Skip to contentSkip to conversation

am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD

PATCH In review Keerthy 2 participants 3 messages Nov 30, 2016 – Dec 12, 2016

lore
Share & tools
lore

Keerthy

author
#0 lore raw

PATCH 1/1 am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD

The GPIO7 pad mux should be programmed to POWERHOLD value as per board design. In cases where the PMIC is shut off the mux is set to GPIO7 mode. So during initialization to be on the safer side set the mode to POWERHOLD.

---
 board/ti/am57xx/board.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)
board/ti/am57xx/board.c +17 -0
index f3e3f0b..5fd39bd 100644
@@ -49,6 +49,9 @@ DECLARE_GLOBAL_DATA_PTR;
 
 #define SYSINFO_BOARD_NAME_MAX_LEN	45
 
+#define TPS65903X_PRIMARY_SECONDARY_PAD2	0xFB
+#define TPS65903X_PAD2_POWERHOLD_MASK		0x20
+
 const struct omap_sysinfo sysinfo = {
 	"Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n"
 };
@@ -380,12 +383,26 @@ int board_init(void)
 int board_late_init(void)
 {
 	setup_board_eeprom_env();
+	u8 val;
 
 	/*
 	 * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds
 	 * This is the POWERHOLD-in-Low behavior.
 	 */
 	palmas_i2c_write_u8(TPS65903X_CHIP_P1, 0xA0, 0x1);
+
+	/*
+	 * Set the GPIO7 Pad to POWERHOLD. This has higher priority
+	 * over DEV_CTRL.DEV_ON bit. This can be reset in case of
+	 * PMIC Power off. So to be on the safer side set it back
+	 * to POWERHOLD mode irrespective of the current state.
+	 */
+	palmas_i2c_read_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
+			   &val);
+	val = val | TPS65903X_PAD2_POWERHOLD_MASK;
+	palmas_i2c_write_u8(TPS65903X_CHIP_P1, TPS65903X_PRIMARY_SECONDARY_PAD2,
+			    val);
+
 	return 0;
 }
 
Signature · 1 line
1.9.1
#1 lore raw

PATCH 1/1 am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD

Quoted 6 lines · Keerthy

The GPIO7 pad mux should be programmed to POWERHOLD value as per board design. In cases where the PMIC is shut off the mux is set to GPIO7 mode. So during initialization to be on the safer side set the mode to POWERHOLD.

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161201/0b96b34a/attachment.sig>
#2 lore raw
In reply to Keerthy
Quoted 7 lines · Keerthy

The GPIO7 pad mux should be programmed to POWERHOLD value as per board design. In cases where the PMIC is shut off the mux is set to GPIO7 mode. So during initialization to be on the safer side set the mode to POWERHOLD.

Applied to u-boot/master, thanks!

Signature · 8 lines
Tom
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: Digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161212/8ecc4c25/attachment.sig>