hwmon: Driver for TI TMP103 temperature sensor
PATCH v4 1/1 hwmon: Driver for TI TMP103 temperature sensor
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
---
- change for v2:
- add comments from GuenterRoeck:
- remove Cc from commit subject
- add devicetree maintainer
- move Documentation to Documentation/hwmon/tmp103
- remove devicetree bindings from Documentation
- add compatible string to "Documentation/devicetree/bindings/i2c/trivial-devices.txt"
- remove CamelCase
- fix Codingstyle issues
- use ATTRIBUTE_GROUPS and devm_hwmon_device_register_with_groups()
- remove unsused define TMP103_CONFIG_RD_ONLY
- restore config register when exit()
- use regmap
- changes for v3:
again a lot of fantastic tips how to use regmap efficiently from Guenter Roeck:
- get rid of "struct tmp103"
- get rid of "static const u8 tmp103_reg[]"
- get rid of mutex lock
- drop config_orig entirely
- use regmap_update_bits()
- changes for v4:
- add comment from Guenter Roeck:
define TMP103_CONFIG_MASK and TMP103_CONF_SD_MASK separately to ensure you catch all the to-be-cleared bits.
.../devicetree/bindings/i2c/trivial-devices.txt | 1 + Documentation/hwmon/tmp103 | 28 +++ drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/tmp103.c | 207 +++++++++++++++++++++ 5 files changed, 247 insertions(+) create mode 100644 Documentation/hwmon/tmp103 create mode 100644 drivers/hwmon/tmp103.c
Documentation/devicetree/bindings/i2c/trivial-devices.txt +1 -0
@@ -83,5 +83,6 @@ stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor winbond,wpct301 i2c trusted platform module (TPM)
Documentation/hwmon/tmp103 new file +28 -0
@@ -0,0 +1,28 @@ +Kernel driver tmp103 +==================== + +Supported chips: + * Texas Instruments TMP103 + Prefix: 'tmp103' + Addresses scanned: none + Product info and datasheet: http://www.ti.com/product/tmp103 + +Author: + Heiko Schocher <[email protected]> + +Description +----------- + +The TMP103 is a digital output temperature sensor in a four-ball +wafer chip-scale package (WCSP). The TMP103 is capable of reading +temperatures to a resolution of 1°C. The TMP103 is specified for +operation over a temperature range of –40°C to +125°C. + +Resolution: 8 Bits +Accuracy: ±1°C Typ (–10°C to +100°C) + +The driver provides the common sysfs-interface for temperatures (see +Documentation/hwmon/sysfs-interface under Temperatures). + +Please refer how to instantiate this driver: +Documentation/i2c/instantiating-devices
drivers/hwmon/Kconfig +10 -0
@@ -1391,6 +1391,16 @@ config SENSORS_TMP102 This driver can also be built as a module. If so, the module will be called tmp102. +config SENSORS_TMP103 + tristate "Texas Instruments TMP103" + depends on I2C + help + If you say yes here you get support for Texas Instruments TMP103 + sensor chips. + + This driver can also be built as a module. If so, the module + will be called tmp103. + config SENSORS_TMP401 tristate "Texas Instruments TMP401 and compatibles" depends on I2C
drivers/hwmon/Makefile +1 -0
@@ -135,6 +135,7 @@ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o obj-$(CONFIG_SENSORS_TMP102) += tmp102.o +obj-$(CONFIG_SENSORS_TMP103) += tmp103.o obj-$(CONFIG_SENSORS_TMP401) += tmp401.o obj-$(CONFIG_SENSORS_TMP421) += tmp421.o obj-$(CONFIG_SENSORS_TWL4030_MADC)+= twl4030-madc-hwmon.o
drivers/hwmon/tmp103.c new file +207 -0
207 lines not on this page · raw message
Signature · 1 line
1.8.3.1
Guenter Roeck
maintainerQuoted 7 lines · Heiko Schocher
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
Signed-off-by Heiko Schocher <[email protected]>
[ ... ]
Quoted 1 line
+#define
TMP103_CONF_SD(TMP103_CONF_M0|TMP103_CONF_M1)
Hello Heiko,
I thought this needs to be TMP103_CONF_M1, but from the datasheet it looks like it does not matter if M0 is set if M1 is set as well. Did you test it, though, to make sure that it works ? I feel slightly uncomfortable with it.
