hwmon: Driver for TI TMP103 temperature sensor
PATCH v2 1/1 hwmon: Driver for TI TMP103 temperature sensor
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
---
- change for v2:
- add comments from GuenterRoeck:
- remove Cc from commit subject
- add devicetree mailinglist
- move Documentation to Documentation/hwmon/tmp103
- remove devicetree bindings from Documentation
- add compatible string to "Documentation/devicetree/bindings/i2c/trivial-devices.txt"
- remove CamelCase
- fix Codingstyle issues
- use ATTRIBUTE_GROUPS and devm_hwmon_device_register_with_groups()
- remove unsused define TMP103_CONFIG_RD_ONLY
- restore config register when exit()
- use regmap
.../devicetree/bindings/i2c/trivial-devices.txt | 1 + Documentation/hwmon/tmp103 | 28 ++ drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/tmp103.c | 304 +++++++++++++++++++++ 5 files changed, 344 insertions(+) create mode 100644 Documentation/hwmon/tmp103 create mode 100644 drivers/hwmon/tmp103.c
Documentation/devicetree/bindings/i2c/trivial-devices.txt +1 -0
@@ -83,5 +83,6 @@ stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor winbond,wpct301 i2c trusted platform module (TPM)
Documentation/hwmon/tmp103 new file +28 -0
@@ -0,0 +1,28 @@ +Kernel driver tmp103 +==================== + +Supported chips: + * Texas Instruments TMP103 + Prefix: 'tmp103' + Addresses scanned: none + Product info and datasheet: http://www.ti.com/product/tmp103 + +Author: + Heiko Schocher <[email protected]> + +Description +----------- + +The TMP103 is a digital output temperature sensor in a four-ball +wafer chip-scale package (WCSP). The TMP103 is capable of reading +temperatures to a resolution of 1°C. The TMP103 is specified for +operation over a temperature range of –40°C to +125°C. + +Resolution: 8 Bits +Accuracy: ±1°C Typ (–10°C to +100°C) + +The driver provides the common sysfs-interface for temperatures (see +Documentation/hwmon/sysfs-interface under Temperatures). + +please refer how to instantiate this driver: +Documentation/i2c/instantiating-devices
drivers/hwmon/Kconfig +10 -0
@@ -1381,6 +1381,16 @@ config SENSORS_TMP102 This driver can also be built as a module. If so, the module will be called tmp102. +config SENSORS_TMP103 + tristate "Texas Instruments TMP103" + depends on I2C + help + If you say yes here you get support for Texas Instruments TMP103 + sensor chips. + + This driver can also be built as a module. If so, the module + will be called tmp103. + config SENSORS_TMP401 tristate "Texas Instruments TMP401 and compatibles" depends on I2C
drivers/hwmon/Makefile +1 -0
@@ -134,6 +134,7 @@ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o obj-$(CONFIG_SENSORS_TMP102) += tmp102.o +obj-$(CONFIG_SENSORS_TMP103) += tmp103.o obj-$(CONFIG_SENSORS_TMP401) += tmp401.o obj-$(CONFIG_SENSORS_TMP421) += tmp421.o obj-$(CONFIG_SENSORS_TWL4030_MADC)+= twl4030-madc-hwmon.o
drivers/hwmon/tmp103.c new file +304 -0
304 lines not on this page · raw message
Signature · 1 line
1.8.3.1
Guenter Roeck
maintainerQuoted 7 lines · Heiko Schocher
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
Signed-off-by Heiko Schocher <[email protected]>
Hello Heiko,
Couple of additional comments.
