (dev->flags & IFF_UP)
 			return -EBUSY;
 		memcpy(&bt, nla_data(data[IFLA_CAN_BITTIMING]), sizeof(bt));
-		if ((!bt.bitrate && !bt.tq) || (bt.bitrate && bt.tq))
-			return -EINVAL;
 		err = can_get_bittiming(dev, &bt);
 		if (err)
 			return err;
Signature · 1 line
1.9.0
#4 lore raw

PATCH v9 4/7 can: provide a separate bittiming_const parameter to bittiming functions

In reply to Oliver Hartkopp

As the bittiming calculation functions are to be used with different bittiming_const structures for CAN and CAN FD the direct reference to priv->bittiming_const inside these functions has to be removed.

Also simplify the return value generation in can_get_bittiming() as only correct return values of can_[calc|fixup]_bittiming() lead to a return value of zero. And moved the check for existing bittiming const to one place.

---
 drivers/net/can/dev.c | 59 ++++++++++++++++++++++-----------------------------
 1 file changed, 25 insertions(+), 34 deletions(-)
drivers/net/can/dev.c +25 -34
index 89fc798..8141290 100644
@@ -99,10 +99,10 @@ static int can_update_spt(const struct can_bittiming_const *btc,
 	return 1000 * (tseg + 1 - *tseg2) / (tseg + 1);
 }
 
-static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt)
+static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt,
+			      const struct can_bittiming_const *btc)
 {
 	struct can_priv *priv = netdev_priv(dev);
-	const struct can_bittiming_const *btc = priv->bittiming_const;
 	long rate, best_rate = 0;
 	long best_error = 1000000000, error = 0;
 	int best_tseg = 0, best_brp = 0, brp = 0;
@@ -110,9 +110,6 @@ static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt)
 	int spt_error = 1000, spt = 0, sampl_pt;
 	u64 v64;
 
-	if (!priv->bittiming_const)
-		return -ENOTSUPP;
-
 	/* Use CIA recommended sample points */
 	if (bt->sample_point) {
 		sampl_pt = bt->sample_point;
@@ -204,7 +201,8 @@ static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt)
 	return 0;
 }
 #else /* !CONFIG_CAN_CALC_BITTIMING */
-static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt)
+static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt,
+			      const struct can_bittiming_const *btc)
 {
 	netdev_err(dev, "bit-timing calculation not available\n");
 	return -EINVAL;
@@ -217,16 +215,13 @@ static int can_calc_bittiming(struct net_device *dev, struct can_bittiming *bt)
  * prescaler value brp. You can find more information in the header
  * file linux/can/netlink.h.
  */
-static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt)
+static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt,
+			       const struct can_bittiming_const *btc)
 {
 	struct can_priv *priv = netdev_priv(dev);
-	const struct can_bittiming_const *btc = priv->bittiming_const;
 	int tseg1, alltseg;
 	u64 brp64;
 
-	if (!priv->bittiming_const)
-		return -ENOTSUPP;
-
 	tseg1 = bt->prop_seg + bt->phase_seg1;
 	if (!bt->sjw)
 		bt->sjw = 1;
@@ -254,33 +249,29 @@ static int can_fixup_bittiming(struct net_device *dev, struct can_bittiming *bt)
 	return 0;
 }
 
-static int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt)
+static int can_get_bittiming(struct net_device *dev, struct can_bittiming *bt,
+			     const struct can_bittiming_const *btc)
 {
-	struct can_priv *priv = netdev_priv(dev);
 	int err;
 
 	/* Check if the CAN device has bit-timing parameters */
-	if (priv->bittiming_const) {
-
-		/* Non-expert mode? Check if the bitrate has been pre-defined */
-		if (!bt->tq) {
-			/* Determine bit-timing parameters */
-			if (bt->bitrate)
-				err = can_calc_bittiming(dev, bt);
-			else
-				return -EINVAL;
-		} else {
-			/* Check bit-timing params and calculate proper brp */
-			if (!bt->bitrate)
-				err = can_fixup_bittiming(dev, bt);
-			else
-				return -EINVAL;
-		}
-		if (err)
-			return err;
-	}
+	if (!btc)
+		return -ENOTSUPP;
 
