am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD
PATCH 1/1 am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD
The GPIO7 pad mux should be programmed to POWERHOLD value as per board design. In cases where the PMIC is shut off the mux is set to GPIO7 mode. So during initialization to be on the safer side set the mode to POWERHOLD.
--- board/ti/am57xx/board.c | 17 +++++++++++++++++ 1 file changed, 17 insertions(+)
board/ti/am57xx/board.c +17 -0
@@ -49,6 +49,9 @@ DECLARE_GLOBAL_DATA_PTR;#define SYSINFO_BOARD_NAME_MAX_LEN 45 +#define TPS65903X_PRIMARY_SECONDARY_PAD2 0xFB +#define TPS65903X_PAD2_POWERHOLD_MASK 0x20 +const struct omap_sysinfo sysinfo = {"Board: UNKNOWN(BeagleBoard X15?) REV UNKNOWN\n" };
@@ -380,12 +383,26 @@ int board_init(void)int board_late_init (void ) {setup_board_eeprom_env (); +u8 val;/* * DEV_CTRL.DEV_ON = 1 please - else palmas switches off in 8 seconds * This is the POWERHOLD-in-Low behavior. */ palmas_i2c_write_u8 (TPS65903X_CHIP_P1 ,0xA0 ,0x1 ); + +/* +* Set the GPIO7 Pad to POWERHOLD. This has higher priority +* over DEV_CTRL.DEV_ON bit. This can be reset in case of +* PMIC Power off. So to be on the safer side set it back +* to POWERHOLD mode irrespective of the current state. +*/ +palmas_i2c_read_u8 (TPS65903X_CHIP_P1 ,TPS65903X_PRIMARY_SECONDARY_PAD2 , + &val); + val = val |TPS65903X_PAD2_POWERHOLD_MASK ; +palmas_i2c_write_u8 (TPS65903X_CHIP_P1 ,TPS65903X_PRIMARY_SECONDARY_PAD2 , + val); +return 0 ; }
Signature · 1 line
1.9.1
PATCH 1/1 am57xx: Set tps659038 PMIC GPIO7 pad mux value to POWERHOLD
Quoted 6 lines · Keerthy
The GPIO7 pad mux should be programmed to POWERHOLD value as per board design. In cases where the PMIC is shut off the mux is set to GPIO7 mode. So during initialization to be on the safer side set the mode to POWERHOLD.
Signed-off-by Keerthy <[email protected]>
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161201/0b96b34a/attachment.sig>
Quoted 7 lines · Keerthy
The GPIO7 pad mux should be programmed to POWERHOLD value as per board design. In cases where the PMIC is shut off the mux is set to GPIO7 mode. So during initialization to be on the safer side set the mode to POWERHOLD.
Signed-off-by Keerthy <[email protected]>Reviewed-by Tom Rini <[email protected]>
Applied to u-boot/master, thanks!
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20161212/8ecc4c25/attachment.sig>