Skip to contentSkip to conversation

MIPS: barebox as a first stage loader on the Black Swift board

RFC In review Antony Pavlov 2 participants 14 messages Sep 20, 2015 – Sep 23, 2015

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

v2 cover MIPS: barebox as a first stage loader on the Black Swift board

This patchseries adds necessary AR9331 SoC low level initialization routines. The patchseries makes it possible to use barebox as a first stage loader on the Black Swift board and, I suppose, other widespread AR9331-based boards.

The patchseries is heavily based on Oleksij Rempel's work on barebox for TP-Link MR3020.

TODOs:

* add TP-Link MR3020 support (see http://openocd.zylin.com/gitweb?p=openocd.git;a=commitdiff;h=f59d2d9ecfee8899df531b87b7acaa468725f238);
* clean up Black Swift GPIO code (pbl_reg_set (1 << 18), 0xb80600ac);
* check macros names linux kernel source compartibility;
* DT compatible string vendor "smartlx" appears un-documented.
The site http://www.smartlx.ru/ is suspended.

Changes since RFC v1:

* add UART initialization routune for DEBUG_LL and NMON;
* add macros for GPIO_FUNCTION_1 register initialization;
* add ar71xx GPIO driver.

Antony Pavlov (9):
MIPS: ar933x: pbl: add pbl_ar9331_ddr2_config macro
MIPS: mach-ath79: add pbl_ar9331_uart_enable macro
MIPS: mach-ath79: add debug_ll_ar9331_init macro
MIPS: ath79: add black-swift board support
MIPS: add black-swift_defconfig
gpio: add ath79-gpio driver for Atheros MIPS SoCs
MIPS: ath79: use gpiolib
MIPS: dts: ar9331.dtsi: add gpio
WIP: MIPS: black-swift: use GPIO

Oleksij Rempel (1):
MIPS: ar933x: pbl: add pbl_ar9331_pll macro

 arch/mips/Kconfig                                  |   1 +
 arch/mips/Makefile                                 |   1 +
 arch/mips/boards/black-swift/Makefile              |   1 +
 arch/mips/boards/black-swift/board.c               |  27 ++++
 .../black-swift/include/board/board_pbl_start.h    |  41 ++++++
 arch/mips/boot/start.S                             |   2 +
 arch/mips/configs/black-swift_defconfig            |  45 +++++++
 arch/mips/dts/ar9331.dtsi                          |  10 ++
 arch/mips/dts/black-swift.dts                      |  60 +++++++++
 arch/mips/include/asm/pbl_macros.h                 |  32 +++++
 arch/mips/mach-ath79/Kconfig                       |   6 +
 arch/mips/mach-ath79/include/mach/ar71xx_regs.h    |  41 ++++++
 arch/mips/mach-ath79/include/mach/debug_ll.h       |  29 ++++
 arch/mips/mach-ath79/include/mach/pbl_macros.h     | 139 ++++++++++++++++++++
 drivers/gpio/Makefile                              |   1 +
 drivers/gpio/gpio-ath79.c                          | 146 +++++++++++++++++++++
 16 files changed, 582 insertions(+)
 create mode 100644 arch/mips/boards/black-swift/Makefile
 create mode 100644 arch/mips/boards/black-swift/board.c
 create mode 100644 arch/mips/boards/black-swift/include/board/board_pbl_start.h
 create mode 100644 arch/mips/configs/black-swift_defconfig
 create mode 100644 arch/mips/dts/black-swift.dts
 create mode 100644 arch/mips/mach-ath79/include/mach/pbl_macros.h
 create mode 100644 drivers/gpio/gpio-ath79.c
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#1 lore raw

RFC v2 1/10 MIPS: ar933x: pbl: add pbl_ar9331_pll macro

From: Oleksij Rempel <[email protected]>

---
 arch/mips/include/asm/pbl_macros.h              | 21 ++++++++++++
 arch/mips/mach-ath79/include/mach/ar71xx_regs.h |  1 +
 arch/mips/mach-ath79/include/mach/pbl_macros.h  | 43 +++++++++++++++++++++++++
 3 files changed, 65 insertions(+)
arch/mips/include/asm/pbl_macros.h +21 -0
index 1d9d6ab..db46d0d 100644
@@ -28,6 +28,27 @@
 #include <generated/compile.h>
 #include <generated/utsrelease.h>
 