-	return 0;
+	/*
+	 * Depending on the given can_bittiming parameter structure the CAN
+	 * timing parameters are calculated based on the provided bitrate OR
+	 * alternatively the CAN timing parameters (tq, prop_seg, etc.) are
+	 * provided directly which are then checked and fixed up.
+	 */
+	if (!bt->tq && bt->bitrate)
+		err = can_calc_bittiming(dev, bt, btc);
+	else if (bt->tq && !bt->bitrate)
+		err = can_fixup_bittiming(dev, bt, btc);
+	else
+		err = -EINVAL;
+
+	return err;
 }
 
 /*
@@ -674,7 +665,7 @@ static int can_changelink(struct net_device *dev,
 		if (dev->flags & IFF_UP)
 			return -EBUSY;
 		memcpy(&bt, nla_data(data[IFLA_CAN_BITTIMING]), sizeof(bt));
-		err = can_get_bittiming(dev, &bt);
+		err = can_get_bittiming(dev, &bt, priv->bittiming_const);
 		if (err)
 			return err;
 		memcpy(&priv->bittiming, &bt, sizeof(bt));
Signature · 1 line
1.9.0
#5 lore raw

PATCH v9 5/7 can: introduce the data bitrate configuration for CAN FD

In reply to Oliver Hartkopp

As CAN FD offers a second bitrate for the data section of the CAN frame the infrastructure for storing and configuring this second bitrate is introduced. Improved the readability of the if-statement by inserting some newlines.

---
 drivers/net/can/dev.c            | 45 +++++++++++++++++++++++++++++++++++++++-
 include/linux/can/dev.h          |  6 ++++--
 include/uapi/linux/can/netlink.h |  2 ++
 3 files changed, 50 insertions(+), 3 deletions(-)
drivers/net/can/dev.c +44 -1
index 8141290..1eafa6cc 100644
@@ -647,6 +647,10 @@ static const struct nla_policy can_policy[IFLA_CAN_MAX + 1] = {
 				= { .len = sizeof(struct can_bittiming_const) },
 	[IFLA_CAN_CLOCK]	= { .len = sizeof(struct can_clock) },
 	[IFLA_CAN_BERR_COUNTER]	= { .len = sizeof(struct can_berr_counter) },
+	[IFLA_CAN_DATA_BITTIMING]
+				= { .len = sizeof(struct can_bittiming) },
+	[IFLA_CAN_DATA_BITTIMING_CONST]
+				= { .len = sizeof(struct can_bittiming_const) },
 };
 
 static int can_changelink(struct net_device *dev,
@@ -678,6 +682,27 @@ static int can_changelink(struct net_device *dev,
 		}
 	}
 
+	if (data[IFLA_CAN_DATA_BITTIMING]) {
+		struct can_bittiming dbt;
+
+		/* Do not allow changing bittiming while running */
+		if (dev->flags & IFF_UP)
+			return -EBUSY;
+		memcpy(&dbt, nla_data(data[IFLA_CAN_DATA_BITTIMING]),
+		       sizeof(dbt));
+		err = can_get_bittiming(dev, &dbt, priv->data_bittiming_const);
+		if (err)
+			return err;
+		memcpy(&priv->data_bittiming, &dbt, sizeof(dbt));
+
+		if (priv->do_set_data_bittiming) {
+			/* Finally, set the bit-timing registers */
+			err = priv->do_set_data_bittiming(dev);
+			if (err)
+				return err;
+		}
+	}
+
 	if (data[IFLA_CAN_CTRLMODE]) {
 		struct can_ctrlmode *cm;
 
