Skip to contentSkip to conversation

HDMI 2.0: Scrambling in DRM layer

PATCH Superseded Shashank Sharma 3 participants 9 messages Mar 3, 2017 – Mar 7, 2017

Subsystems (4)

v7 of 10 Superseded Latest is v10 →

lore
Share & tools
lore
#0 lore raw

v7 cover HDMI 2.0: Scrambling in DRM layer

HDMI 2.0 spec defines a method to reduce the RF footprint while operating at higher pixel clocks, which is called Scrambling. Scrambling can be controlled over a new set of I2C registers which are accessible over existing DDC I2C lines, called SCDC register set.

This patch series contains 6 patches:
- First two patches add generic drm helper functions to read and write into SCDC registers. These patches are written by Thierry, in a patch series published here:
https://patchwork.kernel.org/patch/9459051/
Minor changes were done to map the patches into this series.

- Next two patches add functions for scrambling detection and scrambling control.

- Next two patches use this infrastructure in DRM layer from I915 driver, to enable scrambling on a GLK deivce which sports a native HDMI 2.0 controller.

V2:
- addressed review comments from Thierry, Ville and Dhinakaran
- added signed-off-by:self in first two patches(Jani N)

V3:
- addressed review comments from Jose and Jani

V4:
- addressed review comments from Maarten on patch 5, rebase all other patches

V5:
- addressed review comments from Ville/Ander on patch 1, 4, 5 rebase all other patches

V6:
- addressed review comments from Ville on patch 4, 5 rebase all other patches

V7:
- addressed review comments from Ander on patch 5
rebase all other patches,
added r-b from Jose on patch 3,4

Shashank Sharma (4):
drm/edid: detect SCDC support in HF-VSDB
drm/edid: detect SCDC support in HF-VSDB
drm/i915: enable scrambling
drm/i915: allow HDMI 2.0 clock rates

Thierry Reding (2):
drm: Add SCDC helpers
drm/edid: check for HF-VSDB block

 Documentation/gpu/drm-kms-helpers.rst |  12 ++
 drivers/gpu/drm/Makefile              |   3 +-
 drivers/gpu/drm/drm_edid.c            |  60 +++++++++
 drivers/gpu/drm/drm_scdc_helper.c     | 244 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/i915_reg.h       |   7 +
 drivers/gpu/drm/i915/intel_ddi.c      |  33 +++++
 drivers/gpu/drm/i915/intel_display.c  |   3 +
 drivers/gpu/drm/i915/intel_drv.h      |  10 ++
 drivers/gpu/drm/i915/intel_hdmi.c     |  54 ++++++++
 include/drm/drm_connector.h           |  52 ++++++++
 include/drm/drm_edid.h                |   1 -
 include/drm/drm_scdc_helper.h         | 159 ++++++++++++++++++++++
 include/linux/hdmi.h                  |   1 +
 13 files changed, 637 insertions(+), 2 deletions(-)
 create mode 100644 drivers/gpu/drm/drm_scdc_helper.c
 create mode 100644 include/drm/drm_scdc_helper.h
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#1 lore raw

PATCH v7 1/6 drm: Add SCDC helpers

From: Thierry Reding <[email protected]>

SCDC is a mechanism defined in the HDMI 2.0 specification that allows the source and sink devices to communicate.

This commit introduces helpers to access the SCDC and provides the symbolic names for the various registers defined in the specification.

V2: Rebase.
V3: Added R-B from Jose.
V4: Rebase
V5: Addressed review comments from Ville
- Handle the I2c return values in a better way (dp_dual_mode)
- Make the macros for SCDC Major/Minor more readable, by adding a 'GET' in the macro names
V6: Rebase
V7: Rebase

---
 Documentation/gpu/drm-kms-helpers.rst |  12 ++++
 drivers/gpu/drm/Makefile              |   3 +-
 drivers/gpu/drm/drm_scdc_helper.c     | 123 +++++++++++++++++++++++++++++++
 include/drm/drm_scdc_helper.h         | 132 ++++++++++++++++++++++++++++++++++
 4 files changed, 269 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/drm_scdc_helper.c
 create mode 100644 include/drm/drm_scdc_helper.h
Documentation/gpu/drm-kms-helpers.rst +12 -0
index 03040aa..7592756 100644
@@ -217,6 +217,18 @@ EDID Helper Functions Reference
 .. kernel-doc:: drivers/gpu/drm/drm_edid.c
    :export:
 