+	.macro	pbl_reg_writel val addr
+	.set push
+	.set noreorder
+	li	t9, \addr
+	li	t8, \val
+	sw	t8, 0(t9)
+	.set	pop
+	.endm
+
+	.macro	pbl_reg_clr clr addr
+	.set push
+	.set noreorder
+	li	t9, \addr
+	li	t8, \clr
+	lw	t7, 0(t9)
+	not	t8, t8
+	and	t7, t8
+	sw	t7, 0(t9)
+	.set	pop
+	.endm
+
 	.macro	pbl_sleep reg count
 	.set push
 	.set noreorder
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +1 -0
index 77138ab..5082502 100644
@@ -46,6 +46,7 @@
 #define AR933X_PLL_CPU_CONFIG_REFDIV_MASK	0x1f
 #define AR933X_PLL_CPU_CONFIG_OUTDIV_SHIFT	23
 #define AR933X_PLL_CPU_CONFIG_OUTDIV_MASK	0x7
+#define AR933X_PLL_CPU_CONFIG_PLLPWD		BIT(30)
 
 #define AR933X_PLL_CLOCK_CTRL_BYPASS		BIT(2)
 #define AR933X_PLL_CLOCK_CTRL_CPU_DIV_SHIFT	5
arch/mips/mach-ath79/include/mach/pbl_macros.h new file +43 -0

43 lines not on this page · raw message

Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#2 lore raw

RFC v2 2/10 MIPS: ar933x: pbl: add pbl_ar9331_ddr2_config macro

In reply to Antony Pavlov
---
 arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 20 ++++++
 arch/mips/mach-ath79/include/mach/pbl_macros.h  | 89 +++++++++++++++++++++++++
 2 files changed, 109 insertions(+)
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +20 -0
index 5082502..6f1bf8e 100644
@@ -23,6 +23,8 @@
 
 #define AR71XX_APB_BASE		0x18000000
 
+#define AR71XX_DDR_CTRL_BASE	(AR71XX_APB_BASE + 0x00000000)
+#define AR71XX_DDR_CTRL_SIZE	0x100
 #define AR71XX_PLL_BASE		(AR71XX_APB_BASE + 0x00050000)
 #define AR71XX_PLL_SIZE		0x100
 #define AR71XX_RESET_BASE	(AR71XX_APB_BASE + 0x00060000)
@@ -32,6 +34,24 @@
 #define AR933X_UART_SIZE	0x14
 
 /*
+ * DDR_CTRL block
+ */
+#define AR933X_DDR_CONFIG		0x00
+#define AR933X_DDR_CONFIG2		0x04
+#define AR933X_DDR_MODE			0x08
+#define AR933X_DDR_EXT_MODE		0x0c
+#define AR933X_DDR_CTRL			0x10
+#define AR933X_DDR_REFRESH		0x14
+#define AR933X_DDR_RD_DATA		0x18
+#define AR933X_DDR_TAP_CTRL0		0x1c
+#define AR933X_DDR_TAP_CTRL1		0x20
+#define AR933X_DDR_TAP_CTRL1		0x20
+
+#define AR933X_DDR_DDR_DDR2_CONFIG	0x8c
+#define AR933X_DDR_DDR_EMR2		0x90
+#define AR933X_DDR_DDR_EMR3		0x94
+
+/*
  * PLL block
  */
 #define AR933X_PLL_CPU_CONFIG_REG	0x00
arch/mips/mach-ath79/include/mach/pbl_macros.h +89 -0

93 lines not on this page · raw message

Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#3 lore raw

RFC v2 3/10 MIPS: mach-ath79: add pbl_ar9331_uart_enable macro

In reply to Antony Pavlov
---
 arch/mips/include/asm/pbl_macros.h              | 11 +++++++++++
 arch/mips/mach-ath79/include/mach/ar71xx_regs.h | 20 ++++++++++++++++++++
 arch/mips/mach-ath79/include/mach/pbl_macros.h  |  7 +++++++
 3 files changed, 38 insertions(+)
arch/mips/include/asm/pbl_macros.h +11 -0
index db46d0d..681b40a 100644
@@ -37,6 +37,17 @@
 	.set	pop
 	.endm
 