@@ -725,6 +750,10 @@ static size_t can_get_size(const struct net_device *dev)
 	size += nla_total_size(sizeof(u32));			/* IFLA_CAN_RESTART_MS */
 	if (priv->do_get_berr_counter)				/* IFLA_CAN_BERR_COUNTER */
 		size += nla_total_size(sizeof(struct can_berr_counter));
+	if (priv->data_bittiming.bitrate)			/* IFLA_CAN_DATA_BITTIMING */
+		size += nla_total_size(sizeof(struct can_bittiming));
+	if (priv->data_bittiming_const)				/* IFLA_CAN_DATA_BITTIMING_CONST */
+		size += nla_total_size(sizeof(struct can_bittiming_const));
 
 	return size;
 }
@@ -738,20 +767,34 @@ static int can_fill_info(struct sk_buff *skb, const struct net_device *dev)
 
 	if (priv->do_get_state)
 		priv->do_get_state(dev, &state);
+
 	if ((priv->bittiming.bitrate &&
 	     nla_put(skb, IFLA_CAN_BITTIMING,
 		     sizeof(priv->bittiming), &priv->bittiming)) ||
+
 	    (priv->bittiming_const &&
 	     nla_put(skb, IFLA_CAN_BITTIMING_CONST,
 		     sizeof(*priv->bittiming_const), priv->bittiming_const)) ||
+
 	    nla_put(skb, IFLA_CAN_CLOCK, sizeof(cm), &priv->clock) ||
 	    nla_put_u32(skb, IFLA_CAN_STATE, state) ||
 	    nla_put(skb, IFLA_CAN_CTRLMODE, sizeof(cm), &cm) ||
 	    nla_put_u32(skb, IFLA_CAN_RESTART_MS, priv->restart_ms) ||
+
 	    (priv->do_get_berr_counter &&
 	     !priv->do_get_berr_counter(dev, &bec) &&
-	     nla_put(skb, IFLA_CAN_BERR_COUNTER, sizeof(bec), &bec)))
+	     nla_put(skb, IFLA_CAN_BERR_COUNTER, sizeof(bec), &bec)) ||
+
+	    (priv->data_bittiming.bitrate &&
+	     nla_put(skb, IFLA_CAN_DATA_BITTIMING,
+		     sizeof(priv->data_bittiming), &priv->data_bittiming)) ||
+
+	    (priv->data_bittiming_const &&
+	     nla_put(skb, IFLA_CAN_DATA_BITTIMING_CONST,
+		     sizeof(*priv->data_bittiming_const),
+		     priv->data_bittiming_const)))
 		return -EMSGSIZE;
+
 	return 0;
 }
 
include/linux/can/dev.h +4 -2
index dc5f902..8adaee9 100644
@@ -33,8 +33,9 @@ enum can_mode {
 struct can_priv {
 	struct can_device_stats can_stats;
 
-	struct can_bittiming bittiming;
-	const struct can_bittiming_const *bittiming_const;
+	struct can_bittiming bittiming, data_bittiming;
+	const struct can_bittiming_const *bittiming_const,
+		*data_bittiming_const;
 	struct can_clock clock;
 
 	enum can_state state;
@@ -45,6 +46,7 @@ struct can_priv {
 	struct timer_list restart_timer;
 
 	int (*do_set_bittiming)(struct net_device *dev);
+	int (*do_set_data_bittiming)(struct net_device *dev);
 	int (*do_set_mode)(struct net_device *dev, enum can_mode mode);
 	int (*do_get_state)(const struct net_device *dev,
 			    enum can_state *state);
include/uapi/linux/can/netlink.h +2 -0
index df944ed..b41933d 100644
@@ -122,6 +122,8 @@ enum {
 	IFLA_CAN_RESTART_MS,
 	IFLA_CAN_RESTART,
 	IFLA_CAN_BERR_COUNTER,
+	IFLA_CAN_DATA_BITTIMING,
+	IFLA_CAN_DATA_BITTIMING_CONST,
 	__IFLA_CAN_MAX
 };
 
Signature · 1 line
1.9.0
#6 lore raw

PATCH v9 6/7 can: allow to change the device mtu for CAN FD capable devices

In reply to Oliver Hartkopp

The configuration for CAN FD depends on CAN_CTRLMODE_FD enabled in the driver specific ctrlmode_supported capabilities.

