raspberrypi3: fix serial console (add enable_uart=1)
PATCH 1/1 raspberrypi3: fix serial console (add enable_uart=1)
- enhance post-image.sh script to add 'enable_uart=1' to config.txt on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart" in raspberrypi3_defconfig
--- board/raspberrypi/post-image.sh | 13 +++++++++++++ board/raspberrypi/readme.txt | 6 +++++- configs/raspberrypi3_defconfig | 1 + 3 files changed, 19 insertions(+), 1 deletion(-)
board/raspberrypi/post-image.sh +13 -0
@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})" GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg" GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp" +case "${2}" in + --add-rpi3-config-enable-uart) + if ! grep -qE 'enable_uart=1' "${BINARIES_DIR}/rpi-firmware/config.txt"; then + echo "Adding 'enable_uart=1' to config.txt." + cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt" + +# fixes rpi3 console +enable_uart=1 +__EOF__ + fi + ;; +esac + # Mark the kernel as DT-enabled mkdir -p "${BINARIES_DIR}/kernel-marked" ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \
board/raspberrypi/readme.txt +5 -1
@@ -58,7 +58,7 @@ After building, you should obtain this tree: +-- rpi-firmware/ | +-- bootcode.bin | +-- cmdline.txt - | +-- config.txt + | +-- config.txt [3] | +-- fixup.dat | `-- start.elf +-- sdcard.img
@@ -69,6 +69,10 @@ After building, you should obtain this tree: [2] This is the mkknlimg DT-marked kernel. +[3] For Pi 3 an additional 'enable_uart=1' will be added to fix + (serial) console output. Alternatives are 'dtoverlay=pi3-miniuart-bt' + or 'dtoverlay=pi3-disable-bt'. + How to write the SD card ========================
configs/raspberrypi3_defconfig +1 -0
@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y # BR2_TARGET_ROOTFS_TAR is not set BR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh" BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart"
Signature · 1 line
2.8.1
PATCH 1/1 raspberrypi3: fix serial console (add enable_uart=1)
Quoted 67 lines · Peter Seiderer
- enhance
post-image.shscript to add 'enable_uart=1' to config.txt on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart" inraspberrypi3_defconfigSigned-off-by Peter Seiderer <[email protected]>---
board/raspberrypi/post-image.sh | 13 +++++++++++++ board/raspberrypi/readme.txt | 6 +++++- configs/raspberrypi3_defconfig | 1 + 3 files changed, 19 insertions(+), 1 deletion(-)board/raspberrypi/post-image.sh +0
-0@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})"GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg" GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
board/raspberrypi/post-image.sh +13
-0+case "${2}" in + --add-rpi3-config-enable-uart) + if ! grep -qE 'enable_uart=1' "${BINARIES_DIR}/rpi-firmware/config.txt"; then + echo "Adding 'enable_uart=1' to config.txt." + cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt" + +# fixes rpi3 console +enable_uart=1 +__EOF__ + fi + ;; +esac +# Mark the kernel as DT-enabled
mkdir -p "${BINARIES_DIR}/kernel-marked" ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \board/raspberrypi/readme.txt +1
-1@@ -58,7 +58,7 @@ After building, you should obtain this tree: +-- rpi-firmware/ | +-- bootcode.bin | +-- cmdline.txt - | +-- config.txt + | +-- config.txt [3] | +-- fixup.dat | `-- start.elf +-- sdcard.img@@ -69,6 +69,10 @@ After building, you should obtain this tree:[2] This is the mkknlimg DT-marked kernel.
+[3] For Pi 3 an additional 'enable_uart=1' will be added to fix
board/raspberrypi/readme.txt +3
-0+ (serial) console output. Alternatives are 'dtoverlay=pi3-miniuart-bt' + or 'dtoverlay=pi3-disable-bt'. +How to write the SD card
========================configs/raspberrypi3_defconfig +0
-0@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y # BR2_TARGET_ROOTFS_TAR is not set
Quoted 3 lines
BR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh" BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart?
This lowers the core clock speed to minimum, so if you are doing some high definition video decode or interlace then you might want this disabled. I would recommend keeping it disabled by default.
Quoted 7 lines
--
2.8.1_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 204 bytes
Desc: Message signed with OpenPGP using GPGMail
URL: <http://lists.busybox.net/pipermail/buildroot/attachments/20160811/11a33ed7/attachment.asc>
PATCH 1/1 raspberrypi3: fix serial console (add enable_uart=1)
Hello Khem Raj,
Quoted 61 lines · Khem Raj
Quoted 61 lines · Peter Seiderer
- enhance
post-image.shscript to add 'enable_uart=1' to config.txt on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart" inraspberrypi3_defconfigSigned-off-by Peter Seiderer <[email protected]>---
board/raspberrypi/post-image.sh | 13 +++++++++++++ board/raspberrypi/readme.txt | 6 +++++- configs/raspberrypi3_defconfig | 1 + 3 files changed, 19 insertions(+), 1 deletion(-)board/raspberrypi/post-image.sh +0
-0@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})"GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg" GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
board/raspberrypi/post-image.sh +13
-0+case "${2}" in + --add-rpi3-config-enable-uart) + if ! grep -qE 'enable_uart=1' "${BINARIES_DIR}/rpi-firmware/config.txt"; then + echo "Adding 'enable_uart=1' to config.txt." + cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt" + +# fixes rpi3 console +enable_uart=1 +__EOF__ + fi + ;; +esac +# Mark the kernel as DT-enabled
mkdir -p "${BINARIES_DIR}/kernel-marked" ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \board/raspberrypi/readme.txt +1
-1@@ -58,7 +58,7 @@ After building, you should obtain this tree: +-- rpi-firmware/ | +-- bootcode.bin | +-- cmdline.txt - | +-- config.txt + | +-- config.txt [3] | +-- fixup.dat | `-- start.elf +-- sdcard.img@@ -69,6 +69,10 @@ After building, you should obtain this tree:[2] This is the mkknlimg DT-marked kernel.
+[3] For Pi 3 an additional 'enable_uart=1' will be added to fix
board/raspberrypi/readme.txt +3
-0+ (serial) console output. Alternatives are 'dtoverlay=pi3-miniuart-bt' + or 'dtoverlay=pi3-disable-bt'. +How to write the SD card
========================
Quoted 13 lines
Quoted 9 lines
configs/raspberrypi3_defconfig +0
-0@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y # BR2_TARGET_ROOTFS_TAR is not setBR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh" BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart?
This lowers the core clock speed to minimum, so if you are doing some high definition video decode or interlace then you might want this disabled. I would recommend keeping it disabled by default.
Is this (maybe) a vote for my initial proposed patch ([1]) to add dtoverlay=pi3-miniuart-bt?
The current situation for Pi 3 (no dtoerlay, no enable_uart) is no serial console and an unusable default console on HDMI (with a doubled (but unusable) login prompt)...
Regards,
Peter
Quoted 9 lines
Quoted 8 lines
--
2.8.1_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot
PATCH 1/1 raspberrypi3: fix serial console (add enable_uart=1)
Hello Khem Raj,
Quoted 79 lines · Peter Seiderer
Hello Khem Raj,
Quoted 61 lines · Khem Raj
Quoted 61 lines · Peter Seiderer
- enhance
post-image.shscript to add 'enable_uart=1' to config.txt on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart" inraspberrypi3_defconfigSigned-off-by Peter Seiderer <[email protected]>---
board/raspberrypi/post-image.sh | 13 +++++++++++++ board/raspberrypi/readme.txt | 6 +++++- configs/raspberrypi3_defconfig | 1 + 3 files changed, 19 insertions(+), 1 deletion(-)board/raspberrypi/post-image.sh +0
-0@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})"GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg" GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
board/raspberrypi/post-image.sh +13
-0+case "${2}" in + --add-rpi3-config-enable-uart) + if ! grep -qE 'enable_uart=1' "${BINARIES_DIR}/rpi-firmware/config.txt"; then + echo "Adding 'enable_uart=1' to config.txt." + cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt" + +# fixes rpi3 console +enable_uart=1 +__EOF__ + fi + ;; +esac +# Mark the kernel as DT-enabled
mkdir -p "${BINARIES_DIR}/kernel-marked" ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \board/raspberrypi/readme.txt +1
-1@@ -58,7 +58,7 @@ After building, you should obtain this tree: +-- rpi-firmware/ | +-- bootcode.bin | +-- cmdline.txt - | +-- config.txt + | +-- config.txt [3] | +-- fixup.dat | `-- start.elf +-- sdcard.img@@ -69,6 +69,10 @@ After building, you should obtain this tree:[2] This is the mkknlimg DT-marked kernel.
+[3] For Pi 3 an additional 'enable_uart=1' will be added to fix
board/raspberrypi/readme.txt +3
-0+ (serial) console output. Alternatives are 'dtoverlay=pi3-miniuart-bt' + or 'dtoverlay=pi3-disable-bt'. +How to write the SD card
========================Quoted 13 lines
Quoted 9 lines
configs/raspberrypi3_defconfig +0
-0@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y # BR2_TARGET_ROOTFS_TAR is not setBR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh" BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart?
This lowers the core clock speed to minimum, so if you are doing some high definition video decode or interlace then you might want this disabled. I would recommend keeping it disabled by default.
Quoted 9 lines
Is this (maybe) a vote for my initial proposed patch ([1]) to add dtoverlay=pi3-miniuart-bt?
The current situation for Pi 3 (no dtoerlay, no
enable_uart) is no serial console and an unusable default console on HDMI (with a doubled (but unusable) login prompt)...Regards,
Peter
Sorry, forgot to add the link:
[1] http://lists.busybox.net/pipermail/buildroot/2016-May/160334.html
Regards,
Peter
Quoted 14 lines
Quoted 9 lines
Quoted 8 lines
--
2.8.1_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot
PATCH 1/1 raspberrypi3: fix serial console (add enable_uart=1)
Quoted 86 lines · Peter Seiderer
Hello Khem Raj,
Quoted 82 lines · Peter Seiderer
Hello Khem Raj,
Quoted 61 lines · Khem Raj
Quoted 61 lines · Peter Seiderer
- enhance
post-image.shscript to add 'enable_uart=1' to config.txt on request
- add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart" inraspberrypi3_defconfigSigned-off-by Peter Seiderer <[email protected]>---
board/raspberrypi/post-image.sh | 13 +++++++++++++ board/raspberrypi/readme.txt | 6 +++++- configs/raspberrypi3_defconfig | 1 + 3 files changed, 19 insertions(+), 1 deletion(-)board/raspberrypi/post-image.sh +0
-0@@ -5,6 +5,19 @@ BOARD_NAME="$(basename ${BOARD_DIR})"GENIMAGE_CFG="${BOARD_DIR}/genimage-${BOARD_NAME}.cfg" GENIMAGE_TMP="${BUILD_DIR}/genimage.tmp"
board/raspberrypi/post-image.sh +13
-0+case "${2}" in + --add-rpi3-config-enable-uart) + if ! grep -qE 'enable_uart=1' "${BINARIES_DIR}/rpi-firmware/config.txt"; then + echo "Adding 'enable_uart=1' to config.txt." + cat << __EOF__ >> "${BINARIES_DIR}/rpi-firmware/config.txt" + +# fixes rpi3 console +enable_uart=1 +__EOF__ + fi + ;; +esac +# Mark the kernel as DT-enabled
mkdir -p "${BINARIES_DIR}/kernel-marked" ${HOST_DIR}/usr/bin/mkknlimg "${BINARIES_DIR}/zImage" \board/raspberrypi/readme.txt +1
-1@@ -58,7 +58,7 @@ After building, you should obtain this tree: +-- rpi-firmware/ | +-- bootcode.bin | +-- cmdline.txt - | +-- config.txt + | +-- config.txt [3] | +-- fixup.dat | `-- start.elf +-- sdcard.img@@ -69,6 +69,10 @@ After building, you should obtain this tree:[2] This is the mkknlimg DT-marked kernel.
+[3] For Pi 3 an additional 'enable_uart=1' will be added to fix
board/raspberrypi/readme.txt +3
-0+ (serial) console output. Alternatives are 'dtoverlay=pi3-miniuart-bt' + or 'dtoverlay=pi3-disable-bt'. +How to write the SD card
========================Quoted 13 lines
Quoted 9 lines
configs/raspberrypi3_defconfig +0
-0@@ -34,3 +34,4 @@ BR2_TARGET_ROOTFS_EXT2_4=y # BR2_TARGET_ROOTFS_TAR is not setBR2_ROOTFS_POST_BUILD_SCRIPT="board/raspberrypi3/post-build.sh" BR2_ROOTFS_POST_IMAGE_SCRIPT="board/raspberrypi3/post-image.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="--add-rpi3-config-enable-uart?
This lowers the core clock speed to minimum, so if you are doing some high definition video decode or interlace then you might want this disabled. I would recommend keeping it disabled by default.
Is this (maybe) a vote for my initial proposed patch ([1]) to add dtoverlay=pi3-miniuart-bt?
yes that looks better to me. as long as it is has enable/disable knob
Quoted 29 lines
Quoted 6 lines
The current situation for Pi 3 (no dtoerlay, no
enable_uart) is no serial console and an unusable default console on HDMI (with a doubled (but unusable) login prompt)...Regards,
PeterSorry, forgot to add the link:
[1] http://lists.busybox.net/pipermail/buildroot/2016-May/160334.html
Regards,
PeterQuoted 14 lines
Quoted 9 lines
Quoted 8 lines
--
2.8.1_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot_______________________________________________
buildroot mailing list
buildroot at busybox.net
http://lists.busybox.net/mailman/listinfo/buildroot
PATCH 1/1 raspberrypi3: fix serial console (add enable_uart=1)
In reply to Peter SeidererQuoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
"Peter" == Peter Seiderer <[email protected]> writes:
Hi,
Quoted 9 lines
Quoted 3 lines
This lowers the core clock speed to minimum, so if you are doing some high definition video decode or interlace then you might want this disabled. I would recommend keeping it disabled by default.
Is this (maybe) a vote for my initial proposed patch ([1]) to add dtoverlay=pi3-miniuart-bt?
The current situation for Pi 3 (no dtoerlay, no
enable_uart) is no serial console and an unusable default console on HDMI (with a doubled (but unusable) login prompt)...
Yes, I guess having a flakey/less-performant bluetooth connection is less bad than the alternatives ..
Signature · 1 line
Bye, Peter Korsgaard