Thanks,
Guenter
Quoted 66 lines
---
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>- change for v2:
- add comments from GuenterRoeck:
- remove Cc from commit subject
- add devicetree mailinglist
- move Documentation toDocumentation/hwmon/tmp103
- remove devicetree bindings from Documentation
- add compatible string to "Documentation/devicetree/bindings/i2c/trivial-devices.txt"
- remove CamelCase
- fix Codingstyle issues
- useATTRIBUTE_GROUPSanddevm_hwmon_device_register_with_groups()
- remove unsused defineTMP103_CONFIG_RD_ONLY
- restore config register whenexit()
- use regmap.../devicetree/bindings/i2c/trivial-devices.txt | 1 + Documentation/hwmon/tmp103 | 28 ++ drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/tmp103.c | 304 +++++++++++++++++++++ 5 files changed, 344 insertions(+)create mode 100644
Documentation/hwmon/tmp103
create mode 100644drivers/hwmon/tmp103.cDocumentation/devicetree/bindings/i2c/trivial-devices.txt +1
-0@@ -83,5 +83,6 @@ stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor winbond,wpct301 i2c trusted platform module (TPM)Documentation/hwmon/tmp103 new file +17
-0@@ -0,0 +1,28 @@ +Kernel driver tmp103 +==================== + +Supported chips: + * Texas Instruments TMP103 + Prefix: 'tmp103' + Addresses scanned: none + Product info and datasheet: http://www.ti.com/product/tmp103 + +Author: + Heiko Schocher <[email protected]> + +Description +----------- + +The TMP103 is a digital output temperature sensor in a four-ball +wafer chip-scale package (WCSP). The TMP103 is capable of reading
Documentation/hwmon/tmp103 line 27
Quoted 10 lines
Documentation/hwmon/tmp103 new file +10
-0+temperatures to a resolution of 1°C. The TMP103 is specified for +operation over a temperature range of –40°C to +125°C. + +Resolution: 8 Bits +Accuracy: ±1°C Typ (–10°C to +100°C) + +The driver provides the common sysfs-interface for temperatures (see +Documentation/hwmon/sysfs-interface under Temperatures). + +please refer how to instantiate this driver:
s/please/Please/
Quoted 80 lines
Documentation/hwmon/tmp103 new file +1
-0+Documentation/i2c/instantiating-devicesdrivers/hwmon/Kconfig +10
-0@@ -1381,6 +1381,16 @@ config SENSORS_TMP102 This driver can also be built as a module. If so, the module will be called tmp102. +config SENSORS_TMP103 + tristate "Texas Instruments TMP103" + depends on I2C + help + If you say yes here you get support for Texas Instruments TMP103 + sensor chips. + + This driver can also be built as a module. If so, the module + will be called tmp103. + config SENSORS_TMP401 tristate "Texas Instruments TMP401 and compatibles" depends on I2Cdrivers/hwmon/Makefile +1
-0@@ -134,6 +134,7 @@ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o obj-$(CONFIG_SENSORS_TMP102) += tmp102.o +obj-$(CONFIG_SENSORS_TMP103) += tmp103.o obj-$(CONFIG_SENSORS_TMP401) += tmp401.o obj-$(CONFIG_SENSORS_TMP421) += tmp421.o obj-$(CONFIG_SENSORS_TWL4030_MADC)+= twl4030-madc-hwmon.odrivers/hwmon/tmp103.c new file +40
-0@@ -0,0 +1,304 @@ +/* +* Texas Instruments TMP103 SMBus temperature sensor driver +* Copyright (C) 2014 Heiko Schocher <[email protected]> +* +* Based on: +* Texas Instruments TMP102 SMBus temperature sensor driver +* +* Copyright (C) 2010 Steven King <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/device.h> +#include <linux/jiffies.h> +#include <linux/regmap.h> + +#define DRIVER_NAME "tmp103" + +#define TMP103_TEMP_REG 0x00 +#define TMP103_CONF_REG 0x01 +#define TMP103_TLOW_REG 0x02 +#define TMP103_THIGH_REG 0x03 +
drivers/hwmon/tmp103.c line 50
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+#define TMP103_CONF_M0 0x01 +#define TMP103_CONF_M1 0x02 +#define TMP103_CONF_LC 0x04 +#define TMP103_CONF_FL 0x08 +#define TMP103_CONF_FH 0x10 +#define TMP103_CONF_CR0 0x20 +#define TMP103_CONF_CR1 0x40 +#define TMP103_CONF_ID 0x80 +#define TMP103_CONF_SD (TMP103_CONF_M0 | TMP103_CONF_M1) +
No tab between #define and the actual definition, please.
drivers/hwmon/tmp103.c line 52
Quoted 2 lines
drivers/hwmon/tmp103.c new file +2
-0+struct tmp103 { +struct i2c_client *client;
No longer needed. See below.
drivers/hwmon/tmp103.c line 58
Quoted 6 lines
drivers/hwmon/tmp103.c new file +6
-0+struct device *hwmon_dev; +struct regmap *regmap; +struct mutex lock; +unsigned int config_orig; +unsigned long last_update; +int temp[3 ];
Both no longer needed.