+	.macro	pbl_reg_set val addr
+	.set push
+	.set noreorder
+	li	t9, \addr
+	li	t8, \val
+	lw	t7, 0(t9)
+	or	t7, t8
+	sw	t7, 0(t9)
+	.set	pop
+	.endm
+
 	.macro	pbl_reg_clr clr addr
 	.set push
 	.set noreorder
arch/mips/mach-ath79/include/mach/ar71xx_regs.h +20 -0
index 6f1bf8e..4cbe94a 100644
@@ -25,6 +25,8 @@
 
 #define AR71XX_DDR_CTRL_BASE	(AR71XX_APB_BASE + 0x00000000)
 #define AR71XX_DDR_CTRL_SIZE	0x100
+#define AR71XX_GPIO_BASE	(AR71XX_APB_BASE + 0x00040000)
+#define AR71XX_GPIO_SIZE	0x100
 #define AR71XX_PLL_BASE		(AR71XX_APB_BASE + 0x00050000)
 #define AR71XX_PLL_SIZE		0x100
 #define AR71XX_RESET_BASE	(AR71XX_APB_BASE + 0x00060000)
@@ -52,6 +54,24 @@
 #define AR933X_DDR_DDR_EMR3		0x94
 
 /*
+ * GPIO block
+ */
+#define AR71XX_GPIO_REG_OE		0x00
+#define AR71XX_GPIO_REG_IN		0x04
+#define AR71XX_GPIO_REG_OUT		0x08
+#define AR71XX_GPIO_REG_SET		0x0c
+#define AR71XX_GPIO_REG_CLEAR		0x10
+#define AR71XX_GPIO_REG_INT_MODE	0x14
+#define AR71XX_GPIO_REG_INT_TYPE	0x18
+#define AR71XX_GPIO_REG_INT_POLARITY	0x1c
+#define AR71XX_GPIO_REG_INT_PENDING	0x20
+#define AR71XX_GPIO_REG_INT_ENABLE	0x24
+#define AR71XX_GPIO_REG_FUNC		0x28
+/* Warning! GPIO_FUNC[15] must be written with 1 */
+#define AR933X_GPIO_FUNC_RSRV15			BIT(15)
+#define AR933X_GPIO_FUNC_UART_EN		BIT(1)
+
+/*
  * PLL block
  */
 #define AR933X_PLL_CPU_CONFIG_REG	0x00
arch/mips/mach-ath79/include/mach/pbl_macros.h +7 -0
index f0e0174..4ef90dc 100644
@@ -129,4 +129,11 @@
 	.set	pop
 .endm
 
+#define GPIO_FUNC	((KSEG1 | AR71XX_GPIO_BASE) | AR71XX_GPIO_REG_FUNC)
+
+.macro	pbl_ar9331_uart_enable
+	pbl_reg_set AR933X_GPIO_FUNC_UART_EN \
+			| AR933X_GPIO_FUNC_RSRV15, GPIO_FUNC
+.endm
+
 #endif /* __ASM_MACH_ATH79_PBL_MACROS_H */
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#4 lore raw

RFC v2 4/10 MIPS: mach-ath79: add debug_ll_ar9331_init macro

In reply to Antony Pavlov
---
 arch/mips/mach-ath79/include/mach/debug_ll.h | 29 ++++++++++++++++++++++++++++
 1 file changed, 29 insertions(+)
arch/mips/mach-ath79/include/mach/debug_ll.h +29 -0
index d3813af..e0c3f79 100644
@@ -63,6 +63,35 @@ static inline void PUTC_LL(int ch)
  * Macros for use in assembly language code
  */
 