Thanks,
Guenter
Hello Guenter
Am 17.06.2014 12:48, schrieb Guenter Roeck:
Quoted 8 lines · Heiko Schocher
Quoted 7 lines
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
Signed-off-by Heiko Schocher <[email protected]>
Quoted 8 lines
[ ... ]
Quoted 1 line
+#define
TMP103_CONF_SD(TMP103_CONF_M0|TMP103_CONF_M1)Hello Heiko,
I thought this needs to be
TMP103_CONF_M1, but from the datasheet it looks like it does not matter if M0 is set if M1 is set as well. Did you test it, though, to make sure that it works ? I feel slightly uncomfortable with it.
Yes, i tested it on an imx6 based board. I see no issues ... but I can test it with "#define TMP103_CONF_SD TMP103_CONF_M1" and post a v5 with this setting if it works ...
bye,
Heiko
Signature · 6 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Guenter Roeck
maintainerQuoted 16 lines · Heiko Schocher
Hello Guenter
Am 17.06.2014 12:48, schrieb Guenter Roeck:
Quoted 13 lines · Heiko Schocher
Quoted 7 lines
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
Signed-off-by Heiko Schocher <[email protected]>[ ... ]
Quoted 1 line
+#define
TMP103_CONF_SD(TMP103_CONF_M0|TMP103_CONF_M1)Hello Heiko,
Quoted 8 lines
Quoted 3 lines
I thought this needs to be
TMP103_CONF_M1, but from the datasheet it looks like it does not matter if M0 is set if M1 is set as well. Did you test it, though, to make sure that it works ? I feel slightly uncomfortable with it.Yes, i tested it on an imx6 based board. I see no issues ... but I can test it with "#define
TMP103_CONF_SDTMP103_CONF_M1" and post a v5 with this setting if it works ...
Hello Heiko,
I would appreciate that.
Thanks,
Guenter
Quoted 314 lines · Heiko Schocher
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
Signed-off-by Heiko Schocher <[email protected]>---
Cc Jean Delvare <[email protected]>Cc Guenter Roeck <[email protected]>- change for v2:
- add comments from GuenterRoeck:
- remove Cc from commit subject
- add devicetree maintainer
- move Documentation toDocumentation/hwmon/tmp103
- remove devicetree bindings from Documentation
- add compatible string to "Documentation/devicetree/bindings/i2c/trivial-devices.txt"
- remove CamelCase
- fix Codingstyle issues
- useATTRIBUTE_GROUPSanddevm_hwmon_device_register_with_groups()
- remove unsused defineTMP103_CONFIG_RD_ONLY
- restore config register whenexit()
- use regmap
- changes for v3:
again a lot of fantastic tips how to use regmap efficiently from Guenter Roeck:
- get rid of "struct tmp103"
- get rid of "static const u8 tmp103_reg[]"
- get rid of mutex lock
- dropconfig_origentirely
- useregmap_update_bits()
- changes for v4:
- add comment from Guenter Roeck:
defineTMP103_CONFIG_MASKandTMP103_CONF_SD_MASKseparately to ensure you catch all the to-be-cleared bits..../devicetree/bindings/i2c/trivial-devices.txt | 1 + Documentation/hwmon/tmp103 | 28 +++ drivers/hwmon/Kconfig | 10 + drivers/hwmon/Makefile | 1 + drivers/hwmon/tmp103.c | 207 +++++++++++++++++++++ 5 files changed, 247 insertions(+) create mode 100644 Documentation/hwmon/tmp103 create mode 100644 drivers/hwmon/tmp103.cDocumentation/devicetree/bindings/i2c/trivial-devices.txt +1
-0@@ -83,5 +83,6 @@ stm,m41t80 M41T80 - SERIAL ACCESS RTC WITH ALARMS taos,tsl2550 Ambient Light Sensor with SMBUS/Two Wire Serial Interface ti,tsc2003 I2C Touch-Screen Controller ti,tmp102 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface +ti,tmp103 Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface ti,tmp275 Digital Temperature Sensor winbond,wpct301 i2c trusted platform module (TPM)Documentation/hwmon/tmp103 new file +28
