pci: iproc: Add Broadcom iProc PCIe support
Subsystems (4)
Ray Jui
maintainerv7 cover pci: iproc: Add Broadcom iProc PCIe support
This patch series adds the support for Broadcom iProc PCIe controller
pcie-iproc.c servers as the common core driver, and front-end bus interface needs to be added to support different bus interfaces
pcie-iproc-pltfm.c contains the support for the platform bus interface
Changes from v6:
- Fix print formatting
- Fix section mismatch warning by removing __init from the probe function
- Fix Kconfig to force it only compiling for ARM based platforms
Changes from v5:
- Sync code base to v4.0-rc2
- Change export symbols of common PCI functions to GPL only
- Add comment to describe how configuration register access are protected at the higher layer through 'pci_lock'
- Use generic PCI functions for configuration register access and implement 'map_bus' callback to support it
- Move 'pci_fixup_irqs' to before devices are added to the bus
- Remove 'extern' from function prototype declared in the header
Changes from v4:
- iProc PCIe driver module support was not included in patch series v4. This patch series (v5) fixes it
Changes from v3:
- Export symbols of several PCI functions so they can be used by drivers compiled as kernel module
- Add additional support to the Broadcom iProc PCIe driver so it can be installed/uninstalled as kernel loadable module
Changes from v2:
- Major rework of the PCIe driver to factor out common generic code from front-end bus interface. Support for generic platform bus interface is also added
- Adapt to several new PCI APIs that have been introduced lately
Changes from v1:
- Add standard PCI interrupt DT properties "#interrupt-cells", "interrupt-map-mask" and "interrupt-map" so legacy INTx interrupts can be supported by using standard PCI OF IRQ parsing function
- Get rid of custom IRQ mapping function in the driver. Use of_irq_parse_and_map_pci instead
Ray Jui (4):
PCI: Export symbols of PCI functions
pci: iProc: define iProc PCIe platform bus binding
pci: iproc: Add Broadcom iProc PCIe support
ARM: dts: enable PCIe support for Cygnus
.../devicetree/bindings/pci/brcm,iproc-pcie.txt | 63 +++++ arch/arm/boot/dts/bcm-cygnus.dtsi | 42 +++ arch/arm/boot/dts/bcm958300k.dts | 8 + drivers/pci/host/Kconfig | 17 ++ drivers/pci/host/Makefile | 2 + drivers/pci/host/pcie-iproc-pltfm.c | 108 ++++++++ drivers/pci/host/pcie-iproc.c | 268 ++++++++++++++++++++ drivers/pci/host/pcie-iproc.h | 42 +++ drivers/pci/pci.c | 1 + drivers/pci/probe.c | 1 + drivers/pci/remove.c | 2 + drivers/pci/setup-bus.c | 1 + drivers/pci/setup-irq.c | 1 + 13 files changed, 556 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c create mode 100644 drivers/pci/host/pcie-iproc.c create mode 100644 drivers/pci/host/pcie-iproc.h
Signature · 1 line
1.7.9.5
Ray Jui
maintainerPATCH v7 1/4 PCI: Export symbols of PCI functions
Export symbols of the following PCI functions so they can be referenced by a PCI driver compiled as a kernel loadable module:
pci_common_swizzlepci_create_root_buspci_stop_root_buspci_remove_root_buspci_assign_unassigned_bus_resourcespci_fixup_irqs
--- drivers/pci/pci.c | 1 + drivers/pci/probe.c | 1 + drivers/pci/remove.c | 2 ++ drivers/pci/setup-bus.c | 1 + drivers/pci/setup-irq.c | 1 + 5 files changed, 6 insertions(+)
drivers/pci/pci.c +1 -0
@@ -2492,6 +2492,7 @@ u8 pci_common_swizzle(struct pci_dev *dev, u8 *pinp) *pinp = pin;return PCI_SLOT (dev->devfn); } +EXPORT_SYMBOL_GPL (pci_common_swizzle);/** * pci_release_region - Release a PCI bar
drivers/pci/probe.c +1 -0
@@ -1993,6 +1993,7 @@ err_out:kfree (b);return NULL ; } +EXPORT_SYMBOL_GPL (pci_create_root_bus);int pci_bus_insert_busn_res (struct pci_bus *b,int bus,int bus_max) {
drivers/pci/remove.c +2 -0
@@ -139,6 +139,7 @@ void pci_stop_root_bus(struct pci_bus *bus)/* stop the host bridge */ device_release_driver (&host_bridge->dev); } +EXPORT_SYMBOL_GPL (pci_stop_root_bus);void pci_remove_root_bus (struct pci_bus *bus) {