+#define AR933X_UART_CS_REG		0x04
+#define UART_CS_REG	((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CS_REG)
+#define AR933X_UART_CS_IF_MODE_S	2
+#define	  AR933X_UART_CS_IF_MODE_DCE	2
+#define AR933X_UART_CS_TX_READY_ORIDE	BIT(7)
+#define AR933X_UART_CS_RX_READY_ORIDE	BIT(8)
+
+/*
+ * simple uart clock setup
+ * from u-boot_mod/u-boot/cpu/mips/ar7240/hornet_serial.c
+ */
+#define BAUD_CLOCK 25000000
+#define CLOCK_SCALE ((BAUD_CLOCK / (16 * CONFIG_BAUDRATE)) - 1)
+#define CLOCK_STEP 0x2000
+
+#define AR933X_UART_CLOCK_REG		0x08
+#define CLOCK_REG	((KSEG1 | AR933X_UART_BASE) | AR933X_UART_CLOCK_REG)
+
+.macro debug_ll_ar9331_init
+#ifdef CONFIG_DEBUG_LL
+
+	pbl_reg_writel ((AR933X_UART_CS_IF_MODE_DCE << AR933X_UART_CS_IF_MODE_S) \
+			| AR933X_UART_CS_TX_READY_ORIDE \
+			| AR933X_UART_CS_RX_READY_ORIDE), UART_CS_REG
+	pbl_reg_writel ((CLOCK_SCALE << 16) | CLOCK_STEP), CLOCK_REG
+
+#endif /* CONFIG_DEBUG_LL */
+.endm
+
 /*
  * output a character in a0
  */
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#5 lore raw

RFC v2 5/10 MIPS: ath79: add black-swift board support

In reply to Antony Pavlov

Black Swift is a tiny coin-sized embedded computer based on AR9331 SoC. See http://www.black-swift.com/ for details.

See also Black Swift kickstarter page:
https://www.kickstarter.com/projects/1133560316/black-swift-tiny-wireless-computer

---
 arch/mips/Makefile                                 |  1 +
 arch/mips/boards/black-swift/Makefile              |  1 +
 arch/mips/boards/black-swift/board.c               | 27 ++++++++++++++
 .../black-swift/include/board/board_pbl_start.h    | 41 ++++++++++++++++++++++
 arch/mips/dts/black-swift.dts                      | 34 ++++++++++++++++++
 arch/mips/mach-ath79/Kconfig                       |  6 ++++
 6 files changed, 110 insertions(+)
arch/mips/Makefile +1 -0
index 6ef2bf7..75761b5 100644
@@ -80,6 +80,7 @@ board-$(CONFIG_BOARD_NETGEAR_WG102)	:= netgear-wg102
 
 machine-$(CONFIG_MACH_MIPS_ATH79)	:= ath79
 board-$(CONFIG_BOARD_TPLINK_MR3020)	:= tplink-mr3020
+board-$(CONFIG_BOARD_BLACK_SWIFT)	:= black-swift
 
 machine-$(CONFIG_MACH_MIPS_BCM47XX)	:= bcm47xx
 board-$(CONFIG_BOARD_DLINK_DIR320)	:= dlink-dir-320
arch/mips/boards/black-swift/Makefile new file +1 -0
new file mode 100644
index 0000000..dcfc293
@@ -0,0 +1 @@
+obj-y += board.o
arch/mips/boards/black-swift/board.c new file +27 -0
new file mode 100644
index 0000000..2e2ed20
@@ -0,0 +1,27 @@
+/*
+ * Copyright (C) 2015 Antony Pavlov <[email protected]>
+ *
+ * This file is part of barebox.
+ * See file CREDITS for list of people who contributed to this project.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <common.h>
+#include <init.h>
+
+static int model_hostname_init(void)
+{
+	barebox_set_hostname("black-swift");
+
+	return 0;
+}
+postcore_initcall(model_hostname_init);
arch/mips/boards/black-swift/include/board/board_pbl_start.h new file +41 -0