The configuration can be done either with the 'fd { on | off }' option in the 'ip' tool from iproute2 or by setting the CAN netdevice MTU to CAN_MTU (16) or to CANFD_MTU (72).

---
 drivers/net/can/dev.c            | 40 ++++++++++++++++++++++++++++++++++++++++
 include/linux/can/dev.h          |  1 +
 include/uapi/linux/can/netlink.h |  1 +
 3 files changed, 42 insertions(+)
drivers/net/can/dev.c +40 -0
index 1eafa6cc..f3151d9 100644
@@ -595,6 +595,40 @@ void free_candev(struct net_device *dev)
 EXPORT_SYMBOL_GPL(free_candev);
 
 /*
+ * changing MTU and control mode for CAN/CANFD devices
+ */
+int can_change_mtu(struct net_device *dev, int new_mtu)
+{
+	struct can_priv *priv = netdev_priv(dev);
+
+	/* Do not allow changing the MTU while running */
+	if (dev->flags & IFF_UP)
+		return -EBUSY;
+
+	/* allow change of MTU according to the CANFD ability of the device */
+	switch (new_mtu) {
+
+	case CAN_MTU:
+		priv->ctrlmode &= ~CAN_CTRLMODE_FD;
+		break;
+
+	case CANFD_MTU:
+		if (!(priv->ctrlmode_supported & CAN_CTRLMODE_FD))
+			return -EINVAL;
+
+		priv->ctrlmode |= CAN_CTRLMODE_FD;
+		break;
+
+	default:
+			return -EINVAL;
+	}
+
+	dev->mtu = new_mtu;
+	return 0;
+}
+EXPORT_SYMBOL_GPL(can_change_mtu);
+
+/*
  * Common open function when the device gets opened.
  *
  * This function should be called in the open function of the device
@@ -714,6 +748,12 @@ static int can_changelink(struct net_device *dev,
 			return -EOPNOTSUPP;
 		priv->ctrlmode &= ~cm->mask;
 		priv->ctrlmode |= cm->flags;
+
+		/* CAN_CTRLMODE_FD can only be set when driver supports FD */
+		if (priv->ctrlmode & CAN_CTRLMODE_FD)
+			dev->mtu = CANFD_MTU;
+		else
+			dev->mtu = CAN_MTU;
 	}
 
 	if (data[IFLA_CAN_RESTART_MS]) {
include/linux/can/dev.h +1 -0
index 8adaee9..3ce5e52 100644
@@ -113,6 +113,7 @@ struct can_priv *safe_candev_priv(struct net_device *dev);
 
 int open_candev(struct net_device *dev);
 void close_candev(struct net_device *dev);
+int can_change_mtu(struct net_device *dev, int new_mtu);
 
 int register_candev(struct net_device *dev);
 void unregister_candev(struct net_device *dev);
include/uapi/linux/can/netlink.h +1 -0
index b41933d..7e2e186 100644
@@ -96,6 +96,7 @@ struct can_ctrlmode {
 #define CAN_CTRLMODE_3_SAMPLES		0x04	/* Triple sampling mode */
 #define CAN_CTRLMODE_ONE_SHOT		0x08	/* One-Shot mode */
 #define CAN_CTRLMODE_BERR_REPORTING	0x10	/* Bus-error reporting */
+#define CAN_CTRLMODE_FD			0x20	/* CAN FD mode */
 
 /*
  * CAN device statistics
Signature · 1 line
1.9.0
#7 lore raw

PATCH v9 7/7 can: add bittiming check at interface open for CAN FD

In reply to Oliver Hartkopp

Additionally to have the second (data) bitrate available the data bitrate has to be greater or equal to the arbitration bitrate in CAN FD.

