Skip to contentSkip to conversation

problems with CRC in fw_printenv and fw_setenv utility and use

U-Boot-Users u-boot user 3 participants 5 messages Jan 12, 2008 – Feb 15, 2008

lore
Share & tools
lore
#0 lore raw

Hello all,

I have built the binary fw_printenv by using mtd-user.h from mtd-utils on the internet as it fw_printenv won't compile it without using that file. So I have used mtd-user.h and mtd-abi.h. The contents of my configuration file are

# MTD device name       Device offset   Env. size       Flash sector size
/dev/mtd1               0x0000          0x4000          0x4000 

When I run fw_printenv it complained with error Warning : Bad CRC using default environment in env_init function in fw_env.c source code. To gain a better understanding I print the value crc1 calculated using crc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are different crc1_ok is not set and I get the error. Any clue as to why these values would be different?

When I use the fw_setenv utility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on /dev/mtd1: Invalid argument
Error: can't write fw_env to flash

I want to be able to set bootvars and print bootvars from user space Linux code. Linux has support for mtd-utils we tested the mtd-utils interface.

I look forward to your replies. I appreciate your help.

Thanks and Regards

Signature · 2 lines
View this message in context: http://www.nabble.com/problems-with-CRC-in-fw_printenv-and-fw_setenv-utility-and-use-tp14767876p14767876.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#1 lore raw
Quoted 3 lines · u-boot user

I have built the binary fw_printenv by using mtd-user.h from mtd-utils on the internet as it fw_printenv won't compile it without using that file. So

So you're obviously not using the newest version of U-Boot, what you should. Make sure to read the updated README in tools/env/.

Quoted 4 lines

I have used mtd-user.h and mtd-abi.h. The contents of my configuration file are

# MTD device name       Device offset   Env. size       Flash sector size
/dev/mtd1               0x0000          0x4000          0x4000 

Is this in /etc/ ?

Quoted 8 lines

When I run fw_printenv it complained with error Warning : Bad CRC using default environment in env_init function in fw_env.c source code. To gain a better understanding I print the value crc1 calculated using crc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are different crc1_ok is not set and I get the error. Any clue as to why these values would be different?

Probably some mismatch between the information in your config file and the real environment. Where is you're environment located in flash? Is your mtd partitioning right? What does

$ cat /proc/mtd

show?

Quoted 10 lines

When I use the fw_setenv utility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on /dev/mtd1: Invalid argument
Error: can't write fw_env to flash

Weird. I would guess your MTD partitioning is wrong.

Best regards

Markus Klotzbuecher

--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de

#2 lore raw
In reply to u-boot user

Hello,

Can you please tell me how to build the fw_setenv and fw_printenv using
the mtd-user.h file? I am new to Linux. Please help. I don't see mtd/ in proc/ directory.

Thanks

Quoted 37 lines · u-boot user

Hello all,

I have built the binary fw_printenv by using mtd-user.h from mtd-utils on the internet as it fw_printenv won't compile it without using that file. So I have used mtd-user.h and mtd-abi.h. The contents of my configuration file are

# MTD device name       Device offset   Env. size       Flash sector size
/dev/mtd1               0x0000          0x4000          0x4000 

When I run fw_printenv it complained with error Warning : Bad CRC using default environment in env_init function in fw_env.c source code. To gain a better understanding I print the value crc1 calculated using crc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are different crc1_ok is not set and I get the error. Any clue as to why these values would be different?

When I use the fw_setenv utility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on /dev/mtd1: Invalid argument
Error: can't write fw_env to flash

I want to be able to set bootvars and print bootvars from user space Linux code. Linux has support for mtd-utils we tested the mtd-utils interface.

I look forward to your replies. I appreciate your help.

Thanks and Regards

Signature · 2 lines
View this message in context: http://www.nabble.com/problems-with-CRC-in-fw_printenv-and-fw_setenv-utility-and-use-tp14767876p15502924.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#4 lore raw
In reply to u-boot user

Hello,

Can you please tell me how to build the fw_setenv and fw_printenv using
the mtd-user.h file? I am new to Linux. Please help. I don't see mtd/ in proc/ directory.

Thanks

Quoted 37 lines · u-boot user

Hello all,

I have built the binary fw_printenv by using mtd-user.h from mtd-utils on the internet as it fw_printenv won't compile it without using that file. So I have used mtd-user.h and mtd-abi.h. The contents of my configuration file are

# MTD device name       Device offset   Env. size       Flash sector size
/dev/mtd1               0x0000          0x4000          0x4000 

When I run fw_printenv it complained with error Warning : Bad CRC using default environment in env_init function in fw_env.c source code. To gain a better understanding I print the value crc1 calculated using crc32(0,environment.data,ENV_SIZE). The value it prints is CRC computed:FE641197
If I print the environment.crc value it is D0CA8A0E. As the checksum values are different crc1_ok is not set and I get the error. Any clue as to why these values would be different?

When I use the fw_setenv utility to set an environment variable it gives the following errors
Writing CRC value to flash: D0C78567
Unlocking flash...
Other dev values are: 0
Current dev value: 0
Done
Erasing old environment...
MTD erase error on /dev/mtd1: Invalid argument
Error: can't write fw_env to flash

I want to be able to set bootvars and print bootvars from user space Linux code. Linux has support for mtd-utils we tested the mtd-utils interface.

I look forward to your replies. I appreciate your help.

Thanks and Regards

Signature · 2 lines
View this message in context: http://www.nabble.com/problems-with-CRC-in-fw_printenv-and-fw_setenv-utility-and-use-tp14767876p15502930.html
Sent from the Uboot - Users mailing list archive at Nabble.com.
#3 lore raw
In reply to techie_vasu
Quoted 2 lines · techie_vasu

Can you please tell me how to build the fw_setenv and fw_printenv using

Please make sure to read tools/env/README from *top of tree* U-Boot sources.

Quoted 2 lines

the mtd-user.h file? I am new to Linux. Please help. I don't see mtd/ in proc/ directory.

What kernel version? Looks like you have not compiled in mtd support.

Best regards

Markus Klotzbuecher

--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-0 Fax: +49-8142-66989-80 Email: office at denx.de