+SCDC Helper Functions Reference
+===============================
+
+.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c
+   :doc: scdc helpers
+
+.. kernel-doc:: include/drm/drm_scdc_helper.h
+   :internal:
+
+.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c
+   :export:
+
 Rectangle Utilities Reference
 =============================
 
drivers/gpu/drm/Makefile +2 -1
index 3ee9579..da5b08c 100644
@@ -31,7 +31,8 @@ drm-$(CONFIG_DEBUG_FS) += drm_debugfs.o drm_debugfs_crc.o
 drm_kms_helper-y := drm_crtc_helper.o drm_dp_helper.o drm_probe_helper.o \
 		drm_plane_helper.o drm_dp_mst_topology.o drm_atomic_helper.o \
 		drm_kms_helper_common.o drm_dp_dual_mode_helper.o \
-		drm_simple_kms_helper.o drm_modeset_helper.o
+		drm_simple_kms_helper.o drm_modeset_helper.o \
+		drm_scdc_helper.o
 
 drm_kms_helper-$(CONFIG_DRM_LOAD_EDID_FIRMWARE) += drm_edid_load.o
 drm_kms_helper-$(CONFIG_DRM_FBDEV_EMULATION) += drm_fb_helper.o
drivers/gpu/drm/drm_scdc_helper.c new file +123 -0

123 lines not on this page · raw message

include/drm/drm_scdc_helper.h new file +132 -0

132 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

PATCH v7 2/6 drm/edid: check for HF-VSDB block

In reply to Shashank Sharma

From: Thierry Reding <[email protected]>

This patch implements a small function that finds if a given CEA db is hdmi-forum vendor specific data block or not.

V2: Rebase.
V3: Added R-B from Jose.
V4: Rebase
V5: Rebase
V6: Rebase
V7: Rebase

---
 drivers/gpu/drm/drm_edid.c | 15 +++++++++++++++
 include/linux/hdmi.h       |  1 +
 2 files changed, 16 insertions(+)
drivers/gpu/drm/drm_edid.c +15 -0
index 5da5a85..3e0aafa 100644
@@ -3251,6 +3251,21 @@ static bool cea_db_is_hdmi_vsdb(const u8 *db)
 	return hdmi_id == HDMI_IEEE_OUI;
 }
 
+static bool cea_db_is_hdmi_forum_vsdb(const u8 *db)
+{
+	unsigned int oui;
+
+	if (cea_db_tag(db) != VENDOR_BLOCK)
+		return false;
+
+	if (cea_db_payload_len(db) < 7)
+		return false;
+
+	oui = db[3] << 16 | db[2] << 8 | db[1];
+
+	return oui == HDMI_FORUM_IEEE_OUI;
+}
+
 #define for_each_cea_db(cea, i, start, end) \
 	for ((i) = (start); (i) < (end) && (i) + cea_db_payload_len(&(cea)[(i)]) < (end); (i) += cea_db_payload_len(&(cea)[(i)]) + 1)
 
include/linux/hdmi.h +1 -0
index edbb4fc..d271ff2 100644
@@ -35,6 +35,7 @@ enum hdmi_infoframe_type {
 };
 
 #define HDMI_IEEE_OUI 0x000c03
+#define HDMI_FORUM_IEEE_OUI 0xc45dd8
 #define HDMI_INFOFRAME_HEADER_SIZE  4
 #define HDMI_AVI_INFOFRAME_SIZE    13
 #define HDMI_SPD_INFOFRAME_SIZE    25
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#3 lore raw

PATCH v7 3/6 drm/edid: detect SCDC support in HF-VSDB

In reply to Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.
V6: Rebase.
V6: Added R-B from Jose.