41 lines not on this page · raw message

arch/mips/dts/black-swift.dts new file +34 -0
new file mode 100644
index 0000000..270374d
@@ -0,0 +1,34 @@
+/dts-v1/;
+
+#include "ar9331.dtsi"
+
+/ {
+	model = "Black Swift";
+	compatible = "smartlx,black-swift";
+
+	memory {
+		reg = <0x00000000 0x4000000>;
+	};
+
+	aliases {
+		spiflash = &spiflash;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&spi {
+	num-chipselects = <1>;
+	status = "okay";
+
+	/* Winbond W25Q128FV SPI flash */
+	spiflash: m25p80@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "m25p80";
+		spi-max-frequency = <104000000>;
+		reg = <0>;
+	};
+};
arch/mips/mach-ath79/Kconfig +6 -0
index f730b37..9b8e394 100644
@@ -13,6 +13,12 @@ config BOARD_TPLINK_MR3020
 	select HAVE_IMAGE_COMPRESSION
 	select HAS_NMON
 
+config BOARD_BLACK_SWIFT
+	bool "Black Swift"
+	select HAVE_PBL_IMAGE
+	select HAVE_IMAGE_COMPRESSION
+	select HAS_NMON
+
 endchoice
 
 endif
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#6 lore raw

RFC v2 6/10 MIPS: add black-swift_defconfig

In reply to Antony Pavlov
---
 arch/mips/configs/black-swift_defconfig | 45 +++++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)
arch/mips/configs/black-swift_defconfig new file +45 -0
new file mode 100644
index 0000000..cfe2a8f
@@ -0,0 +1,45 @@
+CONFIG_BUILTIN_DTB=y
+CONFIG_BUILTIN_DTB_NAME="black-swift"
+CONFIG_MACH_MIPS_ATH79=y
+CONFIG_BOARD_BLACK_SWIFT=y
+CONFIG_NMON=y
+CONFIG_NMON_USER_START=y
+CONFIG_NMON_1S_DELAY=0x100000
+CONFIG_NMON_USER_START_DELAY=0x5
+CONFIG_NMON_HELP=y
+CONFIG_PBL_IMAGE=y
+CONFIG_MALLOC_TLSF=y
+CONFIG_CMDLINE_EDITING=y
+CONFIG_AUTO_COMPLETE=y
+CONFIG_IMD=y
+CONFIG_PARTITION=y
+CONFIG_DEBUG_LL=y
+CONFIG_LONGHELP=y
+CONFIG_CMD_IOMEM=y
+CONFIG_CMD_MEMINFO=y
+# CONFIG_CMD_BOOTM is not set
+CONFIG_CMD_GO=y
+CONFIG_CMD_LOADB=y
+CONFIG_CMD_LOADY=y
+CONFIG_CMD_RESET=y
+CONFIG_CMD_PARTITION=y
+CONFIG_CMD_GLOBAL=y
+CONFIG_CMD_SHA1SUM=y
+CONFIG_CMD_LET=y
+CONFIG_CMD_SLEEP=y
+CONFIG_CMD_EDIT=y
+CONFIG_CMD_MM=y
+CONFIG_CMD_CLK=y
+CONFIG_CMD_FLASH=y
+CONFIG_CMD_SPI=y
+CONFIG_CMD_OF_NODE=y
+CONFIG_CMD_OF_PROPERTY=y
+CONFIG_CMD_OFTREE=y
+CONFIG_OFDEVICE=y
+CONFIG_DRIVER_SERIAL_AR933X=y
+CONFIG_DRIVER_SPI_ATH79=y
+CONFIG_MTD=y
+# CONFIG_MTD_OOB_DEVICE is not set
+CONFIG_MTD_M25P80=y
+CONFIG_DIGEST_SHA224_GENERIC=y
+CONFIG_DIGEST_SHA256_GENERIC=y
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#7 lore raw

RFC v2 7/10 gpio: add ath79-gpio driver for Atheros MIPS SoCs

In reply to Antony Pavlov

This driver is based on linux-4.2 driver.