@@ -158,3 +159,4 @@ void pci_remove_root_bus(struct pci_bus *bus)/* remove the host bridge */ device_unregister (&host_bridge->dev); } +EXPORT_SYMBOL_GPL (pci_remove_root_bus);
drivers/pci/setup-bus.c +1 -0
@@ -1750,3 +1750,4 @@ void pci_assign_unassigned_bus_resources(struct pci_bus *bus)__pci_bus_assign_resources (bus, &add_list,NULL );BUG_ON (!list_empty (&add_list)); } +EXPORT_SYMBOL_GPL (pci_assign_unassigned_bus_resources);
drivers/pci/setup-irq.c +1 -0
@@ -65,3 +65,4 @@ void pci_fixup_irqs(u8 (*swizzle)(struct pci_dev *, u8 *),for_each_pci_dev (dev)pdev_fixup_irq (dev, swizzle, map_irq); } +EXPORT_SYMBOL_GPL (pci_fixup_irqs);
Signature · 1 line
1.7.9.5
Ray Jui
maintainerPATCH v7 2/4 pci: iProc: define iProc PCIe platform bus binding
In reply to Ray JuiDocument the Broadcom iProc PCIe platform interface device tree binding
--- .../devicetree/bindings/pci/brcm,iproc-pcie.txt | 63 ++++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt
Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt new file +63 -0
@@ -0,0 +1,63 @@ +* Broadcom iProc PCIe controller with the platform bus interface + +Required properties: +- compatible: Must be "brcm,iproc-pcie" +- reg: base address and length of the PCIe controller I/O register space +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map, standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers +- linux,pci-domain: PCI domain ID. Should be unique for each host controller +- bus-range: PCI bus numbers covered +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions + +Optional properties: +- phys: phandle of the PCIe PHY device +- phy-names: must be "pcie-phy" + +Example: + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + phys = <&phy 0 5>; + phy-names = "pcie-phy"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + phys = <&phy 1 6>; + phy-names = "pcie-phy"; + };
Signature · 1 line
1.7.9.5
Ray Jui
maintainerPATCH v7 3/4 pci: iproc: Add Broadcom iProc PCIe support
In reply to Ray JuiThis adds the support for Broadcom iProc PCIe controller
pcie-iproc.c servers as the common core driver, and front-end bus interface needs to be added to support different bus interfaces
pcie-iproc-pltfm.c contains the support for the platform bus interface
--- drivers/pci/host/Kconfig | 17 +++ drivers/pci/host/Makefile | 2 + drivers/pci/host/pcie-iproc-pltfm.c | 108 ++++++++++++++ drivers/pci/host/pcie-iproc.c | 268 +++++++++++++++++++++++++++++++++++ drivers/pci/host/pcie-iproc.h | 42 ++++++ 5 files changed, 437 insertions(+) create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c create mode 100644 drivers/pci/host/pcie-iproc.c create mode 100644 drivers/pci/host/pcie-iproc.h
drivers/pci/host/Kconfig +17 -0
@@ -106,4 +106,21 @@ config PCI_VERSATILE bool "ARM Versatile PB PCI controller" depends on ARCH_VERSATILE +config PCIE_IPROC + tristate "Broadcom iProc PCIe controller" + help + This enables the iProc PCIe core controller support for Broadcom's + iProc family of SoCs. An appropriate bus interface driver also needs + to be enabled + +config PCIE_IPROC_PLTFM + tristate "Broadcom iProc PCIe platform bus driver" + depends on ARCH_BCM_IPROC || (ARM && COMPILE_TEST) + depends on OF + select PCIE_IPROC + default ARCH_BCM_IPROC + help + Say Y here if you want to use the Broadcom iProc PCIe controller + through the generic platform bus interface + endmenu
drivers/pci/host/Makefile +2 -0
@@ -13,3 +13,5 @@ obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o obj-$(CONFIG_PCI_XGENE) += pci-xgene.o obj-$(CONFIG_PCI_LAYERSCAPE) += pci-layerscape.o obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o +obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o +obj-$(CONFIG_PCIE_IPROC_PLTFM) += pcie-iproc-pltfm.o
drivers/pci/host/pcie-iproc-pltfm.c new file +108 -0
108 lines not on this page · raw message
drivers/pci/host/pcie-iproc.c new file +268 -0
268 lines not on this page · raw message
drivers/pci/host/pcie-iproc.h new file +42 -0
42 lines not on this page · raw message
Signature · 1 line
1.7.9.5
Ray Jui
maintainerPATCH v7 4/4 ARM: dts: enable PCIe support for Cygnus
