MIPS: barebox as a first stage loader on the Black Swift board
Subsystems (3)
v2 cover MIPS: barebox as a first stage loader on the Black Swift board
This patchseries adds necessary AR9331 SoC low level initialization routines. The patchseries makes it possible to use barebox as a first stage loader on the Black Swift board and, I suppose, other widespread AR9331-based boards.
The patchseries is heavily based on Oleksij Rempel's work on barebox for TP-Link MR3020.
TODOs:
* add TP-Link MR3020 support (see http://openocd.zylin.com/gitweb?p=openocd.git;a=commitdiff;h=f59d2d9ecfee8899df531b87b7acaa468725f238);
* clean up Black Swift GPIO code (pbl_reg_set (1 << 18), 0xb80600ac);
* check macros names linux kernel source compartibility;
* DT compatible string vendor "smartlx" appears un-documented.
The site http://www.smartlx.ru/ is suspended.
Changes since RFC v1:
* add UART initialization routune for DEBUG_LL and NMON;
* add macros for GPIO_FUNCTION_1 register initialization;
* add ar71xx GPIO driver.
Antony Pavlov (9):
MIPS: ar933x: pbl: add pbl_ar9331_ddr2_config macro
MIPS: mach-ath79: add pbl_ar9331_uart_enable macro
MIPS: mach-ath79: add debug_ll_ar9331_init macro
MIPS: ath79: add black-swift board support
MIPS: add black-swift_defconfig
gpio: add ath79-gpio driver for Atheros MIPS SoCs
MIPS: ath79: use gpiolib
MIPS: dts: ar9331.dtsi: add gpio
WIP: MIPS: black-swift: use GPIO
Oleksij Rempel (1):
MIPS: ar933x: pbl: add pbl_ar9331_pll macro
arch/mips/Kconfig | 1 + arch/mips/Makefile | 1 + arch/mips/boards/black-swift/Makefile | 1 + arch/mips/boards/black-swift/board.c | 27 ++++ .../black-swift/include/board/board_pbl_start.h | 41 ++++++ arch/mips/boot/start.S | 2 + arch/mips/configs/black-swift_defconfig | 45 +++++++ arch/mips/dts/ar9331.dtsi | 10 ++ arch/mips/dts/black-swift.dts | 60 +++++++++ arch/mips/include/asm/pbl_macros.h | 32 +++++ arch/mips/mach-ath79/Kconfig | 6 + arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 41 ++++++ arch/mips/mach-ath79/include/mach/debug_ll.h | 29 ++++ arch/mips/mach-ath79/include/mach/pbl_macros.h | 139 ++++++++++++++++++++ drivers/gpio/Makefile | 1 + drivers/gpio/gpio-ath79.c | 146 +++++++++++++++++++++ 16 files changed, 582 insertions(+) create mode 100644 arch/mips/boards/black-swift/Makefile create mode 100644 arch/mips/boards/black-swift/board.c create mode 100644 arch/mips/boards/black-swift/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/black-swift_defconfig create mode 100644 arch/mips/dts/black-swift.dts create mode 100644 arch/mips/mach-ath79/include/mach/pbl_macros.h create mode 100644 drivers/gpio/gpio-ath79.c
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 1/10 MIPS: ar933x: pbl: add pbl_ar9331_pll macro
From: Oleksij Rempel <[email protected]>
--- arch/mips/include/asm/pbl_macros.h | 21 ++++++++++++ arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 1 + arch/mips/mach-ath79/include/mach/pbl_macros.h | 43 +++++++++++++++++++++++++ 3 files changed, 65 insertions(+)