---
 drivers/gpio/Makefile     |   1 +
 drivers/gpio/gpio-ath79.c | 146 ++++++++++++++++++++++++++++++++++++++++++++++
 2 files changed, 147 insertions(+)
drivers/gpio/Makefile +1 -0
index 1d94661..f39e8da 100644
@@ -1,6 +1,7 @@
 obj-$(CONFIG_GPIOLIB)		+= gpiolib.o
 
 obj-$(CONFIG_GPIO_74164)	+= gpio-74164.o
+obj-$(CONFIG_MACH_MIPS_ATH79)	+= gpio-ath79.o
 obj-$(CONFIG_GPIO_BCM2835)	+= gpio-bcm2835.o
 obj-$(CONFIG_GPIO_DAVINCI)	+= gpio-davinci.o
 obj-$(CONFIG_GPIO_CLPS711X)	+= gpio-clps711x.o
drivers/gpio/gpio-ath79.c new file +146 -0

146 lines not on this page · raw message

Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#8 lore raw

RFC v2 8/10 MIPS: ath79: use gpiolib

In reply to Antony Pavlov
---
 arch/mips/Kconfig | 1 +
 1 file changed, 1 insertion(+)
arch/mips/Kconfig +1 -0
index aeb5c04..a2d443f 100644
@@ -68,6 +68,7 @@ config MACH_MIPS_ATH79
 	select COMMON_CLK_OF_PROVIDER
 	select CLKDEV_LOOKUP
 	select OFTREE
+	select GPIOLIB
 
 config MACH_MIPS_BCM47XX
 	bool "Broadcom BCM47xx-based boards"
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#9 lore raw

RFC v2 9/10 MIPS: dts: ar9331.dtsi: add gpio

In reply to Antony Pavlov
---
 arch/mips/dts/ar9331.dtsi | 10 ++++++++++
 1 file changed, 10 insertions(+)
arch/mips/dts/ar9331.dtsi +10 -0
index 8e7afcd..99ede9e 100644
@@ -17,6 +17,16 @@
 			status = "disabled";
 		};
 
+		gpio: gpio@18040000 {
+			compatible = "qca,ar7100-gpio";
+			gpio-controller;
+			reg = <0x18040000 0x100>;
+			#gpio-cells = <2>;
+
+			ngpios = <30>;
+			status = "disabled";
+		};
+
 		ar9331_clk: clock {
 			compatible = "qca,ar933x-clk";
 			reg = <0x18050000 0x48>;
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#10 lore raw

RFC v2 10/10 WIP: MIPS: black-swift: use GPIO

In reply to Antony Pavlov
---
 arch/mips/boot/start.S        |  2 ++
 arch/mips/dts/black-swift.dts | 26 ++++++++++++++++++++++++++
 2 files changed, 28 insertions(+)
arch/mips/boot/start.S +2 -0
index 1ddce95..d6449e1 100644
@@ -34,6 +34,8 @@ EXPORT(_start)
 
 	mips_disable_interrupts
 
+	pbl_reg_set (1 << 18), 0xb80600ac
+
 	copy_to_link_location _start
 
 	stack_setup
arch/mips/dts/black-swift.dts +26 -0
index 270374d..e2d1271 100644
@@ -1,6 +1,8 @@
 /dts-v1/;
 
 #include "ar9331.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 
 / {
 	model = "Black Swift";
@@ -13,6 +15,26 @@
 	aliases {
 		spiflash = &spiflash;
 	};
+
+	buttons {
+		compatible = "gpio-keys";
+
+		s1 {
+			label = "S1";
+			gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_UP>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		s1 {
+			label = "LED1";
+			gpios = <&gpio 27 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
 };
 
 &serial0 {
@@ -32,3 +54,7 @@
 		reg = <0>;
 	};
 };
+
+&gpio {
+	status = "okay";
+};
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#11 lore raw
In reply to Antony Pavlov

Antony,

Since it's RFC, should I apply this series?

Sascha

Quoted 70 lines · Antony Pavlov

This patchseries adds necessary AR9331 SoC low level initialization routines. The patchseries makes it possible to use barebox as a first stage loader on the Black Swift board and, I suppose, other widespread AR9331-based boards.

The patchseries is heavily based on Oleksij Rempel's work on barebox for TP-Link MR3020.

TODOs:

* add TP-Link MR3020 support (see http://openocd.zylin.com/gitweb?p=openocd.git;a=commitdiff;h=f59d2d9ecfee8899df531b87b7acaa468725f238);
* clean up Black Swift GPIO code (pbl_reg_set (1 << 18), 0xb80600ac);
* check macros names linux kernel source compartibility;
* DT compatible string vendor "smartlx" appears un-documented.
The site http://www.smartlx.ru/ is suspended.

Changes since RFC v1:

* add UART initialization routune for DEBUG_LL and NMON;
* add macros for GPIO_FUNCTION_1 register initialization;
* add ar71xx GPIO driver.

Antony Pavlov (9):
MIPS: ar933x: pbl: add pbl_ar9331_ddr2_config macro
MIPS: mach-ath79: add pbl_ar9331_uart_enable macro
MIPS: mach-ath79: add debug_ll_ar9331_init macro
MIPS: ath79: add black-swift board support
MIPS: add black-swift_defconfig
gpio: add ath79-gpio driver for Atheros MIPS SoCs
MIPS: ath79: use gpiolib
MIPS: dts: ar9331.dtsi: add gpio
WIP: MIPS: black-swift: use GPIO

Oleksij Rempel (1):
MIPS: ar933x: pbl: add pbl_ar9331_pll macro

 arch/mips/Kconfig                                  |   1 +
 arch/mips/Makefile                                 |   1 +
 arch/mips/boards/black-swift/Makefile              |   1 +
 arch/mips/boards/black-swift/board.c               |  27 ++++
 .../black-swift/include/board/board_pbl_start.h    |  41 ++++++
 arch/mips/boot/start.S                             |   2 +
 arch/mips/configs/black-swift_defconfig            |  45 +++++++
 arch/mips/dts/ar9331.dtsi                          |  10 ++
 arch/mips/dts/black-swift.dts                      |  60 +++++++++
 arch/mips/include/asm/pbl_macros.h                 |  32 +++++
 arch/mips/mach-ath79/Kconfig                       |   6 +
 arch/mips/mach-ath79/include/mach/ar71xx_regs.h    |  41 ++++++
 arch/mips/mach-ath79/include/mach/debug_ll.h       |  29 ++++
 arch/mips/mach-ath79/include/mach/pbl_macros.h     | 139 ++++++++++++++++++++
 drivers/gpio/Makefile                              |   1 +
 drivers/gpio/gpio-ath79.c                          | 146 +++++++++++++++++++++
 16 files changed, 582 insertions(+)
 create mode 100644 arch/mips/boards/black-swift/Makefile
 create mode 100644 arch/mips/boards/black-swift/board.c
 create mode 100644 arch/mips/boards/black-swift/include/board/board_pbl_start.h
 create mode 100644 arch/mips/configs/black-swift_defconfig
 create mode 100644 arch/mips/dts/black-swift.dts
 create mode 100644 arch/mips/mach-ath79/include/mach/pbl_macros.h
 create mode 100644 drivers/gpio/gpio-ath79.c
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Signature · 9 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#12 lore raw
Quoted 3 lines · On Wed, 23 Sep 2015 06:53:05 +0200 Sascha Hauer <[email protected]> wrote:

Antony,

Since it's RFC, should I apply this series?

No. I have splitted this series to 'ath-79 gpio' and 'ath-79 pbl' series. I have to test 'ath-79 pbl' series more carefully.
Please apply today's 'ath-79 gpio' series (I have posted 'ath-79 gpio' series several hours ago).

Also please change both 'SPL' -> 'SBL' in this commit message from pengutronix/next branch:

commit f24cf07a7702f0f09b133ae5430dbf33610737d7

Author: Antony Pavlov <[email protected]>
Date:   Mon Sep 21 01:50:45 2015 +0300

MIPS: refactor SPL start.S code

This commit removes code duplication by using
MIPS PBL macros in the SPL start.S file.

Quoted 79 lines

Sascha

Quoted 70 lines · Antony Pavlov

This patchseries adds necessary AR9331 SoC low level initialization routines. The patchseries makes it possible to use barebox as a first stage loader on the Black Swift board and, I suppose, other widespread AR9331-based boards.

