Skip to contentSkip to conversation

HDMI 2.0: Scrambling in DRM layer

PATCH In review Shashank Sharma 4 participants 12 messages Mar 13, 2017 – Mar 25, 2017

Subsystems (4)
lore
Share & tools
lore
#0 lore raw

v10 cover HDMI 2.0: Scrambling in DRM layer

HDMI 2.0 spec defines a method to reduce the RF footprint while operating at higher pixel clocks, which is called Scrambling. Scrambling can be controlled over a new set of I2C registers which are accessible over existing DDC I2C lines, called SCDC register set.

This patch series contains 6 patches:
- First two patches add generic drm helper functions to read and write into SCDC registers. These patches are written by Thierry, in a patch series published here:
https://patchwork.kernel.org/patch/9459051/
Minor changes were done to map the patches into this series.

- Next two patches add functions for scrambling detection and scrambling control.

- Next two patches use this infrastructure in DRM layer from I915 driver, to enable scrambling on a GLK deivce which sports a native HDMI 2.0 controller.

V2:
- addressed review comments from Thierry, Ville and Dhinakaran
- added signed-off-by:self in first two patches(Jani N)

V3:
- addressed review comments from Jose and Jani

V4:
- addressed review comments from Maarten on patch 5, rebase all other patches

V5:
- addressed review comments from Ville/Ander on patch 1, 4, 5 rebase all other patches

V6:
- addressed review comments from Ville on patch 4, 5 rebase all other patches

V7:
- addressed review comments from Ander on patch 5 rebase all other patches,
added r-b from Jose on patch 3,4

V8:
- addressed review comments from Ander on patch 5
- rebase and fixed merge conflict

V9:
- addressed review comments from Ander on patch 5

V10:
- rebase

Shashank Sharma (4):
drm/edid: detect SCDC support in HF-VSDB
drm/edid: detect SCDC support in HF-VSDB
drm/i915: enable scrambling
drm/i915: allow HDMI 2.0 clock rates

Thierry Reding (2):
drm: Add SCDC helpers
drm/edid: check for HF-VSDB block

 Documentation/gpu/drm-kms-helpers.rst |  12 ++
 drivers/gpu/drm/Makefile              |   3 +-
 drivers/gpu/drm/drm_edid.c            |  60 +++++++++
 drivers/gpu/drm/drm_scdc_helper.c     | 244 ++++++++++++++++++++++++++++++++++
 drivers/gpu/drm/i915/i915_reg.h       |   7 +
 drivers/gpu/drm/i915/intel_ddi.c      |  23 ++++
 drivers/gpu/drm/i915/intel_display.c  |   3 +
 drivers/gpu/drm/i915/intel_drv.h      |  10 ++
 drivers/gpu/drm/i915/intel_hdmi.c     |  65 +++++++++
 include/drm/drm_connector.h           |  52 ++++++++
 include/drm/drm_edid.h                |   1 -
 include/drm/drm_scdc_helper.h         | 159 ++++++++++++++++++++++
 include/linux/hdmi.h                  |   1 +
 13 files changed, 638 insertions(+), 2 deletions(-)
 create mode 100644 drivers/gpu/drm/drm_scdc_helper.c
 create mode 100644 include/drm/drm_scdc_helper.h
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#1 lore raw

PATCH v10 1/6 drm: Add SCDC helpers

From: Thierry Reding <[email protected]>

SCDC is a mechanism defined in the HDMI 2.0 specification that allows the source and sink devices to communicate.

This commit introduces helpers to access the SCDC and provides the symbolic names for the various registers defined in the specification.

V2: Rebase.
V3: Added R-B from Jose.
V4: Rebase
V5: Addressed review comments from Ville
- Handle the I2c return values in a better way (dp_dual_mode)
- Make the macros for SCDC Major/Minor more readable, by adding a 'GET' in the macro names
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase

---
 Documentation/gpu/drm-kms-helpers.rst |  12 ++++
 drivers/gpu/drm/Makefile              |   3 +-
 drivers/gpu/drm/drm_scdc_helper.c     | 123 +++++++++++++++++++++++++++++++
 include/drm/drm_scdc_helper.h         | 132 ++++++++++++++++++++++++++++++++++
 4 files changed, 269 insertions(+), 1 deletion(-)
 create mode 100644 drivers/gpu/drm/drm_scdc_helper.c
 create mode 100644 include/drm/drm_scdc_helper.h
Documentation/gpu/drm-kms-helpers.rst +12 -0
index 03040aa..7592756 100644
@@ -217,6 +217,18 @@ EDID Helper Functions Reference
 .. kernel-doc:: drivers/gpu/drm/drm_edid.c
    :export:
 
+SCDC Helper Functions Reference
+===============================
+
+.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c
+   :doc: scdc helpers
+
+.. kernel-doc:: include/drm/drm_scdc_helper.h
+   :internal:
+
+.. kernel-doc:: drivers/gpu/drm/drm_scdc_helper.c
+   :export:
+
 Rectangle Utilities Reference
 =============================
 
drivers/gpu/drm/Makefile +2 -1
index 59aae43..59f0f9b 100644
@@ -31,7 +31,8 @@ drm-$(CONFIG_DEBUG_FS) += drm_debugfs.o drm_debugfs_crc.o
 drm_kms_helper-y := drm_crtc_helper.o drm_dp_helper.o drm_probe_helper.o \
 		drm_plane_helper.o drm_dp_mst_topology.o drm_atomic_helper.o \
 		drm_kms_helper_common.o drm_dp_dual_mode_helper.o \
-		drm_simple_kms_helper.o drm_modeset_helper.o
+		drm_simple_kms_helper.o drm_modeset_helper.o \
+		drm_scdc_helper.o
 
 drm_kms_helper-$(CONFIG_DRM_LOAD_EDID_FIRMWARE) += drm_edid_load.o
 drm_kms_helper-$(CONFIG_DRM_FBDEV_EMULATION) += drm_fb_helper.o
drivers/gpu/drm/drm_scdc_helper.c new file +123 -0