In reply to Ray JuiAdd PCIe device nodes in bcm-cygnus.dtsi but keep them disabled there. Only enable them for bcm958300k where PCIe interfaces are populated
--- arch/arm/boot/dts/bcm-cygnus.dtsi | 42 +++++++++++++++++++++++++++++++++++++ arch/arm/boot/dts/bcm958300k.dts | 8 +++++++ 2 files changed, 50 insertions(+)
arch/arm/boot/dts/bcm-cygnus.dtsi +42 -0
@@ -90,6 +90,48 @@ status = "disabled"; }; + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + status = "disabled"; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + status = "disabled"; + }; + uart0: serial@18020000 { compatible = "snps,dw-apb-uart"; reg = <0x18020000 0x100>;
arch/arm/boot/dts/bcm958300k.dts +8 -0
@@ -47,6 +47,14 @@ bootargs = "console=ttyS0,115200"; }; + pcie0: pcie@18012000 { + status = "okay"; + }; + + pcie1: pcie@18013000 { + status = "okay"; + }; + uart3: serial@18023000 { status = "okay"; };
Signature · 1 line
1.7.9.5
[+cc Florian]
Quoted 45 lines · Ray Jui
This patch series adds the support for Broadcom iProc PCIe controller
pcie-iproc.cservers as the common core driver, and front-end bus interface needs to be added to support different bus interfaces
pcie-iproc-pltfm.ccontains the support for the platform bus interfaceChanges from v6:
- Fix print formatting
- Fix section mismatch warning by removing__initfrom the probe function
- FixKconfigto force it only compiling for ARM based platformsChanges from v5:
- Sync code base to v4.0-rc2
- Change export symbols of common PCI functions to GPL only
- Add comment to describe how configuration register access are protected at the higher layer through 'pci_lock'
- Use generic PCI functions for configuration register access and implement 'map_bus' callback to support it
- Move 'pci_fixup_irqs' to before devices are added to the bus
- Remove 'extern' from function prototype declared in the headerChanges from v4:
- iProc PCIe driver module support was not included in patch series v4. This patch series (v5) fixes itChanges from v3:
- Export symbols of several PCI functions so they can be used by drivers compiled as kernel module
- Add additional support to the Broadcom iProc PCIe driver so it can be installed/uninstalled as kernel loadable moduleChanges from v2:
- Major rework of the PCIe driver to factor out common generic code from front-end bus interface. Support for generic platform bus interface is also added
- Adapt to several new PCI APIs that have been introduced latelyChanges from v1:
- Add standard PCI interrupt DT properties "#interrupt-cells", "interrupt-map-mask" and "interrupt-map" so legacy INTx interrupts can be supported by using standard PCI OF IRQ parsing function
- Get rid of custom IRQ mapping function in the driver. Useof_irq_parse_and_map_pciinstead
Quoted 5 lines
Ray Jui (4):
PCI: Export symbols of PCI functions
pci: iProc: define iProc PCIe platform bus binding
pci: iproc: Add Broadcom iProc PCIe support
ARM: dts: enable PCIe support for Cygnus
I applied patches 1-3 to pci/host-iproc for v4.1, thanks! I didn't apply patch 4 because Florian said he'd already applied it to devicetree/next.
I normally look for a MAINTAINERS entry, but your existing entry for "BROADCOM CYGNUS/IPROC ARM ARCHITECTURE" has wildcards that already include these new files.
Quoted 22 lines
.../devicetree/bindings/pci/brcm,iproc-pcie.txt | 63 +++++ arch/arm/boot/dts/bcm-cygnus.dtsi | 42 +++ arch/arm/boot/dts/bcm958300k.dts | 8 + drivers/pci/host/Kconfig | 17 ++ drivers/pci/host/Makefile | 2 + drivers/pci/host/pcie-iproc-pltfm.c | 108 ++++++++ drivers/pci/host/pcie-iproc.c | 268 ++++++++++++++++++++ drivers/pci/host/pcie-iproc.h | 42 +++ drivers/pci/pci.c | 1 + drivers/pci/probe.c | 1 + drivers/pci/remove.c | 2 + drivers/pci/setup-bus.c | 1 + drivers/pci/setup-irq.c | 1 + 13 files changed, 556 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt create mode 100644 drivers/pci/host/pcie-iproc-pltfm.c create mode 100644 drivers/pci/host/pcie-iproc.c create mode 100644 drivers/pci/host/pcie-iproc.hSignature · 1 line
1.7.9.5