---
 drivers/gpu/drm/drm_edid.c  | 14 ++++++++++++++
 include/drm/drm_connector.h | 33 +++++++++++++++++++++++++++++++++
 2 files changed, 47 insertions(+)
drivers/gpu/drm/drm_edid.c +14 -0
index 3e0aafa..d64b7bd 100644
@@ -3817,6 +3817,18 @@ enum hdmi_quantization_range
 }
 EXPORT_SYMBOL(drm_default_rgb_quant_range);
 
+static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
+				 const u8 *hf_vsdb)
+{
+	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+
+	if (hf_vsdb[6] & 0x80) {
+		hdmi->scdc.supported = true;
+		if (hf_vsdb[6] & 0x40)
+			hdmi->scdc.read_request = true;
+	}
+}
+
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
 					   const u8 *hdmi)
 {
@@ -3931,6 +3943,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,
 
 		if (cea_db_is_hdmi_vsdb(db))
 			drm_parse_hdmi_vsdb_video(connector, db);
+		if (cea_db_is_hdmi_forum_vsdb(db))
+			drm_parse_hdmi_forum_vsdb(connector, db);
 	}
 }
 
include/drm/drm_connector.h +33 -0
index fabb35a..bf9d6f5 100644
@@ -87,6 +87,34 @@ enum subpixel_order {
 	SubPixelVerticalRGB,
 	SubPixelVerticalBGR,
 	SubPixelNone,
+
+};
+
+/*
+ * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
+ *
+ * Provides SCDC register support and capabilities related information on a
+ * HDMI 2.0 sink. In case of a HDMI 1.4 sink, all parameter must be 0.
+ */
+struct drm_scdc {
+	/**
+	 * @supported: status control & data channel present.
+	 */
+	bool supported;
+	/**
+	 * @read_request: sink is capable of generating scdc read request.
+	 */
+	bool read_request;
+};
+
+/**
+ * struct drm_hdmi_info - runtime information about the connected HDMI sink
+ *
+ * Describes if a given display supports advanced HDMI 2.0 features.
+ * This information is available in CEA-861-F extension blocks (like HF-VSDB).
+ */
+struct drm_hdmi_info {
+	struct drm_scdc scdc;
 };
 
 /**
@@ -204,6 +232,11 @@ struct drm_display_info {
 	 * @cea_rev: CEA revision of the HDMI sink.
 	 */
 	u8 cea_rev;
+
+	/**
+	 * @hdmi: advance features of a HDMI sink.
+	 */
+	struct drm_hdmi_info hdmi;
 };
 
 int drm_display_info_set_bus_formats(struct drm_display_info *info,
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#4 lore raw

PATCH v7 4/6 drm/edid: detect SCDC support in HF-VSDB

In reply to Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.
V6: Addressed review comments from Ville
- Add clock rate calculations for 1/10 and 1/40 ratios
- Remove leftovers from old patchset
V7: Added R-B from Jose.

---
 drivers/gpu/drm/drm_edid.c        |  33 ++++++++++-
 drivers/gpu/drm/drm_scdc_helper.c | 121 ++++++++++++++++++++++++++++++++++++++
 include/drm/drm_connector.h       |  19 ++++++
 include/drm/drm_edid.h            |   1 -
 include/drm/drm_scdc_helper.h     |  27 +++++++++
 5 files changed, 199 insertions(+), 2 deletions(-)
drivers/gpu/drm/drm_edid.c +32 -1
index d64b7bd..fad3d44 100644
@@ -37,6 +37,7 @@
 #include <drm/drm_edid.h>
 #include <drm/drm_encoder.h>
 #include <drm/drm_displayid.h>
+#include <drm/drm_scdc_helper.h>
 
 #include "drm_crtc_internal.h"
 
@@ -3820,13 +3821,43 @@ enum hdmi_quantization_range
 static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
 				 const u8 *hf_vsdb)
 {
-	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+	struct drm_display_info *display = &connector->display_info;
+	struct drm_hdmi_info *hdmi = &display->hdmi;
 