-0@@ -0,0 +1,28 @@ +Kernel driver tmp103 +==================== + +Supported chips: + * Texas Instruments TMP103 + Prefix: 'tmp103' + Addresses scanned: none + Product info and datasheet: http://www.ti.com/product/tmp103 + +Author: + Heiko Schocher <[email protected]> + +Description +----------- + +The TMP103 is a digital output temperature sensor in a four-ball +wafer chip-scale package (WCSP). The TMP103 is capable of reading +temperatures to a resolution of 1°C. The TMP103 is specified for +operation over a temperature range of –40°C to +125°C. + +Resolution: 8 Bits +Accuracy: ±1°C Typ (–10°C to +100°C) + +The driver provides the common sysfs-interface for temperatures (see +Documentation/hwmon/sysfs-interface under Temperatures). + +Please refer how to instantiate this driver: +Documentation/i2c/instantiating-devicesdrivers/hwmon/Kconfig +10
-0@@ -1391,6 +1391,16 @@ config SENSORS_TMP102 This driver can also be built as a module. If so, the module will be called tmp102. +config SENSORS_TMP103 + tristate "Texas Instruments TMP103" + depends on I2C + help + If you say yes here you get support for Texas Instruments TMP103 + sensor chips. + + This driver can also be built as a module. If so, the module + will be called tmp103. + config SENSORS_TMP401 tristate "Texas Instruments TMP401 and compatibles" depends on I2Cdrivers/hwmon/Makefile +1
-0@@ -135,6 +135,7 @@ obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o obj-$(CONFIG_SENSORS_AMC6821) += amc6821.o obj-$(CONFIG_SENSORS_THMC50) += thmc50.o obj-$(CONFIG_SENSORS_TMP102) += tmp102.o +obj-$(CONFIG_SENSORS_TMP103) += tmp103.o obj-$(CONFIG_SENSORS_TMP401) += tmp401.o obj-$(CONFIG_SENSORS_TMP421) += tmp421.o obj-$(CONFIG_SENSORS_TWL4030_MADC)+= twl4030-madc-hwmon.odrivers/hwmon/tmp103.c new file +179
-0@@ -0,0 +1,207 @@ +/* +* Texas Instruments TMP103 SMBus temperature sensor driver +* Copyright (C) 2014 Heiko Schocher <[email protected]> +* +* Based on: +* Texas Instruments TMP102 SMBus temperature sensor driver +* +* Copyright (C) 2010 Steven King <[email protected]> +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; either version 2 of the License, or +* (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/err.h> +#include <linux/mutex.h> +#include <linux/device.h> +#include <linux/jiffies.h> +#include <linux/regmap.h> + +#define DRIVER_NAME "tmp103" + +#define TMP103_TEMP_REG 0x00 +#define TMP103_CONF_REG 0x01 +#define TMP103_TLOW_REG 0x02 +#define TMP103_THIGH_REG 0x03 + +#define TMP103_CONF_M0 0x01 +#define TMP103_CONF_M1 0x02 +#define TMP103_CONF_LC 0x04 +#define TMP103_CONF_FL 0x08 +#define TMP103_CONF_FH 0x10 +#define TMP103_CONF_CR0 0x20 +#define TMP103_CONF_CR1 0x40 +#define TMP103_CONF_ID 0x80 +#define TMP103_CONF_SD (TMP103_CONF_M0 | TMP103_CONF_M1) +#define TMP103_CONF_SD_MASK (TMP103_CONF_M0 | TMP103_CONF_M1) + +#define TMP103_CONFIG (TMP103_CONF_CR1 | TMP103_CONF_M1) +#define TMP103_CONFIG_MASK (TMP103_CONF_CR0 | TMP103_CONF_CR1 | \ + TMP103_CONF_M0 | TMP103_CONF_M1) + +static inline int tmp103_reg_to_mc (s8 val) +{ +return val *1000 ; +} + +static inline u8 tmp103_mc_to_reg (int val) +{ +return DIV_ROUND_CLOSEST (val,1000 ); +} + +static ssize_t tmp103_show_temp (struct device *dev, +struct device_attribute *attr, +char *buf) +{ +struct sensor_device_attribute *sda =to_sensor_dev_attr (attr); +struct regmap *regmap =dev_get_drvdata (dev); +unsigned int regval; +int ret; + + ret =regmap_read (regmap, sda->index, ®val); +if (ret <0 ) +return ret; + +return sprintf (buf,"%d\n" ,tmp103_reg_to_mc (regval)); +} + +static ssize_t tmp103_set_temp (struct device *dev, +struct device_attribute *attr, +const char *buf,size_t count) +{ +struct sensor_device_attribute *sda =to_sensor_dev_attr (attr); +struct regmap *regmap =dev_get_drvdata (dev); +long val; +int ret; + +if (kstrtol (buf,10 , &val) <0 ) +return -EINVAL ; + + val =clamp_val (val,-55000 ,127000 ); + ret =regmap_write (regmap, sda->index,tmp103_mc_to_reg (val)); +return ret ? ret : count; +} + +static SENSOR_DEVICE_ATTR(temp1_input, S_IRUGO, tmp103_show_temp, NULL , + TMP103_TEMP_REG); + +static SENSOR_DEVICE_ATTR(temp1_min, S_IWUSR | S_IRUGO, tmp103_show_temp, + tmp103_set_temp, TMP103_TLOW_REG); + +static SENSOR_DEVICE_ATTR(temp1_max, S_IWUSR | S_IRUGO, tmp103_show_temp, + tmp103_set_temp, TMP103_THIGH_REG); + +static struct attribute *tmp103_attrs[] = { + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, +NULL +}; +ATTRIBUTE_GROUPS (tmp103); + +static bool tmp103_regmap_is_volatile (struct device *dev,unsigned int reg) +{ +return reg ==TMP103_TEMP_REG ; +} + +static struct regmap_config tmp103_regmap_config = { + .reg_bits =8 , + .val_bits =8 , + .max_register =TMP103_THIGH_REG , + .volatile_reg = tmp103_regmap_is_volatile, +}; + +static int tmp103_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct device *dev = &client->dev; +struct device *hwmon_dev; +struct regmap *regmap; +int ret; + +if (!i2c_check_functionality (client->adapter, +I2C_FUNC_SMBUS_BYTE_DATA )) { +dev_err (&client->dev, +"adapter doesn't support SMBus byte transactions\n" ); +return -ENODEV ; + } + + regmap =devm_regmap_init_i2c (client, &tmp103_regmap_config); +if (IS_ERR (regmap)) { +dev_err (dev,"failed to allocate register map\n" ); +return PTR_ERR (regmap); + } + + ret =regmap_update_bits (regmap,TMP103_CONF_REG ,TMP103_CONFIG_MASK , +TMP103_CONFIG ); +if (ret <0 ) { +dev_err (&client->dev,"error writing config register\n" ); +return ret; + } + + hwmon_dev =hwmon_device_register_with_groups (dev, client->name, + regmap, tmp103_groups); +return PTR_ERR_OR_ZERO (hwmon_dev); +} + +#ifdef CONFIG_PM +static int tmp103_suspend (struct device *dev) +{ +struct regmap *regmap =dev_get_drvdata (dev); + +return regmap_update_bits (regmap,TMP103_CONF_REG , +TMP103_CONF_SD_MASK ,0 ); +} + +static int tmp103_resume (struct device *dev) +{ +struct regmap *regmap =dev_get_drvdata (dev); + +return regmap_update_bits (regmap,TMP103_CONF_REG , +TMP103_CONF_SD_MASK ,TMP103_CONF_SD ); +} + +static const struct dev_pm_ops tmp103_dev_pm_ops = { + .suspend = tmp103_suspend,
drivers/hwmon/tmp103.c line 189
Quoted 10 lines
drivers/hwmon/tmp103.c new file +10
-0+ .resume = tmp103_resume, +}; + +#define TMP103_DEV_PM_OPS (&tmp103_dev_pm_ops) +#else +#define TMP103_DEV_PM_OPS NULL +#endif /* CONFIG_PM */ + +static const struct i2c_device_id tmp103_id[] = { + {DRIVER_NAME ,0 },
This seems to be used for compatible string matching. As such, I think it would make more sense to have the string in full here so as to discourage it from being changed arbitrarily in future.
Otherwise, the dt part looks fine by me.
Cheers,
Mark.
Guenter Roeck
maintainerQuoted 8 lines · Mark Rutland
Quoted 7 lines · Heiko Schocher
Driver for the TI TMP103.
The TI TMP103 is similar to the TMP102. It differs from the TMP102 by having only 8 bit registers.
Signed-off-by Heiko Schocher <[email protected]>
[ ... ]
Quoted 8 lines
drivers/hwmon/tmp103.c line 189
Quoted 3 lines
drivers/hwmon/tmp103.c new file +3
-0+ +static const struct i2c_device_id tmp103_id[] = { + {DRIVER_NAME ,0 },This seems to be used for compatible string matching. As such, I think it would make more sense to have the string in full here so as to discourage it from being changed arbitrarily in future.
Makes sense. Heiko, can you change that as well in v5 ? It also simplifies adding another chip to the driver, should that ever happen.
Thanks,
Guenter