arch/mips/include/asm/pbl_macros.h +21 -0
@@ -28,6 +28,27 @@#include <generated/compile.h> #include <generated/utsrelease.h> + .macro pbl_reg_writel val addr + .set push + .set noreorder + li t9, \addr + li t8, \val + sw t8, 0(t9) + .set pop + .endm + + .macro pbl_reg_clr clr addr + .set push + .set noreorder + li t9, \addr + li t8, \clr + lw t7, 0(t9) + not t8, t8 + and t7, t8 + sw t7, 0(t9) + .set pop + .endm + .macro pbl_sleep reg count .set push .set noreorder
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +1 -0
@@ -46,6 +46,7 @@#define AR933X_PLL_CPU_CONFIG_REFDIV_MASK 0x1f#define AR933X_PLL_CPU_CONFIG_OUTDIV_SHIFT 23#define AR933X_PLL_CPU_CONFIG_OUTDIV_MASK 0x7 +#define AR933X_PLL_CPU_CONFIG_PLLPWD BIT(30)#define AR933X_PLL_CLOCK_CTRL_BYPASS BIT(2)#define AR933X_PLL_CLOCK_CTRL_CPU_DIV_SHIFT 5
arch/mips/mach-ath79/include/mach/pbl_macros.h new file +43 -0
43 lines not on this page · raw message
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 2/10 MIPS: ar933x: pbl: add pbl_ar9331_ddr2_config macro
In reply to Antony Pavlov--- arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 20 ++++++ arch/mips/mach-ath79/include/mach/pbl_macros.h | 89 +++++++++++++++++++++++++ 2 files changed, 109 insertions(+)
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +20 -0
@@ -23,6 +23,8 @@#define AR71XX_APB_BASE 0x18000000 +#define AR71XX_DDR_CTRL_BASE (AR71XX_APB_BASE + 0x00000000) +#define AR71XX_DDR_CTRL_SIZE 0x100#define AR71XX_PLL_BASE (AR71XX_APB_BASE + 0x00050000)#define AR71XX_PLL_SIZE 0x100#define AR71XX_RESET_BASE (AR71XX_APB_BASE + 0x00060000)
@@ -32,6 +34,24 @@#define AR933X_UART_SIZE 0x14/* +* DDR_CTRL block +*/ +#define AR933X_DDR_CONFIG 0x00 +#define AR933X_DDR_CONFIG2 0x04 +#define AR933X_DDR_MODE 0x08 +#define AR933X_DDR_EXT_MODE 0x0c +#define AR933X_DDR_CTRL 0x10 +#define AR933X_DDR_REFRESH 0x14 +#define AR933X_DDR_RD_DATA 0x18 +#define AR933X_DDR_TAP_CTRL0 0x1c +#define AR933X_DDR_TAP_CTRL1 0x20 +#define AR933X_DDR_TAP_CTRL1 0x20 + +#define AR933X_DDR_DDR_DDR2_CONFIG 0x8c +#define AR933X_DDR_DDR_EMR2 0x90 +#define AR933X_DDR_DDR_EMR3 0x94 + +/* * PLL block */ #define AR933X_PLL_CPU_CONFIG_REG 0x00
arch/mips/mach-ath79/include/mach/pbl_macros.h +89 -0
93 lines not on this page · raw message
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 3/10 MIPS: mach-ath79: add pbl_ar9331_uart_enable macro
In reply to Antony Pavlov--- arch/mips/include/asm/pbl_macros.h | 11 +++++++++++ arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 20 ++++++++++++++++++++ arch/mips/mach-ath79/include/mach/pbl_macros.h | 7 +++++++ 3 files changed, 38 insertions(+)
arch/mips/include/asm/pbl_macros.h +11 -0
@@ -37,6 +37,17 @@ .set pop .endm + .macro pbl_reg_set val addr + .set push + .set noreorder + li t9, \addr + li t8, \val + lw t7, 0(t9) + or t7, t8 + sw t7, 0(t9) + .set pop + .endm + .macro pbl_reg_clr clr addr .set push .set noreorder
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +20 -0
