Skip to contentSkip to conversation

drm/i915: DPI FIFO empty check is not needed

PATCH In review Shobhit Kumar 3 participants 4 messages Jul 3, 2014 – Jul 4, 2014

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 drm/i915: DPI FIFO empty check is not needed

While sending DPI SHUTDOWN command, we cannot wait for FIFO empty as pipes are not disabled at that time. In case of MIPI we disable port first and send SHUTDOWN command while pipe is still running and FIFOs will not be empty, causing spurious error log

---
 drivers/gpu/drm/i915/intel_dsi_cmd.c | 6 ------
 1 file changed, 6 deletions(-)
drivers/gpu/drm/i915/intel_dsi_cmd.c +0 -6
index 3eeb21b..933c863 100644
@@ -404,12 +404,6 @@ int dpi_send_cmd(struct intel_dsi *intel_dsi, u32 cmd, bool hs)
 	else
 		cmd |= DPI_LP_MODE;
 
-	/* DPI virtual channel?! */
-
-	mask = DPI_FIFO_EMPTY;
-	if (wait_for((I915_READ(MIPI_GEN_FIFO_STAT(pipe)) & mask) == mask, 50))
-		DRM_ERROR("Timeout waiting for DPI FIFO empty.\n");
-
 	/* clear bit */
 	I915_WRITE(MIPI_INTR_STAT(pipe), SPL_PKT_SENT_INTERRUPT);
 
Signature · 1 line
1.9.1
#1 lore raw

PATCH 2/2 drm/i915: Update the DSI ULPS entry/exit sequence

We should keep DEVICE_READY bit set in the ULPS enter sequence. In exit sequence also we should set DEVICE_READY, but thats causing blankout for me. Also exit sequence is simplified as per hw team recommendation.

This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818

---
 drivers/gpu/drm/i915/intel_dsi.c | 29 +++++++++++++++--------------
 1 file changed, 15 insertions(+), 14 deletions(-)
drivers/gpu/drm/i915/intel_dsi.c +15 -14
index a6a1355..967a5b6 100644
@@ -117,17 +117,18 @@ static void intel_dsi_device_ready(struct intel_encoder *encoder)
 	/* bandgap reset is needed after everytime we do power gate */
 	band_gap_reset(dev_priv);
 
+	I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_ENTER);
+	usleep_range(2500, 3000);
+
 	val = I915_READ(MIPI_PORT_CTRL(pipe));
 	I915_WRITE(MIPI_PORT_CTRL(pipe), val | LP_OUTPUT_HOLD);
 	usleep_range(1000, 1500);
-	I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY | ULPS_STATE_EXIT);
-	usleep_range(2000, 2500);
-	I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY);
-	usleep_range(2000, 2500);
-	I915_WRITE(MIPI_DEVICE_READY(pipe), 0x00);
-	usleep_range(2000, 2500);
+
+	I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_EXIT);
+	usleep_range(2500, 3000);
+
 	I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY);
-	usleep_range(2000, 2500);
+	usleep_range(2500, 3000);
 }
 
 static void intel_dsi_enable(struct intel_encoder *encoder)
@@ -271,23 +272,23 @@ static void intel_dsi_clear_device_ready(struct intel_encoder *encoder)
 
 	DRM_DEBUG_KMS("\n");
 
-	I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_ENTER);
+	I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY | ULPS_STATE_ENTER);
 	usleep_range(2000, 2500);
 
-	I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_EXIT);
+	I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY | ULPS_STATE_EXIT);
 	usleep_range(2000, 2500);
 
-	I915_WRITE(MIPI_DEVICE_READY(pipe), ULPS_STATE_ENTER);
+	I915_WRITE(MIPI_DEVICE_READY(pipe), DEVICE_READY | ULPS_STATE_ENTER);
 	usleep_range(2000, 2500);
 
-	val = I915_READ(MIPI_PORT_CTRL(pipe));
-	I915_WRITE(MIPI_PORT_CTRL(pipe), val & ~LP_OUTPUT_HOLD);
-	usleep_range(1000, 1500);
-
 	if (wait_for(((I915_READ(MIPI_PORT_CTRL(pipe)) & AFE_LATCHOUT)
 					== 0x00000), 30))
 		DRM_ERROR("DSI LP not going Low\n");
 
+	val = I915_READ(MIPI_PORT_CTRL(pipe));
+	I915_WRITE(MIPI_PORT_CTRL(pipe), val & ~LP_OUTPUT_HOLD);
+	usleep_range(1000, 1500);
+
 	I915_WRITE(MIPI_DEVICE_READY(pipe), 0x00);
 	usleep_range(2000, 2500);
 
Signature · 1 line
1.9.1
Tested-by on v1 2/2
#2 lore raw

Re: [PATCH 2/2] drm/i915: Update the DSI ULPS entry/exit sequence

Quoted 10 lines · Shobhit Kumar

We should keep DEVICE_READY bit set in the ULPS enter sequence. In exit sequence also we should set DEVICE_READY, but thats causing blankout for me. Also exit sequence is simplified as per hw team recommendation.

This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818

They silence that warning and appears to still work,

-Chris

Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre
#3 lore raw

Re: [PATCH 2/2] drm/i915: Update the DSI ULPS entry/exit sequence

Quoted 6 lines · Chris Wilson
Quoted 5 lines · Shobhit Kumar

We should keep DEVICE_READY bit set in the ULPS enter sequence. In exit sequence also we should set DEVICE_READY, but thats causing blankout for me. Also exit sequence is simplified as per hw team recommendation.

Quoted 8 lines
Quoted 5 lines

This should fix -
[drm:intel_dsi_clear_device_ready] *ERROR* DSI LP not going Low

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80818

They silence that warning and appears to still work,

Pushed to -fixes, thanks for the patches and testing.

BR,
Jani.

Quoted 4 lines

-Chris

Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre
Signature · 1 line
Jani Nikula, Intel Open Source Technology Center