123 lines not on this page · raw message

include/drm/drm_scdc_helper.h new file +132 -0

132 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#2 lore raw

PATCH v10 2/6 drm/edid: check for HF-VSDB block

In reply to Shashank Sharma

From: Thierry Reding <[email protected]>

This patch implements a small function that finds if a given CEA db is hdmi-forum vendor specific data block or not.

V2: Rebase.
V3: Added R-B from Jose.
V4: Rebase
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase

---
 drivers/gpu/drm/drm_edid.c | 15 +++++++++++++++
 include/linux/hdmi.h       |  1 +
 2 files changed, 16 insertions(+)
drivers/gpu/drm/drm_edid.c +15 -0
index 5da5a85..3e0aafa 100644
@@ -3251,6 +3251,21 @@ static bool cea_db_is_hdmi_vsdb(const u8 *db)
 	return hdmi_id == HDMI_IEEE_OUI;
 }
 
+static bool cea_db_is_hdmi_forum_vsdb(const u8 *db)
+{
+	unsigned int oui;
+
+	if (cea_db_tag(db) != VENDOR_BLOCK)
+		return false;
+
+	if (cea_db_payload_len(db) < 7)
+		return false;
+
+	oui = db[3] << 16 | db[2] << 8 | db[1];
+
+	return oui == HDMI_FORUM_IEEE_OUI;
+}
+
 #define for_each_cea_db(cea, i, start, end) \
 	for ((i) = (start); (i) < (end) && (i) + cea_db_payload_len(&(cea)[(i)]) < (end); (i) += cea_db_payload_len(&(cea)[(i)]) + 1)
 
include/linux/hdmi.h +1 -0
index edbb4fc..d271ff2 100644
@@ -35,6 +35,7 @@ enum hdmi_infoframe_type {
 };
 
 #define HDMI_IEEE_OUI 0x000c03
+#define HDMI_FORUM_IEEE_OUI 0xc45dd8
 #define HDMI_INFOFRAME_HEADER_SIZE  4
 #define HDMI_AVI_INFOFRAME_SIZE    13
 #define HDMI_SPD_INFOFRAME_SIZE    25
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#3 lore raw

PATCH v10 3/6 drm/edid: detect SCDC support in HF-VSDB

In reply to Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.
V6: Rebase.
V7: Added R-B from Jose.
V8: Rebase.
V9: Rebase.
V10: Rebase.

---
 drivers/gpu/drm/drm_edid.c  | 14 ++++++++++++++
 include/drm/drm_connector.h | 33 +++++++++++++++++++++++++++++++++
 2 files changed, 47 insertions(+)
drivers/gpu/drm/drm_edid.c +14 -0
index 3e0aafa..d64b7bd 100644
@@ -3817,6 +3817,18 @@ enum hdmi_quantization_range
 }
 EXPORT_SYMBOL(drm_default_rgb_quant_range);
 
+static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
+				 const u8 *hf_vsdb)
+{
+	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+
+	if (hf_vsdb[6] & 0x80) {
+		hdmi->scdc.supported = true;
+		if (hf_vsdb[6] & 0x40)
+			hdmi->scdc.read_request = true;
+	}
+}
+
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
 					   const u8 *hdmi)
 {
@@ -3931,6 +3943,8 @@ static void drm_parse_cea_ext(struct drm_connector *connector,
 
 		if (cea_db_is_hdmi_vsdb(db))
 			drm_parse_hdmi_vsdb_video(connector, db);
+		if (cea_db_is_hdmi_forum_vsdb(db))
+			drm_parse_hdmi_forum_vsdb(connector, db);
 	}
 }
 
include/drm/drm_connector.h +33 -0
index fabb35a..bf9d6f5 100644
@@ -87,6 +87,34 @@ enum subpixel_order {
 	SubPixelVerticalRGB,
 	SubPixelVerticalBGR,
 	SubPixelNone,
+
+};
+
+/*
+ * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
+ *
+ * Provides SCDC register support and capabilities related information on a
+ * HDMI 2.0 sink. In case of a HDMI 1.4 sink, all parameter must be 0.
+ */
+struct drm_scdc {
+	/**
+	 * @supported: status control & data channel present.
+	 */
+	bool supported;
+	/**
+	 * @read_request: sink is capable of generating scdc read request.
+	 */
+	bool read_request;
+};
+
+/**
+ * struct drm_hdmi_info - runtime information about the connected HDMI sink
+ *
+ * Describes if a given display supports advanced HDMI 2.0 features.
+ * This information is available in CEA-861-F extension blocks (like HF-VSDB).
+ */
+struct drm_hdmi_info {
+	struct drm_scdc scdc;
 };
 
 /**
@@ -204,6 +232,11 @@ struct drm_display_info {
 	 * @cea_rev: CEA revision of the HDMI sink.
 	 */
 	u8 cea_rev;
+
+	/**
+	 * @hdmi: advance features of a HDMI sink.
+	 */
+	struct drm_hdmi_info hdmi;
 };
 
 int drm_display_info_set_bus_formats(struct drm_display_info *info,
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#4 lore raw

Re: [Intel-gfx] [PATCH v10 3/6] drm/edid: detect SCDC support in HF-VSDB

include/drm/drm_connector.h enum subpixel_order { · line 117

Quoted 8 lines · Shashank Sharma
include/drm/drm_connector.h +8 -0
+/**
+ * struct drm_hdmi_info - runtime information about the connected HDMI sink
+ *
+ * Describes if a given display supports advanced HDMI 2.0 features.
+ * This information is available in CEA-861-F extension blocks (like HF-VSDB).
+ */
+struct drm_hdmi_info {
+       struct drm_scdc scdc;

This creates a new warning when building docs. Please fix. -Daniel

Signature · 7 lines
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel
#5 lore raw

RE: [Intel-gfx] [PATCH v10 3/6] drm/edid: detect SCDC support in HF-VSDB

Added description for the variable in this patch:
https://patchwork.freedesktop.org/patch/146424/

Regards
Shashank
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Daniel Vetter
Sent: Friday, March 24, 2017 9:08 PM
To: Sharma, Shashank <[email protected]>
Cc: Syrjala, Ville <[email protected]>; Conselvan De Oliveira, Ander <[email protected]>; Vetter, Daniel <[email protected]>; intel-gfx <[email protected]>; dri-devel <[email protected]>
Subject: Re: [Intel-gfx] [PATCH v10 3/6] drm/edid: detect SCDC support in HF-VSDB

include/drm/drm_connector.h enum subpixel_order { · line 117

Quoted 9 lines · Shashank Sharma
include/drm/drm_connector.h +9 -0
+/**
+ * struct drm_hdmi_info - runtime information about the connected 
+HDMI sink
+ *
+ * Describes if a given display supports advanced HDMI 2.0 features.
+ * This information is available in CEA-861-F extension blocks (like HF-VSDB).
+ */
+struct drm_hdmi_info {
+       struct drm_scdc scdc;

This creates a new warning when building docs. Please fix. -Daniel
--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list [email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#6 lore raw

Re: [PATCH v10 3/6] drm/edid: detect SCDC support in HF-VSDB

In reply to Daniel Vetter

Please use updated version of the patch [V4]:
https://patchwork.freedesktop.org/patch/146426/
(previous one had a merge conflict due to my local patch)

Regards
Shashank
-----Original Message-----
From: Sharma, Shashank
Sent: Saturday, March 25, 2017 11:23 AM
To: 'Daniel Vetter' <[email protected]>
Cc: Syrjala, Ville <[email protected]>; Conselvan De Oliveira, Ander <[email protected]>; Vetter, Daniel <[email protected]>; intel-gfx <[email protected]>; dri-devel <[email protected]>
Subject: RE: [Intel-gfx] [PATCH v10 3/6] drm/edid: detect SCDC support in HF-VSDB

Added description for the variable in this patch:
https://patchwork.freedesktop.org/patch/146424/

Regards
Shashank
-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Daniel Vetter
Sent: Friday, March 24, 2017 9:08 PM
To: Sharma, Shashank <[email protected]>
Cc: Syrjala, Ville <[email protected]>; Conselvan De Oliveira, Ander <[email protected]>; Vetter, Daniel <[email protected]>; intel-gfx <[email protected]>; dri-devel <[email protected]>
Subject: Re: [Intel-gfx] [PATCH v10 3/6] drm/edid: detect SCDC support in HF-VSDB

include/drm/drm_connector.h enum subpixel_order { · line 117

Quoted 9 lines · Shashank Sharma
include/drm/drm_connector.h +9 -0
+/**
+ * struct drm_hdmi_info - runtime information about the connected 
+HDMI sink
+ *
+ * Describes if a given display supports advanced HDMI 2.0 features.
+ * This information is available in CEA-861-F extension blocks (like HF-VSDB).
+ */
+struct drm_hdmi_info {
+       struct drm_scdc scdc;

This creates a new warning when building docs. Please fix. -Daniel
--
Daniel Vetter
Software Engineer, Intel Corporation
+41 (0) 79 365 57 48 - http://blog.ffwll.ch
_______________________________________________
Intel-gfx mailing list [email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx

#7 lore raw

PATCH v10 4/6 drm/edid: detect SCDC support in HF-VSDB

In reply to Shashank Sharma

This patch does following:
- Adds a new structure (drm_hdmi_info) in drm_display_info. This structure will be used to save and indicate if sink supports advanced HDMI 2.0 features
- Adds another structure drm_scdc within drm_hdmi_info, to reflect scdc support and capabilities in connected HDMI 2.0 sink.
- Checks the HF-VSDB block for presence of SCDC, and marks it in scdc structure
- If SCDC is present, checks if sink is capable of generating SCDC read request, and marks it in scdc structure.

V2: Addressed review comments
Thierry:
- Fix typos in commit message and make abbreviation consistent across the commit message.
- Change structure object name from hdmi_info -> hdmi
- Fix typos and abbreviations in description of structure drm_hdmi_info end the description with a full stop.
- Create a structure drm_scdc, and keep all information related to SCDC register set (supported, read request supported) etc in it.

Ville:
- Change rr -> read_request
- Call drm_detect_scrambling function drm_parse_hf_vsdb so that all of HF-VSDB parsing can be kept in same function, in incremental patches.

V3: Rebase.
V4: Rebase.
V5: Rebase.
V6: Addressed review comments from Ville
- Add clock rate calculations for 1/10 and 1/40 ratios
- Remove leftovers from old patchset
V7: Added R-B from Jose.
V8: Rebase.
V9: Rebase.
V10: Rebase.

---
 drivers/gpu/drm/drm_edid.c        |  33 ++++++++++-
 drivers/gpu/drm/drm_scdc_helper.c | 121 ++++++++++++++++++++++++++++++++++++++
 include/drm/drm_connector.h       |  19 ++++++
 include/drm/drm_edid.h            |   1 -
 include/drm/drm_scdc_helper.h     |  27 +++++++++
 5 files changed, 199 insertions(+), 2 deletions(-)
drivers/gpu/drm/drm_edid.c +32 -1
index d64b7bd..fad3d44 100644
@@ -37,6 +37,7 @@
 #include <drm/drm_edid.h>
 #include <drm/drm_encoder.h>
 #include <drm/drm_displayid.h>
+#include <drm/drm_scdc_helper.h>
 
 #include "drm_crtc_internal.h"
 
@@ -3820,13 +3821,43 @@ enum hdmi_quantization_range
 static void drm_parse_hdmi_forum_vsdb(struct drm_connector *connector,
 				 const u8 *hf_vsdb)
 {
-	struct drm_hdmi_info *hdmi = &connector->display_info.hdmi;
+	struct drm_display_info *display = &connector->display_info;
+	struct drm_hdmi_info *hdmi = &display->hdmi;
 
 	if (hf_vsdb[6] & 0x80) {
 		hdmi->scdc.supported = true;
 		if (hf_vsdb[6] & 0x40)
 			hdmi->scdc.read_request = true;
 	}
+
+	/*
+	 * All HDMI 2.0 monitors must support scrambling at rates > 340 MHz.
+	 * And as per the spec, three factors confirm this:
+	 * * Availability of a HF-VSDB block in EDID (check)
+	 * * Non zero Max_TMDS_Char_Rate filed in HF-VSDB (let's check)
+	 * * SCDC support available (let's check)
+	 * Lets check it out.
+	 */
+
+	if (hf_vsdb[5]) {
+		/* max clock is 5000 KHz times block value */
+		u32 max_tmds_clock = hf_vsdb[5] * 5000;
+		struct drm_scdc *scdc = &hdmi->scdc;
+
+		if (max_tmds_clock > 340000) {
+			display->max_tmds_clock = max_tmds_clock;
+			DRM_DEBUG_KMS("HF-VSDB: max TMDS clock %d kHz\n",
+				display->max_tmds_clock);
+		}
+
+		if (scdc->supported) {
+			scdc->scrambling.supported = true;
+
+			/* Few sinks support scrambling for cloks < 340M */
+			if ((hf_vsdb[6] & 0x8))
+				scdc->scrambling.low_rates = true;
+		}
+	}
 }
 
 static void drm_parse_hdmi_deep_color_info(struct drm_connector *connector,
drivers/gpu/drm/drm_scdc_helper.c +121 -0

132 lines not on this page · raw message

include/drm/drm_connector.h +19 -0
index bf9d6f5..f8b766d 100644
@@ -90,6 +90,20 @@ enum subpixel_order {
 
 };
 
+/**
+ * struct drm_scrambling: sink's scrambling support.
+ */
+struct drm_scrambling {
+	/**
+	 * @supported: scrambling supported for rates > 340 Mhz.
+	 */
+	bool supported;
+	/**
+	 * @low_rates: scrambling supported for rates <= 340 Mhz.
+	 */
+	bool low_rates;
+};
+
 /*
  * struct drm_scdc - Information about scdc capabilities of a HDMI 2.0 sink
  *
@@ -105,8 +119,13 @@ struct drm_scdc {
 	 * @read_request: sink is capable of generating scdc read request.
 	 */
 	bool read_request;
+	/**
+	 * @scrambling: sink's scrambling capabilities
+	 */
+	struct drm_scrambling scrambling;
 };
 
+
 /**
  * struct drm_hdmi_info - runtime information about the connected HDMI sink
  *
include/drm/drm_edid.h +0 -1
index 3ead84d..7b9f48b 100644
@@ -476,5 +476,4 @@ void drm_edid_get_monitor_name(struct edid *edid, char *name,
 struct drm_display_mode *drm_mode_find_dmt(struct drm_device *dev,
 					   int hsize, int vsize, int fresh,
 					   bool rb);
-
 #endif /* __DRM_EDID_H__ */
include/drm/drm_scdc_helper.h +27 -0
index 9c52deb..ab6bcfb 100644
@@ -129,4 +129,31 @@ static inline int drm_scdc_writeb(struct i2c_adapter *adapter, u8 offset,
 	return drm_scdc_write(adapter, offset, &value, sizeof(value));
 }
 
+/**
+ * drm_scdc_set_scrambling - enable scrambling
+ * @adapter: I2C adapter for DDC channel
+ * @enable: bool to indicate if scrambling is to be enabled/disabled
+ *
+ * Writes the TMDS config register over SCDC channel, and:
+ * enables scrambling when enable = 1
+ * disables scrambling when enable = 0
+ *
+ * Returns:
+ * True if scrambling is set/reset successfully, false otherwise.
+ */
+bool drm_scdc_set_scrambling(struct i2c_adapter *adapter, bool enable);
+
+/**
+ * drm_scdc_set_high_tmds_clock_ratio - set TMDS clock ratio
+ * @adapter: I2C adapter for DDC channel
+ * @set: ret or reset the high clock ratio
+ *
+ * Writes to the TMDS config register over SCDC channel, and:
+ * sets TMDS clock ratio to 1/40 when set = 1
+ * sets TMDS clock ratio to 1/10 when set = 0
+ *
+ * Returns:
+ * True if write is successful, false otherwise.
+ */
+bool drm_scdc_set_high_tmds_clock_ratio(struct i2c_adapter *adapter, bool set);
 #endif
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#8 lore raw

PATCH v10 5/6 drm/i915: enable scrambling

In reply to Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare.

V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits
- Remove platform check in intel_pipe_config_compare while checking scrambling status

V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment

V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling

V10: Rebase

---
 drivers/gpu/drm/i915/i915_reg.h      |  7 ++++
 drivers/gpu/drm/i915/intel_ddi.c     | 23 +++++++++++++
 drivers/gpu/drm/i915/intel_display.c |  3 ++
 drivers/gpu/drm/i915/intel_drv.h     | 10 ++++++
 drivers/gpu/drm/i915/intel_hdmi.c    | 63 ++++++++++++++++++++++++++++++++++++
 5 files changed, 106 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +7 -0
index 19d42e8..a1aae7a 100644
@@ -7831,7 +7831,14 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
+#define  TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \
+					| TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \
+					| TRANS_DDI_HDMI_SCRAMBLING)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +23 -0
index ee341ef..169d2b4 100644
@@ -1309,6 +1309,11 @@ void intel_ddi_enable_transcoder_func(const struct intel_crtc_state *crtc_state)
 			temp |= TRANS_DDI_MODE_SELECT_HDMI;
 		else
 			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (crtc_state->hdmi_scrambling)
+			temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK;
+		if (crtc_state->hdmi_high_tmds_clock_ratio)
+			temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
 	} else if (type == INTEL_OUTPUT_ANALOG) {
 		temp |= TRANS_DDI_MODE_SELECT_FDI;
 		temp |= (crtc_state->fdi_lanes - 1) << 1;
@@ -1881,6 +1886,12 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
 	if (type == INTEL_OUTPUT_HDMI) {
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);
+		bool clock_ratio = pipe_config->hdmi_high_tmds_clock_ratio;
+		bool scrambling = pipe_config->hdmi_scrambling;
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+						  conn_state->connector,
+						  clock_ratio, scrambling);
 
 		/* In HDMI/DVI mode, the port width, and swing/emphasis values
 		 * are ignored so nothing special needs to be done besides
@@ -1914,6 +1925,12 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
 	if (old_crtc_state->has_audio)
 		intel_audio_codec_disable(intel_encoder);
 
+	if (type == INTEL_OUTPUT_HDMI) {
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+						  old_conn_state->connector,
+						  false, false);
+	}
+
 	if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
@@ -2040,6 +2057,12 @@ void intel_ddi_get_config(struct intel_encoder *encoder,
 
 		if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config))
 			pipe_config->has_infoframe = true;
+
+		if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) ==
+			TRANS_DDI_HDMI_SCRAMBLING_MASK)
+			pipe_config->hdmi_scrambling = true;
+		if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE)
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
 		/* fall through */
 	case TRANS_DDI_MODE_SELECT_DVI:
 		pipe_config->lane_count = 4;
drivers/gpu/drm/i915/intel_display.c +3 -0
index 5526a19..5860ea1 100644
@@ -11674,6 +11674,9 @@ static void __printf(3, 4)
 	if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		PIPE_CONF_CHECK_I(limited_color_range);
+
+	PIPE_CONF_CHECK_I(hdmi_scrambling);
+	PIPE_CONF_CHECK_I(hdmi_high_tmds_clock_ratio);
 	PIPE_CONF_CHECK_I(has_infoframe);
 
 	PIPE_CONF_CHECK_I(has_audio);
drivers/gpu/drm/i915/intel_drv.h +10 -0
index 578f7d2..62d767e 100644
@@ -729,6 +729,12 @@ struct intel_crtc_state {
 
 	/* bitmask of visible planes (enum plane_id) */
 	u8 active_planes;
+
+	/* HDMI scrambling status */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio */
+	bool hdmi_high_tmds_clock_ratio;
 };
 
 struct intel_crtc {
@@ -1616,6 +1622,10 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
 bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 			       struct intel_crtc_state *pipe_config,
 			       struct drm_connector_state *conn_state);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+				       struct drm_connector *connector,
+				       bool high_tmds_clock_ratio,
+				       bool scrambling);
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +63 -0

87 lines not on this page · raw message

Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
Reviewed-by on v10 5/6
#9 lore raw

Re: [Intel-gfx] [PATCH v10 5/6] drm/i915: enable scrambling

Quoted 53 lines · Shashank Sharma

Geminilake platform sports a native HDMI 2.0 controller, and is capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec mendates scrambling for these higher clocks, for reduced RF footprint.

This patch checks if the monitor supports scrambling, and if required, enables it during the modeset.

V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling in intel_enable_ddi() before enabling the port.

V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor", so that the implementation could be close to the language of HDMI spec.

V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio

V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the conditions again, just go by the crtc_state flags. This will simplyfy the condition checks.

V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a check for the same in pipe_config_compare.

V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK not any of its bits
- Remove platform check in intel_pipe_config_compare while checking scrambling status

V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment

Quoted 8 lines

V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling

V10: Rebase

Quoted 209 lines
---
 drivers/gpu/drm/i915/i915_reg.h      |  7 ++++
 drivers/gpu/drm/i915/intel_ddi.c     | 23 +++++++++++++
 drivers/gpu/drm/i915/intel_display.c |  3 ++
 drivers/gpu/drm/i915/intel_drv.h     | 10 ++++++
 drivers/gpu/drm/i915/intel_hdmi.c    | 63 ++++++++++++++++++++++++++++++++++++
 5 files changed, 106 insertions(+)
drivers/gpu/drm/i915/i915_reg.h +7 -0
index 19d42e8..a1aae7a 100644
@@ -7831,7 +7831,14 @@ enum {
 #define  TRANS_DDI_EDP_INPUT_B_ONOFF	(5<<12)
 #define  TRANS_DDI_EDP_INPUT_C_ONOFF	(6<<12)
 #define  TRANS_DDI_DP_VC_PAYLOAD_ALLOC	(1<<8)
+#define  TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE (1<<7)
+#define  TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ (1<<6)
 #define  TRANS_DDI_BFI_ENABLE		(1<<4)
+#define  TRANS_DDI_HIGH_TMDS_CHAR_RATE	(1<<4)
+#define  TRANS_DDI_HDMI_SCRAMBLING	(1<<0)
+#define  TRANS_DDI_HDMI_SCRAMBLING_MASK (TRANS_DDI_HDMI_SCRAMBLER_CTS_ENABLE \
+					| TRANS_DDI_HDMI_SCRAMBLER_RESET_FREQ \
+					| TRANS_DDI_HDMI_SCRAMBLING)
 
 /* DisplayPort Transport Control */
 #define _DP_TP_CTL_A			0x64040
drivers/gpu/drm/i915/intel_ddi.c +23 -0
index ee341ef..169d2b4 100644
@@ -1309,6 +1309,11 @@ void intel_ddi_enable_transcoder_func(const struct intel_crtc_state *crtc_state)
 			temp |= TRANS_DDI_MODE_SELECT_HDMI;
 		else
 			temp |= TRANS_DDI_MODE_SELECT_DVI;
+
+		if (crtc_state->hdmi_scrambling)
+			temp |= TRANS_DDI_HDMI_SCRAMBLING_MASK;
+		if (crtc_state->hdmi_high_tmds_clock_ratio)
+			temp |= TRANS_DDI_HIGH_TMDS_CHAR_RATE;
 	} else if (type == INTEL_OUTPUT_ANALOG) {
 		temp |= TRANS_DDI_MODE_SELECT_FDI;
 		temp |= (crtc_state->fdi_lanes - 1) << 1;
@@ -1881,6 +1886,12 @@ static void intel_enable_ddi(struct intel_encoder *intel_encoder,
 	if (type == INTEL_OUTPUT_HDMI) {
 		struct intel_digital_port *intel_dig_port =
 			enc_to_dig_port(encoder);
+		bool clock_ratio = pipe_config->hdmi_high_tmds_clock_ratio;
+		bool scrambling = pipe_config->hdmi_scrambling;
+
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+						  conn_state->connector,
+						  clock_ratio, scrambling);
 
 		/* In HDMI/DVI mode, the port width, and swing/emphasis values
 		 * are ignored so nothing special needs to be done besides
@@ -1914,6 +1925,12 @@ static void intel_disable_ddi(struct intel_encoder *intel_encoder,
 	if (old_crtc_state->has_audio)
 		intel_audio_codec_disable(intel_encoder);
 
+	if (type == INTEL_OUTPUT_HDMI) {
+		intel_hdmi_handle_sink_scrambling(intel_encoder,
+						  old_conn_state->connector,
+						  false, false);
+	}
+
 	if (type == INTEL_OUTPUT_EDP) {
 		struct intel_dp *intel_dp = enc_to_intel_dp(encoder);
 
@@ -2040,6 +2057,12 @@ void intel_ddi_get_config(struct intel_encoder *encoder,
 
 		if (intel_hdmi->infoframe_enabled(&encoder->base, pipe_config))
 			pipe_config->has_infoframe = true;
+
+		if ((temp & TRANS_DDI_HDMI_SCRAMBLING_MASK) ==
+			TRANS_DDI_HDMI_SCRAMBLING_MASK)
+			pipe_config->hdmi_scrambling = true;
+		if (temp & TRANS_DDI_HIGH_TMDS_CHAR_RATE)
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
 		/* fall through */
 	case TRANS_DDI_MODE_SELECT_DVI:
 		pipe_config->lane_count = 4;
drivers/gpu/drm/i915/intel_display.c +3 -0
index 5526a19..5860ea1 100644
@@ -11674,6 +11674,9 @@ static void __printf(3, 4)
 	if ((INTEL_GEN(dev_priv) < 8 && !IS_HASWELL(dev_priv)) ||
 	    IS_VALLEYVIEW(dev_priv) || IS_CHERRYVIEW(dev_priv))
 		PIPE_CONF_CHECK_I(limited_color_range);
+
+	PIPE_CONF_CHECK_I(hdmi_scrambling);
+	PIPE_CONF_CHECK_I(hdmi_high_tmds_clock_ratio);
 	PIPE_CONF_CHECK_I(has_infoframe);
 
 	PIPE_CONF_CHECK_I(has_audio);
drivers/gpu/drm/i915/intel_drv.h +10 -0
index 578f7d2..62d767e 100644
@@ -729,6 +729,12 @@ struct intel_crtc_state {
 
 	/* bitmask of visible planes (enum plane_id) */
 	u8 active_planes;
+
+	/* HDMI scrambling status */
+	bool hdmi_scrambling;
+
+	/* HDMI High TMDS char rate ratio */
+	bool hdmi_high_tmds_clock_ratio;
 };
 
 struct intel_crtc {
@@ -1616,6 +1622,10 @@ void intel_hdmi_init_connector(struct intel_digital_port *intel_dig_port,
 bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 			       struct intel_crtc_state *pipe_config,
 			       struct drm_connector_state *conn_state);
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *intel_encoder,
+				       struct drm_connector *connector,
+				       bool high_tmds_clock_ratio,
+				       bool scrambling);
 void intel_dp_dual_mode_set_tmds_output(struct intel_hdmi *hdmi, bool enable);
 
 
drivers/gpu/drm/i915/intel_hdmi.c +56 -0
index c2184f7..23b3387 100644
@@ -34,6 +34,7 @@
 #include <drm/drm_atomic_helper.h>
 #include <drm/drm_crtc.h>
 #include <drm/drm_edid.h>
+#include <drm/drm_scdc_helper.h>
 #include "intel_drv.h"
 #include <drm/i915_drm.h>
 #include <drm/intel_lpe_audio.h>
@@ -1316,6 +1317,7 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base);
 	struct drm_i915_private *dev_priv = to_i915(encoder->base.dev);
 	struct drm_display_mode *adjusted_mode = &pipe_config->base.adjusted_mode;
+	struct drm_scdc *scdc = &conn_state->connector->display_info.hdmi.scdc;
 	int clock_8bpc = pipe_config->base.adjusted_mode.crtc_clock;
 	int clock_12bpc = clock_8bpc * 3 / 2;
 	int desired_bpp;
@@ -1385,6 +1387,16 @@ bool intel_hdmi_compute_config(struct intel_encoder *encoder,
 
 	pipe_config->lane_count = 4;
 
+	if (scdc->scrambling.supported && IS_GEMINILAKE(dev_priv)) {
+		if (scdc->scrambling.low_rates)
+			pipe_config->hdmi_scrambling = true;
+
+		if (pipe_config->port_clock > 340000) {
+			pipe_config->hdmi_scrambling = true;
+			pipe_config->hdmi_high_tmds_clock_ratio = true;
+		}
+	}
+
 	return true;
 }
 
@@ -1794,6 +1806,57 @@ static void intel_hdmi_destroy(struct drm_connector *connector)
 	intel_hdmi->aspect_ratio = HDMI_PICTURE_ASPECT_NONE;
 }
 
+/*
+ * intel_hdmi_handle_sink_scrambling: handle sink scrambling/clock ratio setup
+ * @encoder: intel_encoder
+ * @connector: drm_connector
+ * @high_tmds_clock_ratio = bool to indicate if the function needs to set
+ *  or reset the high tmds clock ratio for scrambling
+ * @scrambling: bool to Indicate if the function needs to set or reset
+ *  sink scrambling
+ *
+ * This function handles scrambling on HDMI 2.0 capable sinks.
+ * If required clock rate is > 340 Mhz && scrambling is supported by sink
+ * it enables scrambling. This should be called before enabling the HDMI
+ * 2.0 port, as the sink can choose to disable the scrambling if it doesn't
+ * detect a scrambled clock within 100 ms.
+ */
+void intel_hdmi_handle_sink_scrambling(struct intel_encoder *encoder,
+				       struct drm_connector *connector,
+				       bool high_tmds_clock_ratio,
+				       bool scrambling)
+{
+	struct intel_hdmi *intel_hdmi = enc_to_intel_hdmi(&encoder->base);
+	struct drm_i915_private *dev_priv = connector->dev->dev_private;
+	struct drm_scrambling *sink_scrambling =
+				&connector->display_info.hdmi.scdc.scrambling;
+	struct i2c_adapter *adptr = intel_gmbus_get_adapter(dev_priv,
+							   intel_hdmi->ddc_bus);
+	bool ret;
+
+	if (!sink_scrambling->supported)
+		return;
+
+	DRM_DEBUG_KMS("Setting sink scrambling for enc:%s connector:%s\n",
+		      encoder->base.name, connector->name);
+
+	/* Set TMDS bit clock ratio to 1/40 or 1/10 */
+	ret = drm_scdc_set_high_tmds_clock_ratio(adptr, high_tmds_clock_ratio);
+	if (!ret) {
+		DRM_ERROR("Set TMDS ratio failed\n");
+		return;
+	}
+
+	/* Enable/disable sink scrambling */
+	ret = drm_scdc_set_scrambling(adptr, scrambling);
+	if (!ret) {

drivers/gpu/drm/i915/intel_hdmi.c static void intel_hdmi_destroy(struct drm_connector *connector) · line 1862