 	if (hf_vsdb[6] & 0x80) {
 		hdmi->scdc.supported = true;
 		if (hf_vsdb[6] & 0x40)
 			hdmi->scdc.read_request = true;
 	}
+
+	/*
+	 * All HDMI 2.0 monitors must support scrambling at rates > 340 MHz.
+	 * And as per the spec, three factors confirm this:
+	 * * Availability of a HF-VSDB block in EDID (check)
+	 * * Non zero Max_TMDS_Char_Rate filed in HF-VSDB (let's check)
+	 * * SCDC support available (let's check)
+	 * Lets check it out.
+	 */
+
+	if (hf_vsdb[5]) {
+		/* max clock is 5000 KHz times block value */
+		u32 max_tmds_clock = hf_vsdb[5] * 5000;
+		struct drm_scdc *scdc = &hdmi->scdc;
+
+		if (max_tmds_clock > 340000) {
+			display->max_tmds_clock = max_tmds_clock;
+			DRM_DEBUG_KMS("HF-VSDB: max TMDS clock %d kHz\n",
+				display->max_tmds_clock);
+		}
+
+		if (scdc->supported) {
+			scdc->scrambling.supported = true;
+
+			/* Few sinks support scrambling for cloks < 340M */
+			if ((hf_vsdb[6] & 0x8))
+				scdc->scrambling.low_rates = true;
+		}
+	}
 }
 
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
drivers/gpu/drm/drm_scdc_helper.c +121 -0

132 lines not on this page · raw message

include/drm/drm_connector.h +19 -0
index bf9d6f5..f8b766d 100644
@@ -90,6 +90,20 @@ enum subpixel_order {
 
 };
 
+/**
+ * struct drm_scrambling: sink's scrambling support.
+ */
+struct drm_scrambling {
+	/**
+	 * @supported: scrambling supported for rates > 340 Mhz.
+	 */
+	bool supported;
+	/**
+	 * @low_rates: scrambling supported for rates <= 340 Mhz.
+	 */
+	bool low_rates;
+};
+
 /*
  * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
  *
@@ -105,8 +119,13 @@ struct drm_scdc {
 	 * @read_request: sink is capable of generating scdc read request.
 	 */
 	bool read_request;
+	/**
+	 * @scrambling: sink's scrambling capabilities
+	 */
+	struct drm_scrambling scrambling;
 };
 
+
 /**
  * struct drm_hdmi_info - runtime information about the connected HDMI sink
  *
include/drm/drm_edid.h +0 -1
index 3ead84d..7b9f48b 100644
@@ -476,5 +476,4 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,
 struct drm_display_mode *drm_mode_find_dmt(struct drm_device *dev,
 					   int hsize, int vsize, int fresh,
 					   bool rb);
-
 #endif /* __DRM_EDID_H__ */
include/drm/drm_scdc_helper.h +27 -0
index 9c52deb..ab6bcfb 100644
@@ -129,4 +129,31 @@ static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset,
 	return drm_scdc_write(adapter, offset, &value, sizeof(value));
 }
 
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set);
 #endif
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#5 lore raw

PATCH v7 5/6 drm/i915: enable scrambling

In reply to Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare.

V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits
- Remove platform check in intel_pipe_config_compare while checking scrambling status

---
 drivers/gpu/drm/i915/i915_reg.h      |  7 +++++
 drivers/gpu/drm/i915/intel_ddi.c     | 33 +++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_display.c |  3 +++
 drivers/gpu/drm/i915/intel_drv.h     | 10 +++++++
 drivers/gpu/drm/i915/intel_hdmi.c    | 52 ++++++++++++++++++++++++++++++++++++
 5 files changed, 105 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +7 -0
index 4906ce4d..bfd988b 100644
@@ -7824,7 +7824,14 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
+#define  TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \
+					| TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \
+					| TRANS_DDI_HDMI_SCRAMBLING)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +33 -0
index a7c08d7..2159b2b 100644
@@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
 			temp |= TRANS_DDI_MODE_SELECT_HDMI;
 		else
 			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (intel_crtc->config->hdmi_scrambling)
+			temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK;
+		if (intel_crtc->config->hdmi_high_tmds_clock_ratio)
+			temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
 	} else if (type == INTEL_OUTPUT_ANALOG) {
 		temp |= TRANS_DDI_MODE_SELECT_FDI;
 		temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
@@ -1885,6 +1890,20 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);
 
+		if (IS_GEMINILAKE(dev_priv)) {
+			/*
+			 * GLK sports a native HDMI 2.0 controller. If required
+			 * clock rate is > 340 Mhz && scrambling is supported
+			 * by sink, enable scrambling before enabling the
+			 * HDMI 2.0 port. The sink can choose to disable the
+			 * scrambling if it doesn't detect a scrambled within
+			 * 100 ms.
+			 */
+			intel_hdmi_handle_sink_scrambling(intel_encoder,
+						conn_state->connector,
+						pipe_config, true);
+		}
+
 		/* In HDMI/DVI mode, the port width, and swing/emphasis values
 		 * are ignored so nothing special needs to be done besides
 		 * enabling the port.
@@ -1917,6 +1936,14 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
 	if (old_crtc_state->has_audio)
 		intel_audio_codec_disable(intel_encoder);
 