Actually, the entire structure is not really needed anymore with the changes suggested below. The only value still needed would be regmap, and you could store that directly in drvdata.
Quoted 7 lines
drivers/hwmon/tmp103.c new file +7
-0+}; + +static inline int tmp103_reg_to_mc (s8 val) +{ +return val *1000 ; +} +
drivers/hwmon/tmp103.c line 75
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+static inline u8 tmp103_mc_to_reg (int val) +{ +return DIV_ROUND_CLOSEST (val,1000 ); +} + +static const u8 tmp103_reg[] = { +TMP103_TEMP_REG , +TMP103_TLOW_REG , +TMP103_THIGH_REG , +};
No longer needed; you can put the register directly into sda->index.
drivers/hwmon/tmp103.c line 85
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ +#define TMP103_INVALID 0xffff + +static ssize_t tmp103_show_temp (struct device *dev, +struct device_attribute *attr, +char *buf) +{ +struct sensor_device_attribute *sda =to_sensor_dev_attr (attr); +struct i2c_client *client =to_i2c_client (dev); +struct tmp103 *tmp103 =i2c_get_clientdata (client);
Too complicated. Attributes are now attached to the hwmon device, and tmp103 can be retrieved from there.
struct tmp103 *tmp103 = dev_get_drvdata(dev); or, with all the changes I suggested, even simpler struct regmap *regmap = dev_get_drvdata(dev);
drivers/hwmon/tmp103.c line 97
Quoted 12 lines
drivers/hwmon/tmp103.c new file +12
-0+unsigned int status; +int ret; + +mutex_lock (&tmp103->lock); +if (time_after (jiffies, tmp103->last_update +HZ /3 )) { +int i; + +for (i =0 ; i <ARRAY_SIZE (tmp103->temp); ++i) { + ret =regmap_read (tmp103->regmap, tmp103_reg[i], + &status); +if (ret <0 ) + tmp103->temp[i] =TMP103_INVALID ;
Good idea, but not really what we'd want to see. In this case the error should be reported to use space, ie return the value of 'ret', not "invalid". Also, you don't need to read all registers here, and just forget about local caching (not worth it).
Suggested replacement below.
drivers/hwmon/tmp103.c line 109
Quoted 12 lines
drivers/hwmon/tmp103.c new file +12
-0+else + tmp103->temp[i] =tmp103_reg_to_mc (status); + } + tmp103->last_update = jiffies; + } +mutex_unlock (&tmp103->lock); + +if (tmp103->temp[sda->index] !=TMP103_INVALID ) +return sprintf (buf,"%d\n" , tmp103->temp[sda->index]); + +return sprintf (buf,"invalid\n" ); +}
static ssize_t tmp103_show_temp(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct sensor_device_attribute *sda = to_sensor_dev_attr(attr);
struct tmp103 *tmp103 = dev_get_drvdata(dev); /* or struct regmap *regmap = dev_get_drvdata(dev); */
unsigned int regval;
int ret;
ret = regmap_read(tmp103->regmap, sda->index, ®val);
if (ret < 0)
return ret;
return return sprintf(buf, "%d\n", tmp103_reg_to_mc(regval));
}drivers/hwmon/tmp103.c line 117
Quoted 8 lines
drivers/hwmon/tmp103.c new file +8
-0+ +static ssize_t tmp103_set_temp (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct sensor_device_attribute *sda =to_sensor_dev_attr (attr); +struct i2c_client *client =to_i2c_client (dev); +struct tmp103 *tmp103 =i2c_get_clientdata (client);
Same as above.
struct tmp103 *tmp103 = dev_get_drvdata(dev);
drivers/hwmon/tmp103.c line 128
Quoted 11 lines
drivers/hwmon/tmp103.c new file +11
-0+long val; +int ret; + +if (kstrtol (buf,10 , &val) <0 ) +return -EINVAL ; + + val =clamp_val (val,-55000 ,127000 ); +mutex_lock (&tmp103->lock); + tmp103->temp[sda->index] = val; + ret =regmap_write (tmp103->regmap, tmp103_reg[sda->index], +tmp103_mc_to_reg (val));
After dropping tmp103->temp[] you don't need the lock anymore, which means it can go away completely.
drivers/hwmon/tmp103.c line 134
Quoted 6 lines
drivers/hwmon/tmp103.c new file +6
-0+mutex_unlock (&tmp103->lock); +return ret ? : count; +} + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, tmp103_show_temp, NULL , 0); +
As suggested above, instead of using an indirect index, use TMP103_TEMP_REG directly to simplify the code.