Quoted 10 lines
drivers/gpu/drm/i915/intel_hdmi.c +7 -0
+		DRM_ERROR("Set sink scrambling failed\n");
+		return;
+	}
+
+	DRM_DEBUG_KMS("sink scrambling handled\n");
+}
+
 static u8 intel_hdmi_ddc_pin(struct drm_i915_private *dev_priv,
 			     enum port port)
 {

_______________________________________________
dri-devel mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/dri-devel

#10 lore raw

PATCH v10 6/6 drm/i915: allow HDMI 2.0 clock rates

In reply to Shashank Sharma

Geminilake has a native HDMI 2.0 controller, which is capable of driving clocks upto 594Mhz. This patch updates the max tmds clock limit for the same.

V2: rebase
V3: rebase
V4: added r-b from Ander
V5: rebase
V6: rebase
V7: rebase
V8: rebase
V9: rebase
V10: rebase

---
 drivers/gpu/drm/i915/intel_hdmi.c | 2 ++
 1 file changed, 2 insertions(+)
drivers/gpu/drm/i915/intel_hdmi.c +2 -0
index 23b3387..f14aa39 100644
@@ -1209,6 +1209,8 @@ static int intel_hdmi_source_max_tmds_clock(struct drm_i915_private *dev_priv)
 {
 	if (IS_G4X(dev_priv))
 		return 165000;
+	else if (IS_GEMINILAKE(dev_priv))
+		return 594000;
 	else if (IS_HASWELL(dev_priv) || INTEL_INFO(dev_priv)->gen >= 8)
 		return 300000;
 	else
Signature · 6 lines
1.9.1

_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
#11 lore raw

✓ Fi.CI.BAT: success for HDMI 2.0: Scrambling in DRM layer (rev10)

In reply to Shashank Sharma
== Series Details ==

== Series Details ==

Series: HDMI 2.0: Scrambling in DRM layer (rev10)
URL : https://patchwork.freedesktop.org/series/19161/
State : success

== Summary ==

Series 19161v10 HDMI 2.0: Scrambling in DRM layer
https://patchwork.freedesktop.org/api/1.0/series/19161/revisions/10/mbox/

Test gvt_basic:

        Subgroup invalid-placeholder-test:
                incomplete -> SKIP       (fi-hsw-4770r)
fi-bdw-5557u     total:278  pass:267  dwarn:0   dfail:0   fail:0   skip:11  time: 477s
fi-bsw-n3050     total:278  pass:239  dwarn:0   dfail:0   fail:0   skip:39  time: 608s
fi-bxt-j4205     total:278  pass:259  dwarn:0   dfail:0   fail:0   skip:19  time: 535s
fi-bxt-t5700     total:278  pass:257  dwarn:1   dfail:0   fail:0   skip:20  time: 585s
fi-byt-j1900     total:278  pass:251  dwarn:0   dfail:0   fail:0   skip:27  time: 504s
fi-byt-n2820     total:278  pass:247  dwarn:0   dfail:0   fail:0   skip:31  time: 503s
fi-hsw-4770      total:278  pass:262  dwarn:0   dfail:0   fail:0   skip:16  time: 433s
fi-hsw-4770r     total:278  pass:262  dwarn:0   dfail:0   fail:0   skip:16  time: 443s
fi-ilk-650       total:278  pass:228  dwarn:0   dfail:0   fail:0   skip:50  time: 448s
fi-ivb-3520m     total:278  pass:260  dwarn:0   dfail:0   fail:0   skip:18  time: 502s
fi-ivb-3770      total:278  pass:260  dwarn:0   dfail:0   fail:0   skip:18  time: 489s
fi-kbl-7500u     total:278  pass:259  dwarn:1   dfail:0   fail:0   skip:18  time: 466s
fi-skl-6260u     total:278  pass:268  dwarn:0   dfail:0   fail:0   skip:10  time: 500s
fi-skl-6700hq    total:278  pass:261  dwarn:0   dfail:0   fail:0   skip:17  time: 590s
fi-skl-6700k     total:278  pass:256  dwarn:4   dfail:0   fail:0   skip:18  time: 492s
fi-skl-6770hq    total:278  pass:268  dwarn:0   dfail:0   fail:0   skip:10  time: 544s
fi-snb-2520m     total:278  pass:250  dwarn:0   dfail:0   fail:0   skip:28  time: 552s
fi-snb-2600      total:278  pass:249  dwarn:0   dfail:0   fail:0   skip:29  time: 422s

4169859871c0d838e71c317f9c6c68ba0e0b13f5 drm-tip: 2017y-03m-13d-11h-08m-03s UTC integration manifest c71f5c6 drm/i915: allow HDMI 2.0 clock rates
ea1202d drm/i915: enable scrambling
452c888 drm/edid: detect SCDC support in HF-VSDB
a0c921b drm/edid: detect SCDC support in HF-VSDB
08583ae drm/edid: check for HF-VSDB block
b252797 drm: Add SCDC helpers

== Logs ==

For more details see: https://intel-gfx-ci.01.org/CI/Patchwork_4152/
_______________________________________________
Intel-gfx mailing list
[email protected]
https://lists.freedesktop.org/mailman/listinfo/intel-gfx