+	if (type == INTEL_OUTPUT_HDMI) {
+		struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+					old_conn_state->connector,
+					intel_crtc->config, false);
+	}
+
 	if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
@@ -2044,6 +2071,12 @@ void intel_ddi_get_config(struct intel_encoder *encoder,
 
 		if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config))
 			pipe_config->has_infoframe = true;
+
+		if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) ==
+				TRANS_DDI_HDMI_SCRAMBLING_MASK)
+			pipe_config->hdmi_scrambling = true;
+		if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE)
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
 		/* fall through */
 	case TRANS_DDI_MODE_SELECT_DVI:
 		pipe_config->lane_count = 4;
drivers/gpu/drm/i915/intel_display.c +3 -0
index 99e8d9c..21d64c0 100644
@@ -11662,6 +11662,9 @@ static void __printf(3, 4)
 	if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		PIPE_CONF_CHECK_I(limited_color_range);
+
+	PIPE_CONF_CHECK_I(hdmi_scrambling);
+	PIPE_CONF_CHECK_I(hdmi_high_tmds_clock_ratio);
 	PIPE_CONF_CHECK_I(has_infoframe);
 
 	PIPE_CONF_CHECK_I(has_audio);
drivers/gpu/drm/i915/intel_drv.h +10 -0
index e6fbbee..62fbeb2 100644
@@ -695,6 +695,12 @@ struct intel_crtc_state {
 
 	/* Gamma mode programmed on the pipe */
 	uint32_t gamma_mode;
+
+	/* HDMI scrambling status (sink) */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio (sink) */
+	bool hdmi_high_tmds_clock_ratio;
 };
 
 struct vlv_wm_state {
@@ -1626,6 +1632,10 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
 bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 			       struct intel_crtc_state *pipe_config,
 			       struct drm_connector_state *conn_state);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+					struct drm_connector *connector,
+					struct intel_crtc_state *config,
+					bool enable);
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +52 -0

76 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#6 lore raw

Re: [PATCH v7 5/6] drm/i915: enable scrambling

Quoted 94 lines · Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare.

V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits
- Remove platform check in intel_pipe_config_compare while checking scrambling status

---
 drivers/gpu/drm/i915/i915_reg.h      |  7 +++++
 drivers/gpu/drm/i915/intel_ddi.c     | 33 +++++++++++++++++++++++
 drivers/gpu/drm/i915/intel_display.c |  3 +++
 drivers/gpu/drm/i915/intel_drv.h     | 10 +++++++
 drivers/gpu/drm/i915/intel_hdmi.c    | 52 ++++++++++++++++++++++++++++++++++++
 5 files changed, 105 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +7 -0
index 4906ce4d..bfd988b 100644
@@ -7824,7 +7824,14 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
+#define  TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \
+					| TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \
+					| TRANS_DDI_HDMI_SCRAMBLING)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +5 -0
index a7c08d7..2159b2b 100644
@@ -1311,6 +1311,11 @@ void intel_ddi_enable_transcoder_func(struct drm_crtc *crtc)
 			temp |= TRANS_DDI_MODE_SELECT_HDMI;
 		else
 			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (intel_crtc->config->hdmi_scrambling)
+			temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK;
+		if (intel_crtc->config->hdmi_high_tmds_clock_ratio)
+			temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
 	} else if (type == INTEL_OUTPUT_ANALOG) {
 		temp |= TRANS_DDI_MODE_SELECT_FDI;
 		temp |= (intel_crtc->config->fdi_lanes - 1) << 1;
@@ -1885,6 +1890,20 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);

drivers/gpu/drm/i915/intel_ddi.c static void intel_enable_ddi(struct intel_encoder *intel_encoder, · line 1901

Quoted 10 lines
drivers/gpu/drm/i915/intel_ddi.c +9 -0
 
+		if (IS_GEMINILAKE(dev_priv)) {
+			/*
+			 * GLK sports a native HDMI 2.0 controller. If required
+			 * clock rate is > 340 Mhz && scrambling is supported
+			 * by sink, enable scrambling before enabling the
+			 * HDMI 2.0 port. The sink can choose to disable the
+			 * scrambling if it doesn't detect a scrambled within
+			 * 100 ms.
+			 */

This comment seems out of place, it explains what's the effect of calling intel_hdmi_handle_sink_scrambling(). That should be in that function's kernel doc instead, which I now realize is missing.