Quoted 8 lines
drivers/hwmon/tmp103.c new file +8
-0+static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, tmp103_show_temp, + tmp103_set_temp, 1); + +static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, tmp103_show_temp, + tmp103_set_temp, 2); + +static struct attribute *tmp103_attrs[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr,
drivers/hwmon/tmp103.c line 152
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, +NULL +}; +ATTRIBUTE_GROUPS (tmp103); + +static struct regmap_config tmp103_regmap_config = { + .reg_bits =8 , + .val_bits =8 , + .max_register = TMP103_THIGH_REG,
You can also add a 'volatile' function to tell regmap which registers are volatile.
.volatile_reg = tmp103_is_volatile,
with
static bool tmp103_regmap_is_volatile(struct device *dev, unsigned int reg)
{
return reg == TMP103_TEMP_REG;
}With this, only the temperature register will be read after the first initialization. If you add alarm attributes, you'd have to add the configuration register, but not for now.
drivers/hwmon/tmp103.c line 156
Quoted 4 lines
drivers/hwmon/tmp103.c new file +4
-0+}; + +#define TMP103_CONFIG (TMP103_CONF_CR1 | TMP103_CONF_M1) +
Can you move this to the other definitions ? TMP103_CONF_SD is already there, so this would be more consistent.
Quoted 12 lines
drivers/hwmon/tmp103.c new file +12
-0+static int tmp103_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct device *dev = &client->dev; +struct device *hwmon_dev; +struct tmp103 *tmp103; +int ret; +unsigned int status; + +if (!i2c_check_functionality (client->adapter, +I2C_FUNC_SMBUS_BYTE_DATA )) { + dev_err(&client->dev,
drivers/hwmon/tmp103.c line 178
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ "adapter doesn't support SMBus byte transactions\n"); +return -ENODEV ; + } + + tmp103 =devm_kzalloc (&client->dev,sizeof (*tmp103),GFP_KERNEL ); +if (!tmp103) +return -ENOMEM ; + +i2c_set_clientdata (client, tmp103); + tmp103->client = client;
Both no longer needed.
Quoted 18 lines
drivers/hwmon/tmp103.c new file +18
-0+ + tmp103->regmap =devm_regmap_init_i2c (client, &tmp103_regmap_config); +if (IS_ERR (tmp103->regmap)) { +dev_err (dev,"failed to allocate register map\n" ); +return PTR_ERR (tmp103->regmap); + } + + ret =regmap_read (tmp103->regmap,TMP103_CONF_REG , &status); +if (ret <0 ) + goto fail_init_regmap; + + tmp103->config_orig = status; + ret =regmap_write (tmp103->regmap,TMP103_CONF_REG ,TMP103_CONFIG ); +if (ret <0 ) { +dev_err (&client->dev,"error writing config register\n" ); + goto fail_restore_config; + } +
drivers/hwmon/tmp103.c line 206
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ ret =regmap_read (tmp103->regmap,TMP103_CONF_REG , &status); +if (ret <0 ) { +dev_err (&client->dev,"error reading config register\n" ); + goto fail_restore_config; + } +if (status !=TMP103_CONFIG ) { +dev_err (&client->dev,"config settings did not stick\n" ); + ret = -ENODEV ; + goto fail_restore_config; + }
The above write/read sequence can be made conditional.
If (config_orig & 0x67) == TMP103_CONFIG, there is no need to update the configuration register.
Also, I just realized that the current code won't work: The FH and FL bits are not controlled by you, but by the chip. So the verification (as written) will fail if you have an alarm condition. I would suggest to drop the verification entirely; I don't think it adds much if any value. At the very least, you'll have to mask the result against 0x67.
Actually, I would suggest to drop config_orig entirely. Then you can use regmap_update_bits() to set the configuration. Also, you can then use devm_hwmon_device_register_with_groups(), and drop the remove function as well.
drivers/hwmon/tmp103.c line 207
Quoted 1 line
drivers/hwmon/tmp103.c new file +1
-0+ tmp103->last_update = jiffies -HZ ;
No longer needed.