---
 drivers/net/can/dev.c | 8 ++++++++
 1 file changed, 8 insertions(+)
drivers/net/can/dev.c +8 -0
index f3151d9..6fce037 100644
@@ -643,6 +643,14 @@ int open_candev(struct net_device *dev)
 		return -EINVAL;
 	}
 
+	/* For CAN FD the data bitrate has to be >= the arbitration bitrate */
+	if ((priv->ctrlmode & CAN_CTRLMODE_FD) &&
+	    (!priv->data_bittiming.bitrate ||
+	     (priv->data_bittiming.bitrate < priv->bittiming.bitrate))) {
+		netdev_err(dev, "incorrect/missing data bit-timing\n");
+		return -EINVAL;
+	}
+
 	/* Switch carrier on if device was stopped while in bus-off state */
 	if (!netif_carrier_ok(dev))
 		netif_carrier_on(dev);
Signature · 1 line
1.9.0
#8 lore raw
In reply to Oliver Hartkopp
Quoted 19 lines · Oliver Hartkopp

This is the patch series to extend the CAN driver infrastructure with CAN FD.

Changes v8 -> v9:

Fixed a whitepace issue in patch 4 and added a comment about the different configuration options.

*** BLURB HERE ***

Oliver Hartkopp (7):
can: preserve skbuff protocol in can_put_echo_skb
can: only send bitrate data via netlink when available
can: move sanity check for bitrate and tq into can_get_bittiming
can: provide a separate bittiming_const parameter to bittiming
functions
can: introduce the data bitrate configuration for CAN FD
can: allow to change the device mtu for CAN FD capable devices
can: add bittiming check at interface open for CAN FD

Quoted 4 lines
 drivers/net/can/dev.c            | 160 ++++++++++++++++++++++++++++++---------
 include/linux/can/dev.h          |   7 +-
 include/uapi/linux/can/netlink.h |   3 +
 3 files changed, 133 insertions(+), 37 deletions(-)

Stephane, I'll add your Acked-by that you have given for the v8 of this series.

Marc

Signature · 4 lines
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |
#9 lore raw

Hi Marc,

You did well !

Stéphane

Quoted 20 lines · Marc Kleine-Budde
Quoted 19 lines · Oliver Hartkopp

This is the patch series to extend the CAN driver infrastructure with CAN FD.

Changes v8 -> v9:

Fixed a whitepace issue in patch 4 and added a comment about the different configuration options.

*** BLURB HERE ***

Oliver Hartkopp (7):
can: preserve skbuff protocol in can_put_echo_skb
can: only send bitrate data via netlink when available
can: move sanity check for bitrate and tq into can_get_bittiming
can: provide a separate bittiming_const parameter to bittiming
functions
can: introduce the data bitrate configuration for CAN FD
can: allow to change the device mtu for CAN FD capable devices
can: add bittiming check at interface open for CAN FD

Quoted 9 lines
Quoted 4 lines
  drivers/net/can/dev.c            | 160 ++++++++++++++++++++++++++++++---------
  include/linux/can/dev.h          |   7 +-
  include/uapi/linux/can/netlink.h |   3 +
  3 files changed, 133 insertions(+), 37 deletions(-)

Stephane, I'll add your Acked-by that you have given for the v8 of this series.

Marc

--
PEAK-System Technik GmbH, Otto-Roehm-Strasse 69, D-64293 Darmstadt Geschaeftsleitung: A.Gach/U.Wilhelm,St.Nr.:007/241/13586 FA Darmstadt HRB-9183 Darmstadt, Ust.IdNr.:DE 202220078, WEE-Reg.-Nr.: DE39305391 Tel.+49 (0)6151-817320 / Fax:+49 (0)6151-817329, [email protected]