Quoted 9 lines
drivers/gpu/drm/i915/intel_ddi.c +5 -0
+			intel_hdmi_handle_sink_scrambling(intel_encoder,
+						conn_state->connector,
+						pipe_config, true);
+		}
+
 		/* In HDMI/DVI mode, the port width, and swing/emphasis values
 		 * are ignored so nothing special needs to be done besides
 		 * enabling the port.

drivers/gpu/drm/i915/intel_ddi.c static void intel_disable_ddi(struct intel_encoder *intel_encoder, · line 1944

Quoted 9 lines
drivers/gpu/drm/i915/intel_ddi.c +6 -0
@@ -1917,6 +1936,14 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
 	if (old_crtc_state->has_audio)
 		intel_audio_codec_disable(intel_encoder);
 
+	if (type == INTEL_OUTPUT_HDMI) {
+		struct intel_crtc *intel_crtc = to_intel_crtc(encoder->crtc);
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+					old_conn_state->connector,
+					intel_crtc->config, false);

I'm wondering if this should old_crtc_state instead? If I remember right, crtc_state fields that are not explicitly preserved are zeroed, so handle_sink_scrambling() won't actually disable scrambling here.

Also, there's an asymmetry between this and the enable path, since that checks for IS_GEMINILAKE() and this doesn't. Would it make sense to move the check into intel_hdmi_handle_sink_scrambling()? Ville?

drivers/gpu/drm/i915/intel_ddi.c void intel_ddi_get_config(struct intel_encoder *encoder, · line 2076

Quoted 12 lines
drivers/gpu/drm/i915/intel_ddi.c +5 -0
+	}
+
 	if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
@@ -2044,6 +2071,12 @@ void intel_ddi_get_config(struct intel_encoder *encoder,
 
 		if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config))
 			pipe_config->has_infoframe = true;
+
+		if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) ==
+				TRANS_DDI_HDMI_SCRAMBLING_MASK)

This is misaligned.

Ander

Quoted 122 lines
drivers/gpu/drm/i915/intel_ddi.c +3 -0
+			pipe_config->hdmi_scrambling = true;
+		if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE)
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
 		/* fall through */
 	case TRANS_DDI_MODE_SELECT_DVI:
 		pipe_config->lane_count = 4;
drivers/gpu/drm/i915/intel_display.c +3 -0
index 99e8d9c..21d64c0 100644
@@ -11662,6 +11662,9 @@ static void __printf(3, 4)
 	if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		PIPE_CONF_CHECK_I(limited_color_range);
+
+	PIPE_CONF_CHECK_I(hdmi_scrambling);
+	PIPE_CONF_CHECK_I(hdmi_high_tmds_clock_ratio);
 	PIPE_CONF_CHECK_I(has_infoframe);
 
 	PIPE_CONF_CHECK_I(has_audio);
drivers/gpu/drm/i915/intel_drv.h +10 -0
index e6fbbee..62fbeb2 100644
@@ -695,6 +695,12 @@ struct intel_crtc_state {
 
 	/* Gamma mode programmed on the pipe */
 	uint32_t gamma_mode;
+
+	/* HDMI scrambling status (sink) */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio (sink) */
+	bool hdmi_high_tmds_clock_ratio;
 };
 
 struct vlv_wm_state {
@@ -1626,6 +1632,10 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
 bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 			       struct intel_crtc_state *pipe_config,
 			       struct drm_connector_state *conn_state);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+					struct drm_connector *connector,
+					struct intel_crtc_state *config,
+					bool enable);
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +45 -0
index c2184f7..c6e2398 100644
@@ -34,6 +34,7 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc.h>
 #include <drm/drm_edid.h>
+#include <drm/drm_scdc_helper.h>
 #include "intel_drv.h"
 #include <drm/i915_drm.h>
 #include <drm/intel_lpe_audio.h>
@@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base);
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc;
 	int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock;
 	int clock_12bpc = clock_8bpc * 3 / 2;
 	int desired_bpp;
@@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 
 	pipe_config->lane_count = 4;
 