@@ -25,6 +25,8 @@#define AR71XX_DDR_CTRL_BASE (AR71XX_APB_BASE + 0x00000000)#define AR71XX_DDR_CTRL_SIZE 0x100 +#define AR71XX_GPIO_BASE (AR71XX_APB_BASE + 0x00040000) +#define AR71XX_GPIO_SIZE 0x100#define AR71XX_PLL_BASE (AR71XX_APB_BASE + 0x00050000)#define AR71XX_PLL_SIZE 0x100#define AR71XX_RESET_BASE (AR71XX_APB_BASE + 0x00060000)
@@ -52,6 +54,24 @@#define AR933X_DDR_DDR_EMR3 0x94/* +* GPIO block +*/ +#define AR71XX_GPIO_REG_OE 0x00 +#define AR71XX_GPIO_REG_IN 0x04 +#define AR71XX_GPIO_REG_OUT 0x08 +#define AR71XX_GPIO_REG_SET 0x0c +#define AR71XX_GPIO_REG_CLEAR 0x10 +#define AR71XX_GPIO_REG_INT_MODE 0x14 +#define AR71XX_GPIO_REG_INT_TYPE 0x18 +#define AR71XX_GPIO_REG_INT_POLARITY 0x1c +#define AR71XX_GPIO_REG_INT_PENDING 0x20 +#define AR71XX_GPIO_REG_INT_ENABLE 0x24 +#define AR71XX_GPIO_REG_FUNC 0x28 +/* Warning! GPIO_FUNC[15] must be written with 1 */ +#define AR933X_GPIO_FUNC_RSRV15 BIT(15) +#define AR933X_GPIO_FUNC_UART_EN BIT(1) + +/* * PLL block */ #define AR933X_PLL_CPU_CONFIG_REG 0x00
arch/mips/mach-ath79/include/mach/pbl_macros.h +7 -0
@@ -129,4 +129,11 @@ .set pop .endm +#define GPIO_FUNC ((KSEG1 | AR71XX_GPIO_BASE) | AR71XX_GPIO_REG_FUNC) + +.macro pbl_ar9331_uart_enable +pbl_reg_set AR933X_GPIO_FUNC_UART_EN \ + | AR933X_GPIO_FUNC_RSRV15, GPIO_FUNC +.endm + #endif /* __ASM_MACH_ATH79_PBL_MACROS_H */
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 4/10 MIPS: mach-ath79: add debug_ll_ar9331_init macro
In reply to Antony Pavlov--- arch/mips/mach-ath79/include/mach/debug_ll.h | 29 ++++++++++++++++++++++++++++ 1 file changed, 29 insertions(+)
arch/mips/mach-ath79/include/mach/debug_ll.h +29 -0
@@ -63,6 +63,35 @@ static inline void PUTC_LL(int ch)* Macros for use in assembly language code */ +#define AR933X_UART_CS_REG 0x04 +#define UART_CS_REG ((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CS_REG) +#define AR933X_UART_CS_IF_MODE_S 2 +#define AR933X_UART_CS_IF_MODE_DCE 2 +#define AR933X_UART_CS_TX_READY_ORIDE BIT(7) +#define AR933X_UART_CS_RX_READY_ORIDE BIT(8) + +/* +* simple uart clock setup +* from u-boot_mod/u-boot/cpu/mips/ar7240/hornet_serial.c +*/ +#define BAUD_CLOCK 25000000 +#define CLOCK_SCALE ((BAUD_CLOCK / (16 * CONFIG_BAUDRATE)) - 1) +#define CLOCK_STEP 0x2000 + +#define AR933X_UART_CLOCK_REG 0x08 +#define CLOCK_REG ((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CLOCK_REG) + +.macro debug_ll_ar9331_init +#ifdef CONFIG_DEBUG_LL + +pbl_reg_writel ((AR933X_UART_CS_IF_MODE_DCE <<AR933X_UART_CS_IF_MODE_S ) \ + |AR933X_UART_CS_TX_READY_ORIDE \ + | AR933X_UART_CS_RX_READY_ORIDE), UART_CS_REG +pbl_reg_writel ((CLOCK_SCALE <<16 ) |CLOCK_STEP ),CLOCK_REG + +#endif /* CONFIG_DEBUG_LL */ +.endm +/* * output a character in a0 */
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 5/10 MIPS: ath79: add black-swift board support
In reply to Antony PavlovBlack Swift is a tiny coin-sized embedded computer based on AR9331 SoC. See http://www.black-swift.com/ for details.
See also Black Swift kickstarter page:
https://www.kickstarter.com/projects/1133560316/black-swift-tiny-wireless-computer
--- arch/mips/Makefile | 1 + arch/mips/boards/black-swift/Makefile | 1 + arch/mips/boards/black-swift/board.c | 27 ++++++++++++++ .../black-swift/include/board/board_pbl_start.h | 41 ++++++++++++++++++++++ arch/mips/dts/black-swift.dts | 34 ++++++++++++++++++ arch/mips/mach-ath79/Kconfig | 6 ++++ 6 files changed, 110 insertions(+)
arch/mips/Makefile +1 -0
@@ -80,6 +80,7 @@ board-$(CONFIG_BOARD_NETGEAR_WG102) := netgear-wg102 machine-$(CONFIG_MACH_MIPS_ATH79) := ath79 board-$(CONFIG_BOARD_TPLINK_MR3020) := tplink-mr3020 +board-$(CONFIG_BOARD_BLACK_SWIFT) := black-swift machine-$(CONFIG_MACH_MIPS_BCM47XX) := bcm47xx board-$(CONFIG_BOARD_DLINK_DIR320) := dlink-dir-320
arch/mips/boards/black-swift/Makefile new file +1 -0
@@ -0,0 +1 @@ +obj-y += board.o
arch/mips/boards/black-swift/board.c new file +27 -0
@@ -0,0 +1,27 @@ +/* +* Copyright (C) 2015 Antony Pavlov <[email protected]> +* +* This file is part of barebox. +* See file CREDITS for list of people who contributed to this project. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License version 2 +* as published by the Free Software Foundation. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +*/ + +#include <common.h> +#include <init.h> + +static int model_hostname_init (void ) +{ +barebox_set_hostname ("black-swift" ); + +return 0 ; +} +postcore_initcall (model_hostname_init);
arch/mips/boards/black-swift/include/board/board_pbl_start.h new file +41 -0
41 lines not on this page · raw message
arch/mips/dts/black-swift.dts new file +34 -0
@@ -0,0 +1,34 @@ +/dts-v1/; + +#include "ar9331.dtsi" + +/ { + model = "Black Swift"; + compatible = "smartlx,black-swift"; + + memory { + reg = <0x00000000 0x4000000>; + }; + + aliases { + spiflash = &spiflash; + }; +}; + +&serial0 { + status = "okay"; +}; + +&spi { + num-chipselects = <1>; + status = "okay"; + + /* Winbond W25Q128FV SPI flash */ + spiflash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p80"; + spi-max-frequency = <104000000>; + reg = <0>; + }; +};
arch/mips/mach-ath79/Kconfig +6 -0
@@ -13,6 +13,12 @@ config BOARD_TPLINK_MR3020 select HAVE_IMAGE_COMPRESSION select HAS_NMON +config BOARD_BLACK_SWIFT + bool "Black Swift" + select HAVE_PBL_IMAGE + select HAVE_IMAGE_COMPRESSION + select HAS_NMON + endchoice endif
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 6/10 MIPS: add black-swift_defconfig
In reply to Antony Pavlov--- arch/mips/configs/black-swift_defconfig | 45 +++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+)
arch/mips/configs/black-swift_defconfig new file +45 -0
@@ -0,0 +1,45 @@ +CONFIG_BUILTIN_DTB=y +CONFIG_BUILTIN_DTB_NAME="black-swift" +CONFIG_MACH_MIPS_ATH79=y +CONFIG_BOARD_BLACK_SWIFT=y +CONFIG_NMON=y +CONFIG_NMON_USER_START=y +CONFIG_NMON_1S_DELAY=0x100000 +CONFIG_NMON_USER_START_DELAY=0x5 +CONFIG_NMON_HELP=y +CONFIG_PBL_IMAGE=y +CONFIG_MALLOC_TLSF=y +CONFIG_CMDLINE_EDITING=y +CONFIG_AUTO_COMPLETE=y +CONFIG_IMD=y +CONFIG_PARTITION=y +CONFIG_DEBUG_LL=y +CONFIG_LONGHELP=y +CONFIG_CMD_IOMEM=y +CONFIG_CMD_MEMINFO=y +# CONFIG_CMD_BOOTM is not set +CONFIG_CMD_GO=y +CONFIG_CMD_LOADB=y +CONFIG_CMD_LOADY=y +CONFIG_CMD_RESET=y +CONFIG_CMD_PARTITION=y +CONFIG_CMD_GLOBAL=y +CONFIG_CMD_SHA1SUM=y +CONFIG_CMD_LET=y +CONFIG_CMD_SLEEP=y +CONFIG_CMD_EDIT=y +CONFIG_CMD_MM=y +CONFIG_CMD_CLK=y +CONFIG_CMD_FLASH=y +CONFIG_CMD_SPI=y +CONFIG_CMD_OF_NODE=y +CONFIG_CMD_OF_PROPERTY=y +CONFIG_CMD_OFTREE=y +CONFIG_OFDEVICE=y +CONFIG_DRIVER_SERIAL_AR933X=y +CONFIG_DRIVER_SPI_ATH79=y +CONFIG_MTD=y +# CONFIG_MTD_OOB_DEVICE is not set +CONFIG_MTD_M25P80=y +CONFIG_DIGEST_SHA224_GENERIC=y +CONFIG_DIGEST_SHA256_GENERIC=y
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 7/10 gpio: add ath79-gpio driver for Atheros MIPS SoCs
In reply to Antony PavlovThis driver is based on linux-4.2 driver.
--- drivers/gpio/Makefile | 1 + drivers/gpio/gpio-ath79.c | 146 ++++++++++++++++++++++++++++++++++++++++++++++ 2 files changed, 147 insertions(+)
drivers/gpio/Makefile +1 -0
@@ -1,6 +1,7 @@ obj-$(CONFIG_GPIOLIB) += gpiolib.o obj-$(CONFIG_GPIO_74164) += gpio-74164.o +obj-$(CONFIG_MACH_MIPS_ATH79) += gpio-ath79.o obj-$(CONFIG_GPIO_BCM2835) += gpio-bcm2835.o obj-$(CONFIG_GPIO_DAVINCI) += gpio-davinci.o obj-$(CONFIG_GPIO_CLPS711X) += gpio-clps711x.o
drivers/gpio/gpio-ath79.c new file +146 -0
146 lines not on this page · raw message
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 8/10 MIPS: ath79: use gpiolib
In reply to Antony Pavlov--- arch/mips/Kconfig | 1 + 1 file changed, 1 insertion(+)
arch/mips/Kconfig +1 -0
@@ -68,6 +68,7 @@ config MACH_MIPS_ATH79 select COMMON_CLK_OF_PROVIDER select CLKDEV_LOOKUP select OFTREE + select GPIOLIB config MACH_MIPS_BCM47XX bool "Broadcom BCM47xx-based boards"
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 9/10 MIPS: dts: ar9331.dtsi: add gpio
In reply to Antony Pavlov--- arch/mips/dts/ar9331.dtsi | 10 ++++++++++ 1 file changed, 10 insertions(+)
arch/mips/dts/ar9331.dtsi +10 -0
@@ -17,6 +17,16 @@ status = "disabled"; }; + gpio: gpio@18040000 { + compatible = "qca,ar7100-gpio"; + gpio-controller; + reg = <0x18040000 0x100>; + #gpio-cells = <2>; + + ngpios = <30>; + status = "disabled"; + }; + ar9331_clk: clock { compatible = "qca,ar933x-clk"; reg = <0x18050000 0x48>;
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
RFC v2 10/10 WIP: MIPS: black-swift: use GPIO
In reply to Antony Pavlov--- arch/mips/boot/start.S | 2 ++ arch/mips/dts/black-swift.dts | 26 ++++++++++++++++++++++++++ 2 files changed, 28 insertions(+)
arch/mips/boot/start.S +2 -0
@@ -34,6 +34,8 @@ EXPORT(_start) mips_disable_interrupts + pbl_reg_set (1 << 18), 0xb80600ac + copy_to_link_location _start stack_setup
arch/mips/dts/black-swift.dts +26 -0
@@ -1,6 +1,8 @@ /dts-v1/; #include "ar9331.dtsi" +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { model = "Black Swift";
@@ -13,6 +15,26 @@ aliases { spiflash = &spiflash; }; + + buttons { + compatible = "gpio-keys"; + + s1 { + label = "S1"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + linux,code = <KEY_UP>; + }; + }; + + leds { + compatible = "gpio-leds"; + + s1 { + label = "LED1"; + gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; }; &serial0 {
@@ -32,3 +54,7 @@ reg = <0>; }; }; + +&gpio { + status = "okay"; +};
Signature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Antony,
Since it's RFC, should I apply this series?
Sascha
Quoted 70 lines · Antony Pavlov
This patchseries adds necessary AR9331 SoC low level initialization routines. The patchseries makes it possible to use barebox as a first stage loader on the Black Swift board and, I suppose, other widespread AR9331-based boards.
The patchseries is heavily based on Oleksij Rempel's work on barebox for TP-Link MR3020.
TODOs:
* add TP-Link MR3020 support (see http://openocd.zylin.com/gitweb?p=openocd.git;a=commitdiff;h=f59d2d9ecfee8899df531b87b7acaa468725f238);
* clean up Black Swift GPIO code (pbl_reg_set(1 << 18),0xb80600ac);
* check macros names linux kernel source compartibility;
* DT compatible string vendor "smartlx" appears un-documented.
The site http://www.smartlx.ru/ is suspended.Changes since RFC v1:
* add UART initialization routune for
DEBUG_LLand NMON;
* add macros forGPIO_FUNCTION_1register initialization;
* add ar71xx GPIO driver.Antony Pavlov (9):
MIPS: ar933x: pbl: addpbl_ar9331_ddr2_configmacro
MIPS: mach-ath79: addpbl_ar9331_uart_enablemacro
MIPS: mach-ath79: adddebug_ll_ar9331_initmacro
MIPS: ath79: add black-swift board support
MIPS: add black-swift_defconfig
gpio: add ath79-gpio driver for Atheros MIPS SoCs
MIPS: ath79: use gpiolib
MIPS: dts:ar9331.dtsi: add gpio
WIP: MIPS: black-swift: use GPIOOleksij Rempel (1):
MIPS: ar933x: pbl: addpbl_ar9331_pllmacroarch/mips/Kconfig | 1 + arch/mips/Makefile | 1 + arch/mips/boards/black-swift/Makefile | 1 + arch/mips/boards/black-swift/board.c | 27 ++++ .../black-swift/include/board/board_pbl_start.h | 41 ++++++ arch/mips/boot/start.S | 2 + arch/mips/configs/black-swift_defconfig | 45 +++++++ arch/mips/dts/ar9331.dtsi | 10 ++ arch/mips/dts/black-swift.dts | 60 +++++++++ arch/mips/include/asm/pbl_macros.h | 32 +++++ arch/mips/mach-ath79/Kconfig | 6 + arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 41 ++++++ arch/mips/mach-ath79/include/mach/debug_ll.h | 29 ++++ arch/mips/mach-ath79/include/mach/pbl_macros.h | 139 ++++++++++++++++++++ drivers/gpio/Makefile | 1 + drivers/gpio/gpio-ath79.c | 146 +++++++++++++++++++++ 16 files changed, 582 insertions(+) create mode 100644 arch/mips/boards/black-swift/Makefile create mode 100644 arch/mips/boards/black-swift/board.c create mode 100644 arch/mips/boards/black-swift/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/black-swift_defconfig create mode 100644 arch/mips/dts/black-swift.dts create mode 100644 arch/mips/mach-ath79/include/mach/pbl_macros.h create mode 100644 drivers/gpio/gpio-ath79.cSignature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 3 lines · On Wed, 23 Sep 2015 06:53:05 +0200 Sascha Hauer <[email protected]> wrote:
Antony,
Since it's RFC, should I apply this series?
No. I have splitted this series to 'ath-79 gpio' and 'ath-79 pbl' series. I have to test 'ath-79 pbl' series more carefully.
Please apply today's 'ath-79 gpio' series (I have posted 'ath-79 gpio' series several hours ago).
Also please change both 'SPL' -> 'SBL' in this commit message from pengutronix/next branch:
commit f24cf07a7702f0f09b133ae5430dbf33610737d7
Author: Antony Pavlov <[email protected]> Date: Mon Sep 21 01:50:45 2015 +0300
MIPS: refactor SPL start.S code
This commit removes code duplication by using
MIPS PBL macros in the SPL start.S file.
Quoted 79 lines
Sascha
Quoted 70 lines · Antony Pavlov
This patchseries adds necessary AR9331 SoC low level initialization routines. The patchseries makes it possible to use barebox as a first stage loader on the Black Swift board and, I suppose, other widespread AR9331-based boards.
The patchseries is heavily based on Oleksij Rempel's work on barebox for TP-Link MR3020.
TODOs:
* add TP-Link MR3020 support (see http://openocd.zylin.com/gitweb?p=openocd.git;a=commitdiff;h=f59d2d9ecfee8899df531b87b7acaa468725f238);
* clean up Black Swift GPIO code (pbl_reg_set(1 << 18),0xb80600ac);
* check macros names linux kernel source compartibility;
* DT compatible string vendor "smartlx" appears un-documented.
The site http://www.smartlx.ru/ is suspended.Changes since RFC v1:
* add UART initialization routune for
DEBUG_LLand NMON;
* add macros forGPIO_FUNCTION_1register initialization;
* add ar71xx GPIO driver.Antony Pavlov (9):
MIPS: ar933x: pbl: addpbl_ar9331_ddr2_configmacro
MIPS: mach-ath79: addpbl_ar9331_uart_enablemacro
MIPS: mach-ath79: adddebug_ll_ar9331_initmacro
MIPS: ath79: add black-swift board support
MIPS: add black-swift_defconfig
gpio: add ath79-gpio driver for Atheros MIPS SoCs
MIPS: ath79: use gpiolib
MIPS: dts:ar9331.dtsi: add gpio
WIP: MIPS: black-swift: use GPIOOleksij Rempel (1):
MIPS: ar933x: pbl: addpbl_ar9331_pllmacroarch/mips/Kconfig | 1 + arch/mips/Makefile | 1 + arch/mips/boards/black-swift/Makefile | 1 + arch/mips/boards/black-swift/board.c | 27 ++++ .../black-swift/include/board/board_pbl_start.h | 41 ++++++ arch/mips/boot/start.S | 2 + arch/mips/configs/black-swift_defconfig | 45 +++++++ arch/mips/dts/ar9331.dtsi | 10 ++ arch/mips/dts/black-swift.dts | 60 +++++++++ arch/mips/include/asm/pbl_macros.h | 32 +++++ arch/mips/mach-ath79/Kconfig | 6 + arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 41 ++++++ arch/mips/mach-ath79/include/mach/debug_ll.h | 29 ++++ arch/mips/mach-ath79/include/mach/pbl_macros.h | 139 ++++++++++++++++++++ drivers/gpio/Makefile | 1 + drivers/gpio/gpio-ath79.c | 146 +++++++++++++++++++++ 16 files changed, 582 insertions(+) create mode 100644 arch/mips/boards/black-swift/Makefile create mode 100644 arch/mips/boards/black-swift/board.c create mode 100644 arch/mips/boards/black-swift/include/board/board_pbl_start.h create mode 100644 arch/mips/configs/black-swift_defconfig create mode 100644 arch/mips/dts/black-swift.dts create mode 100644 arch/mips/mach-ath79/include/mach/pbl_macros.h create mode 100644 drivers/gpio/gpio-ath79.cSignature · 7 lines
2.5.0 _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/bareboxSignature · 4 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
Signature · 8 lines
-- Best regards, Antony Pavlov _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox
Quoted 11 lines · Antony Pavlov
Quoted 3 lines · On Wed, 23 Sep 2015 06:53:05 +0200 Sascha Hauer <[email protected]> wrote:
Antony,
Since it's RFC, should I apply this series?
No. I have splitted this series to 'ath-79 gpio' and 'ath-79 pbl' series. I have to test 'ath-79 pbl' series more carefully.
Please apply today's 'ath-79 gpio' series (I have posted 'ath-79 gpio' series several hours ago).
Ok, applied.
Quoted 2 lines
Also please change both 'SPL' -> 'SBL' in this commit message from pengutronix/next branch:
Did that.
Sascha
Signature · 9 lines
Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list [email protected] http://lists.infradead.org/mailman/listinfo/barebox