The patchseries is heavily based on Oleksij Rempel's work on barebox for TP-Link MR3020.

TODOs:

* add TP-Link MR3020 support (see http://openocd.zylin.com/gitweb?p=openocd.git;a=commitdiff;h=f59d2d9ecfee8899df531b87b7acaa468725f238);
* clean up Black Swift GPIO code (pbl_reg_set (1 << 18), 0xb80600ac);
* check macros names linux kernel source compartibility;
* DT compatible string vendor "smartlx" appears un-documented.
The site http://www.smartlx.ru/ is suspended.

Changes since RFC v1:

* add UART initialization routune for DEBUG_LL and NMON;
* add macros for GPIO_FUNCTION_1 register initialization;
* add ar71xx GPIO driver.

Antony Pavlov (9):
MIPS: ar933x: pbl: add pbl_ar9331_ddr2_config macro
MIPS: mach-ath79: add pbl_ar9331_uart_enable macro
MIPS: mach-ath79: add debug_ll_ar9331_init macro
MIPS: ath79: add black-swift board support
MIPS: add black-swift_defconfig
gpio: add ath79-gpio driver for Atheros MIPS SoCs
MIPS: ath79: use gpiolib
MIPS: dts: ar9331.dtsi: add gpio
WIP: MIPS: black-swift: use GPIO

Oleksij Rempel (1):
MIPS: ar933x: pbl: add pbl_ar9331_pll macro

 arch/mips/Kconfig                                  |   1 +
 arch/mips/Makefile                                 |   1 +
 arch/mips/boards/black-swift/Makefile              |   1 +
 arch/mips/boards/black-swift/board.c               |  27 ++++
 .../black-swift/include/board/board_pbl_start.h    |  41 ++++++
 arch/mips/boot/start.S                             |   2 +
 arch/mips/configs/black-swift_defconfig            |  45 +++++++
 arch/mips/dts/ar9331.dtsi                          |  10 ++
 arch/mips/dts/black-swift.dts                      |  60 +++++++++
 arch/mips/include/asm/pbl_macros.h                 |  32 +++++
 arch/mips/mach-ath79/Kconfig                       |   6 +
 arch/mips/mach-ath79/include/mach/ar71xx_regs.h    |  41 ++++++
 arch/mips/mach-ath79/include/mach/debug_ll.h       |  29 ++++
 arch/mips/mach-ath79/include/mach/pbl_macros.h     | 139 ++++++++++++++++++++
 drivers/gpio/Makefile                              |   1 +
 drivers/gpio/gpio-ath79.c                          | 146 +++++++++++++++++++++
 16 files changed, 582 insertions(+)
 create mode 100644 arch/mips/boards/black-swift/Makefile
 create mode 100644 arch/mips/boards/black-swift/board.c
 create mode 100644 arch/mips/boards/black-swift/include/board/board_pbl_start.h
 create mode 100644 arch/mips/configs/black-swift_defconfig
 create mode 100644 arch/mips/dts/black-swift.dts
 create mode 100644 arch/mips/mach-ath79/include/mach/pbl_macros.h
 create mode 100644 drivers/gpio/gpio-ath79.c
Signature · 7 lines
2.5.0


_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
Signature · 4 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |
Signature · 8 lines
-- 
Best regards,
  Antony Pavlov

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox
#13 lore raw
Quoted 11 lines · Antony Pavlov
Quoted 3 lines · On Wed, 23 Sep 2015 06:53:05 +0200 Sascha Hauer <[email protected]> wrote:

Antony,

Since it's RFC, should I apply this series?

No. I have splitted this series to 'ath-79 gpio' and 'ath-79 pbl' series. I have to test 'ath-79 pbl' series more carefully.
Please apply today's 'ath-79 gpio' series (I have posted 'ath-79 gpio' series several hours ago).

Ok, applied.

Quoted 2 lines

Also please change both 'SPL' -> 'SBL' in this commit message from pengutronix/next branch:

Did that.

Sascha

Signature · 9 lines
Pengutronix e.K.                           |                             |
Industrial Linux Solutions                 | http://www.pengutronix.de/  |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
barebox mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/barebox