+	if (scdc->scrambling.supported && IS_GEMINILAKE(dev_priv)) {
+		if (scdc->scrambling.low_rates)
+			pipe_config->hdmi_scrambling = true;
+
+		if (pipe_config->port_clock > 340000) {
+			pipe_config->hdmi_scrambling = true;
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
+		}
+	}
+
 	return true;
 }
 
@@ -1794,6 +1806,46 @@ static void intel_hdmi_destroy(struct drm_connector *connector)
 	intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE;
 }
 
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+				       struct drm_connector *connector,
+				       struct intel_crtc_state *config,
+				       bool enable)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&intel_encoder->base);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	struct drm_scrambling *scrambling =
+				&connector->display_info.hdmi.scdc.scrambling;
+	struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv,
+							  intel_hdmi->ddc_bus);
+	bool ret;
+
+	if (!scrambling->supported)
+		return;
+
+	DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n",
+			intel_encoder->base.name, connector->name);
+
+	if (config->hdmi_high_tmds_clock_ratio) {
+		/* Set TMDS bit clock ratio to 1/40 or 1/10 */
+		ret = drm_scdc_set_high_tmds_clock_ratio(adptr, enable);
+		if (!ret) {
+			DRM_ERROR("Set TMDS ratio failed\n");
+			return;
+		}
+	}
+
+	if (config->hdmi_scrambling) {
+		/* Enable/disable sink scrambling */
+		ret = drm_scdc_set_scrambling(adptr, enable);
+		if (!ret) {
+			DRM_ERROR("Set sink scrambling failed\n");

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1851

Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +7 -0
+			return;
+		}
+	}
+
+	DRM_DEBUG_KMS("sink scrambling handled\n");
+}
+
 static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv,
 			     enum port port)
 {

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#7 lore raw

PATCH v7 6/6 drm/i915: allow HDMI 2.0 clock rates

In reply to Shashank Sharma

Geminilake has a native HDMI 2.0 controller, which is capable of driving clocks upto 594Mhz. This patch updates the max tmds clock limit for the same.

V2: rebase
V3: rebase
V4: added r-b from Ander
V5: rebase
V6: rebase
V7: rebase

---
 drivers/gpu/drm/i915/intel_hdmi.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
index c6e2398..9f401db 100644
@@ -1209,6 +1209,8 @@ static int intel_hdmi_source_max_tmds_clock(struct drm_i915_private *dev_priv)
 {
 	if (IS_G4X(dev_priv))
 		return 165000;
+	else if (IS_GEMINILAKE(dev_priv))
+		return 594000;
 	else if (IS_HASWELL(dev_priv) || INTEL_INFO(dev_priv)->gen >= 8)
 		return 300000;
 	else
Signature · 6 lines
1.9.1

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#8 lore raw

✗ Fi.CI.BAT: failure for HDMI 2.0: Scrambling in DRM layer (rev7)

In reply to Shashank Sharma
== Series Details ==

== Series Details ==

Series: HDMI 2.0: Scrambling in DRM layer (rev7)
URL : https://patchwork.freedesktop.org/series/19161/
State : failure

== Summary ==

drivers/gpu/drm/i915/intel_drv.h:741:1: error: expected identifier or ‘(’ before ‘}’ token
};
^
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/i915_debugfs.o' failed
make[4]: *** [drivers/gpu/drm/i915/i915_debugfs.o] Error 1
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/render.o' failed
make[4]: *** [drivers/gpu/drm/i915/gvt/render.o] Error 1
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/intel_color.o' failed
make[4]: *** [drivers/gpu/drm/i915/intel_color.o] Error 1
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/edid.o' failed
make[4]: *** [drivers/gpu/drm/i915/gvt/edid.o] Error 1
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/i915_vgpu.o' failed
make[4]: *** [drivers/gpu/drm/i915/i915_vgpu.o] Error 1
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/intel_panel.o' failed
make[4]: *** [drivers/gpu/drm/i915/intel_panel.o] Error 1
In file included from drivers/gpu/drm/i915/intel_i2c.c:33:0:
drivers/gpu/drm/i915/intel_drv.h:728:1: error: expected specifier-qualifier-list before ‘<<’ token
<<<<<<< 00443e2f2748abed9b675965899308a77dd76128
^
drivers/gpu/drm/i915/intel_drv.h:728:9: error: invalid suffix "f2748abed9b675965899308a77dd76128" on floating constant
<<<<<<< 00443e2f2748abed9b675965899308a77dd76128

