problems with CRC in fw_printenv and fw_setenv utility and use
Hello all,
I have built the binary fw_printenv by using mtd-user.h from mtd-utils on the internet as it fw_printenv won't compile it without using that file. So I have used mtd-user.h and mtd-abi.h. The contents of my configuration file are
# MTD device name Device offset Env. size Flash sector size /dev/mtd1 0x0000 0x4000 0x4000
When I run fw_printenv it complained with error Warning : Bad CRC using default environment in env_init function in fw_env.c source code. To gain a better understanding I print the value crc1 calculated using crc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are different crc1_ok is not set and I get the error. Any clue as to why these values would be different?
When I use the fw_setenv utility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on /dev/mtd1: Invalid argument
Error: can't write fw_env to flash
I want to be able to set bootvars and print bootvars from user space Linux code. Linux has support for mtd-utils we tested the mtd-utils interface.
I look forward to your replies. I appreciate your help.
Thanks and Regards
Signature · 2 lines
View this message in context: http://www.nabble.com/problems-with-CRC-in-fw_printenv-and-fw_setenv-utility-and-use-tp14767876p14767876.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Quoted 3 lines · u-boot user
I have built the binary
fw_printenvby usingmtd-user.hfrom mtd-utils on the internet as itfw_printenvwon't compile it without using that file. So
So you're obviously not using the newest version of U-Boot, what you should. Make sure to read the updated README in tools/env/.
Quoted 4 lines
I have used
mtd-user.handmtd-abi.h. The contents of my configuration file are# MTD device name Device offset Env. size Flash sector size /dev/mtd1 0x0000 0x4000 0x4000
Is this in /etc/ ?
Quoted 8 lines
When I run
fw_printenvit complained with error Warning : Bad CRC using default environment inenv_initfunction infw_env.csource code. To gain a better understanding I print the value crc1 calculated usingcrc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are differentcrc1_okis not set and I get the error. Any clue as to why these values would be different?
Probably some mismatch between the information in your config file and the real environment. Where is you're environment located in flash? Is your mtd partitioning right? What does
$ cat /proc/mtd
show?
Quoted 10 lines
When I use the
fw_setenvutility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on/dev/mtd1: Invalid argument
Error: can't writefw_envto flash
Weird. I would guess your MTD partitioning is wrong.
Best regards
Markus Klotzbuecher
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
Hello,
Can you please tell me how to build the fw_setenv and fw_printenv using
the mtd-user.h file? I am new to Linux. Please help. I don't see mtd/ in proc/ directory.
Thanks
Quoted 37 lines · u-boot user
Hello all,
I have built the binary
fw_printenvby usingmtd-user.hfrom mtd-utils on the internet as itfw_printenvwon't compile it without using that file. So I have usedmtd-user.handmtd-abi.h. The contents of my configuration file are# MTD device name Device offset Env. size Flash sector size /dev/mtd1 0x0000 0x4000 0x4000When I run
fw_printenvit complained with error Warning : Bad CRC using default environment inenv_initfunction infw_env.csource code. To gain a better understanding I print the value crc1 calculated usingcrc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are differentcrc1_okis not set and I get the error. Any clue as to why these values would be different?When I use the
fw_setenvutility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on/dev/mtd1: Invalid argument
Error: can't writefw_envto flashI want to be able to set bootvars and print bootvars from user space Linux code. Linux has support for mtd-utils we tested the mtd-utils interface.
I look forward to your replies. I appreciate your help.
Thanks and Regards
Signature · 2 lines
View this message in context: http://www.nabble.com/problems-with-CRC-in-fw_printenv-and-fw_setenv-utility-and-use-tp14767876p15502924.html Sent from the Uboot - Users mailing list archive at Nabble.com.
Quoted 2 lines · techie_vasu
Can you please tell me how to build the
fw_setenvandfw_printenvusing
Please make sure to read tools/env/README from *top of tree* U-Boot sources.
Quoted 2 lines
the
mtd-user.hfile? I am new to Linux. Please help. I don't see mtd/ in proc/ directory.
What kernel version? Looks like you have not compiled in mtd support.
Best regards
Markus Klotzbuecher
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de
Hello,
Can you please tell me how to build the fw_setenv and fw_printenv using
the mtd-user.h file? I am new to Linux. Please help. I don't see mtd/ in proc/ directory.
Thanks
Quoted 37 lines · u-boot user
Hello all,
I have built the binary
fw_printenvby usingmtd-user.hfrom mtd-utils on the internet as itfw_printenvwon't compile it without using that file. So I have usedmtd-user.handmtd-abi.h. The contents of my configuration file are# MTD device name Device offset Env. size Flash sector size /dev/mtd1 0x0000 0x4000 0x4000When I run
fw_printenvit complained with error Warning : Bad CRC using default environment inenv_initfunction infw_env.csource code. To gain a better understanding I print the value crc1 calculated usingcrc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are differentcrc1_okis not set and I get the error. Any clue as to why these values would be different?When I use the
fw_setenvutility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on/dev/mtd1: Invalid argument
Error: can't writefw_envto flashI want to be able to set bootvars and print bootvars from user space Linux code. Linux has support for mtd-utils we tested the mtd-utils interface.
I look forward to your replies. I appreciate your help.
Thanks and Regards
Signature · 2 lines
View this message in context: http://www.nabble.com/problems-with-CRC-in-fw_printenv-and-fw_setenv-utility-and-use-tp14767876p15502930.html Sent from the Uboot - Users mailing list archive at Nabble.com.