Quoted 9 lines
drivers/hwmon/tmp103.c new file +7
-0+mutex_init (&tmp103->lock); + + hwmon_dev =hwmon_device_register_with_groups (dev, client->name, + tmp103, tmp103_groups); +if (IS_ERR (hwmon_dev)) { +dev_dbg (dev,"unable to register hwmon device\n" ); + status =PTR_ERR (hwmon_dev);
drivers/hwmon/tmp103.c line 224
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ goto fail_restore_config; + } + tmp103->hwmon_dev = hwmon_dev; + +return 0 ; + +fail_restore_config: +regmap_write (tmp103->regmap,TMP103_CONF_REG , tmp103->config_orig); +fail_init_regmap: +regmap_exit (tmp103->regmap);
This is not needed since you used the devm_ initialization function above. In fact, it is likely wrong.
If you drop restoring the configuration register, the entire sequence can become
hwmon_dev = devm_hwmon_device_register_with_groups(dev, client->name, tmp103, tmp103_groups); return PTR_ERR_OR_ZERO(hwmon_dev);
drivers/hwmon/tmp103.c line 234
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+return ret; +} + +static int tmp103_remove (struct i2c_client *client) +{ +struct tmp103 *tmp103 =i2c_get_clientdata (client); +int ret; + + ret =regmap_write (tmp103->regmap,TMP103_CONF_REG , + tmp103->config_orig);
Only needed if (config_orig & 0x67) != TMP103_CONFIG.
drivers/hwmon/tmp103.c line 196
Quoted 3 lines
drivers/hwmon/tmp103.c new file +3
-0+if (ret <0 ) +dev_err (&client->dev,"error writing config register\n" ); +
I'd suggest to drop the error message. It does not really matter, after all, and is quite unlikely.
Quoted 9 lines
drivers/hwmon/tmp103.c new file +9
-0+hwmon_device_unregister (tmp103->hwmon_dev); + +return 0 ; +} + +#ifdef CONFIG_PM +static int tmp103_suspend (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev);
drivers/hwmon/tmp103.c line 256
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+struct tmp103 *tmp103 =i2c_get_clientdata (client); +unsigned int config; +int ret; + + ret =regmap_read (tmp103->regmap,TMP103_CONF_REG , &config); +if (ret <0 ) +return ret; + + config &= ~TMP103_CONF_SD ; +return regmap_write (tmp103->regmap,TMP103_CONF_REG , config);
You can use regmap_update_bits() here.
Quoted 5 lines
drivers/hwmon/tmp103.c new file +5
-0+} + +static int tmp103_resume (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev);
drivers/hwmon/tmp103.c line 271
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+struct tmp103 *tmp103 =i2c_get_clientdata (client); +unsigned int config; +int ret; + + ret =regmap_read (tmp103->regmap,TMP103_CONF_REG , &config); +if (ret <0 ) +return ret; + + config |=TMP103_CONF_SD ; +return regmap_write (tmp103->regmap,TMP103_CONF_REG , config);
You can use regmap_update_bits() here.
Quoted 24 lines
drivers/hwmon/tmp103.c new file +23
-0+} + +static const struct dev_pm_ops tmp103_dev_pm_ops = { + .suspend = tmp103_suspend, + .resume = tmp103_resume, +}; + +#define TMP103_DEV_PM_OPS (&tmp103_dev_pm_ops) +#else +#define TMP103_DEV_PM_OPS NULL +#endif /* CONFIG_PM */ + +static const struct i2c_device_id tmp103_id[] = { + {DRIVER_NAME ,0 }, + { } +}; +MODULE_DEVICE_TABLE (i2c, tmp103_id); + +static struct i2c_driver tmp103_driver = { + .driver = { + .name =DRIVER_NAME , + .pm =TMP103_DEV_PM_OPS , + },
drivers/hwmon/tmp103.c line 304
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ .probe = tmp103_probe, + .remove = tmp103_remove, + .id_table = tmp103_id, +}; + +module_i2c_driver (tmp103_driver); + +MODULE_AUTHOR ("Heiko Schocher <[email protected]>" ); +MODULE_DESCRIPTION ("Texas Instruments TMP103 temperature sensor driver" ); +MODULE_LICENSE ("GPL" );
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html