         ^

drivers/gpu/drm/i915/intel_drv.h:737:1: error: expected identifier or ‘(’ before ‘>>’ token

Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line

drm/i915: enable scrambling

^
drivers/gpu/drm/i915/intel_drv.h:741:1: error: expected identifier or ‘(’ before ‘}’ token
};
^
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/intel_crt.o' failed make[4]: *** [drivers/gpu/drm/i915/intel_crt.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/cfg_space.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/cfg_space.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/gvt.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/gvt.o] Error 1
LD drivers/video/fbdev/built-in.o
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/mmio.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/mmio.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/scheduler.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/scheduler.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/firmware.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/firmware.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/execlist.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/execlist.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/intel_i2c.o' failed make[4]: *** [drivers/gpu/drm/i915/intel_i2c.o] Error 1
LD drivers/video/console/built-in.o
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/display.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/display.o] Error 1
LD drivers/video/built-in.o
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/intel_display.o' failed make[4]: *** [drivers/gpu/drm/i915/intel_display.o] Error 1 scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/cmd_parser.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/cmd_parser.o] Error 1
LD drivers/gpu/drm/drm.o
LD drivers/pci/built-in.o
scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/handlers.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/handlers.o] Error 1

  LD      drivers/tty/serial/8250/8250_base.o
  LD      drivers/tty/serial/8250/built-in.o
  LD      drivers/usb/core/usbcore.o
  LD      drivers/tty/serial/built-in.o
  LD      drivers/usb/core/built-in.o
  LD      fs/btrfs/btrfs.o

scripts/Makefile.build:294: recipe for target 'drivers/gpu/drm/i915/gvt/gtt.o' failed make[4]: *** [drivers/gpu/drm/i915/gvt/gtt.o] Error 1 scripts/Makefile.build:553: recipe for target 'drivers/gpu/drm/i915' failed make[3]: *** [drivers/gpu/drm/i915] Error 2
scripts/Makefile.build:553: recipe for target 'drivers/gpu/drm' failed make[2]: *** [drivers/gpu/drm] Error 2
scripts/Makefile.build:553: recipe for target 'drivers/gpu' failed make[1]: *** [drivers/gpu] Error 2
make[1]: *** Waiting for unfinished jobs....

  CC      arch/x86/kernel/cpu/capflags.o
  LD      arch/x86/kernel/cpu/built-in.o
  LD      net/ipv4/built-in.o
  LD      drivers/scsi/sd_mod.o
  LD [M]  drivers/net/ethernet/intel/igbvf/igbvf.o
  LD      drivers/scsi/built-in.o
  LD      arch/x86/kernel/built-in.o
  LD      fs/btrfs/built-in.o
  LD [M]  drivers/net/ethernet/intel/e1000/e1000.o
  LD      arch/x86/built-in.o
  LD      drivers/usb/host/xhci-hcd.o
  LD      drivers/tty/vt/built-in.o
  LD      drivers/tty/built-in.o
  LD      net/core/built-in.o
  LD [M]  drivers/net/ethernet/intel/igb/igb.o
  LD      net/built-in.o
  LD      drivers/md/md-mod.o
  LD      drivers/md/built-in.o
  LD      drivers/usb/host/built-in.o
  LD      drivers/usb/built-in.o
  LD      fs/ext4/ext4.o
  LD      fs/ext4/built-in.o
  LD      fs/built-in.o
  LD [M]  drivers/net/ethernet/intel/e1000e/e1000e.o
  LD      drivers/net/ethernet/built-in.o
  LD      drivers/net/built-in.o

Makefile:990: recipe for target 'drivers' failed
make: *** [drivers] Error 2

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx